ZTE | MF65M | User manual | ZTE MF65M User manual

ZTE MF65M User manual
MF65M
Quick Start Guide
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
1
Getting to Know Your Device
Appearance
The following figure is for your reference only.
1. LED Indicators
2. Power Key
3. WPS Key
4. Charging/micro-USB Jack
5. (U)SIM Card Slot
6. microSDHC Card Slot
NOTE:
The microSDHC™ logo
is a trademark of SD-3C,
LLC.
2
Getting to Know Your Device
Indicators
When the device is powered on, the following icons may
be lighting. For a description of the icons, refer to the
following table.
Indicator
Status
Description
Red solid
Error status. Not registered
to the mobile network, no
(U)SIM card inserted or no
network service available.
Network
Registered to the mobile
network.
Green solid
Connected to the mobile
Green blinking network and data is being
transferred.
Wi-Fi
Blue solid
Wi-Fi is active.
Blue blinking WPS is active.
Wi-Fi is off or your device
is in sleep mode.
Off
3
Getting to Know Your Device
SMS
You have unread
messages.
Blue solid
Blue blinking You have new messages.
Off
No unread messages.
Red solid /
blinking
Battery
The battery is low. Please
charge the battery.
The battery is being
Green blinking charged or in standby
mode.
Green solid
The battery level is middle
or high.
Off
Your device is not being
charged, or the battery is
not inserted.
4
Getting to Know Your Device
Connection Scenarios
The device can access the Internet in two ways and it
allows multiple clients to surf on the Internet at the same
time. The following figures are for your reference only.
•
3G Mode: A (U)SIM card can be used to access the
Internet.
Internet Wi-Fi Mode: Your device can be connected
to a WLAN device (such as a hotspot device or
wireless router) through Wi-Fi to access the Internet.
The WLAN device must be already connected to the
Internet.
NOTE: Your device and the WLAN device must be in
different subnets.
•
5
Getting to Know Your Device
Installing Your Device
1. Slide the back cover and remove it.
NOTE:
Do not remove the cover rudely.
2. Install a (U)SIM card to the (U)SIM card slot.
WARNING! Your device does not support the micro/nanoSIM card or any other non-standard SIM cards. To avoid
damaging the device, do not use those cards or any card
holders.
6
Installing Your Device
3.
Install the microSDHC card if necessary.
7
Installing Your Device
4.
Install the battery.
5.
Close the back cover.
8
Connecting to Your Device
Using Wi-Fi
1.
2.
Power on your device.
Make sure your computer or other client devices
have enabled Wi-Fi, and search for available wireless
networks.
NOTE:
Refer to your Wi-Fi-enabled client device manual for
further details on how to search for wireless networks. If
you use a computer, you need to set your computer to
obtain an IP address automatically.
3. Select the Wi-Fi name (SSID) of your device, and
click Connect.
4. Enter the Wi-Fi password if necessary, and click OK.
NOTE:
Refer to the chapter Getting to Know the Wi-Fi SSID and
Password to get the default Wi-Fi SSID and password.
5. Wait until the client device is connected to your device
successfully.
9
Connecting to Your Device
Using a USB Cable
1.
2.
Connect a computer to your device with a USB cable.
Power on your device. The operating system detects
and identifies new hardware, and automatically
installs the hardware.
NOTE:
If the system does not automatically launch installation,
you can click the device installation icon in My Computer
to install.
3. Wait until the computer is connected to your device
successfully.
Getting to Know the Wi-Fi SSID and
Password
You can view the label on the device to get the default
Wi-Fi SSID and password.
10
Logging in to the 3G Mobile Hotspot
Configuration Page
1.
2.
3.
Make sure the connection between your device and
the client device is correct.
Launch the Internet browser and enter
http://192.168.0.1 or http://m.home in the address bar.
NOTE: It is recommended that you use IE (7.0 or later), Firefox (15.0 or later), Opera (10.0 or later), Safari
(4.0 or later), or Google Chrome (10.0 or later).
Enter the password to log in to the 3G Mobile Hotspot
configuration page.
NOTE: The default password is admin.
Changing the Wi-Fi SSID or Password
1.
2.
3.
4.
Log in to the 3G Mobile Hotspot configuration page.
Select Settings > Wi-Fi Settings > Basic Settings.
Change the Network Name (SSID) or the Pass
Phrase (Password).
Click Apply.
11
Accessing the Internet
3G Mode
After a client device is successfully connected to your
device, you can access the Internet in Automatic or
Manual mode. The default mode is Automatic.
Mode
Automatic
Operation
Your device is automatically connected to
the Internet, and you can surf on the Internet through the client.
1.
2.
Manual
3.
Log in to the 3G Mobile Hotspot configuration page.
Select Settings > Network Settings
> Dial-up Settings > WAN Connection Mode > Manual, and then click
Apply.
Select Home, and click Connect or
Disconnect.
NOTE:
To modify the parameters of your device, log in to the 3G
Mobile Hotspot configuration page.
12
Accessing the Internet
Internet Wi-Fi Mode
1.
2.
3.
4.
Log in to the 3G Mobile Hotspot configuration page.
Select Settings > Internet Wi-Fi.
Set the Internet Wi-Fi Switch and Preferred
Network, and click Apply.
You need to set Internet Wi-Fi Switch to Enable and
Preferred Network to Wi-Fi.
5. Connect to the Wi-Fi hotspot.
The following two methods are for your reference.
u
Select a Wi-Fi hotspot listed in the Wi-Fi Hotspot
area, enter a pass phrase in the Pass Phrase text box
and click Apply.
u
Click Add, enter the Wi-Fi hotspot information in the
Add Wi-Fi Hotspot area, and click Apply.
13
Accessing the Internet
After the client device is connected to the Wi-Fi hotspot
successfully, you can access the Internet.
Configuring Your PC
The following procedure describes how to configure the
Internet Protocol in the Windows 7 operating system for
your Wi-Fi connection.
1. Right-click Network and select Properties.
2. Select Change adapter settings.
3. Right-click Wireless Network Connection and select
Properties.
4. Select Internet Protocol Version 4 (TCP/IPv4), and
click Properties.
5. Select Obtain an IP address automatically and Obtain
DNS server address automatically, and click OK.
14
Warning and Notice
To the Owner
•
•
•
•
If inadequately shielded, some electronic devices, for
example, the electronic system of vehicles, may be
affected by the electromagnetic interference caused
by the device. Consult the manufacturers of such devices before using the device if necessary.
Operating the device may interfere with medical
instruments such as hearing aids and pacemakers.
Always keep the device more than 20 centimeters
away from such medical instruments when your device is powered on. Power off the device if necessary.
Consult a physician or the manufacturers of medical
instruments before using the device if necessary.
Be aware of the usage limitation when using the device at places such as oil warehouses or chemical
factories, where there are explosive gases or explosive products being processed. Power off the device if
necessary.
Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and
obey all warning signs, and power off the device in
these conditions.
15
Warning and Notice
•
•
•
•
Do not touch the inner antenna area unless necessary. Otherwise the performance of the device may be
affected.
Do not use the device in an enclosed environment
or where heat dissipation is poor. Prolonged work
in such space may cause excessive heat and raise
ambient temperature, which may lead to automatic
shutdown of the device for your safety. In the case of
such event, cool the device in a well-ventilated place
before turning on for normal use.
Keep the device out of the reach of small children.
The device may cause an injury if used as a toy.
When the device is operating, do not touch the metallic parts. Failing to do so may cause burns.
To the Users
•
Use original accessories or accessories that are authorized. Using any unauthorized accessories may
affect the performance of the device and violate the
related national regulations about telecom terminals.
16
Warning and Notice
•
•
•
•
•
•
Avoid using the device near or inside metallic constructions or establishments that can emit electromagnetic waves, because signal reception may be
affected.
The device is not waterproof. Keep the device dry and
store it in a shady and cool place.
Do not use the device immediately after a sudden
temperature change, because dew may be generated
inside and outside the device. Do not use it until it becomes dry.
Handle the device carefully. Do not drop, bend or
strike it. Otherwise the device may be damaged.
Only qualified personnel can dismantle and repair the
device.
An operating temperature between -10°C and +45°C
and humidity between 5% and 95% are recommended.
Using Battery
Do not change the battery in your device by yourself. The
battery can only be changed by ZTE or ZTE authorized
service provider.
17
Warning and Notice
Limited Warranty
This warranty does not apply to defects or errors in the
product caused by:
i.
Reasonable abrasion.
ii. End users’ failure to follow ZTE’s installation,
operation or maintenance instructions or procedures.
iii. End users’ mishandling, misuse, negligence, or
improper installation, disassembly, storage, servicing or operation of the product.
iv. Modifications or repairs not provided by ZTE or a
ZTE-certified individual.
v. Power failures, surges, fire, flood, accidents, and
actions of third parties or other events outside
ZTE’s reasonable control.
vi. Usage of third-party products or usage in conjunction with third-party products if such defects
are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for the product.
18
Warning and Notice
End users have no right to reject or return the product,
or receive a refund for the product from ZTE under the
above-mentioned situations.
This warranty is end users’ sole remedy and ZTE’s sole
liability for defective or nonconforming items, and is in lieu
of all other warranties, expressed, implied or statutory,
including but not limited to the implied warranties of
merchantability and fitness for a particular purpose, unless
otherwise required under the mandatory provisions of the
law.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect,
special, incidental or consequential damages resulting
from or arising out of or in connection with using of
this product, no matter whether or not ZTE had been
advised, knew or should have known of the possibility of
such damages, including, but not limited to lost profits,
interruption of business, cost of capital, cost of substitute
facilities or product, or any downtime cost.
19
LEGAL INFORMATION
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced,
translated or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve
the right to make modifications on print errors or update
specifications without prior notice.
Version No.: R1.0
Edition Time: August 13, 2014
Manual No.: 079584506816
20
Troubleshooting
Problem
The connection
between your
device and a PC
through a USB
cable cannot be
established.
Recommended Action
•
•
•
The connection
•
between your
device and a client •
through Wi-Fi
cannot be
established.
•
Install the software, and run the
installation program in the path
of My Computer.
If the driver of your device is
abnormal, reinstall the software.
You need to uninstall the software first.
Ensure that the Wi-Fi function is
enabled.
Refresh the network list and select the correct SSID.
Check the IP address, and
ensure that your client can automatically obtain an IP address.
Enter the correct network key
(Wi-Fi password) when you connect the client to your device.
21
Troubleshooting
Problem
Recommended Action
•
The client
connected to the
device cannot
access the
Internet.
•
•
•
•
The client cannot
access the
Internet in Internet
Wi-Fi mode.
•
Ensure that your (U)SIM card is
available.
Change the location and find a
place with good signal.
Check the settings of the WAN
connection mode.
Contact your service provider
and confirm your APN settings.
Ensure that the WLAN device
has already been connected to
the Internet.
Ensure that your device and the
WLAN device are in different
subnets.
22
Troubleshooting
Problem
Recommended Action
•
The 3G Mobile
Hotspot
configuration
page cannot
be visited.
•
•
Enter the correct address.
The default address is
http://192.168.0.1 or
http://m.home.
Use only one network adapter in
your PC.
Do not use any proxy server.
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising