ZTE | MF93D | User manual | ZTE MF93D User manual

ZTE MF93D User manual
WIRELESS BROADBAND MODEM
(Model MF93D)
Key Features:
•
•
•
•
•
•
•
•
•
Wi-Fi 802.11a/b/g/n
Support LTE FDD 2600MHz(Band 7) / 1800MHz(Band 3)
Absolute mobility across LTE/HSPA+/WCDMA/EDGE/GPRS networks
100Mbps download and 50Mbps upload capability
Multi-functional USB drive with Micro SD card slot up to 32GB
Able to connect simutaneously up to 10 devices
Able to connect to PCs, notebooks and other Wi-Fi devices
Battery capacity 2800mAh (min)
USB 2.0 for simple plug and play
Powered by:
WIRELESS
BROADBAND
MODEM
System Requirements:
Your personalised WiFi hotspot
• Windows XP, Vista, 7 & 8
• Mac OS X 10.4 and above
• Hardware system should meet the recommended
requirements for the installed OS version
• 24/7 Customer Service
• 1800 82 2000
• maxis.com.my/broadband(for self help tips)
Make sure your computer meets the requirements, or you might experience a dip in
performance from the residential gateway. For Windows XP, it is recommended that
you install patches Service Pack 2 and above. For Windows 2000, it is recommended
that you install patches Service Pack 4 and above.
MF93D
Open size: 200mm X 135mm H
Close size: 100mm X 135mm H
LEGAL INFORMATION
GETTING TO KNOW YOUR DEVICE
Copyright © 2013 ZTE CORPORATION.
Appearance
All rights reserved.
The following figure is only for your reference. The actual product may be different.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE Corporation.
1
4. Connect to the WLAN device.
There are two methods for your reference.
• Select the listed SSID, and then click Connect.
• Click Add, input the WLAN device information in the Add Wi-Fi Hotspot
area, and then click Apply.
2. Right-click Wireless Network Connection, and then select Properties.
2
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
3
4
5. After your device connected to the WLAN device successfully, you can access
the Internet.
CONFIGURING YOUR PC
3. Select Internet Protocol(TCP/IP), and then click Properties.
Follow the following steps and figures for Windows XP to configure the Internet
Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and then select Properties.
5
Version No. : R1.0
Edition Time : December 2012
NOTES:
Do not use the device in an enclosed environment or where heat dissipation is
poor. Prolonged work in such space may cause excessive heat and raise ambient
temperature, which may lead to automatic shutdown of the device for your safety.
In the case of such event, cool the device in a well-ventilated place before turning
on for normal use.
1. External Antenna
Connector
2. Micro USB Port
3. OLED Screen
6
7
4. Power Switch
5. (U)SIM Card Slot
6. RESET Button /
microSD Card Slot
7. WPS Button
NOTES:
* microSD logo
is a trademark of SD Card Association.
* Please use the original external antenna if necessary.
8
1
Indicators
When the device is powered on, the following icons will appear on the OLED
screen, with the corresponding indicates listed in the table below:
Iron
• Internet Wi-Fi Mode
Your device will connect to other WLAN
device (hotspot device, wireless router, etc.)
via Wi-Fi to access the Internet. The WLAN
device has already connected to the Internet.
NOTES:
The subnet must be deferent
between your device and
other WLAN device.
4. Select Obtain an IP address automatically and Obtain DNS server address
automatically, and then click OK to finish the configuration.
• Some electronic devices are susceptible to electromagnetic interference sent by
your device if inadequately shielded, such as the electronic system of vehicles.
Please consult the manufacturer of your device before using if necessary.
• Operating your device may interfere with medical devices like hearing aids and
pacemakers. Please always keep them more than 20 centimeters away from
such medical devices when they are turned on. Turn your device off if necessary.
Consulta physician or the manufacturer of the medical device before using
your device.
• The device complies with RF specifications when the device is used at 1cm from
your body.
• Be aware of the usage limitation when using your device at places such as oil
warehouses or chemical factories, where there are explosive gases or explosive
products being processed. Turn off your device if required.
• The use of electronic transmitting devices is forbidden in aircrafts, at petrol
stations and in hospitals. Please observe and obey all warning signs and switch
off your device in these conditions.
• Do not touch the inner antenna area if not necessary. Otherwise it will affect
your device’s performance.
• Store your device out of the reach of little children. Your device may cause injury
if used as a toy.
• Do not touch the metallic parts of your device so as to avoid a burn, when your
device is working.
Indication
Network type. 2G, 3G, 4G icon will appear on the
OLED screen according to the network being connected.
Connect to the Internet automatically.
Connect to the Internet manually.
Roaming network indication.
Installing Your Device
New message received.
Wi-Fi Status and number of the connected users.
1. Insert the SIM
Mcard.
card.
Battery power indication.
Connection Scenario
Your device supports two methods to go to Internet and supports multi-clients
for surfing on the Internet at the same time. The following figure is only for
your reference.
• 4G Mode
Use your (U)SIM card too
access the Internet.
Using Your Device
• The device is for indoor use only. Do not use the device outside. The device does
not support DFS.
• Please use original accessories or accessories that are authorized. Using any
unauthorized accessories may affect your device’s performance, and violate
related national regulations about telecom terminals.
• Avoid using your device near or inside metallic structures or establishments that
can emit electromagnetic waves. Otherwise it may influence signal reception.
• Your device is not waterproof. Please keep it dry and store in a shady and
cool place.
2. Insert the microSD card.
i) Open the microSD card cover.
NOTES:
Do not pull the cover rudely, as it is connected with the device.
2
ii) Insert the microSD card into the
microSD slot. The following picture
shows the correct inserting direction.
You will hear a click when the
microSD card locks in place.
3
3. Select the SSID of your device, and then click
only for your reference.
10
Connect. The following picture is
• Do not use your device immediately after a sudden temperature change. In such
case, it will produce dew inside and outside your device, so don’t use it until it
becomes dry.
• Handle your device carefully. Do not drop, bend or strike it. Otherwise your
device will be damaged.
• No dismantling by non-professionals and only qualified technicians can
undertake repair work.
• Operating temperature range of 0 °C ~+35 °C and humidity range of 5%~ 95%
are recommended.
3. Close the microSD card cover.
About your Adapter
CONNECTING TO YOUR DEVICE
•
•
•
•
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi
onon
the
client
to search
forfor
the available
Wi Fiapplication
application
the
client
search
availa
wirelesss networks.
networks.
Adapter shall be installed near the equipment and shall be easily accessible.
Model: ZTE MF93D
Manufacturer: ZTE Corporation
The plug considered as disconnect device of adapter.
Using Battery
4. Input the password, and then click Connect.
•
•
•
•
•
Do not short-circuit the battery, as this can cause excessive heat and fire.
Do not store the device in hot areas or dispose of it in a fire to avoid explosion.
Do not disassemble or modify the battery.
Never use any charger or battery damaged or worn out.
Return the wear-out battery to the provider or put it in the appointed recycle
place. Do not put it in familial rubbish.
WARNING:
Do not change the built-in rechargeable battery in your device by yourself.
The battery can only be changed by ZTE or ZTE authorized service provider.
Limited Warranty
NOTES:
Please set the client to obtain an IP address automatically referring to the chapter
“Configuring Your PC”, and then the client will get an IP address like
“192.168.0.100”.
NOTES:
* There may require the password for Wi-Fi connection, please check the label
on your device to get the default.
* Double press the WPS button, and then the SSID and Wi-Fi key will display on
the OLED screen.
4
5. Wait a moment, and then the client will connect to your device successfully.
• This warranty does not apply to defects or errors in the Product caused by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or maintenance
instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation,
disassembly, storage, servicing or operation of the Product.
5
ACCESSING THE INTERNET
4G Mode
12
Problem
Mode
Operations
Automatic
Your device will connect to the Internet automatically,
and your clients can surf on the Internet directly.
Manual
Login the webGUI configuration page, and select
Settings > Network Settings > Dial-up Settings >
Manual, and then click Home > Connect / Disconnect.
•
•
•
•
When I use Internet
Wi-Fi mode, the
client cannot access
the Internet.
• Make sure the other WLAN device has already
connected to the Internet.
• Make sure that the subnet of your device and the
other WLAN device is different
• Enter the correct address. The default address is
http://192.168.0.1 or http://m.home.
• Only use one network adapter in your PC.
• Do not use any proxy server.
About the password
• Press the WPS button twice, and then the SSID and
Wi-Fi connection password appear on the screen.
• The default password of the webGUI configuration
page is admin.
• If you changed the password and forgot the new
password, you need to restore the device to the
factory default settings.
About the device
• Press the reset button, the device will reset to the
default settings.
• If there is any exception while using the device,
please press and hold the Power Button for
about 10s, and the device will restart.
Internet Wi-Fi Mode
1. Login the webGUI configuration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network, and then click Apply.
2. Power on your device.
3. The OS detects and recognizes new hardware and finishes the installation
automatically.
NOTES:
You need to Enable the Internet Wi-Fi Switch and select Wi-Fi.
Make sure your (U)SIM card is available.
Change the location to find a place with good signal.
Check WAN Connection mode setting.
Contact with your service provider and confirm your
APN settings
Can not visit the
webGUI configuration
page
NOTES:
If you want to modify the detailed parameters of your device, please login the
webGUI configuration page by visiting http://192.168.0.1 or http://m.home. The
default password is admin.
1. Connect to the device.
Suggested Solution
The client connected
to the device can not
access the Internet
After the client connected to your device successfully, you can access the Internet in
the Automatic or Manual mode. The default mode is Automatic.
Via USB Cable
NOTES:
If the Windows operating system does not launch installation automatically, you can
run the installation program in path of My Computer > ZTEMODEM.
4. Wait a moment, and then the client will connect to your device successfully.
6
WARNING AND NOTICE
To the Owner
Network signal strength.
2G/3G/4G
9
7
14
11
iv. Modifications or repairs not made by ZTE or a ZTE-certified individual.
Power failures, surges, fire, flood, accidents, actions of third parties or other
events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with third-party
products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for the Product.
End User shall have no right to reject or return the Product, or receive a refund for
the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability for defective or
nonconforming items, and is in lieu of all other warranties, expressed, implied or
statutory, including but not limited to the implied warranties of merchantability
and fitness for a particular purpose, unless otherwise required under the
mandatory provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with using
of this product, whether or not ZTE had been advised, knew or should have known
of the possibility of such damages, including, but not limited to lost profits,
interruption of business, cost of capital, cost of substitute facilities or product, or
any downtime cost.
Troubleshooting
Problem
Suggested Solution
Can not establish
the USB connection
between your
device and PC
• You need to install the software. Run the installation
program in path of My Computer > ZTEMODEM.
• If the driver of your device is abnormal, please reinstall
the software. You need uninstall the software first.
Can not establish
the Wi-Fi connection
between your
device and client
• Make sure the Wi-Fi function is active. Press the WPS
button to enable
or disable
Wi-Fi function.
• Refresh network list and select the correct SSID.
• Check the IP address to make sure your client can
obtain an IP address automatically in the Internet
protocol (TCP/IP) properties.
• Type the correct network key (Wi-Fi password) when
you connect to the device.
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising