ZTE | MF60 | User manual | ZTE MF60 User manual

ZTE MF60 User manual
Introduction
MF60 Quick Guide
MF60 is a 3G/2G mobile hotspot device, working in GSM/GPRS/EDGE/
WCDMA/HSPA/HSPA+ network. The client devices could connect
to it via USB or Wi-Fi interface. The device supports data and SMS
services, enabling you to communicate anytime and anywhere.
This quick guide provides instructions on how to install and get started
with the product. For information about connection of services, please
consult your service provider.
Specification
Data Service
1
HSPA+: DL 21.6Mbps,
UL 5.76Mbps
WCDMA CS: 64kbps UL/DL
WCDMA PS: 384kbps UL/DL
Interface
USB and Wi-Fi
Wi-Fi Standard
802.11b/g
Wi-Fi Security
WEP/WPA/WPA2
USB Version
USB 2.0 HIGH SPEED
USB Interface Type
Micro USB
Weight
75g
Dimensions (W×H×D):
99.7mm*53.7mm*13.9mm
microSD card
Support up to 32GB microSD card
Power Adapter
5V/700mA
Battery
1500mAh
*Standby time
100hours
*Working time
4hours
2
Operate system
Windows 7, Windows Vista(32bit or 64bit),
Windows XP (SP2 or later), MAC (10.4 or
later)
Web Browser
IE (6.0 or later), Firefox (2.0 or later),
Opera (10.0 or later), Safari (4.0 or later),
Chrome (5.0 or later)
Operating temperature
0°C ~ +35°C
Storage temperature
-20°C ~ +50°C
Charging temperature
0°C ~ +45°C
Humidity
5%~ 95%
Interface and Buttons
LED Indicator
1. Power
Hold the Power button to switch on/off the
device.
When the device is powered on, the following icons will appear on the
LED screen, with the corresponding indicates listed in the table below:
2. Memory card slot
(microSD card)
It is where you insert the memory card
(microSD card).
3.WPS
This button is used to start/end Wi-Fi
Protected Setup authentication process and
enable/disable the Wi-Fi function.
• Hold it for 3 seconds to activate the WPS
function.
• When the WPS function is available,
press it to deactivate the WPS function.
• Press it to enable/disable Wi-Fi function.
Notes: microSD
is a trademark of SD Card Association.
The device’s standby and working time are only for your reference, and
based on ideal working environment.
4. LED Screen
Getting to Know Your Device
The following figure shows the appearance of the device, it is only for
your reference. The actual device may be different.
It indicates the signal type, signal strength,
battery, Wi-Fi, etc.
5. External Antenna
Connector
It is used to connect an external antenna to
enhance the signal strength.
6.Charger/USB port
• Charge your device.
• Connect the client to your device via USB
cable.
Notes:
Hold the WPS and Power buttons simultaneously until the LED
screen turns off, and then release the buttons. The device will restart
automatically and restore to the factory default settings.
Please use the original external antenna if necessary.
Right Side
Front
Left Side
3
2. Insert the SIM card into the SIM card holder.
Icon
Indication
3. Close the microSD cover.
Network signal strength.
Network type. 2G or 3G icon will appear on the LED
screen according to the network being connected.
3. Insert the battery as shown with the contacts located against the
metal springs, and press the battery down into the case.
Connect to the Internet automatically.
Roaming network indication.
New message received.
Wi-Fi Status and number of the connecting users.
Switching On/Off Your Device
Hold the Power button to switch on/off the device.
Notes:
The device is powered on when the LED screen lights up.
4. Line the battery cover up correctly and press gently to close the
case.
You can charge your device by using USB cable or adapter.
1. Insert the charger lead carefully.
2. The plug only fits one way. Do not use excessive force to insert the
plug.
Battery power indication.
Hardware Installation
Inserting SIM Card and Battery
1. Use the thumb catch at the bottom of the device to open the battery
cover.
5
Wi-Fi Mode: Connect to the device via Wi-Fi.
Charging Your Device
Connect to the Internet manually.
Bottom
4
Establish a connection between your device and
the client
Inserting microSD Card
1. Pull the microSD cover out of the card slot.
Notes:
Do not pull the cover rudely, as it is connected with the device.
2. Insert the microSD card into the microSD slot. The following picture
shows the correct inserting direction. You will hear a click when the
microSD card locks in place.
6
Working Mode
Mixed Mode: Connect to the device with the above two connection
methods.
Notes:
If you want to connect to the Internet by using Wi-Fi mode, make sure
that the client supports the Wi-Fi function.
The following picture is the application example. All of the client devices
can surf on the Internet at the same time.
Via USB Cable
1. Connect your device and the client with the USB cable.
2. Power on your device.
3. Follow the system prompts to complete the software installation.
Notes:
• If the system does not launch installation automatically, you can run
the installation program in path of My Computer > Ncell Connect.
• The driver of your device will be installed at the same time.
4. After the installation, the system will create a shortcut icon
on your desktop and a Ncell Connect program group in the
Start→Programs menu. The connection between your device and
the client will be established successfully a moment later.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search the
available wireless network.
Notes: You need to check your Wireless Network Connection. Set the
client to obtain an IP address automatically in the Internet protocol (TCP/
IP) properties, and the client will get an IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click Connect. The
following figure is for your reference only.
Your device supports three working modes. For the client, we only use
PC or laptop as the example in this document.
USB Mode: Connect to the device with the USB cable.
7
8
9
Access the WebGUI Configuration Page
1. Make sure the connection between your device and the client is
correct.
2 Launch the internet browser and enter http://192.168.0.1 or http://
ufi.home in the address bar.
Notes: It is recommended that you use IE (6.0 or later), Firefox (2.0 or
later), Opera (10.0 or later), Safari (4.0 or later), Chrome (5.0 or later).
3. The login page appears as follows. The following figure is only for
your reference.
Quick Settings
Settings
If the PIN code of your SIM card is enabled, you will need to input the
PIN code when you login at the first time.
After logging in, select Quick Settings, and then the wizard appears.
After logging in, select Settings, and you can do the following
operations.
Notes:
The SIM card will be locked if you enter wrong PIN code consecutively
for three times.
If you want to modify the PIN Status, please select Settings >
Advanced > PIN Management to do the actions.
Notes:
There will be a pop-up window to require the password. Check the
label on your device to gain the SSID and preset password information.
Please do remember the new password when you change the
password by selecting Settings > Wi-Fi Settings > Security after
logging in the WebGUI Configuration Page. You can restore the device
to the factory default settings in case you forget it.
4. Wait a moment, the connection between your device and the client
will be established successfully.
Access the Internet
PIN Code Verification
The wizard guides you how to set the basic parameters for your device
in the safest way. After this procedure, you can use your Internet
service.
Notes: The parameter settings may have been preset by your service
provider, and you will enjoy your Internet service directly. Please contact
your service provider for details if you want to do some modification.
WAN Connection
After logging in, select WAN Connection, and you can choose the
WAN Connection Mode according to your requirement.
1. Switch on the device.
2. Establish a connection between your device and the client.
3. After successfully establishing the connection, access the Internet
in the Always On or Manual mode.
Notes:
You can browse the WebGUI Configuration page and click WAN
Connection to set the WAN connection mode.
View the information of WAN, WLAN and Device. Input the casesensitive default password “admin”, and then click Login to access the
WebGUI Configuration page.
Notes:
• Do not put anything on the top of your device. Do not lay devices to
overlap each other when using.
• The device takes 1~2 minutes to initialize, and attach to the
network.
10
11
Select Settings View the 3G Wireless Information, select Band
> 3G Settings Selection Mode or change APN Setting.
View the current station list, change the basic
Select Settings
wireless network settings, choose security mode
> Wi-Fi Settings
and WPA type, and perform the WPS configuration.
Select Settings Set the MAC/IP/Port Filtering, Port Forwarding or
> Firewall
the System Security configuration.
View the current status of your device, change the
Select Settings
Administrator Settings, restore factory defaults,
> Advanced
manage PIN or set the LAN interface configuration.
Notes:
Make sure that you can remember the new password if you change the
login password by selecting Settings > Advanced > Management.
Please restore the device to the factory default settings in case you
forget the new password.
Disconnect from the Internet
1. Log in the WebGUI Configuration page, and select WAN
Connection.
2. Select Manual > Disconnect Internet.
3. Click Apply.
Usage of WPS
Notes:Turning off the device can also terminate the internet connection.
SMS
This function allows you to view, send and receive short messages.
After logging in, select SMS, and you can do the following operations.
Select SMS > Device
Select SMS > SIM Card
Select SMS > New Message
Select SMS > SMS Settings
Operate the SMS in your device.
Operate the SMS in your SIM card.
Send or save SMS.
Set the SMS configuration.
PhoneBook
This function allows you to store contacts to your device or SIM card.
After logging in, select PhoneBook, and you can add a new contact in
Add New tab, and perform operations to the contact in the Device or
SIM Card tab.
If your client device supports WPS, you need not to input the password
manually after WPS has been available. Please do the following:
1. Start up your device.
2. Launch the client device connected to your device.
3. Enable the WPS function of your device.
4. Enable the WPS function of the client.
Notes:
• If the current security mode of the device is OPEN or SHARE, the
WPS function is useless.
• For the detailed operations about the client, please refer to the
client’s instruction.
Sleep Mode
When you enable the Wi-Fi function and use the battery to supply
power to the device, once no user connects to the device within 10
minutes or you press the WPS button, the device will enter the sleep
mode, and the LED screen will be turned off. In the sleep mode, the
Wi-Fi function will be disabled. Press Power or WPS button to wake up
the device, and the LED screen will be turned on.
Notes:
With USB connection if no Wi-Fi user connects to the device within 10
minutes, only the Wi-Fi function will be disabled. Hold the WPS button
about 3 seconds to enable this function.
•
•
•
•
•
•
Using Your Device
•
Warning and Notice
•
To the Owner
•
12
13
14
15
Some electronic devices are susceptible to electromagnetic
16
interference sent by your device if inadequately shielded, such as
the electronic system of vehicles. Please consult the manufacturer
of your device before using if necessary.
Operating of laptop and desktop PCs and your device may interfere
with medical devices like hearing aids and pacemakers. Please
always keep them more than 20 centimeters away from such
medical devices when they are turned on. Turn your device off if
necessary. Consult a physician or the manufacturer of the medical
device before using your device.
Be aware of the usage limitation when using your device at places
such as oil warehouses or chemical factories, where there are
explosive gases or explosive products being processed. Turn off
your device if required.
The use of electronic transmitting devices is forbidden in aircrafts,
at petrol stations and in hospitals. Please observe and obey all
warning signs and switch off your device in these conditions.
Do not touch the inner antenna area if not necessary. Otherwise it
will affect your device’s performance.
Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Please use original accessories or accessories that are authorized.
Using any unauthorized accessories may affect your device’s
performance, and violate related national regulations about telecom
terminals.
Avoid using your device near or inside metallic structures or
establishments that can emit electromagnetic waves. Otherwise it
17
•
•
•
•
•
may influence signal reception.
Your device is not waterproof. Please keep it dry and store in a
shady and cool place.
Do not use your device immediately after a sudden temperature
change. In such case, it will produce dew inside and outside your
device, so don’t use it until it becomes dry.
Handle your device carefully. Do not drop, bend or strike it.
Otherwise your device will be damaged.
No dismantling by non-professionals and only qualified technicians
can undertake repair work.
Operating temperature range of 0°C ~ +35°C and humidity range of
5% ~ 95% are recommended.
Using Battery
•
Do not short-circuit the battery, as this can cause excessive heat
and fire.
• Do not store battery in hot areas or dispose of it in a fire to avoid
explosion.
• Do not disassemble or modify the battery.
• When not using the battery for a long period, remove it from your
device and store it in a cool dry place.
• Never use any charger or battery damaged or worn out.
• Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
Warning:
If the battery is broken, keep away from it. If it taints your skin, wash
your skin with abundant fresh water and ask doctor help if necessary.
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising