ZTE | F116 | User manual | ZTE F116 User manual

ZTE F116 User manual
Phone Overview
3.
Hold your (U)SIM card with the cut corner oriented as shown above the
(U)SIM card slot and then slide it into the slot.
Charging Your Phone
Indicator Icons
Please charge your phone before initial use. The plug and socket are keyed so
they will only fit together one way.
Shortcut for Menu
•
Service Provider or
Status of the Phone
Text Input
In the main menu, press the corresponding Alphanumeric Key as shown on
the menu below to access the corresponding menu.
1.
2.
3.
4.
Default Menus
ZTE F116
Quick Start Guide
4.
You can always return to the standby mode by pressing the End Key.
Slip the memory card carefully into the microSD card slot with the metal
contacts facing downwards.
Indicators and Icons
•
Signal strength
Powering On/Off
LEGAL INFORMATION
Copyright © 2012 ZTE CORPORATION.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in
any form or by any means, electronic or mechanical, including photocopying and
microfilm, without the prior written permission of ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to make
modifications on print errors or update specifications without prior notice.
Version No. : 1.0
Edition Time: 04 09, 2012
Manual No. : 079584504464
Installing the (U)SIM, Memory Card and Battery
1.
2.
Make sure that the phone is powered off and the charger is disconnected
from the phone.
Turn the phone over, hook the edge of the back cover and lift it up to remove
the back cover.
1. Hold the End Key to power on the phone.
Note:
When being asked, enter your PIN code or handset code, and press the OK Key
to confirm.
2. To power off the phone, hold the End Key from the standby mode.
Note:
is a trademark of SD Card Association.
The microSD logo
5. Insert the battery by aligning the gold contacts on the battery with the gold
contacts in the battery compartment on the phone.
F116 QSG (Solomon_EN)V1.0-120413.indd
•
In the standby mode, hold the * Key to lock your phone.
In the main menu, select Settings > Phone > Auto keyguard and set the
desired time to lock the phone.
If you want to unlock your phone, press the OK Key, and then press the
* Key.
Standby Mode
3
4
5.
6.
Battery status
Bluetooth on
Data transfer in attaching
New SMS
7.
8.
Data transfer in progress
New MMS
9.
Silent mode
Missed voice call
Meeting mode
Missed video call
Searching the Contact
Voice Call
1.
2.
In the standby mode, enter the phone number.
Press the Send Key to make a voice call.
Video Call
Headset inserted
1.
2.
The startup screen below is referred to throughout the guide as the standby
mode.
2
1
•
•
Tip:
If the call is coming when the phone is locked, please press the Send Key to
answer. After ending or rejecting the call, the keypad will be locked automatically.
ZTE CORPORATION
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Tel: +86-755-26779999
Website: http://www.zte.com.cn
E-mail: mobile@zte.com.cn
1
Lock/Unlock Your Phone
Alarm on
Press the corresponding Alphanumeric Key as shown before one option to
quickly access the corresponding function.
5
Sending SMS
Change input mode: Press # Key to choose input mode from the drop-down
menu.
Change input language: Press # Key and choose the last option from the
drop-down menu. Then select the language you need and press OK Key.
Input Letters: In abc/Abc/ABC mode, press the corresponding letter key till
the letter appears.
Input Words: In En mode, key-in any letter with a single key pressing. Press
each key only once for every letter. The phone will present a list of words
based on the keys you pressed and its built-in dictionary. The word changes
after each key stroke. When you have finished typing, move the cursor with
Navigation Keys to choose the right word and confirm it by pressing 0 or
OK Key.
Input Digits: In 123 mode, press a digit key once to enter a digit. In eZiEng
mode, press the digit key, and select the number by pressing a Navigation
key. In abc/Abc/ABC mode, constantly press the digit key until the number
appears.
Input Symbols: Press * Key to choose a symbol and OK Key to insert it into
the text. In abc/Abc/ABC mode, press 1 Key continuously till the required
symbol (common symbols) appears.
Input Space: Press 0 Key to input space. It does not work in 123 mode.
Delete Characters: Press Clear Key to clear a character. Press and hold
Clear Key to delete all text before the cursor.
Move Cursor: Press Navigation Keys to move the cursor left, right, up, or
down.
In the Contacts interface, enter the first letter of the name you are searching for.
Such as ‘John’, press the 5 Key once for ‘J’. All the names starting with ‘J’ are
displayed.
Tip:
Refine the search by entering more letters that can occur anywhere in the name.
In the standby mode, enter a phone number
Select Options > Call > Video call to make a video call.
6
2.
Setting SMS
1. In standby mode, select Menu > Messages> Settings > Text Msg.
Settings.
2. Set the related parameters. For more details, please contact your service
provider.
3. Press the OK Key to complete.
Sending SMS
1. In standby mode, select Menu > Messages > Create message.
2. Enter the phone number(s) of the recipient(s). You can also select Recipient
to add the receiver(s).
3. Press the Down Key to enter the Text field and edit the text.
4. Press the OK Key to send the SMS.
You can edit or create the mailbox. For the details, please ask your mail
service provider.
3. Press the OK Key to save your settings.
Sending E-mail
1. In standby mode, select Menu > Messages, press the Right Key to enter
the Email interface, and then select New Email.
2. Enter the recipient’(s’) Email address. You can also press the OK Key to add
the receiver(s) from the Contacts.
3. Press the Down Key to access CC field and enter the Email address of
recipient(s).
4. Press the Down Key to edit the title.
5. Press the Down Key to access the Text field.
6. Edit the contents.
7. Press the OK Key to send the Email.
Sending MMS
Setting Network Connection
Setting MMS
1. In standby mode, select Menu > Messages > Settings > Mul. Msg.
Settings.
2. Set the related parameters. For more details, please contact your service
provider.
3. Press the OK Key to complete.
Sending MMS
1. In standby mode, select Menu > Messages > Create message.
2. Enter the phone number(s) of the recipient(s). You can also select Recipient
to add the receiver(s).
3. Press the Down Key to enter the Text field and edit the text.
4. Select Options > Insert > Sub to edit the title.
5. Select Options > Insert to add the attachments (image, audio or video, etc.).
6. Press the OK Key to send the MMS.
Checking and creating APN
Sending an E-mail
Note:
If there is no desired APN in the Access point settings menu, select Options >
Add to create a new APN profile.
Setting the connection
1. In standby mode, select Menu > Settings > Connections > Profile connect
2. Press Add to create a new connection profile. Enter the necessary
information and select the proper APN.
Setting Mailbox
1. In standby mode, select Menu > Messages, press the Right Key to enter
the Email interface, and then select Settings > Mailbox Settings.
7
8
9
2012-4-16
16:33:04
Viewing the Pictures
Feature
3.
Press Save to finish.
Activating the Proper Connection
Network settings: Configure the network settings.
Function Key
Full Scn.
OK Key
Zoom in or out
Up o Down Key
Rotate the image
1,3 Keys
Enjoying the Video
Volume up and down
Left and Right Keys
Brightness
2,8 Keys
New URL: Create a new streaming URL.
2. Find the file which you want to send.
Note: Select Search For New Device to scan the available device(s).
3. Select the destination device, and follow the prompts to finish procedure.
10
F116 QSG (Solomon_EN)V1.0-120413.indd
2
If you activate data service function, your phone will be used as a modem. And
the following steps are only for reference.
1. Choose USB connection mode.
Edit: Modify the selected URL.
Send: Send the selected URL via Message or Email.
Delete: Delete the selected URL.
11
Dimensions (L×W×H)
Weight
Display
Back camera
Extended memory
Battery
Continuous idle time
Continuous talk time
Continuous video talk time
Charge time
•
110 mm×47.5 mm×11.8 mm
Approx 70 g (including battery)
2.0 inches 176*220 TFT
0.3 M pixel camera
32 G microSD card
820 mAh, Lithium ion (Li-ion)
GSM: 200 hours; WCDMA: 330 hours
GSM: 240 minutes; WCDMA: 400 minutes
135 minutes
Approx 3 to 4 hours
Note:
The phone’s talk time and idle time are based on ideal working environments.
The use of extended backlighting, browser, and network conditions can reduce
battery life and talk/idle time.
2.
In standby mode, select Menu > Multimedia > Video > Streaming URL to enter
the streaming interface.
TV channels are links to audio or video streaming content that are available
through the browser (similar to bookmarks). The streaming content is only
available while you are connected to the server, depending on your service
provider or available content.
1. If there is no Streaming URL list, press Add to add a new streaming file,
input the Title and URL and then press the OK Key to save.
2. In the Streaming URL list interface, press Open to open the URL, press
Options for more options:
Enable the Bluetooth function.
Using the Phone as Modem
Function Key
Streaming
1.
Info.: View the information about the selected URL.
Additional features when you view one video:
Feature
Using Bluetooth
Technical Parameters
Delete all: Delete all the URLs.
Additional features when you view one picture:
Select Menu > Settings > Connections > Modem settings to set the
related parameters, and then press OK to save your configuration.
Safety Information
General Care
Note:
For the detail settings, please consult your service provider.
3. Install and launch Join Me application software, and then click Connect to
establish the connection between your phone and the software.
4. Click Network.
5. Click the Connect button to access to the Internet.
12
Your handset contains delicate electronic circuitry, magnets and battery systems.
You should treat it with care and give particular attention to the following points:
•
Do not allow the handset, battery or accessories to come into contact with
liquids or moisture at any time. Do not immerse the handset in any liquid.
•
Do not place the handset alongside computer disks, credit cards, travel cards
and other magnetic media. The information contained on disks or cards may
be affected by the handset.
•
Do not paint the handset.
•
Do not leave the handset or the battery in places where the temperature
could exceed 60 °C, e.g. on a car dashboard or a windowsill, behind glass in
direct sunlight, etc.
•
Do not remove the handset’s battery while the handset is switched on.
•
Take care not to allow metal objects, such as coins or key rings to contact or
short-circuit the battery terminals.
13
Do not dispose of battery in a fire. The handset’s Li-ION batteries may be
safely disposed of at a Li-ION recycling point. Follow local requirements for
recycling.
•
Do not put the handset’s battery in your mouth, as battery electrolytes may
be poisonous if swallowed.
•
Do not attempt to dismantle the handset or any of its accessories.
•
Do not put a battery into a microwave oven, dryer, or high-pressure
container.
•
Do not contact battery directly to an electric outlet or cigarette lighter charger.
Use only approved charger units.
•
Do not pierce battery with a sharp object such as a needle.
•
Do not disassemble or modify the battery.
•
Do not use a damaged or deformed battery.
•
Do not drop, throw, or subject the handset to rough treatment.
•
Do not solder the battery directly.
•
Stop using the battery if abnormal heat, odor, discoloration, deformation, or
abnormal condition is detected during use, charge, or storage.
•
Remove the battery whose life cycle has expired from equipment
immediately.
•
This equipment is fitted with an internal battery. Take it to a qualified service
engineer when the replacement of the battery is required.
•
The earpiece may become warm during normal use. Also, the handset itself
may become warm while the battery is being charged.
•
When a handset is in vibration mode, the vibration can sometimes cause the
handset to move.
•
Be careful not to place the handset near heat sources (such as a heater) or
too close to the edge of the table.
•
Power off your phone before you clean it. Use a damp or anti-static cloth to
clean the handset. Do not use an ordinary dry cloth or electrostatic cloth. Do
not use chemical or abrasive cleaners as these could damage the casing.
•
Remember to make backup copies of all important data on your handset.
•
Remember to recycle: the cardboard packing supplied with this handset is
ideal for recycling.
Warning: In the unlikely event of a battery leak, take care to keep the battery
discharge away from your eyes or skin. If the leakage does come into contact
with the eyes or skin, please flush thoroughly in clean water and consult with a
doctor.
14
General Guidelines
•
•
•
•
•
•
•
•
•
•
•
•
•
•
In some countries, national law prohibits private copying of copyrighted
material. Please check the national legislation of the applicable country
concerning the use of such material.
Many jurisdictions have laws and regulations about taking pictures in public
or private areas and regarding the processing and further use of such
pictures. The manufacturer encourages its customers to obey all laws and to
respect the personal rights of others.
Please check roaming agreement availability with your service provider.
The use of mobile phones is not allowed in some radiation sensitive areas,
such as hospitals, research centers and airplanes. The user is responsible
to power-off the device. If there is any uncertainty, you should remove the
battery from the handset.
Observe any signs that indicate powering off handsets, such as those near
gas stations, or explosives, and power off the handset/device immediately.
If you have a heart condition, be careful with the settings of call vibration or
tone volume.
Do not allow children to play with the handset, charger or batteries.
Do not use the handset where blasting is in progress.
Do not try to make a call or conversation while the temperature of charging
battery is above 50°C.
Take care not to put your handset in the back pocket of your trousers or skirt
and then sit on it. Also, do not put your phone at the bottom of bag where
it may subject to excessive weight or pressure. Doing so may damage the
LCD and camera lens and cause them malfunction.
The operation of some medical electronic devices, such as hearing aids and
pacemakers, may be affected if a handset is used next to them. Observe any
caution signs and the manufacturer’s recommendations.
Do not leave the handset discharged or without a battery for a long time,
otherwise some data may be erased.
Your phone contains metal, which may cause you an itch, a rash or eczema
depending on your physical condition.
Road Safety
•
You must exercise proper control of your vehicle at all times. Give your full
attention to driving.
15
•
•
•
•
•
Observe all of the recommendations contained in your local traffic safety
documentation.
Pull off the road and park before making or answering a call, if driving
conditions require so. Check if local laws and/or regulations restrict the use
of handsets while driving
You must not stop on the hard shoulder of a motorway to answer or make a
call, except in an emergency.
Power off your handset at a refueling point, such as a gas station, even if
you are not refueling your own car.
Do not store or carry flammable or explosive materials in the same
compartment as the handset.
Electronic systems in vehicle, such as anti-lock brakes, speed control and
fuel injection systems are not normally affected by radio transmissions.
The manufacturer of such equipment can advise if it is adequately shielded
from radio transmissions. If you suspect vehicle problems caused by radio
transmissions, consult your dealer and do not power on the handset until it
has been checked by a qualified technician.
Hospital Safety
•
•
Notes:
•
Tell the operator which service you require: Police, Ambulance, Fire Brigade,
Coastguard or Mountain Rescue Service. Tell them where you are and
remain stationary to maintain contact if possible.
•
Due to the nature of the cellular system, the connection of emergency calls
cannot be guaranteed. You should never rely solely on any wireless device
for essential communications like medical emergencies.
Third Party Equipment
Emergency Service
To make an emergency call in any country:
1. Ensure that your handset is on and in service.
2. Press the End Key as many times as needed to clear the display and ready
the device for calls.
3. Enter the official emergency number for your present location, for example,
112 (the international emergency number).
4. Press the Send Key to dial the number. Follow instructions received and do
not end the call until told to do so.
When the (U)SIM card is not inserted, press SOS and then enter the official
emergency number for your present location. Press the Send Key to dial the
number.
16
An airbag inflates with great force. Do not place objects, including either installed
or portable wireless equipment, in the area over the airbag or in the airbag
deployment area. If in-vehicle wireless equipment is improperly installed and the
airbag inflates, serious injury could result.
Aircraft Safety
•
The use of third party equipment, cables or accessories, not made or authorized
by ZTE, may invalidate the warranty of your handset and also adversely affect
the phone’s safety/operation.
Radio Frequency (RF) Energy
•
Your handset is a low-power radio transmitter and receiver. When powered on, it
intermittently receives and transmits radio frequency (RF) energy (radio waves).
The transmit power level is optimized for the best performance, and automatically
reduces in the areas with better reception.
Exposure to radio frequency energy
Power off your phone and remove the battery in areas where the use of
handsets is prohibited.
Follow the instructions given by the respective medical facility regarding the
use of handsets on their premises.
Vehicles Equipped with an Airbag
Radio wave exposure and Specific Absorption Rate (SAR) information:
•
The handset is designed to comply with safely, requirements for exposure to
radio waves. This requirement is based on scientific guidelines that include
safety margins designed to assure the safety of all persons, regardless of
age and health.
•
The radio wave exposure guidelines employ a unit of measurement known
as the Specific Absorption Rate, or SAR. Tests for SAR are conducted using
a standardized method with the phone transmitting at its highest certified
power level in all used frequency bands.
•
While there may be differences between the SAR levels of various ZTE
phone models, they are all designed to meet the relevant guidelines for
exposure to radio waves.
•
The SAR limit recommended by the International Commission on NonIonizing Radiation Protection (ICNIRP) is 2.0 W/kg averaged over ten (10)
grams of tissue.
•
The highest SAR value for this model phone tested for use at the ear is 0.935
W/kg (10g).
17
Power off your phone before the airplane takes off. In order to protect
airplane’s communication system from interference, it is prohibited to
use mobile phone in flight. If you want to use mobile phone before the
airplane takes off, you should get aircrew’s permission according to safety
regulations.
If the mobile phone has the function of automatic timing power-on, please
check your alarm setting to ensure that your phone will not be automatically
powered on during the flight.
Privacy Information
Camera usage and photo/audio/video recordings carried out with the handset
can offend the confidentiality of the subjects. The user therefore is held to respect
legislation in confidentiality matter and remains the only responsible subject in
case of eventual violations of the enforced norm.
Copyright Notice
The video/audio recordings you make/download are protected by copyright laws.
They are for personal use only and must not be otherwise used without the
permission of the copyright owner.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or
consequential damages resulting from or arising out of or in connection with
using this product, whether or not ZTE has been advised, knew or should have
known the possibility of such damages. Refer to the enclosed warranty card for
full warranty and service information.
18
2012-4-16
16:33:06
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising