ZTE | MF65 | User manual | ZTE MF65 User manual

ZTE MF65 User manual
Let’s go
Getting started with your device.
Getting to Know Your Device
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
The following figure is only for your reference. The actual product may be
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without the prior written permission of ZTE
The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without prior
Version No. : R1.0
Edition Time : 2014.01
LED Indicators
WPS Button
(U)SIM Card Slot
NOTE: microSDHC logo
Power Button
Micro USB Port
microSDHC Card Slot
is a trademark of SD-3C, LLC.
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat
and raise ambient temperature, which may lead to automatic shutdown
of the device for your safety. In the case of such event, cool the device in
a well-ventilated place before turning on for normal use.
Red solid
Error status. Not registered to the mobile
network, no (U)SIM card inserted or no
network service available.
Green solid
Registered to the mobile network.
Connected to the mobile network and data
is being transferred.
Blue solid
Wi-Fi is active.
Installing Your Device
Blue blinking
WPS is active.
LED light off
Wi-Fi is off or your device is in sleep mode.
Red solid/
The battery is low. Please charge the battery.
The battery is being charged.
Green solid
The battery level is middle or high.
LED light off
Your device is in standby mode and not being charged, or the battery is not inserted.
Insert the microSDHC card if necessary.
Connecting to Your Device
Input the password, and then click Connect.
Via Wi-Fi
Slide the back cover and remove it
Follow the following steps and figures for PC to connect to your device.
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the
available wireless networks.
NOTE: You may need to input the password for Wi-Fi connection. Please
check the label on your device to get the default.
5. Wait a moment, and then the client will connect to your device successfully.
Remove the battery.
Insert the battery.
Connection Scenario
Your device allows to use your (U)SIM card to access the Internet and
supports multi-clients for surfing on the Internet at the same time. The
following figure is only for your reference.
3. Insert the (U)SIM card.
Your device does not support Micro/Nano or any other nonstandard SIM
cards. To avoid device damage, please do not use them.
Close the back cover.
NOTE: Please set the client to obtain an IP address automatically referring to the chapter “Configuring your PC”, and then the client will get an
IP address like “”.
3. Select the SSID of your device, and then click Connect.
Via USB Cable
NOTE: Please check the label on your device to get the default SSID.
Connect to the device.
Power on your device.
The OS detects and recognizes new hardware and finishes the installation automatically.
NOTE: If the system does not launch installation automatically, you can
run the installation program in path of My Computer > Sun Broadband.
4. Wait a moment, and then the client will connect to your device successfully.
Configuring Your PC
Select Internet Protocol(TCP/IP), and then click Properties.
Follow the following steps and figures for Windows XP to configure the
Internet Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and then select Properties.
Warning and Notice
To the Owner
Accessing the Internet
After the client connected to your device successfully, you can access
the Internet in the Automatic or Manual mode. The default mode is Automatic.
Your device will connect to the Internet automatically,
and your clients can surf on the Internet directly.
Log in the webGUI configuration page.
Select Settings > Network Settings > Dial-up
Settings > WAN Connection Mode > Manual, and
then click Apply.
Select Home, and then click Connect or Disconnect.
If you want to modify the detailed parameters of your device, please log
in the webGUI configuration page by visiting or http://
ufi.home. The default password is admin.
Right-click Wireless Network Connection, and then select Properties.
Select Obtain an IP address automatically and Obtain DNS server address automatically, and then click OK to finish the configuration.
Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded, such as the electronic system of vehicles. Please consult the manufacturer of your
device before using if necessary.
Operating your device may interfere with medical devices like hearing aids and pacemakers. Please always keep them more than 20
centimeters away from such medical devices when they are turned
on. Turn your device off if necessary. Consult a physician or the
manufacturer of the medical device before using your device.
Be aware of the usage limitation when using your device at places
such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Turn off your
device if required.
The use of electronic transmitting devices is forbidden in aircrafts, at
petrol stations and in hospitals. Please observe and obey all warning
signs and switch off your device in these conditions.
Do not touch the inner antenna area if not necessary. Otherwise it
will affect your device’s performance.
Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Using Your Device
Please use original accessories or accessories that are authorized.
Using any unauthorized accessories may affect your device’s perfor-
mance, and violate related national regulations about telecom terminals.
Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves. Otherwise it may
influence signal reception.
Your device is not waterproof. Please keep it dry and store in a
shady and cool place.
Do not use your device immediately after a sudden temperature
change. In such case, it will produce dew inside and outside your
device, so don’t use it until it becomes dry.
Handle your device carefully. Do not drop, bend or strike it. Otherwise your device will be damaged.
No dismantling by non-professionals and only qualified technicians
can undertake repair work.
Operating temperature range of 0°C ~ +35°C and humidity range of
5% ~ 95% are recommended.
Using Battery
Do not short-circuit the battery, as this can cause excessive heat and
Do not store battery in hot areas or dispose of it in a fire to avoid explosion.
Do not disassemble or modify the battery.
When not using the battery for a long period, remove it from your
device and store it in a cool dry place.
Never use any charger or battery damaged or worn out.
Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
WARNING: If the battery is broken, keep away from it. If it taints your skin,
wash your skin with abundant fresh water and ask doctor help if necessary.
Limited Warranty
This warranty does not apply to defects or errors in the Product
caused by:
Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or maintenance instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified individual.
v. Power failures, surges, fire, flood, accidents, actions of third
parties or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with thirdparty products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for
the Product.
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
This warranty is End User’s sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of the law.
Limitation of Liability
ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, whether or not ZTE had been advised,
knew or should have known of the possibility of such damages, including,
but not limited to lost profits, interruption of business, cost of capital, cost
of substitute facilities or product, or any downtime cost.
Suggested Solution
Can not establish
the USB connection
between your device
and PC.
Can not establish
the Wi-Fi connection
between your device
and client.
You need to install the software. Run the installation program in path of My Computer
> Sun Broadband.
If the driver of your device is abnormal,
please reinstall the software. You need to
uninstall the software first.
Make sure the Wi-Fi function is active.
Refresh network list and select the correct
Check the IP address to make sure your client can obtain an IP address automatically
in the Internet protocol (TCP/IP) properties.
Type the correct network key (Wi-Fi password) when you connect to the device.
The client connected
to the device can not
access the Internet.
Can not visit the webGUI configuration
About the password
Make sure your (U)SIM card is available.
Change the location to find a place with
good signal.
Check WAN Connection mode setting.
Contact with your service provider and confirm your APN settings.
Enter the correct address. The default address is or http://ufi.home.
Only use one network adapter in your PC.
Do not use any proxy server.
For the Wi-Fi connection password, please
check the label on the device.
The default password of the webGUI configuration page is admin.
If you changed the password and forgot the
new password, you need to restore the device to the factory default settings.
For more assistance, please:
Send E-mail to mobile@zte.com.cn
Visit http://www.ztedevice.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF