ZTE | MF93D | User manual | ZTE MF93D User manual

ZTE MF93D User manual
LEGAL INFORMATION
Getting to Know Your Device
Copyright © 2014 ZTE CORPORATION.
MF93D
Let’s go
Getting started with your device.
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without the prior written permission of
ZTE Corporation.
The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without prior
notice.
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
1
Appearance
Connect to the Internet manually.
The following figure is only for your reference. The actual product may
be different.
External Antenna Connector
Micro USB Port
OLED Screen
Power Switch
(U)SIM Card Slot
RESET Button / microSDHC™ Card Slot
 WPS Button
NOTES:
• microSDHC logo
is a trademark of SD-3C, LLC.
• Please use the original external antenna if necessary.






Internet. The WLAN device has already connected to the Internet.
NOTE:
The subnet must be deferent between your device and other WLAN
device.
Roaming network indication.
NOTE:
Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive
heat and raise ambient temperature, which may lead to automatic shutdown of the device for your safety. In the case of such event, cool the
device in a well-ventilated place before turning on for normal use.
2
3
After the client connected to your device successfully, you can access
the Internet in the Automatic or Manual mode. The default mode is
Automatic.
Mode
Via USB Cable
1. Connect to the device.
Connection Scenario
Installing Your Device
Your device supports two methods to go to Internet and supports multiclients for surfing on the Internet at the same time. The following figure
is only for your reference.
• 4G Mode: Use your (U)SIM card to access the Internet.
1. Insert the SIM card.
3) Close the microSDHC card cover.
Connecting to Your Device
•
Internet Wi-Fi Mode: Your device will connect to other WLAN device (hotspot device, wireless router, etc.) via Wi-Fi to access the
4
4. Input the password, and then click Connect.
Via Wi-Fi
1. Power on your device directly. It will take 1~2 minutes to initialize.
2. Use your normal Wi-Fi application on the client to search for the
available wireless networks.
NOTE:
• There may require the password for Wi-Fi connection, please check
the label on your device to get the default.
• Double press the WPS button, and then the SSID and Wi-Fi key
will display on the OLED screen.
5. Wait a moment, and then the client will connect to your device successfully.
IMPORTANT: Your device does not support Micro/Nano or any other
nonstandard SIM cards. To avoid device damage, please do not use
them.
Indication
Network type. 2G, 3G, 4G icon will appear on the OLED
screen according to the network being connected.
4G Mode
2. Insert the microSDHC card.
1) Open the microSDHC card cover.
5
6
7
2. Power on your device.
3. The OS detects and recognizes new hardware and finishes the installation automatically.
NOTE: If the Windows operating system does not launch installation
automatically, you can run the installation program in path of My Computer > ZTEMODEM.
4. Wait a moment, and then the client will connect to your device successfully.
8
Operations
Automatic
Your device will connect to the Internet automatically,
and your clients can surf on the Internet directly.
Manual
Login the webGUI configuration page, and select Settings > Network Settings > Dial-up Settings > Manual, and then click Home > Connect / Disconnect.
Battery power indication.
Network signal strength.
2G/3G/4G
Accessing the Internet
NOTE: Please set the client to obtain an IP address automatically referring to the chapter “Configuring Your PC”, and then the client will get an
IP address like “192.168.0.100”.
3. Select the SSID of your device, and then click Connect. The following picture is only for your reference.
Wi-Fi Status and number of the connected users.
When the device is powered on, the following icons will appear on the
OLED screen, with the corresponding indicates listed in the table below:
Icon
NOTE:
Do not pull the cover rudely, as it is connected with the device.
2) Insert the microSDHC card into the microSDHC slot. The following
picture shows the correct inserting direction. You will hear a click
when the microSDHC card locks in place.
New message received.
Indicators
Version No. : R1.0
Edition Time : 2014.05
ZTE CORPORATION
Connect to the Internet automatically.
NOTE:
If you want to modify the detailed parameters of your device, please
login the webGUI configuration page by visiting http://192.168.0.1 or
http://m.home. The default password is admin.
Internet Wi-Fi Mode
1. Login the webGUI configuration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network, and then
click Apply.
NOTE:
You need to Enable the Internet Wi-Fi Switch and select Wi-Fi.
9
2. Right-click Wireless Network Connection, and then select Properties.
4. Select Obtain an IP address automatically and Obtain DNS
server address automatically, and then click OK to finish the configuration.
•
•
4. Connect to the WLAN device.
There are two methods for your reference.
u Select the listed SSID, and then click Connect.
u Click Add, input the WLAN device information in the Add Wi-Fi
Hotspot area, and then click Apply.
•
3. Select Internet Protocol(TCP/IP), and then click Properties.
•
•
5. After your device connected to the WLAN device successfully, you
can access the Internet.
•
Warning and Notice
Configuring Your PC
10
•
•
11
device if required.
The use of electronic transmitting devices is forbidden in aircrafts,
at petrol stations and in hospitals. Please observe and obey all
warning signs and switch off your device in these conditions.
Do not touch the inner antenna area if not necessary. Otherwise it
will affect your device’s performance.
Store your device out of the reach of little children. Your device may
cause injury if used as a toy.
Do not touch the metallic parts of your device so as to avoid a burn,
when your device is working.
Using Your Device
To the Owner
Follow the following steps and figures
for Windows XP to configure the Internet
Protocol for your Wi-Fi connection.
1. Right-click My Network Places, and
then select Properties.
on. Turn your device off if necessary. Consult a physician or the
manufacturer of the medical device before using your device.
The device complies with RF specifications when the device is used
at 1cm from your body.
Be aware of the usage limitation when using your device at places
such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Turn off your
Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded, such as the
electronic system of vehicles. Please consult the manufacturer of
your device before using if necessary.
Operating your device may interfere with medical devices like hearing aids and pacemakers. Please always keep them more than 20
centimeters away from such medical devices when they are turned
12
•
•
The device is for indoor use only. Do not use the device outside.
The device does not support DFS.
Please use original accessories or accessories that are authorized.
Using any unauthorized accessories may affect your device’s performance, and violate related national regulations about telecom
terminals.
13
•
•
•
•
•
•
Avoid using your device near or inside metallic structures or establishments that can emit electromagnetic waves. Otherwise it may
influence signal reception.
Your device is not waterproof. Please keep it dry and store in a
shady and cool place.
Do not use your device immediately after a sudden temperature
change. In such case, it will produce dew inside and outside your
device, so don’t use it until it becomes dry.
Handle your device carefully. Do not drop, bend or strike it. Otherwise your device will be damaged.
No dismantling by non-professionals and only qualified technicians
can undertake repair work.
Operating temperature range of 0°C ~ +35°C and humidity range of
5% ~ 95% are recommended.
About your Adapter
•
•
•
•
Adapter shall be installed near the equipment and shall be easily
accessible.
Model: ZTE MF93D
Manufacturer: ZTE Corporation
The plug considered as disconnect device of adapter.
Using Battery
•
•
Do not short-circuit the battery, as this can cause excessive heat
and fire.
Do not store the device in hot areas or dispose of it in a fire to avoid
explosion.
14
Do not disassemble or modify the battery.
Never use any charger or battery damaged or worn out.
Return the wear-out battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
WARNING:
Do not change the built-in rechargeable battery in your device by yourself. The battery can only be changed by ZTE or ZTE authorized service provider.
End User shall have no right to reject or return the Product, or receive a
refund for the Product from ZTE under the above-mentioned situations.
• This warranty is End User’s sole remedy and ZTE’s sole liability
for defective or nonconforming items, and is in lieu of all other war-
Limited Warranty
Limitation of Liability
•
ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in
connection with using of this product, whether or not ZTE had been advised, knew or should have known of the possibility of such damages,
including, but not limited to lost profits, interruption of business, cost of
capital, cost of substitute facilities or product, or any downtime cost.
•
•
•
This warranty does not apply to defects or errors in the Product
caused by:
i. Reasonable abrasion.
ii. End User’s failure to follow ZTE’s installation, operation or maintenance instructions or procedures.
iii. End User’s mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the Product.
iv. Modifications or repairs not made by ZTE or a ZTE-certified individual.
v. Power failures, surges, fire, flood, accidents, actions of third
parties or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with thirdparty products provided that such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for
the Product.
15
ranties, expressed, implied or statutory, including but not limited to
the implied warranties of merchantability and fitness for a particular
purpose, unless otherwise required under the mandatory provisions
of the law.
Troubleshooting
Problem
Suggested Solution
• You need to install the software. Run the inCan not establish
stallation program in path of My Computer >
the USB connection
ZTEMODEM.
between your device • If the driver of your device is abnormal,
and PC
please reinstall the software. You need uninstall the software first.
16
Problem
Suggested Solution
Problem
the WPS button to enable
About the password
About the device
• Press the reset button, the device will reset
to the default settings.
• If there is any exception while using the device, please press and hold the Power Button for about 10 s, and the device will restart.
or disable
Wi-Fi function.
Can not establish
• Refresh network list and select the correct SSID.
the Wi-Fi connection
• Check the IP address to make sure your clibetween your device
ent can obtain an IP address automatically in
and client
the Internet protocol (TCP/IP) properties.
• Type the correct network key (Wi-Fi password) when you connect to the device.
• Make sure your (U)SIM card is available.
• Change the location to find a place with good
The client connected
signal.
to the device can not
• Check WAN Connection mode setting.
access the Internet
• Contact with your service provider and confirm your APN settings.
When I use Internet • Make sure the other WLAN device has alWi-Fi mode, the
ready connected to the Internet.
client cannot access • Make sure that the subnet of your device and
the Internet.
the other WLAN device is different
Can not visit the
webGUI configuration page
Suggested Solution
• Press the WPS button twice, and then the
SSID and Wi-Fi connection password appear
on the screen.
• The default password of the webGUI configuration page is admin.
• If you changed the password and forgot the
new password, you need to restore the device to the factory default settings.
• Make sure the Wi-Fi function is active. Press
For more assistance, please:
• Send E-mail to mobile@zte.com.cn
• Visit http://www.ztedevice.com
• Call Service Hotline: +86–755–26779999
• Enter the correct address. The default address is http://192.168.0.1 or http://m.home.
• Only use one network adapter in your PC.
• Do not use any proxy server.
17
18
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising