ZTE | MF65M | User manual | ZTE MF65M User manual

ZTE MF65M User manual
Getting to Know Your Device
Copyright © 2014 ZTE CORPORATION.
All rights reserved.
Let’s go
Getting Started With Your Device
The following figure is for your reference only.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
photocopying and microfilm, without the prior written permission of ZTE
The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without prior
Version No.: R1.0
Edition Time: August 4, 2014
Manual No.: 079584506742
Do not use the device in an enclosed environment or where heat dissipation is poor. Prolonged work in such space may cause excessive heat
and raise ambient temperature, which may lead to automatic shutdown
of the device for your safety. In the case of such event, cool the device in
a well-ventilated place before turning on for normal use.
1. LED Indicators
2. Power Button
3. WPS Button
4. Micro USB Port
5. (U)SIM Card Slot
6. microSDHC Card Slot
The microSDHC™ logo
Red solid
Red solid/ blink- The battery is low.
Please charge the battery.
Error status. Not registered to the mobile network, no (U)SIM card inserted
or no network service available.
Green solid
Registered to the mobile network.
Green blinking
Connected to the mobile network and
data is being transferred.
Blue blinking
Wi-Fi is active.
Blue solid
WPS is active.
LED light off
Wi-Fi is off or your device is in sleep
Blue solid
You have unread messages.
Blue blinking
You have new messages.
LED light off
No messages.
Blinks every 2 seconds when the
battery is being charged.
Blinks every 8 seconds when your
device is in sleep mode and not being charged.
Green blinking
Green solid
The battery level is middle or high.
LED light off
Your device is in standby mode and
not being charged, or the battery is not
Connection Scenario
The device can access the Internet in two ways and allows multiple clients to surf on the Internet at the same time. The following figures are for
your reference only.
• 3G Mode: A SIM or USIM card can be used to access the Internet.
is a trademark of SD-3C, LLC.
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Postcode: 518057
Internet Wi-Fi Mode: Your device can be connected to a Wi-Fi device (such as a hotspot device or wireless router) through Wi-Fi to access the Internet. The Wi-Fi device must be already connected to the
Your device and the Wi-Fi device must be in different subnets.
2. Install the SIM card.
Your device does not support the Micro/Nano SIM card or any other
nonstandard SIM cards. To avoid damaging the device, do not use those
cards or any card holders.
You can find the default SSID on the label of your device.
4. Enter the password, and then click Connect.
4. Install the battery.
5. Close the back cover.
Set the client to obtain an IP address automatically. For the detailed procedure, refer to Configuring Your PC. The client gets an IP address, for
3. Select the SSID of your device, and then click Connect.
Installing Your Device
1. Slide the back cover and remove it.
3. Insert the microSDHC card if necessary.
You may need to enter the password for the Wi-Fi connection. You can
view the label on your device to get the default password.
5. Wait until the client is connected to your device successfully.
Connecting Your Device
Using Wi-Fi
1. Power on your device.
2. Use the Wi-Fi application on a client to search for available wireless
Using a USB Cable
1. Connect a client to your device through a USB cable.
To modify the parameters of your device, log in to the webGUI configuration page by visiting or http:// ufi.ztedevice.com. The
default password is admin.
2. Right-click Wireless Network Connection and select Properties.
4. Select Obtain an IP address automatically and Obtain DNS server
address automatically, and click OK.
Internet Wi-Fi Mode
2. Power on your device. The operating system detects and identifies
new hardware, and automatically finishes the installation.
NOTE: If the system does not automatically launch installation, you can
run the installation program in the My Computer/ ZTEMODEM path.
3. Wait until the client is connected to your device successfully.
1. Log in to the webGUI configuration page.
2. Select Settings > Internet Wi-Fi.
3. Set the Internet Wi-Fi Switch and Preferred Network, and then
click Apply.
You need to set the Internet Wi-Fi Enable and select Wi-Fi.
After the client is successfully connected to the Wi-Fi device, you can access the Internet.
Configuring Your PC
The following procedure describes how to configure the Internet Protocol
in the Windows XP operating system for your Wi-Fi connection.
1. Right-click My Network Places and select Properties.
Accessing the Internet
3. Select Internet Protocol (TCP/IP) and click Properties.
Warning and Notice
3G Mode
After a client is successfully connected to your device, you can access the
Internet in Automatic or Manual mode. The default mode is Automatic.
Your device is automatically connected to the Internet,
and you can surf the Internet through the client.
Log in to the webGUI configuration page, select Settings
> Network Settings > Dial-up Settings > WAN Connection Mode > Manual, (To change current setting,
please disconnect from network) and then click Connect.
the manufacturers of medical instruments before using the device if
Be aware of the usage limitation when using the device at places
such as oil warehouses or chemical factories, where there are explosive gases or explosive products being processed. Turn off the device
if necessary.
Do not use electronic transmission devices in aircrafts, at petrol stations or in hospitals. Observe and obey all warning signs, and turn off
the device in these conditions.
Do not touch the inner antenna area unless it is necessary. Otherwise
the performance of the device may be affected.
Keep the device out of the reach of little children. The device may
cause an injury if used as a toy.
When the device is operating, do not touch the metallic parts. Failing
to do so may cause burns.
Using Your Device
Use original accessories or accessories that are authorized. Using
any unauthorized accessories may affect the performance of the
device and violate the related national regulations about telecom terminals.
Avoid using the device near or inside metallic structures or establishments that can emit electromagnetic waves, because signal reception
may be affected.
The device is not waterproof. Keep the device dry and store it in a
shady and cool place.
To the Owner
4. Connect your device to a Wi-Fi device.
There are two methods:
Input the Wi-Fi Hotspot information in the Add Wi-Fi Hotspot
area, and then click Apply.
Select this Wi-Fi Hotspot which will be listed, input the Pass
Phrase and click Apply.
Do not use the device immediately after a sudden temperature
change. In such case, dew may be generated inside and outside the
device, so do not use it until it becomes dry.
Handle the device carefully. Do not drop, bend or strike it. Otherwise
the device may be damaged.
Only qualified personnel can dismantle and repair the device.
An operating temperature between 0°C and +40°C and a humidity
between 5% and 95% are recommended.
Using the Battery
Do not connect the battery in a short circuit, because a short circuit
may cause excessive heat and fire.
• Do not store the battery in a hot area or put it in a fire. This avoids an
• Do not disassemble or modify the battery.
• If the battery is not used for a long period, remove it from your device
and store it in a cool dry place.
• Never use a damaged charger and exhausted battery.
• Return the exhausted battery to the provider or put it in the appointed
recycle place. Do not put it in familial rubbish.
If the battery is broken, keep away from it. If it taints your skin, wash your
skin with abundant fresh water and ask doctor help if necessary.
Limited Warranty
This warranty does not apply to defects or errors in the product
caused by:
i. Reasonable abrasion.
ii. End users’ failure to follow ZTE’s installation, operation or maintenance instructions or procedures.
iii. End users’ mishandling, misuse, negligence, or improper installation, disassembly, storage, servicing or operation of the product.
iv. Modifications or repairs not provided by ZTE or a ZTE-certified
v. Power failures, surges, fire, flood, accidents, and actions of third
parties or other events outside ZTE’s reasonable control.
vi. Usage of third-party products, or usage in conjunction with thirdparty products if such defects are due to the combined usage.
vii. Any other cause beyond the range of normal usage intended for
the product.
End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations.
• This warranty is end users’ sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties, expressed, implied or statutory, including but not limited to the
implied warranties of merchantability and fitness for a particular purpose, unless otherwise required under the mandatory provisions of
the law.
including, but not limited to lost profits, interruption of business, cost of
capital, cost of substitute facilities or product, or any downtime cost.
Limitation of Liability
Failing to establish a
connection between
your device and a PC
through a USB cable
Failing to establish a
connection between
your device and a client through Wi-Fi
ZTE shall not be liable for any loss of profits or indirect, special, incidental
or consequential damages resulting from or arising out of or in connection with using of this product, no matter whether or not ZTE had been
advised, knew or should have known of the possibility of such damages,
The client cannot access the Internet in
Internet Wi-Fi mode
Recommended Action
The client connected
to the device cannot
access the Internet
If inadequately shielded, some electronic devices may be affected by
the electromagnetic interference caused by the device, such as the
electronic system of vehicles. Consult the manufacturers of such devices before using the device if necessary.
Operating the device may interfere with medical instruments such as
hearing aids and pacemakers. Always keep the device more than 20
centimeters away from such medical instruments when your device
is turned on. Turn the device off if necessary. Consult a physician or
Install the software. Run the installation
program in the My Computer/ ZTEMODEM
If the driver of your device is abnormal, uninstall and reinstall the software.
Ensure that the Wi-Fi function is enabled.
Refresh the network list and select the correct SSID.
Check the IP address, and ensure that
your client can automatically obtain an IP
Ensure that your (U)SIM card is available.
Change the location and find a place with
good signal.
Check the setting of the WAN connection
Contact your service provider and confirm
your APN settings.
Failing to visit the
webGUI configuration
About the password
Ensure that the Wi-Fi device has already
been connected to the Internet.
Ensure that your device and the Wi-Fi device are in different subnets.
Enter the correct address. The default
address is or http:// ufi.
Use only one network adapter in your PC.
Do not use any proxy server.
For the Wi-Fi connection password, view
the label on the device.
The default password of the webGUI configuration page is admin.
If you changed the password and forgot
the new password, you need to restore the
device to the factory default settings.
You can get help by:
• Sending an E-mail to mobile@zte.com.cn
• Visiting www.ztedevice.com
• Calling the service hotline +86–755–26779999
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF