ZTE | MF30 | User manual | ZTE MF30 User manual

ZTE MF30 User manual
Smar
o De
vice User Guide
Smartt Br
Bro
Device
(ZTE MF30)
No.55, Hi-tech Road South, ShenZhen, P.R.China
Postcode : 518057
Service Hotline:+86-755-26779999
http://www.zte.com.cn
E-mail: mobile@zte.com.cn
1
Table of Contents:
I. Overview
Product Overview
What’s in the Box?
Led Indicators of the Smart Bro Device
II. Using the Smart Bro Device
Setting Up the Smart Bro Device
-
Setting Up
Inserting the Smart Bro SIM Card into the Smart Bro De-
vice
Charging the Smart Bro Device using the USB Cable and
inserting the Micro SD Card.
Closing the back cover of the Smart Device.
Powering ON the Smart Bro Device
System Requirements
Connecting to the Internet
Disconnecting from the Internet
Logging into the Smart Bro Device
III. Troubleshooting the Smart Bro Device
2
I. Overview
A. Product Overview
The Smart Bro Device is an easy-to-install portable WiFi router for
broadband connection that can be shared anytime and anywhere.
#
Description
1
Power Key
2
Memory card slot
3
WPS - This button used to start Wi-Fi
Protected Setup authentication process.
4
Power Indicator
5
Charger / Mini USB port
3
B. What’s in the Box?
Item
Description
Smart Bro Device
3G Wireless Router
USB Data Cable
The USB Data Cable can be
used in charging the device
and using it as a modem.
Smart Bro Device Quick
Guide in setting up the Smart
Start Guide / User Guide
Bro Device
C. Led Indicators of the Smart Bro Device
Indicator
Status
Description
Red glittering
Please charge
Battery
Red bright
Voltage of battery is low
indication
Green glittering
Charging
Green bright
Voltage of battery is high
4
Indicator
Status
Description
Signal
strength
Red bright
ERROR or NO signal
Green glittering
Signal is ok
indication
Green bright
Signal is good
WIFI
Blue glittering
WIFI is active
indication
Blue bright
WPS is active
RED glittering
2G Modem data transferring
RED bright
Register on 2G network
Network
indication
GREEN glittering 3G Modem data transferring,
Register on 3G network
GREEN bright
5
II. Using the Smart Bro Device
Setting Up the Smart Bro Device
Note: Please make sure that the Smart Bro Device is turned OFF
before inserting the Smart Bro SIM Card. Inserting the Smart Bro
SIM Card while the router is turned ON would lead to probable damage on the SIM Card and/or on the Smart Bro Device.
A. Inserting the Smart Bro SIM Card into the Smart Bro Device
1. Open the back cover of the Smart Bro Device and take out the
battery. The SIM slot can be found once the battery is taken out.
Follow the diagram below:
2. Inserting the Smart Bro SIM Card into the
Smart Bro Device.
6
Note: Make sure that the Smart Bro SIM is pushed all the way down
as shown in the diagram above.
3. Close the back cover of the Smart Device.
B. Charging the Smart Bro Device using the USB Cable and Inserting the Micro SD Card.
1. Charging the Smart Bro Device using the USB Cable.
Connect the USB Cable as seen in the diagram below.
Initial charging time is 2hrs to 3 hrs.
Note:
Insert the charger lead carefully with the plug arrow facing the
bottom of the device.
The plug only fits one way. Do not use excessive force to insert
the plug.
Check if the plug is lined up correctly against the device; then
insert it gently.
7
2. Inserting the Micro SD.
Slowly open the cover of the Micro SD slot
Ensure that your Micro SD is facing the right way before inserting
it into the slot
Note: There is no Micro SD bundled with the Smart Bro Device.
C. Powering ON/OFF the Smart Bro Device
Press and hold the Power Button for five seconds to switch the
device ON or OFF.
D. System Requirements
PC Type Hardware
Operating
Web
System
Browser
A. Pentium III or Higher
B. 512MB of RAM or
Higher
Windows,
Non-Mac C. LAN Card (Optional)
Ubuntu
D. At least 10GB of hard
disk space
E. With WiFi Capability
8
Internet
Explorer,
Mozilla,
Firefox,
Maxthon,
etc.
PC Type Hardware
Operating
System
Web
Browser
Tiger, Leopard,
Snow Leopard
Safari, etc.
A. Power PC G3, G4,
MAC
G5 processor.
B. 256MB RAM
C. At least 3GB of
hard disk space
Note: The Smart Bro Device should be used with a WiFi cable PC/
Laptop and/or with WiFi capable gadgets.
E. Connecting/Disconnecting to the Internet
9
1. Preparation
Before connecting to the internet, please make sure that the:
- The Smart Bro SIM card is properly inserted into the Smart
-
Bro Device.
The Smart Bro Device is charged.
2. Connecting/Disconnecting from the Internet
Note: Please make sure that the WiFi of your Laptop/PC/Other WiFi
capable devices is/are turned ON.
In your computer, kindly access the “wireless connection” and
click on “search for nearby wireless connections”.
The default SSID of the Smart Bro Device is Smartbro_XXXXXX
(the Xs is the MAC Address of the Smart Bro Device. E.g.
Smartbro_09E123). The SSID is the name of the router that you
will see when you “search for nearby wireless connections”.
Click on Smartbro_XXXXXX and then click on Connect; OR,
you can double click on the name Smartbro_XXXXXX to connect to the router and internet. The steps in connecting your computer to the Smart Bro Device and to the internet may vary depending on the computer/device type, operating system and wire-
less connection software being used.
Once the connection to the Smart Bro Device is established, you
can now browse the internet.
To disconnect from the internet, go to your wireless connection
and click on Smartbro_XXXXXX. After clicking Smart Bro, click
on the disconnect button.
10
Logging into the Smart Bro Device
Note: Do not change any settings unless instructed by your service
provider. To make changes to your settings you need to disconnect
the router from the internet but maintain connection from your computer to the router. After making changes, reboot the Smart Bro
Device.
A. Logging into Smart Bro Device User Interface (UI)
1. Once connection to the Smart Bro Device was established, open
your web browser and type in http://192.168.0.1
2. In the login page, the default username is smartbro and the
default password is smartbro. Take note that username and
password are case sensitive.
11
B. Inside the Smart Bro Device UI
1. Home Page
Shows the general state/condition of the router.
2. Quick Setup
The quick setup guide will show you how to set the basic parameters for your router the safest way. Please take note that all
configuration settings needed for connecting to the internet has
already been pre-defined.
12
3. WAN Connection
There are three connection mode:
- Auto Connect: The router will automatically connect to WAN
-
when it is powered on.
On Demand Connect: .The connection will be established
when data transmission is required. Router will disconnect
from the Internet if there is no data traffic going through it
during the Max Idle Time.
Manual Connect: Connect to the Internet manually.
By default, the Smart Bro Device is set to Auto Connect.
13
4. 3G Setting
Wireless Info
14
Network Select
APN Setting
15
5. Router
LAN
DHCP Client
16
6. WiFi Setting
Station List
Basic
17
Security
WPS
18
7. Firewall
MAC/IP/Port Filtering
Port Forwarding
19
System Security
8. Advanced
Status
20
Management
Restore
21
Pin Manage
22
III. Troubleshooting the Smart Bro
Device
A. Power
Check if the Smart Bro Device has power/enough power to
function.
In charging the Smart Bro Device, ensure that the USB cable is
properly plugged into the Smart Bro Device and computer/laptop.
Press and hold the Power Button for five seconds to switch the
product ON or OFF.
B. Cannot Connect to the Internet
-
No Signal/Service – Please make sure of the following:
You are in an area with Smart Bro Device Coverage.
-
You are using a Smart Bro SIM.
Ensure that the Smart Bro SIM is inserted properly inside the
Smart Bro Device.
Check the Smart Bro Device connection status from the User
Interface.
23
C. Additional Troubleshooting Help
Contact Smart Bro Hotline *1888 (smart mobile) / 6727277 / 1800106727277 / customercare@smart.com.ph
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising