ZTE | AX326 | User manual | ZTE AX326 User manual

ZTE AX326 User manual
Copyright © 2011 by ZTE Corporation
All rights reserved.
No part of this publication may be excerpted, reproduced, translated or
utilized in any form or by any means, electronic or mechanical, including
ZTE AX326 WiMAX USB MODEM
Quick User Guide
photocopying and microfilm, without the prior written permission of ZTE
Corporation.
The manual is published by ZTE Corporation. We reserve the right to
make modifications on print errors or update specifications without prior
notice.
Introduction
Hardware removal from your system
4
Up Rate
Thank you for choosing ZTE AX326 WiMAX USB MODEM (hereinafter
Close the CM application, safely remove hardware and then remove
your Modem.
5
Down Rate
Show the download rate.
6
Status Bar
Shows Modem status: No Device,
Searching, Wait for Connection, Connect-
7
Manual
Authentication
referred to as Modem). It is next generation mobile broadband that’s
designed to work as fast around town as it does at home.
To guarantee your Modem always work in its best condition, please read
this guide carefully and keep it for future use. The pictures, symbols
How to use your Modem
When you launch Modem Connection Manager, the CM interface will be
Connecting the Modem to PC
Mode of Access
WiMAX (Worldwide Interoperability for
Microwave Access)
Manual number: 079584502573
WiMAX Protocol
802.16e (IEEE 802.16-2005)
Frequency Allocation 3400-3600MHz
NO. 55, Hi-tech Road South, ShenZhen, P.R.China
Zip Code: 518057
Service Hotline: +86-755-26779999
E-mail: mobile@zte.com.cn
http://www.zte.com.cn
1
2
Dimension (WxDxH)
76mm x 25mm x 11.3mm
Weight
Approx 20g
3
z
tightly inserted.
When you insert the Modem into computer for the first time, your
system will detect the new hardware automatically.
4
2
5
10
installation prompt should appear automatically. Follow the system
prompts to complete the software installation.
you need to check the configuration of your computer and make sure that
the CD Self-start function is turned on. If this question still exists, you
The following figure shows the appearance of AX326. It is only for your
reference. The actual product may be different.
can click My Computer and start the installation program by run the
setup.exe from the ZTE_WiMAX_MODEM\Data file folder.
4
8
9
Options
Button
Data Records
Button
6
When you insert the Modem into your computer for the first time, the
Getting to know your device
3
1
Software installation guide
Note: Some antivirus software and firewall software will prevent the CDROM Auto-run. If the installation prompt does not appear automatically,
Configure the Login and Password.
Button
Rotate the USB connector.
Insert the Modem into your computer’s USB port and ensure that it is
The following table shows the specification of your device.
Version: Release 1.0
Date: Jan. 2011
displayed as below:
z
z
Specification
ing and Connected.
1. USB connector: Connect your Modem to the laptop or desktop computer.
and contents in this guide are just for your reference. They might not be
completely identical with your Modem.
Show the upload rate.
7
8
10
Connect
Button
Configures the Modem options.
Show the data records.
Connect/Disconnect to WiMAX network or
wake up the Modem when click Connect
Button
9
1
Signal
Indicator
Shows WiMAX signal strength if the network
is found.
2
Menu Button
There are About, Help, Update and Exit four
submenu when click Menu Button.
3
Operator
Name
FAQs
When you meet the following problems in service, please refer to the
following answers to solve them. If the problems still exist, please
contact with your suppliers.
Show the operator name when the Modem has
connected with Network.
5
6
Problem
Description
Possible
Causes
The system can not The system configuration
run the installation is not suitable for the autoprogram
run.
automatically.
Problem
Solving
Open the disc of the
Modem program and
start the setup.exe. If
you have installed the
other version of installation program please
uninstall it firstly.
Problem
Description
When the Modem is 1. The installation programs
being inserted, the of the Modem haven’t been
notebook computer installed properly.
cannot find it.
After the Modem is The system configuration Please open the UI
plugged in, the UI is not proper.
program manually.
program doesn’t run
automatically.
After restarted the
computer, there is
no signal all the
time.
1. You are in the place Move to the place that
where no WiMAX network has good signal.
coveredsuch as underground parking lot, tunnel
etc.
2. The Modem isn’t con- Pull out and insert the
nected well.
Modem safely again.
7
Possible
Causes
Problem
Solving
1. Run the installation
program first and then
connect the Modem. If
you use the Windows
XP operating system,
install the drivers according to the Windows indication information to operate.
2. The Modem isn’t con- 2. Restart the
nected well.
computer, or connect
the Modem again.
connection failed.
1. You are in the place Move to regions with
where no WiMAX network strong signal.
covered, such as underground parking lot, tunnel
etc.
8
There are no user serviceable parts inside the Modem. Unauthorized
dismantling or repair of the Modem will void the warranty.
Cleaning and Maintenance
z
The Modem is non-waterproof, please keep it dry and store in shady
This warranty is end user’s sole remedy and ZTE’s sole liability for
defective or nonconforming items, and is in lieu of all other warranties,
z
This Modem generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
z
and cool place.
Do not use or store the device in dusty or dirty areas, since its
expressed, implied or statutory, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose, un-
moving parts and electronic components can be damaged in such
environment.
less otherwise required under the mandatory provisions of the law.
Limitation of Liability
If you want to clean your Modem, please use clean fabric that is a bit
wet or anti-static. Do not use harsh chemical cleaning solvents or
ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in
receiving of signals.
Don’t use the Modem immediately after a sudden temperature change
strong detergents to clean your Modem, such as alcohol, dilution
agent and benzene. Power-off your Modem before you clean it.
connection with using this product, whether or not ZTE had been advised,
knew or should have known the possibility of such damages.
in using. Power off Modem if it is necessary. Consult a physician or
the manufacturer of the medical device before using the Modem.
e.g. from an air conditioned environment to high temperature and
humidity outside. In such cases there could be condensing moisture
Limited Warranty
The warranty does not apply to defects or errors in the product caused
Be aware of the usage limitation when using a Modem at places such
as oil warehouses or chemical factories, where there are explosive
inside the Modem which can cause internal damage. Unplug the
Modem and leave it for 30 minutes before use.
by:
(a) Reasonable abrasion.
z
Take the Modem carefully. Don’t drop, bend, knock or harshly treat
it to avoid destructive damage.
(b) Misuse including mishandling, physical damage, improper installation,
unauthorized disassembly of the product.
z
Do not attempt to disassemble the Modem by yourself. Changes
and modifications made to the Modem without the approval of manu-
(c) Water or any other liquid damage.
(d) Any unauthorized repair or modification.
To the user
z
Some electronic devices are susceptible to electromagnetic interference sent by Modem if inadequately shielded, such as electronic
system of vehicles. Please consult the manufacturer of the device
z
before using the Modem if necessary.
Operating laptop and Modem may interfere with medical devices like
hearing aids and pacemakers. Please always keep the Modem more
than 20 centimeters away from such medical devices when they are
z
gases or explosive products being processed. Do not use Modem if
necessary.
z
Do not use Modem at gas station.
The Modem contains sensitive electronic circuitry. Do not expose
z
the Modem to any liquids, high temperatures or shock.
Store the Modem out of the reach of small children. The Modem may
z
cause injury if used as a toy.
Only use original accessories or accessories that are authorized by
z
2.The network is busy now. Try again later.
3.The manual authentica- Please contact your
tion setting is error.
operator
z
Safety Warning and Notice
may cause harmful interference to radio communications.
Modem
z
z
Avoid using the Modem near metallic structure device or establishment that can emit electromagnet wave. Otherwise it may influence
facturer could void your authority to operate this Modem.
In Aircraft
z
(e) Power surges, lightning damage, fire, flood or other events outside
ZTE’s reasonable control.
Please power off the Modem before the airplane takes off. In order
to protect airplane’s communication system from interference, it is
(f) Use of the product with any unauthorized third party products such
as generic chargers.
the manufacturer. Using unauthorized accessories may affect your
Modem’s performance, damage your Modem and violate related
never allowed to use the Modem when it is in flight. Using it before
the airplane taking off should get aircrew’s permission according to
(g) Any other cause beyond the range of normal usage for products.
End User shall have no right to reject, return, or receive a refund for any
national regulations.
safety regulations.
product from ZTE under the above-mentioned situations.
9
z
10
11
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising