Eiki | EK-510 | manual | EIKI EK-510 Manual

EIKI EK-510 Manual
Edge blending
adjustment
manual
V1.0
Edge Blending function
Edge Blending function could project bigger and brighter with high resolution pictures via multi
projector. The Edge Blending software could adjust the color and the effect of the overlay edge.
Equipment:
2 or more projector with same resolution, Video duplicator, RS232 series cable.
Connection:
(1)Setting the projectors with the same level from ground and the same projection
distance from screen.
(2)Project the image through the video duplicator to each projecotr.
(3)Connect the computer and projectors via RS232 cable.
......
Projector#1
Projector#2
Projector#N
Video
cable
Video cable
Video
cable
Video cable
Video duplicator
RS232 cable
RS232
cable
RS232
cable
RS232 cable
Computer
Setting:
(1)Setting the projected image as the same dimension by each projector.
(2)Press Menu button on the remote controller or control panel to pop up the OSD.
(3)Press ▲▼ button to select "Display"
(4)Press ▲▼ button to select "Aspect"
(5)Press ▲▼ button to select "Advanced" and press OK to ready for Edge Blending
function.
Adjustment:
The color and effect of the overlay edge can be adjusted with the Edge Blending
software.
The Edge Blending Software and its manual can be downloaded from EIKI website.
URL: http://www.eiki.com
Note:
●● Edge Blending function can only effected with the same resolution projectors.
●● Edge Blending function can apply via HDMI, VGA and RGBHV as input source.
●● Setting the same lavel and prosition with the same dimension image would make the better
effect after edge blending adjustment.
2
Edge Blending function
Launch the "Edge blending" software to make edge blending operation.
(1)Select the quantity number from "columns" and "rows" from the upper left corner of main page,
according to the actual setting. Then click the "Arrange" button to make arrangements.
(2)Click the "Connect" button, then set up all ID number about the projector.
click the "Connect" button, you will see all the valid ID numbers about COM ports (displayed according to
the actual connection), then click the “Connect” button again to search the projector connected to the computer. If the connection is not properly, the pop-up message will remind you to click the button once again. Once
the connection is well and the software could searched the projector, the "input information" dialog box would
pop-up.
3
Edge Blending function
Then the projector screen will jump out a red "00" dialogue with white fonts. Next, keyin the corresponding
location ID number according to arrangement, and click "Connect" button until all projectors's ID numbers
match successfully. Then the "Connected successfully" message will displays.
Note:
● Do not operate the software when the click mouse is busy while performing the operation.
(3)Click the "Test Pattern" button from the lower left corner of the main page, then the "Guide to
expand the window" pops up. According to the guidance operation to project the Test Pattern
and then return to the computer "display" window. During that procress, you can select different
Test Pattern.
Note:
● In the process of Test Pattern, you can double-click the left button of mouse to exit it.
(4)Get into Position operation.
1.click the “Blending Calculation” button of Aided Operationin column in the lower right corner of the main
page, then the “Blending Calcalation” dialog window will pop up.
2.Keyin the Display Aspect Ratio accoding the final image.
3.Click the “Run” button to calculate and write down the H blending band and the V blending band.
4.Close the “Blending Calcalation” dialog box.
4
Edge Blending function
5.Keyin the blending band value according the result of the calculater (for example, H direction 840 and the
V direction 0) in the upper right corner, then click "position" button.
6.The prjetcted screen will display rectangular box consisting of green line (left and upper side), purple line
(right and lower side) and white rectangle (inner side and outer side)
Note:
● If the white rectangle has departure from the green and purple line, please check the resolution
setting of the projector.
● Please note the figure of position operation might be different via the value of the blending band.
(5)Adjust the edge blending area.
1.Move the projected image to overlap as the figue below:
2.Make the two line of the overlap edge combine as one via lens shift function.
3.Click on the “Geometry Correction” button from Aided Operation bar for advance adjustment.
5
Edge Blending function
<Usage of the Geometry Correction>
1. Click the “Geometry Correction” button from Aided Operation bar, the adjustment window will pop-up.
2. Select the projected image you would like to adjust from the Location ID.
3. Adjust the value of the corner to make the edge of overlap area as close as one.
4. Press F5 as preview the effect after adjust the value.
5. Press F2 to save the adjustment.
Note:
● When change the value of corner, the point would turn to green from yellow.
● After save the adjustment, the point would turn to yellow.
(6)Get into the splitting operation.
The horizontal and vertical reproduction rates can be selected according to the actual setting.
Then click “Split” to pojected the imgae separably.
(7)Get into the Edge Blending operation.
Click the “Blend” button to check the edge blending effect of the image
Make adjustments of the brightness of the blending regions by movieng the adjust bar.
Or you could adjust the black level of the blending regions by the following step:
1. Setting the “Test Pattern” as :Black
6
Edge Blending function
2.Click on the screen figure that you want to adjust.
3.The black level adjustment window would pops up.
Note:
●Red area: adjust the black level correction of the projected image
Yellow area: the area with edge blending effect
Purple section: adjustment the width of the blending
●Press F5 as preview the effect after adjust the value.
Press F2 to save the adjustment.
7
Edge Blending function
(8)Save / Reset the edge blending setting
<Save>
Press the “Save” button to save the setting of edge blending.
The Pop-up window would show the confirmation.
<Reset>
Press the “Reset” button to remove the setting of edge blending.
The Pop-up window would shown as below:
Yes........ Reset all the setting of edge blending.
No.......... Restart to setting from “Position” of edge blending.
Cancel... Get back to the setting main page.
8
Trouble shooting
1 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Connect" operation during the
second step.
Analysis The edge blending function
needs configuration permissions
where replace the motherboard.
Solution Please contact the after sales
specialist.
2 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Connect" operation during the
second step.
Analysis The resolution of projectors for
edge blending are different.
Solution Make all projectors are of the
same physical resolution for
blending
3 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Connect" operation during the
second step.
Analysis Only when the "Screen size" is
set to "Advanced", can the edge
blending function are valid.
Solution Set the "Screen size" to
"Advanced" in the "Display" of
OSD. Please check "Setting" on
page 2. .
4 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Connect" operation during the
second step.
Analysis The default setting of Start up
logo has been changed.
Solution
Set the Start up logo as default.
9
Trouble shooting
5 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Connect" operation during the
second step.
Analysis 1) The ID is repeated that make
the software cannot connect
successfully;
2) Projector is disconnected with
the PC.
Solution 1) Check whether the ID is
repeated or not. If so, please
enter the correct ID.
2) Check whether the PC and
the projector are connected
when the ID is correct.
6 Question The ID do not match with the first
step configuration permissions
where replace the motherboard.
Analysis The edge blending function
needs configuration permissions
where replace the motherboard.
Solution Input the correct ID number
according to the one in the first
step.
7 Question The screen pops up as "Error"
window just as shown in the
right image when you execute
"Position" operation.
Analysis The communication between
the PC and the projector's serial
cable is wrong.
Solution Check whether the PC and the
projector are connected. If not,
please connect them together
before you execute Position
operation.
8 Question The screen pops up as "Error"
window just as shown in the right
image when you execute "Split"
operation.
Analysis The communication between
the PC and the projector's serial
cable is wrong.
Solution Check whether the PC and the
projector are connected. If not,
please connect them together
before you execute Split
operation.
10
Trouble shooting
9 Question The screen pops up as "Error"
window just as shown in the
right image when you make
"Connect" during the second
step.
Analysis The communication between
the PC and the projector's serial
cable is wrong.
Solution Check whether the PC and the
projector are connected. If not,
please connect them together
before you execute Save
operation.
10 Question The screen pops up as "Error"
window about invalid port
number just as shown in the
right image.
Analysis The serial connection is lost
during your operation step
especially when the USB
connector is removed from the
PC.
Solution Check whether the PC and the
serial cable are connected.
Maybe users need make
resetting before connectting
them
11 Question The screen pops up as "Error"
window about invalid port
number just as shown in the
right image.
Analysis The software is not compatable
with the PC system
Solution Close the software, then right
click the software to select "Run
as administrator" to run up the
software.
11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising