Eiki | LC-WBS500 | manual | EIKI LC-WBS500 Manual

EIKI LC-WBS500 Manual
OWNER'S MANUAL
LC-XBS500
LC-WBS500
Maintenance and cleaning
Be sure to clean filter #1 (page 72) and #2
Cleaning air filter # 2
The air filter prevents dust from accumulating on the surface of the optical elements inside
the projector. Should the air filter become clogged with dust particles, it will reduce cooling
fans’ effectiveness and may result in a buildup of internal heat and adversely affects the life of
the projector. If the Filter warning icon appears on the screen, the air filter should be cleaned
immediately. Clean the air filter following the steps below.
1 Turn off the projector, and unplug the AC
power cord from the AC outlet.
2 Remove the air filter.
3 Gently clean the filter with a brush.
4 Reinstall the filter into the projector properly.
Caution
Do not operate the projector with
the air filter removed. Dust may
accumulate on the optical elements,
degrading picture quality.
Do not put any small objects into the
air intake vents. Otherwise, it may
result in malfunction of the projector.
Filter counter reset
Be sure to reset the filter counter after cleaning
or replacing the filter.
1. Press Menu on the remote control to display
the screen menu. Press to select
"Expand", then press the OK button.
2. Press  to select "Filter counter", and then
press the OK button.
Press  to select "Filter counter reset" and
press the OK button, "Filter counter
Reset?" appears on screen, select "Yes" to
continue.
3. When another dialog box pops up, select
"Yes" to reset the filter.
Recommendation
We recommend avoiding dusty/smoky
environments when you operate the projector.
Usage in these environments may cause poor
image quality.
When you use the projector under dusty or
smoky conditions, dust may accumulate on the
lens, LCD panels, or optical elements inside the
projector. When the symptoms above are
noticed, contact your authorized dealer or
service station for proper cleaning.
Features and Design
This Projector is designed with the most advanced technology for portability, durability, and ease
of use. This projector utilizes built-in multimedia features, a palette of 10.7 million colors, and
matrix liquid crystal display (LCD) technology.
Simple Computer System Setting
The projector has the Multi-scan system to
conform to almost all computer output signals
quickly. Up to WUXGA resolution can be
accepted.
LAN Network Function
This projector is loaded with the wired and
wireless LAN network function. You can
operate and manage the projector via network.
( Page 59-66.)
Useful Functions for Presentations
The digital zoom function allows you to
focus on the crucial information during a
presentation.
Auto Setup Function
This function enables input source search, auto
pc adjust and auto keystone by simple pressing
the AUTO button on the remote control.
Lamp Control
Brightness of the projection lamp can be
selected.
Colorboard Function
At the time of simple projection on the colored
wall, you can get the close color image to the
color image projected on a white screen by
selecting the similar color to the wall color from
the preset four colors.
Logo Function
The Logo function allows you to customize the
screen logo.
Multilanguage Menu Display
This projector provides multi-language screen
menu.
Switchable Interface Terminal
The projector provides a switchable interface
terminal. You can use the terminal as computer
input or monitor output conveniently.
Helpful Maintenance Functions
Lamp and filter maintenance functions provide
for better and proper maintenance of the
projector.
Power Management
The Power management function reduces
power consumption and maintains the lamp
life.
Security Function
The Security function helps you to ensure
security of the projector. With the Key lock
function, you can lock the operation on the
top control or remote control. PIN code lock
function prevents unauthorized use of the
projector.
Closed Caption
This is a printed version of the program sound
or other information displayed on the screen.
You can turn on the feature and switch the
channels.
Note:
- The screen menu and pictures in the manual may slightly differ from the real product.
- The manual is subject to change without prior notice.
2
Contents
Features and Design
Contents
Safety Instructions
Safety Guide
Air circulation
Installing the projector properly
Moving the projector
Compliance
Accessories
Part names and functions
Front
Back
Bottom
Terminals
Top control and Indicators
Remote control
Install remote control batteries
Operating range
Wired Remote Control Transmitter
Installation
Positioning the projector
Adjustable foot
Lens shift adjustment
Connecting to computer (Digital and
analog RGB)
Connecting to video equipment
(Video, S-Video)
Connecting to audio equipment
Connecting to USB device (USB-A, USB-B)
Connecting the AC power cord
Basic operation
Turn on the projector
Turn off the projector
How to operate the screen menu
Menu bar
Adjust zoom and focus
Lens shift adjustment
Auto setup function
Keystone
Volume
Remote control operation
Input select
Display
Auto PC adj.
Fine sync
H Position
V Position
H.Size
Aspect
Project Way
Menu Position
Background Display
System
Color adjust
Image Mode
Color adjust (Computer)
Color adjust (Video,S-video,Component)
2
3
4
5
6
6
7
8
9
10
10
10
10
11
12
13
15
15
15
16
16
16
17
18
19
20
21
22
23
23
24
25
26
27
27
27
28
29
30
32
34
34
34
34
34
34
35
35
35
36
36
38
38
39
40
Setting
On start
Standby mode
High land
Lamp control
Cooling fast
Closed Caption
Key lock
Iris
Terminal
Sound
HDMI setup
Expand
Language
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test Pattern
Network
Remote control
Factory default
Lamp counter
Memory viewer
Set Slide
Slide transition effect
Sort Order
Rotate
Best Fit
Repeat
Apply
Information
Network Control Instructions
LAN control
Using useful functions
Memory Viewer function
USB Display function
Maintenance and cleaning
WARNING indicator
Cleaning the filter
Filter counter reset
Clean the projector lens
Clean the cabinet
Replace the lamp
Order Replacement lamp
Appendix
Troubleshooting
Menu Tree
Indicator and projector state
Compatible computer specifications
Technical Specifications
Configurations of terminals
Content of hazardous substances and elements
Dimensions
PIN code memorandum
RS232 Control Method
41
41
41
42
42
42
43
43
44
44
44
45
46
46
46
47
49
50
51
52
52
53
54
54
55
56
56
56
56
57
57
57
57
58
59
59
67
67
69
71
71
72
72
73
73
74
75
76
76
78
82
83
85
86
87
87
88
89
3
Safety Instructions
Please read this manual completely before installing
and operating the projector.
The projector provides many convenient features
and functions. Proper operation may enable you to
fully utilize the features and keep it in good condition.
Otherwise, it will not only shorten the service life of
the unit, but also may cause malfunction, a fire, or
other accidents.
If your projector cannot work properly, please read
this manual again, check the operating methods and
cable connection, and try the solutions in the part of
Troubleshooting. If the problem still exists, contact the
dealer or the service center.
The lamp of the projector is a wearing part. The
luminance may decrease after a period of operation
and be weaker than that of a new lamp. This is
normal. Please strictly follow the steps in Turning
on the unit and Turning off the unit to turn on/off
the projector, and the requirements in Maintaining
and cleaning the projector to service and clean the
projector regularly. Otherwise the high temperature
residual heat may not radiate, greatly shorten the
service life of the projector and lamp, or even damage
them within a short period.
Caution
Safety precautions
Caution: ● The projector must be grounded.
● Do not expose the projector to
raindrops or high humidity to avoid
a fire or electric shock.
- This projector produces intense light from the
projection lens. Avoid staring directly into the
lens, otherwise eye damage could be caused.
Be especially careful that children do not stare
directly into the beam.
- Place the projector in a proper position.
Otherwise it may result in fire hazard.
- Leave an appropriate space from the top,
sides, and back of the shell in order to ventilate
and cool down the projector. The figures below
indicate the minimum distance to be left. It must
be satisfied if the projector is placed in sealed
environment like a cabinet.
SIDE and TOP
REAR
0.7’(20cm)
ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE EXCEPT
LAMP REPLACEMENT. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
T H I S S Y M B O L I N D I C AT E S
T H AT D A N G E R O U S V O LTA G E
CONSTITUTING A RISK OF ELECTRIC
SHOCK IS PRESENT WITHIN THIS
UNIT.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
USER’S MANUAL WITH THIS UNIT.
FOR EU USERS
The symbol mark and recycling systems described below apply to EU
countries and do not apply to countries in other areas of the world.
Your product is designed and manufactured with high quality materials
and components which can be recycled and/or reused.
The symbol mark means that electrical and electronic equipment,
batteries and accumulators, at their end-of-life, should be disposed of
separately from your household waste.
Note:
If a chemical symbol is printed beneath the symbol mark, this chemical
symbol means that the battery or accumulator contains a heavy metal
at a certain concentration. This will be indicated as follows: Hg: mercury,
Cd: cadmium, Pb: lead In the European Union there are separate
collection systems for used electrical and electronic
equipment, batteries and accumulators.
Please, dispose of them correctly at your
local community waste collection/recycling centre.
Please help us to conserve the environment we
live in!
4
1.5’(50cm)
3’(1m)
3’(1m)
- Do not cover the vent of the projector. Poor
radiation may shorten the service life or even
cause dangers.
- Remove the AC power plug if the projector is
not to be used for a long time.
- Do not project the same image for a long time;
otherwise, a residual image may appear on the
LCD panel due to its characteristic.
Caution
Do not set the projector in greasy, wet, or smoky
conditions such as in a kitchen, to prevent a
malfunction or accident. If the projector comes
in contact with oil or chemicals, it may become
deteriorated.
Read and keep this manual for future reference.
The mains plug/appliance coupler is used as
disconnect device, the disconnect device shall
remain readily operable.
Safety Guide
All the safety and operating instructions should be
read before the product is operated.
Do not install the projector near the ventilation duct of
air-conditioning equipment.
Read all of the instructions given here and retain them
for later use. Unplug this projector from AC power
supply before cleaning. Do not use liquid or aerosol
cleaners.
Use a damp cloth for cleaning.
This projector should be operated only from the type
of power source indicated on the marking label. If you
are not sure of the type of power supplied, consult
your authorized dealer or local power company.
Follow all warnings and instructions marked on the
projector.
For added protection to the projector during a lightning
storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet.
This will prevent damage due to lightning and power
line surges.
Do not expose this unit to rain or use near water... for
example, in a wet basement, near a swimming pool,
etc...
Do not use attachments not recommended by the
manufacturer as they may cause hazards.
Do not place this projector on an unstable cart, stand,
or table. The projector may fall, causing serious injury
to a child or an adult, and serious damage to the
projector.
Use only with a cart or stand recommended by the
manufacturer, or sold with the projector. Wall or
shelf mounting should follow the manufacturer’s
instructions, and should use a mounting kit approved
by the manufacturers.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
Slots and openings in the back and bottom of the
cabinet are provided for ventilation, to ensure reliable
operation of the equipment and to protect it from
overheating.
The openings should never be covered with cloth or
other materials, and the bottom opening should not be
blocked by placing the projector on a bed, sofa, rug,
or other similar surface. This projector should never
be placed near or over a radiator or heat register.
This projector should not be placed in a built- in
installation such as a book case unless proper
ventilation is provided.
Never push objects of any kind into this projector
through cabinet slots as they may touch dangerous
voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on
the projector.
Do not overload wall outlets and extension cords as
this can result in fire or electric shock. Do not allow
anything to rest on the power cord. Do not locate this
projector where the cord may be damaged by persons
walking on it.
Do not attempt to service this projector yourself as
opening or removing Covers may expose you to
dangerous voltage or other hazards. Refer all
servicing to qualified service personnel.
Unplug this projector from wall outlet and refer
servicing to qualified service personnel under the
following conditions:
a. When the power cord or plug is damaged or
frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally by
following the operating instructions. Adjust only
those controls that are covered by the operating
instructions as improper adjustment of other
controls may result in damage and will often
require extensive work by a qualified technician to
restore the projector to normal operation.
e. If the projector has been dropped or the cabinet
has been damaged.
f. When the projector exhibits a distinct change in
performance-this indicates a need for service.
When replacement parts are required, be sure the
service technician has used replacement parts
specified by the manufacturer that have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or injury
to persons.
Upon completion of any service or repairs to this
projector, ask the service technician to perform routine
safety checks to determine that the projector is in safe
operating condition.
Information for users in the European Union
This is a device to project images onto a screen,etc., and is
not intended for use as indoor lighting in a domestic environment.
Directive 2009/125/EC.
NOTE FOR CUSTOMERS IN THE US
Hg LAMP(S) INSIDE THIS PRODUCT CONTAIN
MERCURY AND MUST BE RECYCLED OR DISPOSED OF
ACCORDING TO LOCAL STATE OR FEDERAL LAWS.
5
Safety Guide
Air circulation
Installing the projector properly
Vents in the cabinet are provided for ventilation.
To ensure reliable operation of the product and
to protect it from overheating, these openings
must not be blocked or covered.
Please set the projector on nearly-level.
Be sure to install the projector properly.
Improper installation may reduce the lamp
lifetime and even cause a fire hazard.
Do not roll the projector over 10o
from side to side.
Caution
Hot air is exhausted from the exhaust vent.
When using or installing the projector, the
following precautions should be taken.
- Do not put any flammable objects, or spray
can near the projector. Hot air is exhausted
from the air vents.
- Keep the exhaust vent at least 1m away from
any objects.
- Do not touch a peripheral part of the exhaust
vent, especially screws and metallic part. This
area will become hot while the projector is
being used.
- Do not put anything on the projector. Objects
put on the cabinet will not only get damaged
but also may cause fire hazard by heat.
- Cooling fans are provided to cool down the
projector.
- The fan’s running speed is changed according
to the temperature inside the projector.
(
Do not pitch the projector more
than 10o backward and forward.
Do not point the projector up to
project an image.
Do not point the projector down
to project an image.
Do not put the projector on either
side to project an image.
Caution in ceiling installation the projector
-Only qualified personal is authorized for ceiling
installation.
-We are not responsible for the hurt and damage
caused by ceiling bracket that purchased from
unauthorized dealer even in warranty period.
-Remove the ceiling bracket immediately while
not use.
-While installing, torque screwdriver is suggested,
don't use electric or impact-type screwdriver.
-Please read the manual of bracket for details.
Air Intake Vent
Exhaust Vent
M4x10
10mm
Torque:1.40N.m
Air Intake Vent
6
Safety Guide
Moving the projector
When moving the projector, take care of the
lens and retract the adjustable feet to prevent
damage to the lens and cabinet.
Notes on Lens Protective Ring
Before operating the projector, remove the lens
protective ring. In case of transportation, rotate
the FOCUS ring and LENS SHIFT lever to let
the lens back to its central position and put on
the lens protective ring to protect the lens.
ZOOM
FOCUS
Notes on Projector Handling
When lifting or moving the projector, do not
hold the lens and the peripheral part to prevent
damage on the lens or projector.
Be careful in handling the projector. Do not
drop or bump it to avoid strong force, or place
other objects on the cabinet.
Note:
The lens of the projector is manual.
When operating the projector, pay
attention to the following conditions.
● When the lens is rotating, do not
touch it, otherwise your fingers may
get hurt.
● Do not allow a child to touch the lens.
LENS SHIFT
Caution in moving or transporting the
projector
Do not hold the lens and the peripheral part.
– Do not drop or bump the projector, otherwise
damages or malfunctions may result.
– When carrying the projector, use a suitable
carrying case.
– Do not transport the projector by courier or
any other transport service in an unsuitable
transport case. This may cause damage
to the projector. For more information about
transporting the projector by courier or any
other transport service, consult your dealer.
– Do not put the projector in a case before it is
cooled enough.
7
Compliance
FCC Caution
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
Use of shielded cable is required to comply with class B limits in Subpart B of Part 15 of FCC Rules.
Do not make any changes or modifications to the equipment unless otherwise specified in the
instructions. If such changes or modifications should be made, you could be required to stop operation of
the equipment.
Model Number : LC-XBS500, LC-WBS500
Trade Name : EIKI
Responsible party : EIKI International,Inc.
Address : 30251 Esperanza Rancho Santa Margarita CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL)
and certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit
into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into
the outlet, contact your electrician.
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the
pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be
used of the same rating, marked thus
. If the fuse cover is detachable, never use the plug with the
cover omitted. If a replacement fuse cover is required, ensure it is of the same colour as that visible on
the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department
indicated in your User Instructions.
If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed.
The end of the flexible cord should be suitably prepared and the correct plug fitted.
WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE
SOCKET OUTLET.
The Wires in this mains lead are coloured in accordance with the following code:
Green-and-yellow . . . . . . . . . Earth
Blue . . . . . . . . . . . . . . . . .
Neutral
Brown . . . . . . . . . . . . . . . .
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured
markings identifying the terminals in your plug proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
The wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
WARNING: THIS APPARATUS MUST BE EARTHED.
ASA
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE.
8
Accessories
Owner's Manual(CD)
AC Power cord
Remote control with batteries
(AA or LR6)
VGA cable
Quick start guide
Lens Protection Ring
9
Part names and functions
Front
④ ③
⑤
⑥
②①
⑦
Back
① Indicators
② Remote control receiver(front)
③ Lamp cover
④ Lens shift
⑤ Top control panel
⑥ Filter
⑦ Projector Lens
⑧ Air Intake Vent
⑧
⑨ AC cord connector
⑩ Terminals
⑪ Remote control receiver(back)
⑨
⑩
⑪
Bottom
⑬ Adjustable feet
⑭ Exhaust vent
Caution
Hot air is exhausted from the exhaust vent. Do
not put heat-sensitive objects near this side.
⑭
10
⑬
Part names and functions
Terminals
①
②
VGA IN 1 / YCbCr / S-VIDEO IN
③
④
VGA IN 2 / VGA OUT
⑤
⑥
⑦
LAN
USB-B
USB-A
HDMI
RS-232C
⑧
① DC OUT
DC out 12V 1.5A .
② VGA IN 1/YCbCr/S-VIDEO IN
This is the terminal to input RGB, YCbCr or
S-video signals.
③ VGA IN 2/VGA OUT
- Connect a computer output to this terminal.
- Output the analog signal form ② to other
monitor.
④ HDMI
This is the terminal to input HDMI signals.
⑤ LAN
This is the LAN terminal to connect to the
network.
⑥ USB-B
This terminal is used to connect the
projector to the computer with a USB cable
when you want to use the "USB Display"
function.
⑦ USB-A
When using the "Memory Viewer" function,
insert the USB memory directly to this
terminal.
R/C
AUDIO OUT AUDIO IN
⑨ ⑩ ⑪
AUDIO IN
R
L
(MONO)
⑫
VIDEO IN
⑬ ⑭
⑧ RS-232C
When using RS232 to control the projector,
please connect the serial control line to this
terminal.
⑨ R/C
Connect the wired remote control cable to
this jack while operation the projector by
wired remote control.
⑩ AUDIO OUT
Connect external audio amplifier to this jack.
⑪ AUDIO IN
This is the terminal to input computer audio
signals.
⑫ MONO(R/L)
For a mono audio signal (a single audio
jack), connect it to MONO(R/L) jack.
⑬ VIDEO IN
This is the terminal to input video signals.
⑭ Remote Control receiver(BACK)
Operation the projector by remote control.
11
Part names and functions
Top control and Indicators
①
③
②
④
⑨
⑩
⑪
⑫
⑤
⑥
⑦
⑧
① POWER
Turn on/off the projector.
⑨ Remote Control receiver(Front)
Operation the projector by remote control.
② ▲▼◄►/UP/DOWN/VOL+/VOL- Select an item or adjust the value in the
screen menu.
- Pan the image in the D. Zoom +/- mode.
- Increase or decrease volume.
⑩ POWER
- It lights red when the projector is in standby mode.
- It lights green during normal operations.
- It flashes green in the Power management
mode.
- It flashes red during fans cooling.
③ MENU
Open or close the screen menu.
④ ESC
Return to the previous menu.
⑤ AUTO
Perform various settings configured
automatically, including the "Input search" ,
"Auto PC adj." and "Auto keystone".
⑥ OK
- Enter menu operation.
- Execute the selected item.
⑦ INPUT
Select an input source.
⑧ KEYSTONE
Correct the keystone distortion.
12
⑪ LAMP
- It turns yellow when the life of the projection
lamp draws to an end.
⑫ WARNING
- It flashes red when the internal projector
temperature is beyond the operating
temperature range.
- It lights red when the power supply of the
projector is abnormal.
Part names and functions
Remote control
②
*
④ VIDEO
Select "Video" as input source.
①
⑤ NETWORK
Select "Network" as input source.
④
③
⑤
⑦
⑥
⑧
⑩
⑨
⑪
⑫
⑬
⑮
⑭
⑥ VGA IN 1
Select "Computer 1" as input source.
⑦ S-VIDEO
Select "S-video" as input source.
⑧ USB DISPLAY
Select "USB Display" as input source.
⑨ VGA IN 2
Select "Computer 2" as input source.
Note:
- It only can switch input source to "Computer 2"
when select VGA IN2/VGA OUT as VGA IN2.
⑩ COMPONENT
Select "Component" as input source.
* Laser Transmitting Window:
Laser beam will emit from this window. While
pressing LASER button during the projection
to use the remote control as a laser pointer.
Do not stare directly at the laser transmitting
window or aim the window at human body to
avoid any physical injury.
① POWER
Turn on or turn off the projector.
② LASER
Press this button during projection, the
remote control can be used as a laser
pointer.
③ HDMI
Select “HDMI” as input source.
⑪ MEMORY VIEWER
Select "Memory Viewer" as input
source.
⑫ MENU
Open or close the screen menu.
⑬ AUTO
Enter auto setup adjust mode.
⑭  button
- Select item or adjust data in screen
menu.
- Select the image display area in
digital zoom + mode.
⑮ OK
Enter the menu or select an item in
the menu.
13
Part names and functions
⑲ FREEZE
⑰
⑯
Freeze the projected image.
⑳ TIMER
Enable the timer function.
⑲
⑱
⑳
㉒
㉑
㉓
㉕
㉔
㉖
㉘
㉗
㉙
㉚
㉑ MUTE
Turn off the volume.
㉒ IMAGE
Select the image mode.
㉓ SCREEN
Select the screen size.
㉔ VOLUME +
Increase the volume.
㉕ LAMP
Select the lamp mode.
㉖ D.ZOOM +
Digital zoom in the image.
㉛
㉗ VOLUME Decrease the volume.
㉘ PATTERN
Set the internal test image.
㉙ D..ZOOM ⑯ ESC
Return to the previous menu.
⑰ KEYSTONE
Correct the keystone distortion.
⑱ BLANK
Temporarily close the image on the screen.
14
Digital zoom out the image.
㉚ INFO.
Display the projector information.
㉛ Wired remote control output port
Connect the wired remote control cable to
this port while operation the projector by
wired remote control.
Part names and functions
Install remote control batteries
① Open the battery
cover.
②Install new batteries.
③Put the cover
back.
Two AA batteries
For correct polarity
(+ and –), be sure
battery terminals
are in contact
with pins in the
compartment.
To ensure safe operation, please observe the following precautions:
● Use two (2) AA or LR6 type alkaline batteries.
● Always replace batteries in sets.
● Do not use a new battery with a used battery.
● Avoid contact with water or liquid matter.
● Do not expose the remote control to moisture or heat.
● Do not drop the remote control.
● If the battery has leaked in the remote control, carefully wipe the case clean and
install new batteries.
● Risk of explosion if two batteries are replaced by an incorrect type.
● Dispose of used batteries according to the instructions on the battery or local
regulations or guides.
Operating range
Point the remote control toward the remote
control receivers on the projector (front and
back) when pressing any button.
The maximum operating range for the remote
control is about 5 meters and 60 degrees.
30°
30°
5m
30°
Wired Remote Control Transmitter
5m
30°
The remote control can be used as a wired
remote control. Wired remote control helps you
use the remote control outside of the operation
range (26.25'/8m). Connect the remote control
and the projector with the remote control cable.
Connected with the remote control cable, the
remote control does not emit wireless signal.
15
Installation
Positioning the projector
Note:
● The brightness in a room has a great influence on picture quality. It is recommended to limit the
ambient lighting in order to get the best image.
● All measurements are approximate and may vary from the actual sizes.
LC-XBS500:
4:3
(Diagonal:Inch)
15.171m(18.943m)
9.180m(11.466m)
6.107m(7.631m)
Min.
Max.
4.570m(5.713m)
3.034m(3.796m)
(Diagonal:Inch)
15.171m(18.943m)
0.882m(1.111m)
9.180m(11.466m)
30”
6.107m(7.631m)
(Center)
3.034m(3.796m)
0.882m(1.111m)
Note:
30”
The data in "()" is the project distance for
16:9 aspect ratio.
(Center)
(Diagonal:Inch)
16.086m(18.943m)
30"
100"
150"
200"
300"
610x457 2032x1524 3048x2286 4064x3048 6096x4572
0.882m
1.482m
3.034m
5.031m
30"
100"
4.570m 6.107m 9.180m
7.566m 10.101m 15.171m
Min.
Max.
4.570m(5.713m)
Screen size
(WxH)mm
4:3 aspect
ratio
Maximum
Minimum
16:9
Screen size
(WxH)mm
16:9 aspect
ratio
Maximum
Minimum
150"
200"
300"
664x374 2214x1245 3321x1868 4428x2491 6641x3736
1.111m
1.859m
3.796m
6.288m
5.713m 7.631m 11.466m
9.452m 12.616m 18.943m
9.735 m(11.466m)
LC-WBS500:
6.477 m(7.631m)
Max.
Min.
4.848m(5.713m)
3.219m(3.796m)
16.086m(18.943m)
(Diagonal:Inch)
0.938 m(1.111m)
9.735 m(11.466m)
30”
6.477 m(7.631m)
4.848m(5.713m)
Max.
Min.
(Center)
3.219m(3.796m)
0.938 m(1.111m)
30”
(Center)
Note:
The data in "()" is the project distance for
16:9 aspect ratio.
16:10
Screen size
30"
100"
150"
200"
300"
(WxH)mm
16:10 aspect 646x404 2154x1346 3231x2019 4308x2692 6462x4039
ratio
Maximum
0.938m 3.219m 4.848m 6.477m 9.735m
Minimum
1.573m 5.336m 8.023m 10.711m 16.086m
16:9
Screen size
(WxH)mm
16:9 aspect
ratio
Maximum
Minimum
30"
100"
150"
16
300"
664x374 2214x1245 3321x1868 4428x2491 6641x3736
1.111m
1.859m
3.796m
6.288m
5.713m 7.631m 11.466m
9.452m 12.616m 18.943m
Adjustable foot
The projector can be adjusted up to 40 mm
with the adjustable feet.
Rotate the adjustable feet to lift the projector
to a certain height. During lifting, rotate the two
feet clockwise.
To lower or retract the adjustable feet, rotate
the two feet counterclockwise.
Keystone distortion of projected images can
be corrected by auto settings, remote control
operation or menu operation.
200"
Adjustable feet
Installation
Lens shift adjustment
Projection lens can be moved from side to side and up to down.
This function makes the positioning of images easy on the screen.
The display position can be shifted upward up
to 40%(XGA), 50%(WXGA) elevation of the
display.
The display position can be shifted downward
up to 40%(XGA), 50%(WXGA) elevation of the
display.
When the lens is shifted to top.
When the lens is shifted to bottom.
The display position can be shifted to the left
up to 10% width of the display.
The display position can be shifted to the right
up to 10% width of the display.
When the lens is shifted to leftmost.
When the lens is shifted to rightmost.
a
b
a: 40%(LC-XBS500)
50%(LC-WBS500)
b: 10%(LC-XBS500)
10%(LC-WBS500)
When the lens is
shifted to the center.
Shifting range
17
Installation
Connecting to computer (Digital and analog RGB)
Cables used for connection:
● VGA cable
● HDMI cable*
(*=Cables are not supplied with the projector)
RS232 output
Serial
cable
(Cross)
RS232 input
VGA output
VGA
cable
VGA input
VGA IN 1 / YCbCr / S-VIDEO IN
● Serial cable*
VGA input/output
VGA
cable
HDMI output
HDMI
cable
VGA output/input
HDMI input
VGA IN 2 / VGA OUT
HDMI
RS-232C
R/C
USB-B
LAN
AUDIO OUT AUDIO IN
USB-A
AUDIO IN
R
L
(MONO)
VIDEO IN
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting the cables.
18
Installation
Connecting to video equipment (Video, S-Video)
Cables used for connection:
● S-video cable**
● Component conversion cable*
● Video cable*
(*=Cables are not supplied with the projector)
(**=Dedicated cable is reguired and can be ordered through your dealer)
S-video output Component output
S-video
cable
Video output
Video
cable
Component
conversion cable
Video input
S-video input Component input
VGA IN 1 / YCbCr / S-VIDEO IN
VGA IN 2 / VGA OUT
HDMI
RS-232C
R/C
USB-B
LAN
AUDIO OUT AUDIO IN
USB-A
AUDIO IN
R
L
(MONO)
VIDEO IN
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting the cables.
19
Installation
Connecting to audio equipment
Cables used for connection:
● Audio cable*
(*=Cables are not supplied with the projector)
External audio equipment
Audio input
Audio output
Audio output
(R) (L)
Audio cable
(stereo)
Audio cable
(stereo)
Audio
cable
Audio input
Audio output
Note: The left and right
channels are combined
when there is only the
L(mono) is inserted.
(R) (L)
Audio input
VGA IN 1 / YCbCr / S-VIDEO IN
VGA IN 2 / VGA OUT
HDMI
RS-232C
R/C
USB-B
LAN
AUDIO OUT AUDIO IN
USB-A
AUDIO IN
R
L
(MONO)
VIDEO IN
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting the cables.
20
Installation
Connecting to USB device (USB-A, USB-B)
Cables used for connection:
● USB-B cable*
(*=Cables are not supplied with the projector)
USB-A output
USB-B
cable
USB-A device
USB-B input
VGA IN 1 / YCbCr / S-VIDEO IN
VGA IN 2 / VGA OUT
LAN
HDMI
RS-232C
R/C
AUDIO OUT AUDIO IN
USB-B
USB-A
AUDIO IN
R
L
(MONO)
VIDEO IN
Unplug the power cords of both the projector and external equipment from the AC outlet
before connecting the cables.
21
Installation
Connecting the AC power cord
This projector uses nominal input voltages of
100–240V AC and it automatically applies to
different input voltages. It is designed to work
with a single-phase power system having a
grounded neutral conductor. To reduce the risk
of electrical shock, do not plug into any other
type of power system. If you are not sure of
the type of power being supplied, consult your
authorized dealer or service station. Connect
the projector with all peripheral equipment
before turning it on.
Connect the AC power cord
(supplied) to the projector.
Note:
The AC outlet should be near this equipment
and must be easily accessible.
Note:
For safety, unplug the AC power cord when the projector is not in use. When the projector is
connected to an outlet with AC power cord, it is in stand-by mode and consumes a little electric
power.
Note on the power cord
AC power cord must meet the requirements of the country where you use the projector. Confirm the AC
plug type with the chart below and proper AC power cord must be used. If the supplied AC power cord
does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For the U.S.A. and
Canada
For Continental
Europe
Ground
To power cord
connector on your
projector.
To the AC outlet.
For the U.K.
Ground
To the AC outlet.
To the AC outlet.
Note:
● Using incorrect power cord may influence the product performance, or even cause hazards like an
electric shock or fire. To ensure the product performance and security, please apply the cable of the
same model with the original one.
22
Basic operation
Turn on the projector
1. Complete peripheral connections (with a
computer, VCR,etc.) before turning on the
projector.
16
2. Connect the projector’s AC power cord into
the AC outlet. The POWER indicator turns
red.
3. Press the POWER button on the top control
or on the remote control. The POWER
indicator becomes green and the cooling
fans start to work. The preparation display
appears on the screen.
4. If the projector is locked with a PIN code, a
PIN code input dialog box appears. Enter
the PIN code as instructed below.
Note:
● When the logo select is set to be "Off", the
logo will not be displayed on the screen.(See
page 49)
Enter a PIN code
Press the OK button, press  button to
select a number, then press the OK button,
select a number and enter it to the PIN code
box, then number changes to "*", automatically
move the cursor to next box. If you fixed an
incorrect number, press MENU button to reset
it again.
Repeat this step to complete entering a threedigit number.
After entering the three-digit number, move the
cursor to "Set", then you can start to operate
the projector.
If you entered an incorrect "PIN code", the
number (***) turn red. PIN code will be reset
within one second automatically, Enter the
correct PIN code all over again.
What is PIN code?
PIN (Personal Identification Number) code is a
security code that allows the person who knows
it to operate the projector. Setting the PIN code
can prevent unauthorized use of the projector.
A PIN code consists of a three-digit number.
Refer to the PIN code lock function in the
"Expand" "Security" menu on page 50 for PIN
code lock operation of the projector.
PIN Code
Set
Cancel
-----
OK
Input PIN code
Esc
Back
Esc
Back
PIN Code
*
Set
Cancel
Move
OK
Select
Move the cursor to "Set", and press "OK".
Caution on handling the PIN code
If you forget your PIN code, the
projector can no longer be started.
Take a special care in setting a
new PIN code. Write down the
number in a column on page 88 of
this manual and keep it properly.
Should the PIN code be missing
or forgotten, consult your dealer or
service center.
23
Basic operation
Turn off the projector
1. Press the POWER button on the top control
or on the remote control, and "Power off?"
appears on the screen.
2. Then, press the POWER button again in 4
seconds. The POWER indicator starts to
flash red, and the cooling fans keep running
(You can select the fan noise and running
speed). Now you can unplug the AC power
cord after the fans stop running. Otherwise,
the service life of the projector will be
affected or the projector will can not be
turned on or turn on abnormal.
3 When the projector has cooled down enough
to be turned on again, the POWER indicator
stops flashing.
To maintain the lamp life, once you turn
the projector on, wait at least 5 minutes
before turning it off.
Do not operate the projector continuously
without reset. Continuous use may result
in shortening the lamp life. Turn off the
projector and let it standby for about an
hour in every 24 hours.
Note:
● When the On start function is “On” , this
projector is turned on automatically by
connecting the AC power cord to an AC outlet .
● The running speed of cooling fans is changed
according to the temperature inside the
projector.
● Do not put the projector in a case before it is
cooled enough.
● If the POWER indicator flashes or emits a
red light, see page 82.
● While the POWER indicator is flashing, the
lamp is being cooled down and the projector
cannot be turned on. Wait until the POWER
indicator turns red to turn on the projector again.
● The fan rotation will terminate directly if the
AC power cord is unplugged immediately
after the projector is turned off.
● The projector can be turned on after the
POWER indicator turns red. The waiting time
to restart will be shortened when the normal
power-off processing for fan cooling is
completed, comparing with the time the AC
power cord is immediately unplugged after the
power-off.
24
Power off ?
“Power off ? ” disappears after 4 seconds.
Basic operation
How to operate the screen menu
The projector can be adjusted or set via the onscreen menu. Each main menu can be divided
into several levels of submenus, and subme
nus are also divided into several levels of subsubmenus.
For each adjustment and setting procedure,
refer to the respective sections in this manual.
Top control
 button MENU button
ESC
button
OK button
Remote control
OK button
MENU
button
 button
Esc
button
1 Press the MENU button on the remote control
or top control to display the screen menu.
2 Press  buttons to select an entry in the main
m
enu and then press the OK button to enter
the submenu.
3 Press buttons to select an item, and then
press the OK button to set or enter the
submenu.
4 Press  buttons to adjust settings or switch
among the items. Press the OK button for
corresponding operation.
Screen menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Auto PC adj.
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Upper right
Background display
Blue
System
----
Move
OK
Select
Exit
5 Press ESC button on the remote control or
top control to go back to the previous menu.
Press MENU button again to exit the screen
menu.
25
Basic operation
Menu bar
Main menu
①
Display
②
Color adjust
③
Setting
④
Expand
⑤
Memory
Viewer
⑥
Info.
Sub menu
Auto PC adj.
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Upper right
Background display
Blue
System
----
Move
OK
Select
Exit
① Display
- Adjust computer parameters to match with VGA input signal format: Auto PC adj., Fine sync,
H Position, V Position and H.Size.
- Aspect: Normal and Wide.
- Project way: select a project way among Front, Rear, Celing/Front and Ceiling/Rear.
- Menu position: set the menu's position on the screen.
- Background display: set the background display color for project screen.
- System: select a system signal format to match the input source.
② Color adjust
- Image mode: the available image modes is Standard, Dynamic, User Image, Colorboard,
Blackboard(Green) or Cinema.
- Image color adjust:
If a computer is selected as a signal source, the following image adjusting options are available:
Contrast, Brightness, Color temp., White balance (R/G/B) and Sharpness.
If video equipment is selected as a signal source, the following image adjusting options are available:
Contrast, Brightness, Color, Tint, White balance (R/G/B) and Sharpness.
③ Setting
Configure basic operation settings of the projector: On start, Standby mode, High land, Lamp control,
Cooling fast, Closed caption, Key lock, Iris, Terminal, Sound and HDMI setup.
④ Expand
Configure expand operation settings of the projector: Language, Auto setup, Keystone, Logo,
Security, Power management, Filter counter, Test Pattern, Network, Remote control, Factory
default and Lamp counter.
⑤ Memory viewer
Configure operation settings for Memory Viewer function: Set Slide, Slide transition effect, Sort
order, Rotate, Best fit, Repeat and Apply.
⑥ Info.
The system information of the projector.
26
Basic operation
Adjust zoom and focus
Rotate the ZOOM to zoom in or zoom out the
image.
FOCUS
ZOOM
Rotate the FOCUS to adjust the focus of the
image.
①
Lens shift adjustment
②
Perform the lens shift adjustment with ① and ② .
Rotate ① , the screen may deviate upand-down from the central axis of lens shift
40%(XGA), 50%(WXGA) elevation of the
display.
Rotate ② , the screen may deviate left-andright from the central axis of lens shift 10%
width of the display.
Auto setup function
This function is available just by pressing
the AUTO button on the remote control or
top control. The system then automatically
performs various settings in the "Expand"
menu, including "Input search", "Auto PC adj."
and "Auto keystone".
Top control
AUTO
button
Remote control
AUTO
button
27
Basic operation
Keystone
If a projected image has keystone distortion,
follow the steps below to manually correct the
keystone distortion.
Top control
Press KEYSTONE button on the top control or
on the remote control. The Keystone screen
will displayed, (it includes: H/V Keystone,
Corner correction, Curved correction and Reset
value), press to select the item.
H/V Keystone.........Adjusts when the horizontal
or vertical trapezoid of the
projected image is distorted.
Corner correction...Adjusts when the four
corners of the projected
image are distorted.
Curved correction...Adjusts when the linearity
is not uniform or the vertical
and horizontal lines are
distorted.
Reset value............Return the corrected values
to the factory default values.

button
KEYSTONE
button


● The arrows are white when there is no correction.
● The arrows that are used for correction turns red.
● Press  button long time, the arrows
turn red and can be adjusted quickly
● The arrows disappear at the maximum correction.
● If you press the KEYSTONE button on the
remote control or top control once again while
the keystone dialog box is being displayed,
the keystone adjustment is canceled.
● The adjustable range can be limited depending
on the input signal.
28
Remote control


H/V Keystone
KEYSTONE
button
H/V Keystone
Corner correction
Curved correction
Reset value
Basic operation
Volume
Direct operation
Top control
Volume
Press the VOLUME +/- buttons on the remote
control or top control to adjust the volume.
Mute
Press the MUTE button on the remote control
and select "On" to turn off the audio temporarily.
To restore the audio to its previous level, press
the MUTE button again and select "Off" or press
the VOLUME+/– buttons.
Mute function is also effective for AUDIO OUT
jack.
VOLUME +/- button
Remote control
MENU
button
VOLUME +/button
Menu operation
1 Press the MENU button to display the screen
menu. Press  button to select the "Setting"
menu icon. Press the OK button to enter the
submenu entry.
Volume menu
Display
On Start
Off
Standby mode
Normal
High land
2 Press  button to select "Sound" and then
press the OK button.
Color adjust
3 Press  button to select "Volume" or "Mute"
to adjust.
Expand
Key lock
Memory
Viewer
Iris
Off
Lamp control
Setting
Cooling fast
Normal
Closed caption
Volume
Press  to increase the volume and  to
decrease the volume.
Info.
Off
Off
Terminal
Computer 2
Sound
...
HDMI setup
Move
OK
Select
Esc
Back
Mute
Press  button to switch the mute function
(On/Off).
4 Press the OK button to select.
29
Basic operation
Remote control operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the
buttons enables you to quickly without calling up the screen menu.
FREEZE button
Press FREEZE button on the remote control,
video will be paused and the audio is muted.
The icon is displayed on the screen during
Freeze. Press FREEZE button again, the video
playback resumes and the audio is unmuted.
Remote control
MUTE button
Press MUTE button on the remote control to
turn off the volume. Press MUTE button again or
VOLUME+/- button to cancel mute function.
VOLUME +/- button
Press VOLUME +/- button on the remote control
to increase or decrease the volume.
FREEZE
IMAGE button
Press IMAGE button on the remote control to
select the image mode you want.
MUTE
IMAGE
LAMP
VOLUME +/INFO
LAMP button
Press LAMP button to select a lamp mode to
change the brightness of the screen.
Normal ..Normal brightness.
ECO ..... Lower brightness, reducing the
lamp power consumption and
extending the lamp life.
INFO button
Press INFO button on the remote control to
display the projector information.
Note:
See the next page for the description of other
buttons.
30
Basic operation
ESC button
Return to the previous menu.
BLANK button
Press BLANK button on the remote control
to black out the image. To restore to normal,
press the BLANK button again or press any
other button.
The screen changes each time you press the
button as follows:
Black out →Normal →Black out →Normal ...
TIMER button
Press TIMER button. The timer display “00:00”
appears on the screen and the timer starts to
count time (00:00–59:59).
To stop the Timer, press TIMER button. Press
TIMER button again, and then the Timer display
disappears.
SCREEN button
Press SCREEN button on the remote control to
select the screen size you want.
Blank
Image
Blank
“Blank” disappears after 2 seconds if there is
no other button operation.
02 :02
Timer display
Remote control
D.ZOOM+ button
Press D.ZOOM+ button, the on-screen menu
will disappear, while the information on digital
zoom + appears.
Press ▲▼◄►to move the image horizontally
and vertically.
The moving is effective only when the image is
larger than the size of the screen.
D.ZOOM- button
Press D.ZOOM- button, the on-screen menu
will disappear, while the information on digital
zoom - appears.
To exit the “digital zoom +/-“mode, press any
button except the D.ZOOM+/- .
ESC
BLANK
TIMER
SCREEN
D.ZOOM +
D.ZOOM -
To return to normal size, select “ SCREEN”
button on the remote control to adjust screen
size, or press  button to move the
image horizontally or vertically.
31
Basic operation
Input select
Direct Operation
Press VGA IN 1, VGA IN 2, HDMI, Component,
Video, S-video, Network, Memory Viewer or
USB Display on the remote control as input
source.
Menu operation
1 Press INPUT button on the top control to
display the input select menu.
Remote control
VIDEO
S-VIDEO
HDMI
VGA IN 1
VGA IN 2
COMPONENT
2 Press  button to select Computer 1,
Computer 2, HDMI, Component, Video, S-video,
Network, Memory Viewer or USB Display,
then press the OK button.
Computer 1
Computer 2
HDMI
Component
Video
S-video
When input source is from
computer connected to VGA
IN 1 terminal with VGA cable,
please select "Computer 1".
Top control
When input source is from
computer connected to VGA IN
2/VGA OUT terminal with VGA
cable, please select "Computer
2".
When input source is from
equipment connected to HDMI
terminal with HDMI cable,
please select "HDMI".
Select it when the input source
is from the video equipment
connected to YCbCr terminal.
INPUT button
Input select menu

Computer 1
Computer 2
HDMI
Component
Video
S-video
Network
Memory Viewer
USB Display
Select it when the video input
signal is connected to VIDEO
IN terminal.
Select it when the video input
signal is connected to S-VIDEO
IN terminal.
Note:
- When the "Input search" function is set to "On" in the "Auto setup" function, press AUTO button,
the input signal will be searched automatically.
- When VGA IN 2/VGA OUT terminal is used as VGA OUT, Computer 2 can not be selected.
32
Basic operation
Input select
Direct Operation
Press VGA IN 1, VGA IN 2, HDMI, Component,
Video, S-video, Network, Memory Viewer or
USB Display on the remote control as input
source.
Remote control
NETWORK
USB DISPLAY
MEMORY VIEWER
Menu operation
1 Press INPUT button on the top control to
display the input select menu.
2 Press  button to select Computer 1
Computer 2, HDMI, Component, Video,
S-video, Network, Memory Viewer or USB
Display, then press the OK button.
Network
Memory Viewer
USB Display
Top control
When input source is from
network connected to LAN
terminal with LAN cable, please
select "Network".
When input source is from
device connected to USB-A
terminal, please select "Memory
Viewer".
When input source is from
device connected to USB-B
terminal, please select "USB
Display".
INPUT button
Input select menu

Computer 1
Computer 2
HDMI
Component
Video
S-video
Network
Memory Viewer
USB Display
Note:
- When the "Input search" function is set to "On" in the "Auto setup" function, press AUTO button,
the input signal will be searched automatically.
- When signal is in "USB Display","Memory Viewer" and "Network", FREEZE, ASPECT, IMAGE,
AUTO SETUP and SCREEN function cannot work.
- Memory Viewer function, please refer to page 67~68.
- USB Display function, please refer to page 69~70.
33
Display
Auto PC adj.
Auto PC Adjustment function is provided to automatically adjust Fine sync, Horizontal, Vertical and H.Size
to conform to your computer.
Menu operation
Auto PC adj.
1. Press MENU button on the remote control
or top control to display screen menu.
Press  button to select "Display", then
press the OK button.
2. Press  button to select "Auto PC adj.",
then press the OK button. "Please wait" will
be displayed on the screen, the Auto PC adj.
function will be executed.
Auto PC adj. Menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Auto PC adj.
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
You can cut off flicker from the image displayed
by pressing  to adjust the value.(from 0 to
31).
H Position
Press  to adjust the horizontal image
position.
V Position
Press  to adjust the vertical image position.
H.Size
This function is used to adjust and minimize
the effect of interference caused by projection
of patterns consisting of vertical stripes.
The projection of the vertical striped pattern
may cause cyclic patterns (noise). Adjust to
minimize the amount of interference.(From -15
to +15).
H.Size must be set before adjust Fine sync.
√ Note:
The adjustment of Fine sync, H Position, V
Position and H.Size is only for computer
signal input.
34
Upper right
Background display
Blue
System
----
Move
Fine sync
Front
Menu position
OK
Select
Exit
Note:
- The projector executes the Auto PC adj.
automatically when the computer signals input
the projector for the first time.
- Automatic adjustment may not work depending
on the model of the computer and the input
signal.
- The Auto PC adj. cannot be operated when
480i, 576i, 480p, 576p, 720p 1080i or 1080p is
selected in the "Display" menu → "System",
or when the signal is coming from the HDMI
terminal.
Display
Aspect
You can set a screen size to fit the image while
maintaining the aspect ratio of the input signal.
1. Press  to select "Aspect" and then
press the OK button.
2. Press  button to select the item, then
press the OK button.
Normal... Projects the image at the maximum
size while maintaining the aspect
ratio of the input signal.
Wide.... Projects the image at 16:9 aspect ratio.
Aspect menu
Auto PC adj.
Display
Color adjust
Memory
Viewer
Info.
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Setting
Expand
Fine sync
Project way
Front
Menu position
Upper right
Background display
Blue
System
----
Adjust
OK
Select
Esc
Back
Project Way
This function is used to set the project way.
1 Press MENU button on the remote control
to display screen menu. Press  button to
select "Display", then press the OK button.
2 Press button to select "Project way",
press the OK button.
3 Press button to select the item you want
to set, press the OK button.
Front ........ Projects to front screen when
projector is front standing.
Rear ........ Projects to rear screen when
projector is front standing.
Ceiling/Front ..... Projects to front screen when
projector is in ceiling state.
Ceiling/Rear ..... Projects to rear screen when
projector is in ceiling state.
Menu Position
This function is used to change the position of
screen menu.
1 Press MENU button on the remote control
to display screen menu. Press  button to
select "Display", then press the OK button.
2 Press button to select "Menu position",
press the OK button.
3 Press button to select the item you want
to set, press the OK button.
Upper left .... Menu locates on upper left of
the screen.
Upper right .. Menu locates on upper right of
the screen.
Center ......... Menu locates at the center of
the screen.
Lower left .... Menu locates on lower left of
the screen.
Lower right .. Menu locates on lower right of
the screen.
Project way menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Auto PC adj.
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Upper right
Background display
Blue
System
----
Adjust
OK
Select
Esc
Back
Menu position
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Auto PC adj.
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Upper right
Background display
Blue
System
----
Adjust
OK
Select
Esc
Back
35
Display
Background Display
This function is used to select the screen
background of the projector when there is no
signal detected.
1 Press MENU button on the remote control
or top control to display screen menu. Press
 button to select "Display", then press
the OK button.
2 Press  button to select "Background
display", press the OK button.
3 Press  button to select the item you want
to set, press the OK button.
Background display
Auto PC adj.
Display
Color adjust
Setting
Expand
Fine sync
0
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Memory
Viewer
Info.
Upper right
Background display
Blue
System
----
Adjust
OK
Select
Esc
Back
Black .... Select black background.
Blue ...... Select blue background.
System
Computer system select
The projector automatically tunes to various types of computers with its function of Multi-scan
system and Auto PC Adjustment. If a computer is selected as a signal source, the projector
automatically detects the signal format and tunes to project proper images without any additional
setting.
One of the following messages may appear
when:
Auto
-----
36
When the projector cannot recognize
the connected signal conforming to
the provided computer system, Auto
is displayed on the System menu
box and the Auto PC Adj. function
works to display proper images. If
the image is not projected properly,
a manual adjustment is required.
There is no signal input from computer.
Check the connection between your
computer and projector.
System menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Auto PC adj.
Fine sync
25
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Front
Menu position
Upper right
Background display
Blue
System
Adjust
System
1280x1024, 60Hz
OK
Select
Esc
Back
Display
Select computer system manually
The system can also be selected manually.
1 Press MENU button on the remote control or
on top control to display the screen menu.
Press  button to select the "Display" icon,
and press the OK button.
2 Press  button to select "System" and
press the OK button.
3 Press  button to select your required
system, and then press the OK button.
System menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Note:
Auto PC adj.
Fine sync
25
H Position
0
V Position
0
H.Size
0
Aspect
Normal
Project way
Upper right
Background display
Blue
System
Adjust
When HDMI is selected, System menu for
computer is disable.
Front
Menu position
1280x1024, 60Hz
OK
Select
Esc
Back
Esc
Back
Esc
Back
System
System for computer signal
Display
Color adjust
Setting
System
 1280 x 1024, 60Hz
-------------
Expand
----
Memory
Viewer
Info.
Move
Video or S-video
Auto
The projector automatically detects an
incoming video system,and adjusts itself to
optimize its performance. When Video System
is PAL-M, PAL-N or PAL60, select the system
manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N/
PAL60
If the projector cannot reproduce proper video
images, select a specific broadcast signal
format from PAL, SECAM, NTSC, NTSC 4.43,
PAL-M, PAL-N and PAL60.
OK
Select
System for Video or S-video signal
Display
Color adjust
Setting
System
 AUTO
PAL
SECAM
NTSC
NESC4.43
Expand
PAL-M
Memory
Viewer
PAL-N
PAL60
Info.
Move
OK
Select
37
Color adjust
Color adjust menu is used to set the image mode and adjust the image.
Image Mode
Remote control
Direct operation
Press IMAGE button on the remote control to
select the image mode.
Menu operation
1 Press MENU button on the remote control or
top control to display screen menu. Press
 button to select "Color adjust" menu,
then press the OK button.
2 Press button to select "Image mode",
press the OK button.
3 Press button to select the item you want
to set, press the OK button.
Dynamic
The light output is maximized for use in bright
areas.
Standard
The picture becomes suitable for moving
images in general.
Cinema
For watching movies with multiple gray scale
levels.
Blackboard (Green)
For viewing the image projected on a
blackboard (green) by enhancing the image
quality. This is mainly effective on a green
colored board instead of a black colored board.
Colorboard
For images projected onto a red, blue, yellow,
or green wallpaper.
User Image
Image quality preset by the user in the Image
adjustment menu.
38
IMAGE
button
Image mode (Computer)
Display
Color adjust
Setting
Expand
Memory
Viewer
Image mode
Dynamic
Contrast
32
Brightness
32
Color temp.
Mid
Red
32
Green
32
Blue
32
Sharpness
8
Info.
Adjust
OK
Select
Esc
Back
Color adjust
Color adjust (Computer)
1 Press MENU button on the remote control or
top control to display screen menu. Press
 button to select "Color adjust", then
press the OK button.
2 Press button to select the item you want
to set, press the OK button.
3 Press button to adjust the data.
Contrast
Press  to decrease the contrast and  to
increase it.
Brightness
Press  to decrease the brightness and  to
increase it.
Color adjust (Computer)
Display
Color adjust
Setting
Expand
Memory
Viewer
Image mode
User Image
Contrast
32
Brightness
32
Color temp.
Mid
Red
32
Green
32
Blue
32
Sharpness
8
Info.
Move
OK
Select
Exit
Color temp.
Press to select color temperature.( Low,
Mid and High )
Red (White balance)
Press  to lighten the red tone and  to
deepen it.
Green (White balance)
Press  to lighten the green tone and  to
deepen it.
Blue (White balance)
Press  to lighten the blue tone and  to
deepen it.
Sharpness
Press  to decrease the sharpness of the
image and  to increase it.
√ Note:
- If you only adjust projector to "Video", "S-video"
or "Component" , "Sharpness" is disable.
39
Color adjust
Color adjust (Video,S-video,Component)
1 Press MENU button on the remote control or
top control to display screen menu. Press
 button to select "Color adjust", then
press the OK button.
2 Press button to select the item you want
to set, press the OK button.
3 Press button to adjust the data.
Contrast
Press  to decrease the contrast and  to
increase it.
Brightness
Press  to decrease the brightness and  to
increase it.
Color
Press  to decrease the chroma and  to
increase it.
Tint
Press  to select the appropriate tone for
the image.
Red (White balance)
Press  to lighten the red tone and  to
deepen it.
Green (White balance)
Press  to lighten the green tone and  to
deepen it.
Blue (White balance)
Press  to lighten the blue tone and  to
deepen it.
Sharpness
Press  to decrease the sharpness of an
image and  to increase it.
√ Note:
- Signal input "Video", "S-video" or "Component",
"Tint" is in grey, it is disable.
- If you only adjust projector to "Video", "S-video"
or "Component" , "Sharpness" is disable.
40
Color adjust (Video,S-video, Component)
Display
Color adjust
Setting
Expand
Memory
Viewer
Image mode
User Image
Contrast
32
Brightness
32
Color
32
Tint
32
Red
32
Green
32
Blue
32
Sharpness
8
Info.
Move
OK
Select
Exit
Setting
The projector has "Setting" menu that allows you to set the other various functions described as
follows.
1 Press MENU button on the remote control or
Setting menu
top control to display screen menu. Press
 button to select "Setting", then press
On start
Off
Display
Standby mode
Normal
the OK button.
High land
Off
Color adjust
2 Press button to select the item you
Lamp control
want to set, press the OK button.
Cooling fast
Normal
Setting
3 Press button to adjust the item, then
Closed caption
Off
Expand
Key lock
press the OK button.
Memory
Viewer
Info.
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Move
On start
Enable the projector to be turned on
automatically just by connecting the AC power
cord to an outlet when this function is set to
On.
On .......... Start the projection immediately,
enter countdown display.
Off .......... Start up in the standby mode.
OK
Select
Exit
On start
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Standby mode
This function is available when operating the
projector via network.
Press button to select the item below:
Eco.......... Restrict some functions in the
standby mode to reduce power
consumption. In this case, you
cannot use network functions and
some RS-232C commands.
Normal ... Do not restrict network function
and serial communication function
even in the standby mode.
OK
Select
Esc
Back
Standby mode
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
OK
Select
Esc
Back
41
Setting
High land
Enable to control the fan through the Setting
menu.
You can select the running speed of the fan
according to the altitude of the location where
the projector is installed.
Off ...... Normal speed. Set it so if the projector
is operated at a lower altitude.
On ...... Faster than Off. Set it so if the projector
is operated at a higher altitude because
fans will produce weaker effects.
High land
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Change the brightness of the screen.
Normal .... Normal brightness.
Eco .......... Lower brightness, reducing
power consumption and
extending the lamp life.
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Note:
Please set High land "On" when operating the
projector higher than 1400 meters.
Lamp control
Off
Standby mode
OK
Select
Esc
Back
Lamp control
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Cooling fast
This function provides the following options in
the cooling fans' operation after turning off the
projector.
Normal... Normal cooling speed.
60 sec ... Faster and lounder than Normal,
cooling time is shorter.
0 sec ..... Enable you directly unplug the AC
power cord after turning off the
projector, no need waiting for cooling.
OK
Select
Esc
Back
Cooling fast
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
OK
Select
Esc
Back
Note:
When it is set to "0 sec", you cannot restart the projector immediately after the power-off. The
lamp remains high temperature and needs to be cooled, so it takes longer time than
usual for the lamp to light up again.
42
Setting
Closed Caption
Allows the subtitle to be displayed for the
audio contents or other information. If the input
source contains closed caption, you can enable
this function and change the channel. Press
 to select Off, CC1, CC2, CC3 or CC4.
Note:
- The icon of Closed Caption is displayed in
grey when it is disable.
- Closed caption is disable when screen menu
or Timer displayed on screen.
Closed Caption
Display
Color adjust
Setting
On start
This function allows you to use the Key lock to
set the security for the projector operation.
Select "Key lock" and press the OK button,
then press  button to select the item you
want.
Off ............... Unlock.
Projector ...... Lock the operation of
the top control. To
unlock, use the remote
control.
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Expand
Memory
Viewer
Info.
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Key lock
Off
Standby mode
OK
Select
Esc
Back
Key lock
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
OK
Select
Esc
Back
Remote Control ..... Lock the operation
of the remote control.
To unlock, use the
top control.
If the top control accidentally becomes locked
and you do not have the remote control
nearby or there is something wrong with your
remote control, contact the dealer where you
purchased the projector or the service center.
43
Setting
Iris
This function is used to increase the contrast of
the image.
On .... Enable Iris function, increase the
contrast of the image.
Off .... Disable Iris function.
Iris
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Terminal
The VGA IN 2/VGA OUT terminal can be used
as computer input or monitor output. Press▲
to select input or output.
Computer 2 ...... Computer 2 input.
Monitor out ....... Monitor out.
OK
Select
Esc
Back
Terminal
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Off
Standby mode
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Adjust
Sound
This item is used to adjust the volume.
Sound ... Press  button to increase the
volume, press  button to
decrease the volume.
Mute ..... Press ▲ button to switch mute
function. (On/Off)
OK
Select
Esc
Back
Sound
Display
Color adjust
Sound
Volume
12
Mute
Off
Setting
Expand
Memory
Viewer
Info.
Adjust
44
OK
Select
Esc
Back
Setting
HDMI setup
When the external equipment is connected to "HDMI" terminal, if the image is not projected
properly, please switch the settings of "Image" or "Sound" in "HDMI setup" menu.
1 Press the MENU button to display the screen
menu. Press  button to select the
"Setting" menu icon. Press the OK to enter
the submenu entry.
2 Press  button to select "HDMI setup"
and then press the OK button.
3 Press  button to select "Image" or
"Sound" to adjust.
4 Press  button to switch the item.
Image
64-940 ....... Select when the HDMI terminal
of an external device (such as a
blu- ray player) is connected to the"
HDMI" terminal.
0-1023 ...... Select when the DVI-D terminal
output of an external device (such
as a computer) is connected to the
"HDMI" terminal via a conversion
cable or similar cable. Select also
when the HDMI terminal output of
a computer or other device is
connected to the "HDMI" terminal.
Note:
The optimal setting varies depending on
the output setting of the connected external
device. Refer to the operation instruction of
the external device regarding the output of the
external device.
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
On start
Color adjust
Normal
High land
Off
Lamp control
Cooling fast
Normal
Closed caption
Off
Key lock
Iris
Off
Terminal
Computer 2
Sound
HDMI setup
Move
Display
Off
Standby mode
...
OK
Select
Esc
Back
HDMI setup
Image
0-1023
Sound
Computer
Setting
Expand
Memory
Viewer
Info.
Adjust
OK
Select
Esc
Back
Sound
HDMI .......... Select when the HDMI cable is
connected, the image and audio
are transmitted, and you do not
need to connect the audio signal
separately.
Computer ... Select when the DVI-D terminal
output of an external device (such
as a computer) is connected to
the "HDMI" terminal via a
conversion cable or similar cable.
The sound will not be transmitted,
the audio signal is input to "AUDIO
IN" terminal.
45
Expand
The projector has Expand menu that allows you to set the other various expand functions
described as follows.
1 Press MENU button on the remote control to display screen menu. Press  button to select
"Expand", then press the OK button.
2 Press  button to select the item you want to set, press the OK button.
3 Press  button to adjust the item, then press the OK button.
Language
This projector provides multi-language screen
menu.
You can press button to select the language
you want.
Expand menu
Display
Color adjust
Setting
Expand
Memory
Viewer
Info.
Language
...
Auto setup
Keystone
Logo
Security
Power management
Filter counter
Test pattern
Network
Remote control
Factory default
Move
OK
Select
Esc
Back
Auto setup
Press AUTO button on the remote control to
execute "Input search", "Auto PC adj." and
"Auto keystone" functions.
Input search
Allows you to automatically detect input
signals. It stops when a signal is found. Press
 button to select an option below:
On ........ Enabled. This function is used to
detect input signals automatically
and stops when finding a signal.
Off ........ Disabled.
Auto PC adj.
On ........ Press the AUTO button on the
remote control or top control to
enable Auto PC adj. function
automatically.
Off ........ Cancel Auto PC adj. function.
Auto keystone
Auto ..... When detecting the projector is
tilted, correct the vertical keystone
in real time.
Manual ........ When pressing KEYSTONE
button on the remote control or
top control, perform a vertical
keystone.
Off ........ Disabled.
46
Auto setup
Display
Color adjust
Auto setup
Input search
Off
Auto PC adj.
On
Auto keystone
Off
Setting
Expand
Memory
Viewer
Info.
Adjust
Note:
OK
Select
Esc
Back
- "Input search", "Auto PC Adj." and "Auto Keystone"
cannot be set to "Off" at the same time. At least
one of them is set to "On".
- Sometimes the auto keystone maybe correct
image imperfectly, manual keystone is required.
- The Auto keystone function cannot work when
"Display" → "Project way" is set to "Ceiling/
Front" or "Ceiling/Rear".
Expand
Keystone
Keystone menu
This function is used to store or reset the
keystone correction when the AC power cord is
Keystone
unplugged.
Display
Keystone
Store
1 Press MENU button on the remote control
H/V Keystone
Color adjust
to display screen menu. Press  button
Corner correction
Setting
Curved correction
to select "Expand", then press the OK button.
Reset value
2 Press button to select "Keystone", press
Expand
the OK button.
Memory
Viewer
3 Press button to select the item you want
to set, press the OK button.
Info.
Keystone
Adjust
Select
Back
Sets whether or not to keep the keystone
correction after turn off the projector or plug out
the power cord.
Store ..... The keystone correction will be kept when plug out the power cord or turn off the
projector.
Reset .... When "Standby mode" is set to "Eco", plug out the power cord or turn off the projector,
the keystone correction will be canceled. When "Standby mode" is set to "Normal", plug
out the power cord, the keystone correction will be canceled; turn off the projector, the
keystone correction will be kept.
OK
Esc
H/V Keystone
Adjust when the horizontal or vertical trapezoid of the projected image is distorted.
Reduce the upper
width with  button.
Reduce the lower
width with  button.
Reduce the left
width with  button.
Reduce the right
width with  button.
Corner correction
Adjust when the four corners of the projected image are distorted.
Press▲▼◄►to adjust the item.
Corner correction
Upper left
Upper right
Lower left
Lower right
 Note:
● The white arrows indicate that there is no correction.
● A red arrow indicates the direction of correction.
● An arrow disappears at the maximum correction.
47
Expand
Curved correction
Adjust when the linearity is not uniform or the vertical and horizontal lines are distorted.
Press▲▼◄►to adjust the item.
Items
Operation
Adjustment
Adjust the right of
Press the►button
the width
Press the◄button
Adjust the left of
the width
Press the▼button
Adjust the bottom
of the width
Barrel
correction X/Y
Adjust the top of
Gain
Press the▲button
the width
Adjustment range
-40 ~ +40
-40 ~ +40
Adjust the right of
Press the►button
Barrel
the distortion
correction X
Adjust the left of
Offset
Press the◄button
0 ~ +1365
the distortion
Adjust the top of
Press the▲button
Barrel
the distortion
Correction Y
Adjust the bottom
Offset
Press the▼button
0 ~ +799
of the distortion
 Note:
● Either "H/V Keystone" , "Corner correction" or "Curved correction" setting value is valid. When
the "H/V Keystone" , "Corner correction" or "Curved correction" adjustment is finished, the
adjusted value will be reset when you adjust the other one.
● The "Curved Correction X Offset" and the "Curved Correction Y Offset" can not be adjusted
independently. After adjusting the "Curved Correction X/Y Gain" at the beginning, please adjust
the "Curved Correction X Offset" and "Curved Correction Y Offset".
● Press the KEYSTONE button on the remote control when the keystone screen is displaying (it
includes: H/V Keystone, Corner correction, Curved correction and Reset value), press 
button switch to the other adjustment screen.
● Correcting up to ±15° for the tilt in the vertical direction and ±15° for the tilt in the horizontal
direction are available for adjustments with "Keystone". However, the image quality will degrade
and it will get harder to focus with more correction. Install the projector so that the correction will
be as small as possible.
● Screen size will also change when "H/V Keystone" is used to perform various adjustments.
● Aspect ratio of the image size may shift depending on the correction.
Reset value
Return the corrected values to the factory default values.
Press▲▼to select "Reset value", then press the OK button, the state of the keystone correction is
released.
48
Expand
Logo
This function allows you to customize the screen logo with Logo select, Capture, Logo PIN code
lock and Logo PIN code change functions.
Logo Select
This function decides on the starting-up display
from following options.
Default .... Show the factory-set logo.
User..........Show the image captured by user.
Off ........... Show the countdown display only.
Logo
Display
Color adjust
Setting
Capture
You can capture a projected image as start logo .
Select "Capture" and press the OK button.
Confirmation dialog box appears, select "Yes"
to start capturing.
Logo
Logo select
Default
Capture
Logo PIN code lock
Off
Logo PIN code change
Expand
Memory
Viewer
Info.
Adjust
OK
Select
Esc
Back
Logo PIN code Lock
This function prevents an unauthorized person from changing the screen logo.
Off ............The screen logo can be changed freely from the Logo menu.
On ............The screen logo cannot be changed without a Logo PIN code.
If you want to change the Logo PIN code lock setting, press the OK button and the Logo PIN code dialog
box appears. Enter a Logo PIN code by following the steps below.
PIN code reset
Press  button to select a number, and then press the OK button to enter this number,
automatically move the cursor to next box. If you fixed an incorrect number, press MENU button to
reset it again.
Repeat this step to complete entering a three-digit number.
After entering the three-digit number, automatically move the cursor to "Set", and press the OK
button, then you can start to operate the projector.
If you entered an incorrect PIN code, the number (***) turn red, it will be reset automatically within
one second. Enter the correct PIN code all over again.
Logo PIN code change
You can change the Logo PIN code (three number). Press the OK button to select Logo PIN code
change. Logo Pin code dialog box appears, press ▲▼ button to enter the correct code. The New Logo
PIN code input dialog box appears. Set a new Logo PIN code, confirmation box appears, select Yes to
set the new Logo Pin code.
Be sure to note the new Logo PIN code and keep it on hand. If you lost the number, you could no longer
change the Logo PIN code setting.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE, WRITE DOWN THE NEW PIN CODE
IN COLUMN OF THE LOGO PIN CODE NO. MEMO ON PAGE 88, AND KEEP IT SECURELY.
SHOULD THE LOGO PIN CODE BE LOST OR FORGOTTEN, THE LOGO PIN CODE SETTING
CAN NO LONGER BE CHANGED.
49
Expand
Security
This function allows you to use the PIN code
lock and PIN code change functions to set the
security for the projector operation.
Security
Display
Color adjust
PIN code lock
This function prevents the projector from
being operated by unauthorized persons
and provides the following setting options for
security.
Off ............ Unlocked.
On ........... Enter the PIN code every time
turning on the projector.If you
want to change PIN code lock
setting or PIN code,you must
enter the PIN code. The orignal
PIN code is "111".
Security
PIN code lock
Off
PIN code change
Setting
Expand
Memory
Viewer
Info.
Move
OK
Select
Esc
Back
If you want to change the PIN code lock
setting, press the OK button, then PIN code
dialog box appears.
Enter PIN code
Press  button to select a number, and
then press the OK button to enter this number,
automatically move the cursor to next box. If
you fixed an incorrect number, press MENU
button to reset it again.
Repeat this step to complete entering a threedigit number.
After entering the three-digit number, move the
cursor to "Set", and press the OK button, then
you can start to operate the projector.
If you entered an incorrect PIN code,the
number (***) turn red, it will be reset
automatically within one second. Enter the
correct PIN code all over again.
PIN code change
The PIN code can be changed to three-digit
number. Press  button to select PIN code
change. Pin code dialog box appears, Press
 button to enter the correct code. The New
PIN code input dialog box appears. Set a new
PIN code.
50
CAUTION:
WHEN YOU HAVE CHANGED THE PIN
CODE, WRITE DOWN THE NEW PIN CODE
IN COLUMN OF THE PIN CODE NO. MEMO
ON PAGE 88, AND KEEP IT SECURELY.
SHOULD THE PIN CODE BE LOST OR
FORGOTTEN, THE PIN CODE SETTING CAN
NO LONGER BE CHANGED.
Expand
Power management
Power management
Display
Color adjust
Setting
Power management
Power management
No signal
Ready
Shut down
 Off
Timer
5
Min
Ready countdown
0
Min
Expand
Memory
Viewer
01 : 20
Time left before Lamp is off.
Info.
Move
OK
Select
Esc
Back
Note:
Factory default: "Timer: 5 min",
"Ready countdown: 0 min".
For reducing power consumption as well as maintaining the lamp life, the Power management
function turns off the projection lamp when the projector is not operated for a certain period. Select
one of the following options:
Ready .................. When the lamp has been fully cooled down, the POWER indicator changes to
green blinking. In this condition, the projection lamp will be turned on if the input
signal is reconnected or any button on the remote control or top control is
pressed.
Shut down ........... When the lamp has been fully cooled down, the power will be turned off.
Off ....................... Power management function is off.
Timer ................... If the input signal is interrupted and no button is pressed for more than 30
seconds, the timer display with No signal appears. It starts the countdown until
the lamp is turned off. Press  button to set the Timer(1~30min.)
Ready countdown..Set the time that ready status transfers to standby status automatically.(030min. 0 Min: not transfer automatically)
In ready status, press POWER button to switch to standby status, and press
any other button to turn on the projector.
51
Expand
Filter counter
Filter counter
This function is used to set a frequency for filter
cleaning.
When the projector reached a specified time
between cleanings, a Filter warning icon
appears on the screen, notifying the cleaning
is necessary. After cleaning the filter, be sure
to select RESET and set the timer. The Filter
warning icon will not turn off until the filter
counter is reset.
Filter counter ............ Display the using time
of the filter.
Timer ........................ Set the time to display
the warning icon.
Filter counter reset ... Reset the filter counter.
Display
Color adjust
Filter counter
Filter counter
9
Timer
H
200 H
Filter counter reset
Setting
Expand
Memory
Viewer
Info.
Move
OK
Select
Esc
Back
Filter counter reset?
Yes
No
Move
OK
Select
Esc
Back
Filter counter reset ?
Yes
OK ?
Yes
No
Move
OK
Select
Back
Esc
Test Pattern
This function is used to set the internal test
signal: Gray scale 1, Gray scale 2, Gray scale
3, Gray scale 4, Color bar, Red, Green, Blue,
Cross hatch, White, Black and Raster gray.
Display
Test Pattern
1/2
 Off
Color adjust
Gray scale 1
Setting
Gray scale 3
Display
Color adjust
Gray scale 2
Test Pattern
2/2
White
Black
Raster gray
Setting
Gray scale 4
Expand
Expand
Color bar
Memory
viewer
Red
Info.
Blue
Memory
viewer
Green
Info.
Cross hatch
Move
52
OK
Select
Esc
Back
Move
OK
Select
Esc
Back
Expand
Network
Function : PC controls projector via LAN.
Preparation:
1. Equipments: PC, projector, cables
2. Connection procedures:
Connect the projector to routers or switches of the LAN by direct or cross cable. If it fails to
connect PC and projector by parallel cable, please switch to cross cable as suggested.
3. After the computer is booted and the projector is plugged in, indicator lights of LAN interface
on will flash continuously.
Operation procedures:
1 Turn on the projector.
2 Obtain network address. DHCP set is displayed as On and obtain network address
automatically.( If familiar with network, you can set DHCP as Off and obtain network
address manually.)
Network
3 Enter network settings menu.
Display
Network setting
(1) Press MENU button on the remote control to
display screen menu. Press  button to
select Expand, then press the OK button.
Color adjust
(2) Press  button to select Network, and
then press the OK button to enter the network
menu.
MAC address ... Displays the MAC address
of wired network of this
projector.
IP address .........Displays the IP address of
wired network of this
projector.
Memory
Viewer
(3) When DHCP is set On, IP address, Subnet,
Gateway and DNS will be obtained
automatically, press the OK at "Set" to confirm
the parameters.
Setting
Network information
MAC address:
00:04:A3:97:69:DA
IP address:
192.168.1.100
Expand
Info.
----
LAN
Select
Back
Esc
Network setting
DHCP
On
IP address
Subnet
Gateway
DNS
Set
Cancel
Adjust
W hen DHCP is set Off, press the OK button to
enter IP address, then press  button to enter
Subnet, Gateway and DNS respectively,
press the OK at "Set" to confirm the parameters.
OK
ENTER
LAN
Select
Back
Esc
Network setting
DHCP
Off
IP address
192
192
168
168
1
1
Subnet
255
255
255
0
Gateway
192
168
1
1
DNS
192
168
1
1
100
100
Set
Cancel
Adjust
ENTER
Select
Esc
Back
 Note:
See page 59 for usage of Network.
53
Expand
Remote control
Remote control
This switching function prevents remote control
interfering when operating several projectors
or video equipment at the same time.
The projector is assigned 10 different remote
control codes (Code 0-9), which are default
initial code (Code 0) and another 9 codes (code
1-9).
Display
Color adjust
Remote control
Remote control
Code 0
RC sensor
Front
Setting
Expand
Memory
Viewer
Info.
Code set on the projector and remote control
should be the same. For example, when using
code 7 to operate the projector, the remote
control code also must be switched to Code 7.
Adjust
OK
Select
Esc
Back
Light
Change the projector's code: Select "Remote
control" in advanced menu.
Change the remote control code: Press the OK
button and a number key (0-9) on the remote
control for more than 5 seconds to switch the
codes. When the light start flashing, it means
code is completed.
Note:
● If the codes set on the projector and remote control
are different, it will not execute any operation. In
this case, switch the remote control code to the
same code as that of the projector.
● If the battery is removed for a long period of time
from the remote control, the remote control code
will be reset.
RC sensor
Set RC sensor when using remote control to
operate projector.
Front .....Choose the front remote control
receiver.
Back .... .Choose the back remote control
receiver.
Both ..... Choose both front and back remote
control receivers.
Display
Color adjust
Remote control
Remote control
Code 0
RC sensor
Front
Setting
Expand
Memory
Viewer
Info.
Adjust
OK
Select
Esc
Back
Factory default
This function returns all setting values except
for the User logo, PIN code lock, Logo PIN
code lock, Lamp counter and Filter counter to
the factory default settings.
54
Return to factory default?
Yes
No
Move
OK
Select
Esc
Back
Expand
Lamp counter
Be sure to reset the Lamp counter after the lamp is replaced. When the Lamp counter is reset, the
WARNING indicator stops lighting and the Lamp replacement icon disappears.
1 Press MENU button on the remote control to
display screen menu. Press  button
to select "Expand", then press the OK
button.
2 Press  button to select "Lamp
counter", press the OK button.
3 Press button to select "Lamp counter
reset" and then press the OK button.
"Lamp replacement counter reset? "
appears. Select "Yes" to continue.
Display
Color adjust
Lamp counter
Lamp counter
3
H
Lamp counter reset
Setting
Expand
Memory
Viewer
Info.
Move
OK
Select
Esc
Back
4 Another confirmation dialog box appears,
select "Yes" to reset the Lamp counter.
√ Note:
Do not reset the Lamp counter without
implementing lamp replacement. Be sure
to reset the Lamp counter only after
replacing the lamp.
Lamp replacement counter
Reset?
Yes
No
Move
OK
Select
Esc
Back
Lamp replacement counter
Reset ?
Yes
OK ?
Yes
No
Move
OK
Select
Esc
Back
55
Memory viewer
The Memory Viewer function makes it possible to project the pictures which are stored in the USB
memory when the USB memory is inserted into the projector
1 Press MEMORY VEIWER button on the remote control.
2 Press MENU button on the remote control to display screen menu. Press  button to select
"Memory Viewer", then press the OK button.
3 Press  button to select the item you want to set, press the OK button.
4 Press  button to adjust the item, then press the OK button.
Set Slide
Start the slide show.
Memory Viewer menu
Display
Color adjust
Setting
Slide transition effect
Set the slide transition effect when the slide
show image is switching.
Slide down ... Switch the image from the top to
the bottom.
Slide right .... .Switch the image from the left to
the right.
Sort Order
Set the sort order of the slide show.
Extend Order ...... Sort files or folders in
extended order.
Size Order .......... Sort files or folders in
amount of data order.
Time Order ......... Sort files or folders in stored
time order.
Name Order ....... Sort files or folders in name
order.
 Note:
See page 67 for Memory viewer function.
56
Expand
Set Slide
Slide transition effect
Slide right
Sort order
Extend order
Rotate
No rotate
Best fit
Off
Repeat
Off
Apply
Memory
Viewer
Info.
Move
OK
Select
Esc
Back
 Note:
● The "Memory Viewer" menu is available
when input the "Memory Viewer" signal.
● The menu except for "Set Slide" which setting
have been changed is not yet effective
before the "Apply" is not executed.
Memory viewer
Rotate
Set the rotate direction of image.
No Rotate ........... Rotate is disabled.
270 Degrees ...... Rotate 270 degrees in
anti-clockwise direction.
180 Degrees ...... Rotate 180 degrees.
90 Degrees ........ Rotate 90 degrees in anticlockwise direction.
Best Fit
Set the image whether or not to fit with the
projected screen.
On ...... Display the image to fit with the
aspect of the projected screen.
Off ...... Display in the normal pixels of the
image.
Repeat
Set whether or not to play the slide show
repeatly.
On ...... Repeat broadcast the first file after the
last file is broadcasted.
Off ...... Return to the thumbnail display after
the last file is broadcasted.
Apply
Execute the setting in slide show.
Press  to select "Apply", then press the
OK button, the setting of the items except for
"Set Slide" will be effective.
57
Information
The information menu is used to the detect signal of projected image and running state.
Menu operation
Press MENU button on the remote control or
top control to display the screen menu. Press
 to select Info., the information menu will
appear as the right picture.
The information below will display in
information menu.
Input
The selected input source is displayed.
H-sync freq .
The horizontal frequency of the input signal is
displayed in KHz or - - - -KHz when no signal is
detected.
V-sync freq .
The vertical frequency of the input signal is
displayed in Hz or - - - - Hz when no signal is
detected.
Lamp status
The setting status of "Lamp control" is
displayed.
Lamp counter
The usage time of the lamp is displayed.
Power management
The setting status of "Power management" is
displayed.
Image mode
The setting status of "Image mode" is
displayed.
58
info. menu
Display
Color adjust
Setting
Input
Computer 1
----
H-sync freq.
--- KHz
V-sync freq.
---
Hz
Lamp status
Lamp counter
9
Expand
Power management
Memory
Viewer
Image mode
H
Off
5 Min
Dynamic
Info.
Move
OK
----
Exit
Network Control Instructions
LAN control
Function : PC controls projector via LAN.
Preparation:
1. Equipments: PC, projector, cables
2. Connection procedures:
Connect the projector to routers or switches of the LAN by direct or cross cable. If it fails to
connect PC and projector by parallel cable, please switch to cross cable as suggested.
3. After the computer is booted and the projector is plugged in, indicator lights of LAN interface
and computer interface will flash continuously.
Operation procedures:
1 Turn on the projector.
2 Obtain network address. DHCP set is displayed as on and obtain network address
automatically. If familiar with network, you can set DHCP as close and obtain network
address manually.
3 Enter network settings menu.
Network
(1) Press MENU button on top control
Display
Network setting
or remote control to display screen
Network information
Color adjust
menu. Press ▲▼ button to select
MAC address:
00:04:A3:97:69:DA
"Expand" icon, then press the OK button.
IP address:
192.168.1.100
Setting
(2) Press ▲▼ button to select "Network"
setting and press the OK button enter
the network setting.
Expand
Memory
Viewer
Info.
(3) Press ▲▼ button to set DHCP as on.
----
OK
Select
Esc
Back
(4) Press ▲▼ button to "Set" and press
the OK button."Please wait..." appears.
LAN
Network setting
DHCP
On
IP address
Subnet
Gateway
DNS
Set
Cancel
Adjust
ENTER
Select
Esc
Back
 Note:
● When connecting to wireless network,please check the SSID/ ESSID and IP address in
"Network information" .
59
Network Control Instructions
4. Activate the Web browser in the personal computer.
5. Enter the IP address set by the projector into the URL input field of the Web browser.
6. Select "Login" to login the Network Display System page. (Both the initial name and passwords
are "admin".)
 Note:
● You can click the upper right corner of the web browser screen to select the display language.
● Do not perform setting or control simultaneously by starting up multiple web browsers. Do not
set or control the projector from multiple computers.
● Change the password first. (8 half-width characters). (page 61)
● If the screen for the web control is not displayed, consult your network administrator.
7. Items in Network Display System page including: "System Status", "General Setup", "Picture
Setup", "Image Setup" and "Network Setup".
①
②
③
④
⑤
LC-XBS500
① System Status
The "System Status" page is displayed by
clicking this item.
④ Image Setup
The "Image Setup" page is displayed by
clicking this item.
② General Setup
The "General Setup" page is displayed by
clicking this item.
⑤ Network Setup
The "Network Setup" page is displayed by
clicking this item.
③ Picture Setup
The "Picture Setup" page is displayed by
clicking this item.
60
Network Control Instructions
"System Status" page
Display the status of the projector for the following items.
LC-XBS500
①
②
③
① Model Name
Displays the model No. of the projector.
③ LAN Status
Displays the connection status of the LAN.
② Versions
Displays the version of the firmware of the
projector.
"General Setup" page
Change Password for Webpage is displayed.
①
②
③
④
⑤
⑥
① Enter Old password
Enters the configured password.
④ Apply
Updates th settings.
② Enter New password
Enters the new password.
⑤ Power
Switches on/off the power of the projector.
③ Confirm New password
Enters the wanted new password again for
confirmation.
⑥ Source Select
Switches the input source of the projector.
61
Network Control Instructions
"Picture Setup" page
①
②
③
④
⑤
⑥
① Brightness
Adjusts the brightness of the projected image.
② Contrast
Adjusts the contrast of the projected image.
③ Sharpness
Adjusts the sharpness of the projected image.
62
④ Color
Adjusts the color saturation of the projected
image.
⑤ Tint
Adjusts the skin tone of the projected image.
⑥ Color Temperature
Adjusts the color temperature of the projected
image.
Network Control Instructions
"Image Setup" page
①
②
③
④
⑤
⑥
⑦
⑧
⑨
⑩
⑪
① Aspect
Switches the aspect of the projected image.
⑦ Auto PC adj.
Executes the Auto PC adj. function.
② Fine sync
Adjusts the fine sync of the projected image.
⑧ V Keystone
Corrects the keystone in vertical direction.
③ H Positon
Adjusts the horizontal position of the projected
image.
⑨ H Keystone
Corrects the keystone in horizontal direction.
④ V Position
Adjusts the vertical position of the projected
image.
⑤ H.Size
Adjusts the total number of dots of the
projected.
⑩ Curved Correction
Corrects the pincushion or barrel of the
projected image.
⑪ Corner correction
Corrects the four corners of the projected
image.
⑥ Freeze
Swithces the freeze function between on
and off.
63
Network Control Instructions
"Network Setup" page
①
②
① LAN Setup
Select [Obtain an IP address automatically]
if you want to enable the DHCP client.
Gateway
Enter the default gateway address when
not using a DHCP server.
IP Address
Enter the IP address when not using a DHCP
server.
Subnet
Enter the subnet mask when not using a
DHCP server.
DNS
Enter the DNS server when not using a
DHCP server.
② Apply
Updates the settings.
8. PwPresenter software: when "Network" is selected in Source Select, you can project the current
computer images via network.
Input the IP address of the projector in webpage to enter the Network Display System, click
"Download" to download the pwPresenter software according to your operation system.
9. Click
icon to access the pwPresenter software.
①
⑥
②
64
③
④
⑤
Network Control Instructions
① Search for projector display
Click to enter Search, select the projector and connect it. Please setting the same IP address of
the projector in pwPresenter software, (such as: 192.168.1.100). Both the initial name and
passwords are "admin".
Note:
● Before use pwPresenter software to search, you need change Source Select to "Network".
② Play/Pause
Play or pause the selected image.
③ Choose capture mode
Choose a capture mode from "FullScreen", "FixedSize" or "Alterable."
④ Parameters Setting
Basic Setting: setting language,region of
capture image etc,.
Advanced Setting: setting image quality,
network port etc,.
65
Network Control Instructions
Global Setting: setting remote control, capture
by audio or screen ect,.
⑤ Network Display Management
Setting device and password management.
Multicast Setting: setting Sound volume,
Bandwidth and Capture rate ect,.
⑥ Disconnect the projector.
66
Using useful functions
Memory Viewer function
The Memory Viewer function is used to project the pictures which are stored in the USB memory when
the USB memory is inserted into USB A(VIEWER) terminal of the projector.
Memory Viewer function supports the following image files.
Extension
jpg/jpeg
Picture
bmp
png
Format
Baseline coding 24 bits
Progressive RGB 24 bits
Palettle-based1, 4, 8 bits,
RGB 24, 32 bits
True color 24 bits/48 bits
Description
The maximum resolution : 10 000 x 10 000
The maximum resolution : resolution of panel
The maximum resolution : resolution of panel
The maximum resolution : resolution of panel
tiff
The maximum resolution : 800 x 600
pdf
-
Display the Memory Viewer screen
1. Press the MEMORY VIEWER button on the remote control or INPUT button on the top control to
select the input source as Memory Viewer.
2. Insert the USB memory into the USB-A terminal of the projector directly, the standby screen
of "please press RC ENTER" appears when the USB memory icon is displayed on the screen.
3. Press the OK button on the remote control, the root directory of the USB memory will appear in
thumbnail on the screen.
Play the pictures
It will display a picture when play the picture manually every time.
1 Press ▲▼◄► to select a file.
2 Press the OK button, the picture will display on the full screen.
3 Press ►to switch to the next picture, press◄ to return to the previous picture.
4 Press the OK button on the remote control.
Executing the slide
All pictures in the same folder will play automatically when "Slide Transition Effect" of "Memory
Viewer" menu are set to the special setting.
1 Press ▲▼◄► to select a file.
2 Press the "MENU" button to select the "Memory Viewer" → "Set Slide".
3 Press the OK button.
● The picture will display on the full screen.
● Press the OK button to return to the thumbnail screen.
67
Using useful functions
Play the video
Playing the video file.
press ▲▼◄► to select a video file and press the OK button to display the video on the full
screen.
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
Exit the video playing, and return to the thumbnail screen.
Paused or go on playing video.
00:00:52/00:03:30
Forwards or backwards the video(skip 10sec).
Forwards or backwards the video at double speed.(skip 60 sec)
The video can be played repeatly.
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
00:00:52/00:03:30
Show play time and total time.
00:00:52/00:03:30
Play the PDF
Playing the PDF file.
press ▲▼◄► to select a PDF file and press the OK button, playing the PDF on the full screen.
55
5 5
5
55
5
GO
5
5
GO
1
GO
5GO 1 5
55GO 1
1
GO
1 5
55
GO
5
GO
1
GOGO
11
1
1/6
1/6
1
5
GO
55
GO
1
5
GO
1
1/6
1/6
GO
GO
GO
GOnext page.
or
55
55 5 5Displays
11 the previous
11
5
5
5
1/6
1/6
1/6
The
increases
or decreases by 5 pages.
1/6
1
1 5 pageGOnumber
GOpage number increases or decreases by 1 page.
GO
The
1/6
11
Jumps to page number directly.
1/6
Switches PDF file between full screen display or whole page display.
1/6
Switches
the display size on 3 levels of magnification. Press ▲▼on the
remote control to move the display screen up and down.
1
1/6
Remove the display screen up, down, left and right by ▲▼◄►button on
the remote control.
1
Exit the PDF file, and return to the thumbnail screen.
Termination of the Memory Viewer
1. Press ▲▼◄► to the thumbnail
which is displayed on the upper left corner.
2. Press the OK button on the remote control to return to the standby screen of "please press RC
ENTER".
3. Remove the USB memory directly.
68
Using useful functions
USB Display function
The USB Display function is used to project the image from the computer which is connected to USBB(DISPLAY) terminal of the projector by a USB converting cable.
■ When using Windows
Windows operation environment
OS
CPU
Amount of memory
Windows Vista 32 bit, Windows 7 32/64 bit, Windows 8 32/64 bit
Intel Core 2 Duo 2.0 GHz or faster, the compatible processor
256 MB or more (Recommended : 512 MB or more)
Hard-disk free space 20 MB or more
Display
Resolution 640 x 480 or more, 1 600 x 1 200 or less
● There is no guarantee for all computers that meet the above conditions will operate properly.
Projecting the USB Display
1. Connect the USB-B terminal of the projector to a computer with a USB converting cable.
2. Press the USB DISPLAY button on the remote control or switch the input source to USB
Display.
● Press the INPUT button on the top control and select the input source in the Input menu.
● The startup screen will be displayed automatically due to the driver which is built-in the projector, and
excutes the installation according to the instructions of the screen. The displaying of the auto installation
screen depends on the setting of computer. At this time, please select "Run autorun.exe". Please
double-click "autorun.exe" in the folder of the USB Display when the automatical startup is disabled.
● The image on the computer screen is projected.
3. Click the driver icon
in the task bar of computer and select one item in Pop-up menu.
● Pop-up menu is only displayed in English.
● The item which is displayed in gray is unavailable.
Active audio/
Disable audio
Play video/
Pause video
Start/Stop
Exit
Set whether to output the audio from the computer.
Switch between play and pause the image.
Set whether to display the image from the computer.
Exit USB Display.
Note:
- The driver is not installed in your computer, and it will be removed from the computer when
disconnecting the USB cable.
- It will take a while when you want to project the computer screen.
- Connect a USB cable directly to the USB connector of a computer. It will not work when
connecting through a USB hub.
Termination of the USB display
When terminate the USB display, remove the USB cable directly. There is no need to follow
"Remove hardware safely" when a USB cable is disconnected.
69
Using useful functions
■ When using Mac OS
Mac OS operating environment
OS
CPU
Amount of memory
Mac OS X 10.5, 10.6, 10.7
Power PC G4 1GHz or faster
512 MB or more
Hard-disk free space 20 MB or more
Display
Resolution 640 x 480 or more, 1 600 x 1 200 or less
● There is no guarantee for all computers that meet the above conditions will operate properly.
Projecting the USB Display
1. Connect the USB-B terminal of the projector to a computer with a USB converting cable.
2. Press the USB DISPLAY button on the remote control or switch the input source to USB
Display.
● Press the INPUT button on the top control and select the input source in the Input menu.
● The image on the computer screen is projected.
3. Double-click "Monitor.app" in the virtual disk that has been mounted.
4. Right-click the driver icon
in the dock of computer and select one item in Pop-up menu.
● Pop-up menu is only displayed in English.
● The item which is displayed in gray is unavailable.
Active audio/
Disable audio
Play video/
Pause video
Start/Stop
Quit
Set whether to output the audio from the computer.
Switch between playing and pausing the image.
Set whether to display the image from the computer.
Terminate the USB Display.
Note:
- It will take a while when you want to project the computer screen.
- Connect a USB cable directly to the USB connector of a computer. It will not work when
connecting through a USB hub.
Termination of the USB display
When terminate the USB display, remove the USB cable directly.
70
Maintenance and cleaning
WARNING indicator
The WARNING indicator shows the state of the function which protects the projector. Check the
state of the WARNING indicator to take proper maintenance.
The projector is shut down and the WARNING
indicator is flashing red.
When the temperature inside the projector
exceeds the normal temperature, the projector
is automatically shut down to protect internal
components. The WARNING indicator is
blinking while the projector is being cooled
down. When the projector has cooled down
enough (to its normal operating temperature),
it can be turned on again by pressing the
POWER button.
 Note:
The WARNING indicator continues to
blink even after the temperature inside
the projector returns to normal. When the
projector is turned on again, the
WARNING indicator stops blinking.
Check the items below:
– Did you provide appropriate space for the
projector to be ventilated?
Check the installing condition to see if
ventilation slots are not blocked.
– Has the projector been installed near the
duct or vent of an airconditioning?
Move the installation of the projector away
from the duct or vent.
– Are the air filters clean? Clean the air filters
periodically.
The projector is shut down and the WARNING
indicator lights red.
When the projector detects an abnormal
condition, it is automatically shut down to
protect the internal components and the
WARNING indicator lights red. In this case,
unplug the AC power cord and plug it, and
then turn on the projector once again to verify
operation. If the projector cannot be turned on
and the WARNING indicator lights red, unplug
the AC power cord and contact the service
station for servicing and maintenance.
WARNING indicator
WARNING indicator
flashes red.
WARNING indicator
WARNING indicator
lights red.
Caution
Do not leave the projector with the AC power cord connected under an abnormal condition.
It may result in fire or electric shock.
71
Maintenance and cleaning
Cleaning the filter
The air filter prevents dust from accumulating on the surface of the optical elements inside
the projector. Should the air filter become clogged with dust particles, it will reduce cooling
fans’ effectiveness and may result in a buildup of internal heat and adversely affects the life of
the projector. If the Filter warning icon appears on the screen, the air filter should be cleaned
immediately. Clean the air filter following the steps below.
1 Turn off the projector, and unplug the AC
power cord from the AC outlet.
2 Remove the air filter.
3 Gently clean the filter with a brush.
4 Reinstall the filter into the projector properly.
Filter
Caution
Do not operate the projector with
the air filter removed. Dust may
accumulate on the optical elements,
degrading picture quality.
Do not put any small objects into the
air intake vents. Otherwise, it may
result in malfunction of the projector.
Filter counter reset
Be sure to reset the filter counter after cleaning
or replacing the filter.
1. Press Menu on the remote control to display
the screen menu. Press to select
"Expand", then press the OK button.
2. Press  to select "Filter counter", and then
press the OK button.
Press  to select "Filter counter reset" and
press the OK button, "Filter counter
Reset?" appears on screen, select "Yes" to
continue.
3. When another dialog box pops up, select
"Yes" to reset the filter.
72
Recommendation
We recommend avoiding dusty/smoky
environments when you operate the projector.
Usage in these environments may cause poor
image quality.
When you use the projector under dusty or
smoky conditions, dust may accumulate on the
lens, LCD panels, or optical elements inside the
projector. When the symptoms above are
noticed, contact your authorized dealer or
service station for proper cleaning.
Maintenance and cleaning
Clean the projector lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning
cloth that contains non-abrasive camera
lens cleaner, or use a lens cleaning paper or
commercially available air blower to clean the
lens.
Avoid using an excessive amount of cleaner.
Abrasive cleaners, solvents, or other harsh
chemicals might scratch the surface of lens.
Clean the cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector surface with a soft
dry cleaning cloth. When the cabinet is heavily
soiled, use a small amount of mild detergent
and finish with a soft dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals
might scratch the surface of the cabinet.
When the projector is not in use, put the
projector in a pouch to protect it from dust and
scratches.
73
Maintenance and cleaning
Replace the lamp
When the projection lamp of the projector
reaches its end of life, the Lamp replacement
icon appears on the screen and LAMP
indicator flashes yellow. Replace the lamp with
a new one of the same type promptly. The
timing when the LAMP indicator should light is
depending on the lamp mode.
Indicator
When the projection
lamps reaches its end
of life, LAMP indicator
flashes yellow.
Lamp replacement icon
Lamp replacement
CAUTION
As temperature inside the projector is high,
you should cool the projector for at least 45
minutes before you open the lamp cover.
CAUTION
For the sake of safety, only use the lamp of
the same model. Never drop the lamp onto the
ground nor touch the glass bulb! The glass can
shatter and hurt.
CAUTION
When the lamp isn’t illuminated, it may indicate that the lamp has been damaged.
When you replace the lamp in a projector installed on the ceiling, you should stand beside
the lamp cover other than under it; for the broken glass may fall down to hurt you. To do that,
remove the lamp cover gently to avoid being hurt by falling debris. If debris drops into your
eyes or mouth, you should see the doctor immediately.
To replace the lamp, follow the steps below:
Screw
1. Power off the projector and unplug the power
cord. Then let the projector cool for at least
45 minutes.
2. Loosen the screw on the lamp cover to
remove the cover.
3. Make sure the lamp is well protected and
remove three screws. Hold the handle to
take out the lamp.
4. Install a new lamp with the same model and
tighten the three screws. Make sure the
installation is correct. Put lamp cover in place
and then tighten the screw.
5. Plug the AC power cord and power on the
projector.
74
Handle
Lamp cover
Screw
Maintenance and cleaning
ORDER REPLACEMENT LAMP
Replacement lamp can be ordered through your dealer. When ordering a projection lamp, give the
following information to the dealer.
Replacement Lamp Model No.: 23040049
LAMP HANDLING PRECAUTIONS
This projector uses a high-pressure lamp which must be handled carefully and properly.
Improper handling may result in accidents, injury, or create a fire hazard.
● Lamp life may differ from lamp to lamp and according to the environment of use. There is no
guarantee of the same life for each lamp. Some lamps may fail or terminate their life in a shorter
period of time than other similar lamps.
● If the projector indicates that the lamp should be replaced, i.e., if the WARNING indicator lights up,
replace the lamp with a new one IMMEDIATELY after the projector has cooled down. (Follow
carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the
lamp with the WARNING indicator lighted may increase the risk of lamp explosion.
● A Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its
lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in
which the projector and lamp are being used.
IF A LAMP EXPLODES, THE FOLLOWING SAFETY PRECAUTIONS SHOULD
BE TAKEN .
If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an
authorized service station for a checkup of the unit and replacement of the lamp. Additionally, check
carefully to ensure that there are no broken shards or pieces of glass around the projector or coming
out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully.
No one should check the inside of the projector except those who are authorized trained technicians
and who are familiar with projector service. Inappropriate attempts to service the unit by anyone,
especially those who are not appropriately trained to do so, may result in an accident or injury caused
by pieces of broken glass.
75
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
- Make sure you have properly connected the projector to peripheral equipment.
- Make sure all equipment is connected to the AC outlet and the power is turned on.
- If the projector does not project an image when it is connected to a PC, restart the PC.
Problems
No power
No initial displaying
– Solutions
- Plug the power cord of the projector into the AC power outlet.
- Check whether the POWER indicator lights red.
- Only when the POWER indicator lights red you can power on the
projector again.
- Check the WARNING indicator. If it is blinking red, the projector can not be
powered on. (Page 71)
- Check the projection lamp. (Page 74)
- Unlock the “Key lock” function. (Page 43)
- Make sure that Logo function is not set to "Off". (Page 23, Page 49)
Initial displaying is inconsistent
with factory defaults
Input signals are automatically
switched (can’t be switched)
- Make sure that Logo function is not set to "Off" or "User". (Page 49)
Ambiguous images
- Adjust the focus.
- Set a more proper projection distance.
- Check whether the lens needs to be cleaned.
- When moved from a environment with low temperature to
the one with higher temperature, water will be condensed
on the lens. If so, you have to wait till the condensed water
disappears.
- Check the function of “Ceiling/rear”. (Page 35)
- Check the function of “Ceiling”.
Image turns over leftward/
rightward
Image turns over upward/
downward
Image not bright enough
No image
76
- Properly adjust the Input search function.
- Check whether the contrast or brightness is adjusted correctly.
(Page 39-40)
- Check whether the Image mode is properly selected. (Page 38)
- Check the function of lamp brightness adjusting. (Page 42)
- Check the LAMP indicator. If the indicator lights yellow, it means
the service life of the lamp is over. You should replace the lamp with
a new one of the same model immediately.
- Check the connection between Computer or video equipment and
the projector.
- Check whether the signal from Computer is correct. If connected to
certain laptops, the settings of their video adapters need to be
changed. You can refer to the operating instructions of the Computer
for such modification.
- Images can show up only about 20 seconds after the projector
is powered on.
- Check the input signal, color system, video system or Computer
system mode.
- Make sure that the temperature doesn’t exceed the permitted
operating temperature(41˚F-104˚F [5˚C - 40˚C] ).
- If BLANK function is enabled, no image will appear on the screen.
You can then press the BLANK button or other button on the
remote control.
Appendix
No Sound
- Check the audio cable connection from audio input source.
- Adjust the audio source.
- Press the VOLUME + button.
- Press the Mute button.
- When the AUDIO OUT is plugged in, the projector’s built-in
speaker is not available.
- Is the image projected? The sound can only be heard when the
image is projected.
The color is abnormal
- Check the input signal, color system, video system or computer
system mode.
- Make sure that Blackboard is not selected in Image Mode menu.
Auto PC adj. function does not - Check the Input signal. Auto PC adj. function can not work when
work.
480p, 576p, 720p, 480i, 576i, 1080i or 1080p is selected.
The Settings cannot be saved - Make sure you have selected “store” after you changed the
after turing off the projector.
settings. Some settings can’t be saved if “ store” is not selected.
Power management function does - Power management function can not work while Freeze or Blank
not work.
function is running.
Logo function does not work.
- Check connections and input source.
Auto setup function does not work. - Make sure no function in the Auto setup menu is set to “Off”.
- Make sure “On” is not chosen in the Ceiling function.
The image is distorted or
- Check and adjust “ Screen” menu.
disappears.
PIN code dialog box appears at - PIN code lock is being set.
start-up
The remote control does not work. - Check the batteries.
- Make sure no obstruction is between the projector and the
remote control.
- Make sure you are not too far from the projector when using the
remote control. Maximum operating range is 5 m.
- Make sure the code of the remote control is conformed to that of
the projector.
- Unlock the Key lock function in the Setting menu for the remote
control.
Indicators light or flash.
- Refer to Indicators and projector condition to check the status of
the projector.
Exclamatory mark appears on the - Your operation is invalid. Operate correctly.
screen.
top control cannot be operated.
- Unlock the Key lock in Setting -> Key lock.
Unable to unlock the Logo PIN
code, Key lock or PIN code lock.
- Contact the dealer or the service center.
Warning:
High voltages are used to operate this projector. Do not attempt to open the cabinet.
If problems still persist after following all operating instructions, contact the dealer where you
purchased the projector or the service center. Specify the model number and explain about the
problem. We will advise you how to obtain service.
77
Appendix
Menu Tree
Main menu
Sub menu
Setting
Auto PC adj.
Fine sync
H Position
V Position
0 to 31
-5 to +5
-5 to +5
H.Size
-15 to +15
Aspect
Project way
Menu positon
Display
Background display
System
Color adjust
78
Image mode
Note
In different signal,
H.Size range will
different?
Normal
Wide
Front
Rear
Ceiling/Front
Ceiling/Rear
Upper left
Upper right
Center
Lower left
Lower right
Black
Blue
Auto
1080p
1080i
1035i
720p
575p
575i
480p
480i
Component input
Auto
PAL
SECAM
NTSC
NTSC4.43
PAL-M
PAL-N
PAL60
S-video Input
Video Input
Dynamic
Standard
Cinema
Blackboard(Green)
Colorboard
User Image
Appendix
Main menu
Color adjust
Setting
Sub menu
Setting
Contrast
Brightness
Color temp.
Red
Green
Blue
Sharpness
Contrast
Brightness
Color
Tint
Red
Green
Blue
Sharpness
On start
Standby mode
High land
Lamp control
Cooling fast
Closed caption
Key lock
Iris
Terminal
0-63
0-63
High/Mid/Low
0-63
0-63
0-63
0-15
0-63
0-63
0-63
0-63
0-63
0-63
0-63
0-15
On/Off
Normal/Eco
On/Off
Normal/Eco
Normal/60 sec/0 sec
Off, CC1,CC2,CC3, CC4
Off, Projector, Remote control
On/Off
Computer2/Monitor out
Sound
0-25
Mute
On/Off
Sound
Image
HDMI setup
Sound
Language
Auto setup
Expand
Keystone
Note
Computer input
Component Input
S-video Input
Video Input
64-940
0-1023
HDMI
Computer
Multi-language provide
Input search
On/Off
Auto PC adj.
On/Off
Off
Auto keystone Auto
Manual
Keystone
Store/Reset
H/V Keystone
Corner correction
Curved correction
Reset value
79
Appendix
Main menu
Sub menu
Setting
Logo select
Logo
Note
Default/User/Off
Capture
Logo PIN code lock On/Off
Logo PIN code change
Security
Expand
PIN code lock
On/Off
PIN code change
Power management
Ready
Shut down
Off
Timer
Ready countdown
Filter counter
Filter counter
Timer
Filter counter reset
Test Pattern
Off,Gray scale1(1-4), Colorbar, Red,
Green, Blue, Cross hatch, White,
Black, Raster gray
Network setting
LAN(On/Off)
DHCP
IP address
Subnet
Gateway
DNS
Network
information
MAC address
IP address
Remote control
Code 0 (0-9)
RC sensor
Front/Back/Both
Network
Remote control
Factory default
Lamp counter
Lamp counter
Lamp counter reset
Set Slide
Slide transition effect
Memory Viewer
Sort Order
80
Slide down
Slide right
Extend order
Size order
Timer order
Name order
Appendix
Main menu
Sub menu
Setting
Rotate
No Rotate
270 Degrees
180 Degrees
90 Degrees
Memory Viewer
Info.
Input
Best Fit
Repeat
Apply
Input
H-sync freq.
V-sync freq.
Lamp status
Lamp counter
Power management
Image mode
Computer 1
Computer 2*
HDMI
Component
Video
Note
On/Off
On/Off
* Computer 2 can't be
selected when using
the VGA IN 2/VGA
OUT terminal as
VGA OUT.
S-video
Network
Memory Viewer
USB Display
81
Appendix
Indicator and projector state
Check the indicator to know about the state of projector.
Indicator
POWER
Green/Red
LAMP
Yellow
State of projector
WARNING
Red
In power-off state (AC power cord not connected).
In standby state. Press POWER to power on the projector.
In normal working state.
Ready to be in standby mode or the projection lamp is being cooled.
Before you power on the projector, you have to wait till the lamp is
cool enough and the power indicator stops flashing.
In power management ready mode.
Internal temperature too high, can’t be powered on. When the
projector is cool enough, the temperature is restored to the normal
value and the power indicator is illuminated red, you can then power
on the projector.
Can’t be powered on because error is detected. You must unplug
the power cord. Then insert it again and power on the projector. If
the projector is powered off again, you must cut off the power and
contact the local distributor or repair center. In this case, stop the
projector. Otherwise, electric shock or fire may occur.
The service life of the lamp is over. You should replace it with a new
one in time.
Green
Red
Flash green
Flash red
Yellow
Off
* When the lamp reaches the end of its life, the LAMP indicator lights Yellow. In this case,
replace the lamp with a new one promptly.
82
Appendix
Compatible computer specifications
This projector can receive the signals below:
Scanning frequency
Signal format
Resolution
horizontal
frequency
(Khz)
Field
Frequency
(Hz)
Dot Frequency
(Mhz)
NTSC/NTSC4.43/PAL-M/
PAL-60
720x480i
15.7
59.9
-
PAL/PAL-N/SECAM
720x576i
15.6
50.0
-
525i(480i)
720x480i
15.7
59.9
13.5
720(1440)x480i*3
15.7
59.9
27.0
720x576i
15.6
50.0
13.5
720(1440)x576i*3
15.6
50.0
27.0
525p(480p)
720x483
31.5
59.9
625p(576p)
720x576
31.3
750(720)/60p
1280x720
750(720)/50p
Signal
RGB
Component
HDMI
o
o
o
o
o
o
o
27.0
o
o
o
50.0
27.0
o
o
o
45.0
60.0
74.3
o
o
o
1280x720
37.5
50.0
74.3
o
o
o
1125(1080)/60i*4
1920x1080i
33.8
60.0
74.3
o
o
o
1125(1080)/50i
1920x1080i
28.1
50.0
74.3
o
o
o
1125(1080)/24p
1920x1080
27.0
24.0
74.3
o
o
o
1125(1080)/24sF
1920x1080i
27.0
48.0
74.3
o
o
o
1125(1080)/25p
1920x1080
28.1
25.0
74.3
o
o
o
1125(1080)/30p
1920x1080
33.8
30.0
74.3
o
o
o
1125(1080)/60p
1920x1080
67.5
60.0
148.5
o
o
o
1125(1080)/50p
1920x1080
56.3
50.0
148.5
o
o
o
31.5
59.9
25.2
o
o
35.0
66.7
30.2
o
o
37.9
72.8
31.5
o
o
37.5
75.0
31.5
o
o
43.3
85.0
36.0
o
o
35.2
56.3
36.0
o
o
37.9
60.3
40.0
o
o
48.1
72.2
50.0
o
o
46.9
75.0
49.5
o
o
53.7
85.1
56.3
o
o
49.7
74.6
57.3
o
o
48.4
60.0
65.0
o
o
56.5
70.1
75.0
o
o
60.0
75.0
78.8
o
o
68.7
85.0
94.5
o
o
625i(576i)
VGA
SVGA
MAC16
XGA
640x480
800x600
832x624
1024x768
o
MXGA
1152x864
67.5
74.9
108.0
o
o
MAC 21
1152x870
68.7
75.1
100.0
o
o
1280x720
1280x720
37.1
50.0
60.5
o
o
44.8
60.0
74.5
o
o
47.8
59.9
79.5
o
o
60.3
74.9
102.3
o
o
68.6
84.8
117.5
o
o
41.3
50.0
68.0
o
o
49.7
60.0
83.5
o
o
62.8
74.9
106.5
o
o
71.6
84.9
122.5
o
o
60.0
60.0
108.0
o
o
64.0
60.0
108.0
o
o
78.2
72.0
135.1
o
o
80.0
75.0
135.0
o
o
91.1
85.0
157.5
o
o
39.6
49.9
69.0
o
o
47.7
59.8
84.8
o
o
65.3
60.0
121.8
o
o
82.3
74.9
156.0
o
o
1280x768
1280x800
MSXGA
SXGA
1366x768
SXGA+
1280x768
1280x800
1280x960
1280x1024
1366x768
1400x1050
Video/S-Video
83
Appendix
Scanning frequency
Signal
Signal format
Resolution
horizontal
frequency
(Khz)
Field
Frequency
(Hz)
Dot Frequency
(Mhz)
RGB
WXGA+
1440x900*5
55.9
59.9
106.5
o
o
1600x900
1600x900
55.9
60.0
119.0
o
o
UXGA
1600x1200
75.0
60.0
162.0
o
o
WSXGA+
1680x1050
1920x1080
WUXGA
Component
HDMI
65.3
60.0
146.3
o
o
1920x1080
*5
66.6
59.9
138.5
o
o
1920x1200
*5
74.0
60.0
154.0
o
o
Video/S-Video
*3 Pixel-Repetition signal (dot clock frequency 27.0 MHz) only.
*4 When a 1125 (1035)/60i signal was input, it is displayed as a 1125 (1080)/60i signal.
*5 VESA CVT-RB (Reduced Blanking)-compliant.
 Note:
● “i” added to the resolution value indicates an interlaced signal.
● When interlaced signals are connected, flicker may occur on the projected image.
● The specification is subject to change without any prior notice.
84
Appendix
Technical Specifications
Mechanical properties
Dimensions (W×H×D )
Net Weight
Adjustable foot
386.4mmx126.1mmx326.7mm(including the adjustable foot and projector
lens)
4.6Kg (with Lens)
40mm
LCD resolution
LCD system
LCD resolution
Compatible signals
Color standard
HDTV signal
Scanning frequency
Optical elements
Image size (diagonal lines)
Projection distance
Lens
Lamp Consumption(W)
Terminal
VGA IN 1/YCbCr/S-VIDEO IN
VGA IN 2/VGA OUT
HDMI terminal
LAN terminal
USB-B
USB-A
RS-232 terminal
Wired remote input terminal
AUDIO OUT
0.63" TFT, active matrix, 3-panel (LC-XBS500)
0.59" TFT active matrix, 3-panel (LC-WBS500)
XGA 1024X768 (LC-XBS500) / WXGA 1280X800(LC-WBS500)
PAL, SECAM, NTSC, NTSC4.43, PAL-M, PAL-N and PAL60
480i, 480p, 575i, 575p, 720p, 1035i, 1080i and 1080p
Horizontal frequency: 15 kHz –100 KHz; Vertical frequency: 48 – 85 Hz
30"-300", adjustable
4:3 0.882m-9.180m(W) 1.482m-15.171m(T) (LC-XBS500)
16:10 0.938m-9.735m(W) 1.573m-16.086m(T) (LC-WBS500)
F=1.6-2.08, f=19.36-31.94mm; Manual zooming and focusing; Zoom times:
1.65X
280W NSH
Mini D-sub 15 pin x1
Mini D-sub 15 pin x1
HDMI A type 19 pin (the number of HDMI terminals varies from model to model. See the
real product.)
100 Base-TX (100Mbps)/10 Base-T (10Mbps) RJ45
x1(display)
(read+Wifi Dongle)/Wifi Dongle Optional/Microsoft Office/Adobe Reader
D-sub 9 pin x1
Mini Jack x1(Input)
3.5mm Mini Type Stereo x1
AUDIO IN
MONO(R/L)
VIDEO IN terminal
Power
Voltage and power consumption
Fuse
Internal audio AMP
Internal speaker
Operating Environment
Operating temperature
3.5mm Mini Type Stereo x1
3.5mm Mini Type Stereo x2
3.5mm Mini Type Stereo x1
Storage Temperature
High land
Remote control
Battery
Operating Range
Dimensions
Net Weight
Accessories
14˚F-140˚F (-10˚C - 60˚C)
1400 m
AC 100–240 V, 50/60 Hz
250V/10A
7W x 1, single chanel
10W RMS 8ohm, x1
41˚F-104˚F (5˚C - 40˚C)
AA or LR6 1.5V ALKALINE TYPE x 2
16.4' (5 m)/±30
48mm (W) x 26mm (H) x 160mm (D)
67g (including batteries)
Power Cord, Owner's Manual(CD), Remote Control & battery, VGA Cable
Lens Protection Ring
● The aforesaid specification is subject to change without prior notice.
● Liquid crystal panel is made on the basis of high standard, where 99.99% of the pixels are effective.
Due to the nature of the liquid crystal panel, a fraction of the pixels (0.01% or less) may be ineffective.
85
Appendix
Configurations of terminals
COMPUTER IN 1 terminal pin assignments and signal names
12
11
6
13
7
14
8
1
9
2
1
2
3
4
5
6
7
8
15
10
3
4
5
R/PR/S-C
G/Y/S-Y
B/PB/----GND
GND
GND
GND
9
10
11
12
13
14
15
+5V
GND
GND
DDC data
HD/SYNC
VD
DDC clock
COMPUTER IN 2/COMPUTER OUT terminal pin assignments and signal names
12
11
6
7
1
13
8
2
14
9
3
1
2
3
4
5
6
7
8
15
10
4
5
R
G
B
----GND
GND
GND
GND
RS232 terminal (D-SUB-9 pin)
6
1
7
8
2
3
9
4
5
9
10
11
12
13
14
15
NC
GND
----DDC data
HD/SYNC
VD
DDC clock
LAN terminal
1
2
3
4
----RXD
TXD
-----
5
GND
6
7
8
9
-----------------
87654321
1
2
3
4
TX +
TX ---------
HDMI terminal pin assignments and signal names
2
1
6
4
3
5
8
7
10 12 14
9
1
2
3
4
5
6
7
8
9
10
16 18
11 13 15 17 19
USB-B terminal
86
1
2
4
3
1
2
3
4
V Bus
Data Data +
GND
T.M.D.S data2+
T.M.D.S data2 shield
T.M.D.S data2–
T.M.D.S data1+
T.M.D.S data1 shield
T.M.D.S data1–
T.M.D.S data0+
T.M.D.S data0 shield
T.M.D.S data0–
T.M.D.S clock+
11
12
13
14
15
16
17
18
19
T.M.D.S clock shield
T.M.D.S clock–
CEC
----SCL
SDA
DDC/CEC GND
+5V
Hot plug detection
5
6
7
8
--------RX +
RX -
Appendix
Content of hazardous substances and elements
Name of parts
Hazardous substances and elements
Hg
Cd
Cr6+
PBB
Pb
PBDE

Optical parts*1
○
○
○
○
○

○
○
○
○
○
Electric parts*2

○
○
○
○
○
Cabinet, mechanical parts


○
○
○
○
Lamp unit
○
○
○
○
○
○
Batteries
Others(Remote control,

○
○
○
○
○
cable and other parts)
○: It means that contents of hazardous substances in all homogeneous materials in this part don’t
exceed "Required Limitations" specified in SJ/T11363-2006.
×: It means that contents of hazardous substances in at least one homogeneous material in this part
exceed "Required Limitations" specified in SJ/T11363-2006.
Note:
*1 :Optical parts includes optical lens, monitor, reflection lens ect.
*2 :Electric parts includes PCB, internal wires, fans, power supply, sensors etc.
Dimensions
Unit: mm

Screw Holes for Ceiling Mount
Screw: M4
Depth: 10.0
126.1
M4×10
87
Appendix
PIN code memorandum
Write down the PIN code in the blank below and keep it, If you forgot or lost the number and unable to
operate the projector, contact the service center.
Factory default PIN code 111*
PIN code lock
Factory default PIN code 111*
Logo PIN code Lock No.
*If this 3-digit number is changed,
the factory default number will be ineffective.
88
Appendix
RS232 Control Method
1. Connection
1.1 Port Setting
Item
Method
Value
Asynchronous communication
Bits per seconds
Data bits
Parity
Stop bits
Flow control
19200
8
none
1
none
1.2 Wiring
Connect the computer and projector with RS232 cross cable.
Projector Control Port
PC COM
CD
1
1
N.C.
RXD
2
2
RXD
TXD
3
3
TXD
DTR
4
4
N.C.
SG
5
5
SG
DSR
RTS
6
6
N.C.
7
7
RTS
CTS
8
8
CTS
RING
9
9
N.C.
(D-Sub 9 Pin)
(D-Sub 9 Pin)
2. Commands
Case sensitive, each command end by[CR](Carriage)
Command
Item
C00
POWER ON
POWER OFF(Power off
C01
immediately)
C02
POWER OFF
C36
HDMI
C05
VGA IN 1
C06
VGA IN 2
Command
C07
Video
S-Video
C34
C33
C15
C16
C17
Item
Component
Network
Memory viewer
USB Display
89
Appendix
2.1 POWER ON
Command "C00" [CR] (Hex:0x43 0x30 0x30 0x0d)
Details
Return
Power ON when projector standby
OK
[ACK] [CR]
NG
"?" [CR]
2.2 POWER OFF (Power OFF immediately)
Command "C01" [CR] (Hex:0x43 0x30 0x31 0x0d)
Details
Return
Power OFF immediately
OK
[ACK] [CR]
NG
"?" [CR]
2.3 POWER OFF
Command "C02" [CR] (Hex:0x43 0x30 0x32 0x0d)
Details
Return
"Power off?" displays while send the command, just like press the "POWER"key.
OK
[ACK] [CR]
NG
"?" [CR]
2.4 HDMI
Command "C36" [CR] (Hex:0x43 0x33 0x36 0x0d)
Details
Return
Change the input to "HDMI".
OK
[ACK] [CR]
NG
"?" [CR]
2.5 VGA IN 1
Command "C05" [CR] (Hex:0x43 0x30 0x35 0x0d)
Details
Return
Change the input to "Computer 1".
OK
[ACK] [CR]
NG
"?" [CR]
2.6 VGA IN 2
Command "C06" [CR] (Hex:0x43 0x30 0x36 0x0d)
Details
Return
90
Change the input to "Computer 2".
OK
[ACK] [CR]
NG
"?" [CR]
Appendix
2.7 Video
Command "C07" [CR] (Hex:0x43 0x30 0x37 0x0d)
Details
Return
Change the input to "Video".
OK
[ACK] [CR]
NG
"?" [CR]
NG
"?" [CR]
2.8 S-video
Command "C34" [CR] (Hex:0x43 0x33 0x34 0x0d)
Details
Return
Change the input to "S-Video".
OK
[ACK] [CR]
NG
"?" [CR]
2.9 Component
Command "C33" [CR] (Hex:0x43 0x33 0x33 0x0d)
Details
Return
Change the input to "Component".
OK
[ACK] [CR]
NG
"?" [CR]
2.10 Network
Command "C15" [CR] (Hex:0x43 0x31 0x35 0x0d)
Details
Return
Change the input to "Network".
OK
[ACK] [CR]
NG
"?" [CR]
2.11 Memory viewer
Command "C16" [CR] (Hex:0x43 0x31 0x36 0x0d)
Details
Return
Change the input to "Memory viewer".
OK
[ACK] [CR]
NG
"?" [CR]
2.12 USB Display
Command "C17" [CR] (Hex:0x43 0x31 0x37 0x0d)
Details
Return
Change the input to "USB Display".
OK
[ACK] [CR]
NG
"?" [CR]
91
U.S.A.
Canada
Deutschland & Österreich
Eastern Europe
China
South East Asia
Australia
Japan & Worldwide
EIKI International, Inc.
30251 Esperanza
Rancho Santa Margarita
CA 92688-2132
U.S.A.
Tel: 800-242-3454 (949)-457-0200
Fax: 800-457-3454 (949)-457-7878
E-Mail: usa@eiki.com
EIKI Deutschland GmbH
Am Frauwald 12
65510 Idstein
Deutschland
Tel: +49-6126-9371-0
Fax: +49-6126-9371-14
E-Mail: info@eiki.de
EIKI (Shanghai) Co., Ltd.
LAKESIDE OASIS MIDDLE RING
BUSINESS CENTRE
Block 1, Room 606,
1628, Jin Sha Jiang Road
Shanghai, 200333
CHINA
Tel:
86-21-3251-3993
Service Hot line: 86-21-3251-3995
Fax:
86-21-3251-3997
E-mail: info@eiki-china.com
EIKI AUSTRALIA PTY LTD
Level 5, 11 Queens Road, Melbourne,
Victoria 3004
Tel: +61 (03) 8530 7048
Fax: +61(03) 9820 5834
E-Mail: sales@eiki.net.au
EIKI CANADA - Eiki International, Inc.
P.O. Box 156, 310 First St. - Unit 2,
Midland, ON, L4R 4K8, Canada
Tel: 800-563-3454 (705)-527-4084
Fax: 800-567-4069 (705)-527-4087
E-Mail: canada@eiki.com
EIKI CZECH SPOL. s.r.o.
Nad Cementárnou 1163/4a
Praha 4, Podolí
147 00
Czech Republic
Tel: +420 241 410 928
+420 241 403 095
Fax: +420 241 409 435
E-Mail: info@eiki.cz
EIKI Industrial (M) Sdn Bhd
No. 11, Nouvelle Industrial Park,
Lorong Teknologi B, Taman Sains Selangor
1, Kota Damansara PJU5,
47810 Petaling Jaya, Selangor Darul Ehsan,
Malaysia
Tel: +603-6157-9330
Fax: +603-6157-1320
E-Mail: sales@eiki.my
EIKI Industrial Company Limited.
6-23 Teramoto, Itami-shi, Hyogo,
664-0026 JAPAN
Tel: +81-72-782-9492
Fax: +81-72-781-5435
WorldWide Website http://www.eiki.com
P/N:4100697500
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising