RY803111 QUICK REFERENCE GUIDE

WARNING:

This Quick Reference Guide is not a substitute for reading the operator’s manual. To reduce the risk of injury or death, user must read and understand operator’s manual before using this product. All page references refer to the operator’s manual.

FIRST TIME ASSEMBLY STARTING THE UNIT (COLD START) USING DETERGENT

1 Install the handle and connect battery cable (see page 8).

5 Connect your garden hose to the pressure washer

(see page 9).

1 Add fuel (see page 11).

NOTICE:

Do not use E15 or E85 fuel in this product. It is a violation of federal law and will damage the unit and void your warranty.

Only use unleaded gasoline containing up to 10% ethanol.

5 Slide the lock button down and push the engine switch to the START position. Engine can also be started by pulling the recoil starting grip until the engine runs (see page 12).

1

2

1

Pour pressure washer detergent in soap tank (see page 14).

DETERGENT

2 Install blue soap nozzle page 13).

(see 3

Squeeze trigger and wait

approx. 5 seconds for detergent (see page 14).

5 S

2 Connect the spray wand to the trigger handle

(see page 8).

Completely uncoil garden hose or remove

completely from reel to prevent kinks.

Turn water faucet on fully.

3 Connect the high pressure hose to the trigger handle

(see page 8).

6

Make sure there are no leaks.

With no nozzle installed, squeeze the trigger to relieve air pressure. Hold the trigger until a steady stream of water appears.

Add entire bottle of lubricant provided to the pressure washer (see page 10).

4

Connect the high pressure hose to the pump

(see page 9).

7

Turn the fuel valve to CLOSED before adding lubricant.

Set unit on flat surface so engine is level.

Remove dipstick, wipe clean, put back in hole

(but don’t screw in) and check lubricant level.

Install battery pack (see page 12).

NOTE: Fully charge the battery pack before use.

Completely uncoil and straighten high pressure hose to prevent kinks.

DO NOT OVERTILT THE UNIT!

This is a 4-cycle engine. Do not mix fuel and lubricant together.

Mix fuel stabilizer with gasoline according to manufacturer’s directions prior to filling the tank.

2 Turn the fuel valve to OPEN (see page 12).

FUEL VALVE (OPEN)

3 Push choke in to the START position (see page 12).

CHOKE (START)

4 Push in at the top of the switch to turn engine ON

(see page 12).

SLIDE LOCK BUTTON DOWN

AND PUSH ENGINE SWITCH TO START

OR PULL STARTER GRIP

AND ROPE TO START

Use of soap nozzle will activate soap injector at a 20:1 dilution ratio.

WARNING! Never use bleach or solvent-based detergent.

• Will damage your pump

• Will void your warranty

• Will damage plants/shrubs If soap injection hose comes loose from pressure washer, reattach it here.

NOZZLE SELECTION GUIDE

Use the chart below to determine the correct nozzle for your job.

6

If the engine does not start after each pull of the starter grip and rope or after the engine switch is moved to the START position, squeeze the trigger to relieve water pressure before attempting to start the engine again.

Allow engine to run for several seconds, then pull choke out until it clicks into RUN position

(see page 12).

5 S

CHOKE (RUN)

RESTARTING THE UNIT

(HOT RESTART)

1

Pull starter grip and rope to start or push the engine switch to the START position (see page 12).

HIGH PRESSURE

(NO SOAP WHEN USING THESE NOZZLES)

LOW

PRESSURE

(FOR SOAP OR

GENTLE RINSE)

ABRASIVE

Concrete, Brick, Masonry

Siding, Gutters, House

Fencing, Deck, Patio

Lawn Equipment, Boat, RV

0º Red 25º Green 40º White

Blue Soap

Nozzle

GENTLE

   

  

  

  

 Recommended Nozzle  Use With Caution for Certain Applications

BEFORE STORING THE UNIT

1

1

1 Always add Pump Protector to the unit after each use and before storing. This will significantly improve pump life. (See page 14)

Pump Protector is available from your local retailer. For further assistance, call customer service at

1-800-860-4050.

To add, follow the instructions provided by the Pump Protector manufacturer.

PUMP

PROTECTOR

2 2

If the engine does not start:

• check for enough fuel;

• may need to adjust choke position;

• try starting again.

Make the most of your purchase! Go to www.ryobitools.com and register your new tool online. For questions about operating or maintaining your product, please call, 1-800-860-4050.

991000755

2-7-17 (REV:01)