Omega | CL1000 Series | Owner Manual | Omega CL1000 Series Owner Manual

Omega CL1000 Series Owner Manual
WARRANTY/DISCLAIMER
OMEGA Engineering, Inc. warrants this unit to be free of defects
in materials and workmanship for a period of 13 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1)
month grace period to the normal one (1) year product warranty
to cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for
evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written
request. Upon examination by OMEGA, if the unit is found to be
defective, it will be repaired or replaced at no charge. Omega’s
WARRANTY does not apply to defects resulting from any action of
the purchaser, including but not limited to mishandling, improper
interfacing, operation outside of design limits, improper repair, or
unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of
having been damaged as a result of excessive corrosion; or current,
heat, moisture or vibration; improper specification; misapplication;
misuse or other operating conditions outside of OMEGA’s control.
Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for
any omissions or errors nor assumes liability for any damages
that result from the use if its products in accordance with
information provided by OMEGA, either verbal or written.
OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with
respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC),
used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or
with any nuclear installation or activity, medical application, used on
humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and,
additionally, purchaser will indemnify OMEGA and hold OMEGA
harmless from any liability or damage whatsoever arising out of the use
of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA
Customer Service Department.
BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
FOR WARRANTY RETURNS,
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number under
which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
3.Repair instructions and/or specific problems relative to
the product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST of the repair or
calibration,
2. Model and serial number of the
product, and
3.Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers
the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable
form, in whole or in part, without the prior written consent of OMEGA
ENGINEERING, INC.
MQS3529/0417
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
5
6
with the
(up arrow) button or
(Down arrow)
button. Holding the
button and the
(Up)/
(Down) button for an extended period will cause
the setpoint temperature to advance more rapidly to a
desired value. The minimum and maximum setpoints
are locked out at 0 and 260°C (32 and 500°F),
respectively.
Changing the Display Units from °C to °F or
(°F to °C)
Press and hold the
(Up) and
(Down) buttons on
the controller at the same time for 3-4 seconds, then
release. The display will be flashing between “tune –
off”. Press the
button one time. The display will be
flashing between “LEVEL-1”. While holding the
(Modify) key down press the
button one time. The
display will be flashing between “LEVEL-2”. Now that
you are on menu level 2 release the
button. Press
the
button eleven times. The display will now be
flashing between “unit-°F” or “unit-°C”. To change the
current units setting press and hold the
button,
then press the
button one time to change
or
between units. To save your change and return to the
run mode press and hold the
buttons at the
and
same time for 3-4 seconds, then release.
Communication (RS-232)
This section only applies to CL1000 Series Calibrators
purchased with optional RS-232 Communications
(-C2) Option
Your calibrator unit has been factory pre-wired
and configured for ease of use with a stereo jack
connection on the side panel that will require no
additional wiring. An interface cable, Part No.
OM-NOMAD-CP9 is included with your unit for easy
connection between your benchtop calibrator and PC.
BENCHTOP CONTROLLER
INTERNAL WIRING
STEREO PLUG –– DB–9
INTERFACE CABLE
TX
RX
GRN
CONTROLLER
2
3
4
5
6
7
TX
RX
GND
1
9 10 11 13 13 14 15 16
1
STEREO JACK SIDE PANEL
PC COM PORT
DB–9
Wiring Connections From Calibrator To PC
For complete product manual:
www.omega.com/manuals/manualpdf/M3529.pdf
NOTE:
The CN9-SW software is Windows 95/98/NT/2K/
XP compatible.
Cool-Down Procedure
1. Turn the power switch on the back of the calibrator
to “standby” mode.
2. The cooling fan may continue to run or turn on
after several minutes if the heater assembly inside
the unit has not yet fully cooled down to ambient
temperature. Do not remove the power cord or
the main line power until the fan stops running
permanently.
3. It is now safe to remove your unit from the power
source and/or return to storage.
Overheat Reset Switch
If the unit is operated at high temperatures in elevated
ambient temperatures, an overheat condition may
occur. In an overheat situation a mechanical reset
switch on the right side panel will pop and open the
heater circuit. The controller will still have power.
While the controller will be demanding heat from the
heater, the process temperature will fall continuously
until it equalizes with room temperature. If an
overheat condition occurs, let the unit cool off for one
hour (leave the unit on), then press the reset button,
firmly. If this does not correct the problem, contact the
factory.
OVERHEAT RESET SWITCH
FRONT
FAN
BACK
HANDLE (IN RETRACT POSITION)
5
1.8 m (6 ft.)
8
Calibrators with the –C2 option come complete with
communication software, OMEGA part number CN9SW. The software is designed to interface with your
calibrator.
Overheat Reset Switch (Right Side Panel)
CL1000 SERIES
Mini hot point® Dry
Block Probe Calibrator
®
omega.com info@omega.com
Servicing North America:
U.S.A.:Toll-Free: 1-800-826-6342 (USA & Canada Only)
Customer Service: 1-800-622-2378 (USA & Canada Only)
Engineering Service: 1-800-872-9436 (USA & Canada Only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
Canada:Toll-Free: 1-800-826-6342 (USA & Canada Only)
Tel: (514) 856-6928
e-mail: generalinfo@omega.ca
Fax: (514) 856-6886
Web: www.omega.com
Servicing Mexico and Latin America:
Mexico/Tel: 001-800-099-0420 (Mexico Only)
Latin America
Tel: 001-203-359-7577
(Outside Mexico) Fax: 001 (203) 968-7290
e-mail: ventas@mx.omega.com
Web: mx.omega.com
Servicing Asia:
China:Hotline: (+86) 800 819 0559, (+86) 400 619 0559
e-mail: info@cn.omega.com
Web: cn.omega.com
Servicing Europe:
France:
Freephone: 0805 541 038 (France only)
Tel: 01 57 32 48 17
Fax: 01 57 32 48 18
e-mail: esales@omega.fr
Web: www.omega.fr
Germany/
Austria:
Freephone: 0800 826 6342 (Germany only)
Tel:+ 49 (0)7056 9398-0
Fax: +49 (0) 7056 9398-29
e-mail: info@omega.de
Web: www.omega.de
Italy
Freephone: 800 906 907 (Italy only)
Tel: +39 022 333 1521
Fax: +39 022 333 1522
e-mail: commerciale@it.omega.com
Web: it.omega.com
Netherlands:
Benelux
Freephone: 0800 099 33 44 (Netherlands only)
Tel: +31 070 770 3815
FAX: +31 070 770 3816
e-mail: esales@omega.nl
Web: www.omega.nl
Spain:
Freephone: 800 900 532 (Spain only)
Tel: +34 911 776 121
Fax: +34 911 776 122
e-mail: ventas@es.omega.com
Web: es.omega.com
United
Kingdom:
Freephone: 0800 488 488 (United Kingdom only)
Tel: +44 (0)161 777 6611
Fax: +44 (0)161 777 6622
e-mail: sales@omega.co.uk
Web: www.omega.co.uk
It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety
and EMC/EMI regulations that apply. OMEGA is constantly pursuing certification of
its products to the European New Approach Directives. OMEGA will add the CE
mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used
for, human applications.
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
ARTWORK/PRODUCT ART/
DWGS/START HERE ARROW
Start Here
2
3
4
If you have a “~230VAC” model you must first
connect the international style power cord to the
proper connector used in your country or local area
(connector not provided).
-------------------------------------------------------------------Certification CE (CL1000 ~230 VAC)
--------------------------------------------------------------------
Ambient Temperature Effects
When operating the unit at an ambient temperature
greater than 24°C, do not exceed the “Maximum
Allowable Probe Well Temperature” shown below.
Failure to adhere to these guidelines may cause a
safety switch inside the unit to open the heater circuit.
If this occurs refer to the section titled Overheat Reset
Switch or section 3.2.6 in the User’s Guide.
• Hole in center of probe well is a vent hole, not
a probe hole.
• To ensure the highest degree of accuracy
possible, when placing probes into the well,
make sure the probe tip goes all the way down
to the bottom of the probe well (the full 4.5").
• After inserting or removing probes into the
probe well allow the calibrator time to stabilize
before making your measurement. Adding or
removing probes changes the total mass of the
probe well, the controller will require time to
adjust for this change and stabilize back to the
temperature you have set.
PROBE WELL
PROBE WELL FINGER GUARD
CL1000
500.0
Amb. Temp. Max. Setpoint
°C (°F)
°C (°F)
24.0 (75)
260 (500)
24.4 (76)
252 (486)
25.6 (78)
244 (472)
26.7 (80)
237 (458)
27.8 (82)
229 (444)
28.9 (84)
221 (430)
30.0 (86)
213 (416)
31.1 (88)
205 (402)
32.2 (90)
198 (388)
33.3 (92)
190 (374)
CE
FA
ON
TI
®
HOT SU
R
HOT POINT®
Dryblock Calibrator
CA
U
Mounting
Mount the unit in an ambient environment
between the specified 32 to 122°F (0 to 50°C) on
a bench, table top or shelf in a horizontal position and operate at least ten inches from any air
obstructions to the fan, front panel or rear panel.
Do not block the bottom or top vented covers of the
unit.
Calibrator power requirements:
• 3.15 amps @ 115 VAC~ (±10%) 50/60 Hz, 275W
• 1.6 amps @ 230 VAC~ (±10%) 50/60 Hz, 275W
NOTE:
CA
UT
HOT SU
R
General Description
The CL1000 is a portable, rugged, benchtop, dry
block calibration source with a built-in precision
PID digital controller. The calibrator is used to test
and calibrate temperature probes. The probe well
can be set to any temperature between +11 to 260°C
(+20 to 500°F) when being operated in ambient temperatures up to 24°C (75°F).
Probe Well Styles
N
IO
Precautions:
• Follow all safety precautions and operating
instructions outlined in this manual.
• Never leave your calibrator unattended when in
use.
• Keep out of reach of all children.
• Never touch the probe well or probes when hot
without proper protection.
• Never place any objects other than temperature
probes in the well.
• Do not operate in flammable or explosive environments.
• Never operate with a power cord other than the
one provided with your unit.
• Turn unit off and disconnect main power cord
before attempting any maintenance or fuse
replacement.
• Never disconnect main power cord or main power
source when unit is still hot.
• Do not connect and or operate this unit to a nongrounded, non-polarized outlet or power source.
• This unit is intended for indoor use only. Avoid
exposure to moisture or high humidity.
• Never operate the unit outside.
•Do not return your unit to storage when hot, allow
unit to cool down to ambient temperature.
Power Connection
Connect the unit to a stable, earth grounded AC
mains supply of the correct voltage for the model
calibrator you have. Use the power cord provided.
CE
FA
Using This Quick Start Manual
Use this Quick Start Manual with your CL1000
series Mini hot point® Dry Block Probe Calibrator
for easy installation and basic operation. For
detailed information, refer to the User’s Guide
(Manual Number M3529).
1/32 DIN CONTROLLER
NOTE: HOLE IN CENTER OF
PROBE WELL IS A VENT HOLE,
NOT A PROBE HOLE.
Controller Front Panel Buttons
Modify Key: Press and hold to view current
setpoint temperature. While held, press the
decrease or increase key to change the
setpoint.
Maximum Setpoint Temperature Vs. Ambient Temp.
NOTE:
Decrease Key: Press in conjunction with
Modify Key in order to decrease setpoint.
An increase of ambient temperature of +0.6°C (+1°F)
above 24°C (75°F) reduces maximum setpoint by
4°C (7°F).
Increase Key: Press in conjunction with
Modify Key in order to increase setpoint.
Dimensions: mm (inch)
Changing the Controller Parameters
In the default mode the digital display indicates the
probe well temperature known as (PV) Process
Variable. Holding down the modify button causes
the display to show the programmed setpoint known
as (SV) Setpoint Variable. Making changes to the
setpoint or units of measurement settings are made
(Modify) button in conjunction
by pressing the
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising