Omega | CSi8DH Series | Owner Manual | Omega CSi8DH Series Owner Manual

Omega CSi8DH Series Owner Manual
TM
User’s Guide
Shop online at
omega.com
e-mail: info@omega.com
For latest product manuals:
www.omegamanual.info
CS8DPT SERIES
Benchtop Controllers
omega.com info@omega.com
U.S.A.
Headquarters:
Servicing North America:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves
the right to alter specifications without notice.
CS8DPT Series Benchtop Controllers
Table of Contents
Section
Page
Section 1 Introduction ....................................................................................... 1
1.1 Precautions .................................................................................................... 1
1.2 Safety Warnings and IEC Symbols...............................................................1
Section 2 Installation ......................................................................................... 2
2.1 Unpacking and Inspection .......................................................................... 2
2.2 Main Power Connection .............................................................................. 3
2.3 Power Cords .................................................................................................. 3
Section 3 Operation .......................................................................................... 4
3.1 Front Panel .................................................................................................... 4
3.2 Rear Panel ...................................................................................................... 4
3.3 Sensor Input Wiring ..................................................................................... 5
3.5 Controller Setup and Programmming ....................................................... 6
Section 4 Communication ............................................................................... 7
4.1 Communication Option ............................................................................... 7
4.2 Ethernet .......................................................................................................... 7
4.3 RS-232/485 ..................................................................................................... 7
Section 5 Maintenance ..................................................................................... 8
5.1 Calibration ..................................................................................................... 8
5.2 Cleaning ......................................................................................................... 8
5.3 Fuse Replacement ......................................................................................... 8
Section 6 Specifications ................................................................................... 9
i
CS8DPT Series Benchtop Controllers
NOTES:
ii
Introduction
1
Section 1 Introduction
1.1
Your CS8DPT series Benchtop Controller is ideal for laboratory use and
applications requiring portable temperature measurement and control. The
CS8DPT features a universal input that can be reconfigured by you for use
with a thermocouple, RTD or Voltage/Current signal. These controllers are
factory configured and calibrated. It is important that you read this manual
and additional manuals outlined in Section 6 completely and follow all safety
precautions in both manuals before operating your unit.
Precautions
• Follow all safety precautions and operating instructions outlined in this manual.
• Keep unit out of reach of all children.
• Do not operate in flammable or explosive environments.
• Never operate with a power cord that is not properly rated for use with your unit.
• Remove and or disconnect main power cord before attempting any
maintenance or fuse replacement.
• Do not connect and or operate this unit to a non-grounded, non-polarized
outlet or power source.
NOTE:
There are no user serviceable parts inside your unit. Attempting
to repair or service your unit may void your warranty.
CAUTION:
This product is not designed for use in human medical or
nucleur applications.
1.2
Safety Warnings and IEC Symbols
This device is marked with international safety and hazard symbols in
accordance with EN61010-1. It is important to read and follow all precautions
and instructions in this manual before operating or commissioning this device as
it contains important information relating to safety and EMC. Failure to follow
all safety precautions may result in injury and or damage to your calibrator.
Use of this device in a manor not specified by the manufacturer may impair
protection devices and safety features provided by the unit.
Caution, risk of electric shock
Caution, refer to accompanying documents
Figure 1.IEC symbols
CAUTION:
All electrical connections and wiring should be performed by
suitably trained personnel only.
1
2
Installation
Section 2 Installation
2.1
Unpacking
Remove the packing list and verify that you have received all your equipment.
If you have any questions about the shipment, please call our Customer Service
Department at
1-800-622-2378 or 203-359-1660.
We can also be reached on the Internet at omega.com
e-mail: info@omega.com
When you receive the shipment, inspect the container and equipment for any
signs of damage. Note any evidence of rough handling in transit. Immediately
report any damage to the shipping agent.
NOTE:
The carrier will not honor any damage claims unless all shipping material is saved for inspection. After examining and
removing contents, save packing material and carton in the
event reshipment is necessary.
The following items are supplied with your unit:
• CS8DPT Series Benchtop Controller (1 each)
• Main Power Cord (See Section 2.2.2 Power Cords)
• Output Power Cord (2 each)
• This Users Guide and Controller Manual #M3355 (1 each), Quick Start Manual
#MQS3355 (1 each)
• Communications Manual #M-3629 (1 each) with Ethernet models only.
• Communications Manual #M-3397 (1 each) with RS-232/485 models only.
• Warranty Extension Card (1 each)
2
Installation
2.2
2.2.1
2
Main Power Connection
Operation
Your Benchtop Controller will operate from 90 to 240VAC, 50/60 Hz, 2400W.
NOTE:
All power line connections to your unit are fused. When
operating on single-phase power source such as 120VAC in
the U.S.A, the main neutral line is also fused.
2.3 Power Cords
A main power cord has been included with your unit.The following optional
power cords are also available for use with your Benchtop Controller.
Omega Part No.
POWER CORD-UK
(United Kingdom, Ireland, 250V)
POWER CORD-IT
(Italy, 250V)
POWER CORD-DM
(Denmark, 250V)
POWER CORD-E-10A
(Continental Europe, 250V)
POWER CORD-NA
(USA, Canada, Mexico, 120V)
POWER CORD-SE
(Striped Leads, 250V)
CAUTION:
All electrical connections and wiring should be performed by
suitably trained personnel only.
3
3
Operation
Section 3 Operation
3.1 Front Panel Controls, Indicators
Figure 3.1 Front Panel Controls, Indicators
3.2 Rear Panel Controls and Connections
Figure 3-2 Rear Panel Controls and Connections
4
Operation
3
3.3 Universal Input, Sensor Wiring
PROCESS CURRENT INPUT (EXTERNAL EXCITATION)
THERMOCOUPLE CONNECTION
1
–
2 3 4
5 6
1
2 3 4
5 6
+ +
–
7 8
7 8
+
–
PROCESS CURRENT INPUT (INTERNAL EXCITATION)
1
2
3 4
5 6
7 8
500/1000 OHM RTD CONNECTION
1
2 3 4 5 6
JUMPER
7 8
RTD (500/1000) 4-WIRE
RTD (500/1000) 3-WIRE - ADD JUMPER
RTD (500/1000) 2-WIRE - ADD JUMPER
–
+
PROCESS VOLTAGE INPUT (WITH INTERNAL EXCITATION)
1
2
3 4
5 6
7 8
100 mV
1V or 10V
100 OHM RTD CONNECTION
1
2 3 4
5 6
7 8
PROCESS VOLTAGE INPUT (WITHOUT EXTERNAL EXCITATION)
1
2
3 4
5 6
7 8
RTD (100) 4-WIRE
RTD (100) 3-WIRE - ADD JUMPER
RTD (100) 2-WIRE - ADD JUMPER
100 mV
1V or 10V
Figure 3.3 Universal Input, Sensor Wiring
5
3
Installation
3.5 Controller Setup and Programming
3.5.1 Factory Configuration
All units are factory configured and calibrated for Type-K thermocouple unless
a different setup was requested when you ordered your unit. Your unit can be
reconfigured in the field to a different input type without the need to recalibrate
the controller. The procedure for changing the controllers programming can be
found in the accompanying manual M3355.
6
Communications Option
4
Section 4 Communication Option
4.1 Communication (Ethernet, RS-232/485)
Your controller has been factory pre-wired and configured for ease of use with
your communication option. Connections are made on the rear panel.
4.2 Ethernet
The RJ45 connection on the back of the controller has been extended out to the
rear panel on your Benchtop meter. Connection and use of the ethernet option is
outlined in manual #M3629 that was included with your unit.
4.3 RS-232/485
Your controller has been factory pre-wired and configured for ease of use with a
standard DB9 female connector on the rear panel. Page 6 of your communication
manual #M3397 shows how your rear panel connector has been wired.
Connections to your PC should be straight through wiring as shown below.
BENCHTOP METER
REAR PANEL
1
6
2
7
3
8
4
YOUR PC
9
5
1
6
2
7
3
8
4
9
5
Figure 4.3 Wiring Diagram
7
5
Maintenance
Section 5 Maintenance
5.1
Calibration
This unit has been fine-tuned and factory calibrated to give optimum
performance over its full operating range. Refer to manual M3355 for additional
information on meter calibration and setup.
CAUTION:
Remove all electrical connections and power before attempting any maintenance or cleaning.
5.2 Cleaning
Lightly dampen a soft clean cloth with a mild cleaning solution and gently clean
the benchtop meter.
5.3
Fuse Specifications and Replacement
WARNNG:
Disconnect all power from source before attempting fuse
replacement.
CAUTION:
For continued protection against the risk of fire, replace fuses
with only the same size, type, rating and safety approvals
indicated here and on the rear panel of your unit.
NOTE:
All power line connections to your unit are fused. When operating on single-phase power source such as 120VAC in the
USA, the neutral line is also fused.
5.3.1
All Models - 90 to 230VAC 50/60 Hz, 4W
Main Power Fusing:
2ea, T0.1A, 250 VAC, (Time-Lag)
(Rear Panel) F1,F2
UL./CSA/VDE Approved (5mm dia. x 20mm
long).
8
Specifications
6
Section 6 Specifications
6.1 Benchtop Configuration
NOTE:
All other specifications are located in your accompanying
manual(s)
Model CS8DPT:
with Ethernet:
with RS232/485:
Manual #M3355, MQS3355
Manual #M3629
Manual #M3397
Sensor Input(s)/Channels:
Model CS8DPT
Single Channel, Universal Input
Power:
All Models:
Fused:
90 to 240 Vac, 50/60 Hz, 2400W
Time-Lag, 0.1A, 250V
Output:
All Models:
Fused:
90 to 240 Vac, 50/60 Hz, 1200W
Fast-Blow, 5A, 250V
Enclosure:
Material:
Size:
Weight:
Case - Painted Aluminum, Handle – Anodized
Aluminum
20.95 W x 9.525 Hx 20.32 cm D
(8.25 W x 3.75 H x 8” D)
1.36 kg (3 lbs.)
9
Notes
NOTES:
10
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a
period of 61 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month
grace period to the normal five (5) year product warranty to cover handling and shipping time. This
ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service
Department will issue an Authorized Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;
or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for
any damages that result from the use of its products in accordance with information provided
by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN
(AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and
on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent
breakage in transit.
FOR NON-WARRANTY REPAIRS, consult
FOR WARRANTY RETURNS, please have the
OMEGA for current repair charges. Have
following information available BEFORE contacting
the following information available BEFORE
OMEGA:
contacting OMEGA:
1.Purchase Order number under which the product
1. Purchase Order number to cover the COST
was PURCHASED,
of the repair,
2.Model and serial number of the product under
2. Model and serial number of the product, and
warranty, and
3. Repair instructions and/or specific problems
3. Repair instructions and/or specific problems
relative to the product.
relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2015 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the
prior written consent of OMEGA ENGINEERING, INC.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
TEMPERATURE
M
U Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
M
U Wire: Thermocouple, RTD & Thermistor
M
U Calibrators & Ice Point References
M
U Recorders, Controllers & Process Monitors
M
U Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
M
U Transducers & Strain Gages
M
U Load Cells & Pressure Gages
M
U Displacement Transducers
M
U Instrumentation & Accessories
FLOW/LEVEL
M
U Rotameters, Gas Mass Flowmeters & Flow Computers
M
U Air Velocity Indicators
M
U Turbine/Paddlewheel Systems
M
U Totalizers & Batch Controllers
pH/CONDUCTIVITY
M
U pH Electrodes, Testers & Accessories
M
U Benchtop/Laboratory Meters
M
U Controllers, Calibrators, Simulators & Pumps
M
U Industrial pH & Conductivity Equipment
DATA ACQUISITION
M
U Data Acquisition & Engineering Software
M
U Communications-Based Acquisition Systems
M
U Plug-in Cards for Apple, IBM & Compatibles
M
U Data Logging Systems
M
U Recorders, Printers & Plotters
HEATERS
M
U Heating Cable
M
U Cartridge & Strip Heaters
M
U Immersion & Band Heaters
M
U Flexible Heaters
M
U Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
M
U Metering & Control Instrumentation
M
U Refractometers
M
U Pumps & Tubing
M
U Air, Soil & Water Monitors
M
U Industrial Water & Wastewater Treatment
M
U pH, Conductivity & Dissolved Oxygen Instruments
M3906/0919
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising