Omega | DP25-S and DP25B-S | Owner Manual | Omega DP25-S and DP25B-S Owner Manual

Omega DP25-S and DP25B-S Owner Manual
5
Scaling With Known Loads
6
(Continued)
Scaling Without Known Loads (Continued)
6. Press MENU to store IN!1. The unit displays:
3. Press /TARE again. The unit displays the
last setting for IN!1.
(The first digit flashes.)
7. Press /TARE. The unit displays the last setting for RD!1.
4. Change IN!1 as necessary:
• Press /NT/GRS to set or change the digit's current value. Continue
to press /NT/GRS until the meter displays the desired value for the
flashing digit. Values can range from 0 to 9. For the first digit, you can
also enter a minus sign (–) or –1.
• Press /TARE to scroll to the digit(s) you want to change.
8. Change RD!1 as necessary:
• Press /TARE to scroll to the digit(s) you want to change
(it flashes on the display).
• Press /NT/GRS to change the value of the flashing digit.
Values can range from 0 to 9. For the first digit, you can also
enter a minus sign (–) or –1.
9. Press MENU to store the value shown for RD!1.
The unit displays:
To identify the maximum known load (IN!2 and RD!2 ):
1. Apply the maximum known load (100%).
5. Press MENU to store IN!1. The unit displays:
6. Press /TARE. The unit displays the last
setting for RD!1. (The first digit flashes.)
7. Change RD!1 as necessary:
• Press /NT/GRS until the meter displays the desired value for
the flashing digit. Values can range from 0 to 9. For the first digit,
you can also enter a minus sign (–) or –1.
• Press /TARE to scroll to the digit(s) you want to change.
8. Press MENU to store the value shown for RD!1.
The unit displays:
2. Repeat steps 4–9 above, for IN!2 and RD!2.
Once you've completed all steps, the unit displays:
To define the maximum load ( IN!2 and RD!2 ):
1. Repeat steps 3–8 above, entering the values for IN!2
and RD!2.
2. Once you've completed all steps, the unit displays:
To begin operation:
Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the display).
When a numeric reading appears, the unit is
operational.
Scaling Without Known Loads
For 0–100 mV sensors, the values for the minimum and maximum
input loads are always as follows:
• Minimum load ( IN!1 ) — 0
• Maximum load ( IN!2 ) — 9999.
If your installation uses a different sensor type, you must calculate
the values for IN!1 and IN!2 before proceeding with the steps
below. Use the formula provided in the Operator's Manual.
To define the minimum load ( IN!1 and RD!1 ):
1. If it's not already shown, press MENU until
the unit displays:
2. Press /TARE. The unit displays:
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects
in materials and workmanship for a period of 61 months from
date of purchase. OMEGA’s WARRANTY adds an additional one (1)
month grace period to the normal five (5) year product warranty
to cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized
Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it
will be repaired or replaced at no charge. OMEGA’s WARRANTY does
not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation
outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of having been damaged as a
result of excessive corrosion; or current, heat, moisture or vibration;
improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear
is not warranted, include but are not limited to contact points, fuses,
and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any
damages that result from the use if its products in accordance
with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by
the company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set
forth herein are exclusive, and the total liability of OMEGA
with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC),
used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with
any nuclear installation or activity, medical application, used on humans,
or misused in any way, OMEGA assumes no responsibility as set forth
in our basic WARRANTY/DISCLAIMER language, and, additionally,
purchaser will indemnify OMEGA and hold OMEGA harmless from any
liability or damage whatsoever arising out of the use of the Product(s)
in such a manner.
For complete product manual:
www.omega.com/manuals/manualpdf/M3598.pdf
TM
DP25B-S
Strain Gage Panel Meter
RETURN REQUESTS/INQUIRIES
To begin operation:
Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the
display). When a numeric reading appears,
the unit is operational.
Determining Reading Offset
The run mode reading for meters scaled without known loads may
reflect an offset. For example, say you set RD!1 to 0 and RD!2 to
100, but when the minimum load is applied, a negative value of –1.5
displays on the front panel.
To correct the reading offset:
1. With zero load applied, note the reading on the display.
2. Subtract that amount from the RD!1 and RD!2 values you originally entered.
In the example, the offset would be –1.5. If RD!1 is to read 0 in
Run Mode, it must be reentered as 1.5. RD!2 must likewise be
reentered as 101.5 if the meter is to read 100 when the maximum load is applied.
3. Repeat the steps for "Scaling Without Known Loads," but when
the values for IN!1 and IN!2 display, do not change them.
Instead, press MENU to move to the prompts for RD!1 and RD!2
and make the necessary changes.
4. Reinitialize the unit and resume operation.
Direct all warranty and repair requests/inquiries to the OMEGA
Customer Service Department.
BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
FOR WARRANTY RETURNS,
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number
under which the product
was PURCHASED,
2. Model and serial number of the
product under warranty, and
3. Repair instructions and/or
specific problems relative
to the product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover
the COST of the repair or
calibration,
2. Model and serial number of the
product, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers
the latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable
form, in whole or in part, without the prior written consent of OMEGA
ENGINEERING, INC.
MQS3598/0918
omega.com info@omega.com
Servicing North America:
U.S.A.
Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patientconnected applications.
This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains
important information relating to safety and EMC.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OMEGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without
notice.
2
START HERE
Using This Quick Start Manual
Wiring
(continued)
Use this Quick Start Manual to set up your Strain Meter and begin operation.
Information is provided on how to:
• Connect ac power
• Set basic options for operation
Connect the sensor
• Scale the meter.
IMPORTANT: For complete information on all setup options, please
refer to the Operator’s Manual.
Safety Consideration
This device is marked with the international Caution symbol.
The instrument is a panel mount device protected in accordance with
2014/35/EU, electrical safety requirements for electrical equipment for
measurement, control and laboratory. Remember that the unit has no
power-on switch. Building installation should include a switch or circuitbreaker that must be compliant to IEC 947-1 and 947-3.
SAFETY:
• Do not exceed voltage rating on the label located on the top of the instrument
housing.
• Always disconnect power before changing signal and power connections.
• Do not use this instrument on a work bench without its case for safety
reasons.
• Do not operate this instrument in flammable or explosive atmospheres.
• Do not expose this instrument to rain or moisture.
EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the instrument if EMC problems
persist.
When using DC power, do not use internal excitation or Isolated
Analog Output for high color brightness. For low or medium
brightness, internal excitation is limited to 24 V @ 25 mA; 5 V, 10
V, 12 V @ 35 mA.
In order to maintain the same degree of protection as the AC units,
always use a Safety Agency Approval DC source with the same
Overvoltage Category and Pollution Degree.
DC Powered Unit Connections
Connect the Sensor
1. Locate the TB2 connector on the rear of the unit.
2. Attach the sensor wires and tighten the lockdown screws.
The diagram below shows the wiring for bridge sensors with internal
excitation.
Refer to the Operator’s Manual for setup requirements for other
sensor types.
4
Using the Configuration Menu
MENU
INPT
DEC.P
RD.S.O
RD.CF
Features with
are for the “B” version which has three-color
programmable “Big” LED display - All segment characters shown are for
the “B” version.
This Quick Start Manual includes specific configuration parameters for bridge sensors with an output range of 0–100 mV and
10 V excitation. Other sensor types may require different
parameters or additional ones. When this is the case, we refer
you to the Operator's Manual for detailed instructions.
3
SUBMENU
/TARE
100M, ±50M, !10V, !±5V, 0-20 *
FFFF *, F.FFF, FF.FF, FFF.F
IN!1, RD!1, IN!2, RD!2
R.1=T *, R.1=N
R.2=0, R.2=1, R.2=2, R.2=3, R.2=4 *
R.3=F *, R.3=U
R.4=P, R.4=G
COLR GRN, RED, AMBR
S1.CF S.1=A *, S.1=B
S.2=U *, S.2=L
S.3=N*, S.3=G shown if R.4=G
S2.CF S.1=A *, S.1=B
S.2=U *, S.2=L
S.3=N*, S.3=G shown if R.4=G
S1.DB 0003 *
S2.DB 0003 *
OT.CF O.1=E *, 0.1=D
O.2=C *, 0.2=V
O.3=A *, 0.3=P
OT.S.O RD!1, OUT1, RD!2, OUT2
LK.CF RS=E *, RS=D
SP=E *, SP=D
L3=0 *, L3=1
BRIT M.BrT, .BrT, H.BrT
(continued)
DESCRIPTION
Input
Decimal Point
Scale and Offset
Reading Configuration
1. Remove the panel at the back of the unit.
2. Locate the TB1 connector.
3. Insert the correct wire in each terminal as shown in the following figure
and tighten the lockdown screws.
4. Tug gently on the wires to verify the connections.
External Fuse Required:
Time-delay, UL 248-14 listed Time-lag, IEC 127-3 recognized
175 mA (115 Vac line)
125 mA (115 Vac line)
80 mA (230 Vac line)
63 mA (230 Vac line)
Setpoint 2 Configuration
Setpoint 1, Deadband
Setpoint 2, Deadband
Analog Output
Configuration
Output Scale & Offset
Lockout Configuration
Display Brightness
To Set the Input Type
1. Press MENU until the unit displays:
4. Press MENU to select the decimal point position shown. The
unit displays:
You can scale the meter in one of two ways:
1. With a known load — This method uses input (load) information
sent from another device such as a scale or a simulator for
voltage or current.
2. Without a known load — This involves calculating the load
based on transducer specifications and manually entering it to
the meter.
For both methods, you must first identify the minimum input load
IN!1 and the corresponding display reading you want RD!1. Then
you identify the maximum input load IN!2 and its corresponding
display reading RD!2.
The decimal point is for display purposes only — you set it
where you want it to display for your application.
When entering IN!1 and IN!2 values, ignore any decimal
point on the display. However, you must enter RD!1 and
RD!2 values with the decimal point in the desired position.
Scaling With Known Loads
To identify the minimum known load ( IN!1 and RD!1 ):
2. Press /TARE. The unit displays:
Bridge Sensor with Internal Excitation
1. If it's not already shown, press MENU until the unit displays:
3. Tug gently on the wires to verify the connections.
4. Replace the panel at the back of the unit.
Using the Configuration Menu
To configure the meter, you use the buttons on the front panel.
To:
Display the
Configuration Menu
Select a submenu
function
Select a value
for that submenu
function
Go back to previous
menu function
Exit the
Configuration
Menu
AC Powered Unit Connections
3. Press /NT/GRS to move the decimal point to
the desired location. The factory settings is
FFFF. The other choices are F.FFF, FF.FF,
and FFF.F.
To Scale the Meter
* Factory Default Settings
Wiring
Warning: Do not connect AC power to your device until you
have completed all input and output connections. This device
must only be installed by a specially trained electrician with
corresponding qualifications. Failure to follow all instructions
and warnings may result in injury!
(continued)
Display Color
Setpoint 1 Configuration
Mount the Unit
1. Cut a panel opening using the dimensions shown to the right.
2. Position the unit in the opening, making
sure the front bezel is flush with the
panel.
3. Install retaining clips on both sides of
the meter and tighten against the panel.
To Set the Decimal Point
Take This Action:
Press the MENU button. The first function
on the menu, INPT, displays.
1.
Press MENU until the function you
want is shown.
2.
Press /TARE.
The information you can change flashes.
1.
Press /NT/GRS to display the option
you want.
2.
Press MENU to store it.
STRD quickly flashes, indicating that
the selection has been stored in memory.
Then the next menu function displays.
Press RESET once.
Press RESET twice. The unit displays
RST as it reinitializes. When a numeric
value displays, the unit is in run mode.
(Optionally, you can press MENU to
move through all the menu functions
until the unit reinitializes.)
3. For this application you want 100M. If 100M is not displayed,
press /NT/GRS until it appears. Other choices are 50M, 10V,
5V and 0-20.
Refer to the Operator's Manual for more information on
changing ranges.
2. Apply the minimum known load (0%).
3. Press /TARE. The unit displays:
4. Press MENU to select the sensor shown. The meter displays the
next menu item. If you changed input type, the meter displays:
4. Press /TARE again. The unit displays the last setting for IN!1.
To Set the Decimal Point
1. If it's not already shown, press MENU until the
unit displays:
5. Press /TARE again. The unit displays the actual reading
being received from the sending device.
2. Press /TARE. The unit displays:
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising