Omega | DP32Pt, DP16Pt, DP8Pt | Owner Manual | Omega DP32Pt, DP16Pt, DP8Pt Owner Manual

Omega DP32Pt, DP16Pt, DP8Pt Owner Manual
For complete product manual:
www.omega.com/manuals/manualpdf/M5460.pdf
DP32Pt, DP16Pt, DP8Pt, DP8EPt
Temperature, Process and Strain Meters
The information contained in this document is believed to
be correct, but OMEGA accepts no liability for any errors it
contains, and reserves the right to alter specifications
without notice.
OMEGA’s policy is to make running changes, not model
changes, whenever an improvement is possible. This
affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA
ENGINEERING, INC. © Copyright 2016 OMEGA
ENGINEERING, INC. All rights reserved. This document
may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable
form, in whole or in part, without the prior written consent of
OMEGA ENGINEERING, INC.
MQS5460/0716
PLATINUMTM Series Meters Quick Start Guide
Introduction
1. Introduction
This PLATINUMTM Series Meters Quick Start Guide provides only a brief overview of each controller’s
functions and quick configurations to get started. Please refer to the PLATINUMTM Series Meters User’s
Guide PDF at Omega.com/manuals for complete information and specifications for each end device.
1.1
Description
The PLATINUMTM Series meter offers unparalleled flexibility in process measurement. While the meter is
extremely powerful and versatile, great care has gone into designing a product that is easy to set up and
use. Automatic hardware configuration recognition eliminates the need for jumpers. The PLATINUMTM
Series meter displays only the menu items associated with the system’s custom configuration.
Each unit allows the user to select the input type from 9 thermocouple types (J, K, T, E, R, S, B, C, and N),
Pt RTDs (100, 500, or 1000 Ω, with a 385, 392, or 3916 curve), thermistors (2250 Ω, 5K Ω, and 10K Ω), DC
voltage, or DC current. The analog voltage inputs may be single ended bipolar, differential absolute or
differential ratiometric and both voltage and current are fully scalable using a single point or 10-point
linearization to virtually all engineering units with a selectable decimal point that is perfect for use with
pressure, flow, or other process inputs. Multiple Alarms can be configured for above, below, hi/lo, and
band triggering using either absolute or deviation Alarm trigger points.
The PLATINUMTM Series meter features a large, three-color, programmable display with the capability to
change color every time the Alarm is triggered. Various configurations of mechanical relay, SSR, DC
pulse, and isolated or non-isolated analog voltage or current outputs are available. Every unit comes
standard with USB communications for firmware updates, configuration management, and data
transfer. Optional Ethernet and RS-232 / RS-485 Serial communications are also available. The Analog
Output is fully scalable and may be configured for retransmission to follow your input signal. The
universal power supply accepts 90–240 Vac. The low-voltage power option accepts 24 Vac or 12–36 Vdc.
Additional features usually found only on more expensive meters make these the most powerful
products in their class. Some additional standard features are High-high/Low-low Alarm functionality,
external latch reset, configuration save and transfer, and configuration password protection.
2
PLATINUMTM Series Meters Quick Start Guide
Safety Considerations
2. Safety Considerations
This device is marked with the international caution symbol. It is important to read this manual before
installing or commissioning this device as it contains important information relating to Safety and EMC
(Electromagnetic Compatibility).
This instrument is a panel mount device protected in accordance with 2014/35/EU, electrical safety
requirements for electrical equipment for measurement, control, and laboratory use. Installation of this
instrument should be done by qualified personnel.
In order to ensure safe operation, the following instructions must be followed and warnings
observed:
This instrument has no power-on switch. An external switch or circuit-breaker must be included in the
building installation as a disconnecting device. It must be marked to indicate this function, and it must
be in close proximity to the equipment within easy reach of the operator. The switch or circuit-breaker
must comply with the relevant requirements of IEC 947–1 and IEC 947-3 (International Electro technical
Commission). The switch must not be incorporated in the main supply cord.
Furthermore, to provide protection against excessive energy being drawn from the main supply in case
of a fault in the equipment, an overcurrent protection device must be installed.







Do not exceed the voltage rating on the label located on the top of the instrument housing.
Always disconnect the power before changing the signal and power connections.
Do not use this instrument on a work bench without its case for safety reasons.
Do not operate this instrument in flammable or explosive atmospheres.
Do not expose this instrument to rain or moisture.
Unit mounting should allow for adequate ventilation to ensure that the instrument does not
exceed the operating temperature rating.
Use electrical wires with adequate size to handle mechanical strain and power requirements.
Install this instrument without exposing the bare wire outside the connector to minimize
electrical shock hazards.
EMC Considerations




Whenever EMC is an issue, always use shielded cables.
Never run signal and power wires in the same conduit.
Use signal wire connections with twisted-pair cables.
Install Ferrite Beads on signal wires close to the instrument if EMC problems persist.
Failure to follow all instructions and warnings is at your own risk and may result in property
damage, bodily injury and/or death. Omega Engineering is not responsible for any damages
or loss arising or resulting from any failure to follow any and all instructions or observe any
and all warnings.
3
PLATINUMTM Series Meters Quick Start Guide
Wiring Instructions
3. Wiring Instructions
3.1
Back Panel Connections
Ethernet Connector if EIP Option Installed
Ethernet Communications Status
LEDs if EIP Option Installed
USB Connector
8-Pin Power / Outputs Connector
10-Pin Input Connector
Figure 1 – DP8Pt and DP8EPt Models: Back Panel Connections
(No Isolated Output Expansion Board Installed)
8-Pin Power / Outputs Connector
Ethernet Connector if EIP
Option Installed
Ethernet Communications Status
LEDs if EIP Option Installed
10-Pin Input Connector
USB Connector
Figure 2 – DP16Pt and DP32Pt Models: Back Panel Connections
(With Isolated Output Expansion Board)
4
PLATINUMTM Series Meters Quick Start Guide
3.2
Wiring Instructions
Connecting Power
Connect the main power connections to pins 7 and 8 of the 8-pin power / output connector as shown in
Figure 3.
110 - 300 Vdc
110 ~ 300 Vdc
Use Copper Conductors only
(rated for 75 C min.)
for Power Connections
Caution: Do not connect power to your device until you have completed all input
and output connections. Failure to do so may result in injury!
Figure 3 – Main Power Connections
For the low-voltage power option, maintain the same degree of protection as the standard highvoltage input power units (90–240 Vac) by using a Safety Agency Approved DC or AC source with
the same Overvoltage Category and pollution degree as the standard AC unit (90–300 Vac).
The Safety European Standard 2014/35/EU for measurement, control, and laboratory equipment
requires that fuses must be specified based on IEC127. This standard specifies the letter code “T”
for a Time-lag fuse.
5
PLATINUMTM Series Meters Quick Start Guide
3.3
Wiring Instructions
6
Connecting Inputs
The 10-pin input connector assignments are summarized in Table 1. Table 2 summarizes the universal
input pin assignments for different sensor inputs. All sensor selections are firmware-controlled and no
jumper settings are required when switching from one type of sensor to another. Figure 4 provides
more detail for connecting RTD sensors. Figure 5 shows the connection scheme for process current
input with either internal or external excitation.
Table 1 – 10-Pin Input Connector Wiring Summary.
Pin No.
Code
1
2
3
ARTN
AIN+
AIN-
4
5
6
7
8
9
APWR
AUX
EXCT
DIN
ISO GND
RX/A
10
TX/B
Description
Analog return signal (analog ground) for sensors
Analog positive input
Analog negative input
Analog power currently only used for 4-wire RTDs
Only used with controller models
Excitation voltage output referenced to ISO GND
Digital input signal (latch reset), Positive at > 2.5V, ref. to ISO GND
Isolated ground for serial communications, excitation, and digital input
Serial communications receive
Serial communications transmit
Table 2 – Interfacing Sensors to the Input Connector.
Pin
Number
1
2
3
4
Diff
Voltage
Vin +/Vd +/-
Process
Voltage
Process
Current
Rtn
Vin +/-
5
** Requires external connection to pin 4
I+
I-
Thermocouple
T/C+
T/C-
2-Wire
RTD
3-Wire
RTD
4-Wire
RTD
**
RTD1+
RTD2RTD1+
RTD1-
RTD1-
RTD2+
RTD1+
RTD2RTD1-
Thermistor
Remote
Setpoint
Rtn(*)
TH+
THV/I In
PLATINUMTM Series Meters Quick Start Guide
1
2
3
4
5
6
7
Wiring Instructions
8
9
10
RTD (100 Ω) 4-WIRE
RTD (100 Ω) 3-WIRE
RTD (100 Ω) 2-WIRE (requires
pin 1 to be jumped to pin 4)
Figure 4 – RTD Wiring Diagram
0–24 mA
Internal
Excitation
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
9
10
External
Excitation
Internal
Figure 5 – Process Current Wiring Hookup with Internal and External Excitation
1
2
3
4
5
6
7
8
9
10
1
2
3
4
+/- 10, +/- 1 and +/- 0.1
Single End Voltage
V
5
6
7
8
+/- 0.1and +/- .05 Differential /
Ratiometric Voltage
V
Reference Voltage
Figure 6 – Process Voltage Wiring Hookup with optional Ratiometric Voltage connection.
7
PLATINUMTM Series Meters Quick Start Guide
3.4
Wiring Instructions
8
Connecting Outputs on Units with Alarm Relays
The PLATINUMTM Series Meters can be configured with two alarm only Single Pole Double Throw
Mechanical Relays. This is the “-330” option and these SPDT relays have snubbers built in but only on
the normally open contact side.
Table 3 – 8 Pin Output/Power Connector Wiring Summary by Configuration.
Power
Config.
-330
Output Pin Number
Description
8
7
6
5
4
3
2
1
Base Meter – No Outputs
AC+
or
DC+
ACor
DC-
N.O
Com
N.C
N.O
Com
N.C
SPDT, SPDT
Table 4 – Definitions for Abbreviations in Table 3.
Code
N.O.
Com
N.C.
Definition
Normally open relay/SSR load
Relay Common/SSR AC power
Normally closed relay load
Code
Definition
ACAC+
DCDC+
AC power neutral in pin
AC power hot in pin
Negative DC power in pin
Positive DC power in pin
PLATINUMTM Series Meters Quick Start Guide
PLATINUMTM Series Navigation
4. PLATINUMTM Series Navigation
Alarm Annunciators
Negative Sign
Process Value
Temperature Units
Program Buttons
Setpoint Value
Process Value
Temperature Units
Alarm Annunciators
Program Buttons
Figure 7 – PLATINUMTM Series Displays (DP8Pt and DP8EPt Shown)
4.1
Description of Button Actions
The UP button moves up a level in the menu structure. Pressing and holding the UP
button navigates to the top level of any menu (oPER, PRoG, or INIt). This can useful if
you get lost in the menu structure.
The LEFT button moves across a set of menu choices at a given level (up in the Section 4
menu structure tables). When changing numerical settings, press the LEFT button to
make the next digit (one digit to the left) active.
The RIGHT button across a set of menu choices at a given level (down in the Section 4
menu structure tables. The RIGHT button also scrolls numerical values up with overflow
to 0 for the flashing digit selected.
The ENTER button selects a menu item and goes down a level, or it enters a numerical
value or parameter choice.
4.2 Menu Structure
The menu structure of the PLATINUMTM Series is divided into 3 main Level 1 groups, which are
Initialization, Programming, and Operating. They are described in Section 4.3. The complete menu
structure for levels 2-8 for each of the three Level 1 groups is detailed in Section 5.1, 5.2, and 5.3.
Levels 2 through 8 represent sequentially deeper levels of navigation. Values with a dark box around
them are default values or submenu entry points. Blank lines indicate user-provided information. Some
menu items include links to reference information elsewhere in this user manual. The information in the
Notes column defines each menu choice.
9
PLATINUMTM Series Meters Quick Start Guide
4.3
PLATINUMTM Series Navigation
Level 1 Menu
INIt
Initialization Mode: These settings are rarely changed after initial setup. They include
transducer types, calibration, etc. These settings can be password-protected.
PRoG
Programming Mode: These settings are frequently changed. They include Setpoints,
Control Modes, Alarms, etc. These settings can be password-protected.
oPER
Operating Mode: This mode allows users to switch between Run Mode, Standby Mode,
Manual Mode, etc.
4.4
Circular Flow of Menus
The following diagram shows how to use the LEFT and RIGHT buttons to navigate around a menu.
Press the ENTER button on
oPER to select and enter RUN
Mode.
oPER
Press the UP button to
navigate back up a level.
It is possible to cycle through
any menu in both directions.
Press the LEFT and RIGHT
buttons to navigate around
the Operating Mode options.
RUN
Stby
SP1
PEAk
SP2
VALy
L.RST
Figure 8 – Circular Flow of Menus.
10
PLATINUMTM Series Meters Quick Start Guide
Complete Menu Structure
5. Complete Menu Structure
5.1
Initialization Mode Menu (INIt)
The following table maps the Initialization Mode (INIt) navigation:
Level
2
Level
3
Level
4
INPt
t.C.
k
J
t
E
N
R
S
b
C
N.wIR
Rtd
A.CRV
tHRM
PRoC
2.25k
5k
10k
4–20
0–24
+-10
+-1
Level
5
Level
6
Level
7
Level
8
Notes
Type K thermocouple
Type J thermocouple
Type T thermocouple
Type E thermocouple
Type N thermocouple
Type R thermocouple
Type S thermocouple
Type B thermocouple
Type C thermocouple
3 wI
3-wire RTD
4 wI
4-wire RTD
2 wI
2-wire RTD
385.1
385 calibration curve, 100 Ω
385.5
385 calibration curve, 500 Ω
385.t
385 calibration curve, 1000 Ω
392
392 calibration curve, 100 Ω
3916
391.6 calibration curve, 100 Ω
2250 Ω thermistor
5000 Ω thermistor
10,000 Ω thermistor
Process input range: 4 to 20 mA
Note: This Manual and Live Scaling submenu is the same for all PRoC ranges.
MANL
Rd.1
____
Low display reading
IN.1
____
Manual input for Rd.1
Rd.2
____
High display reading
IN.2
____
Manual input for Rd.2
LIVE
Rd.1
____
Low display reading
IN.1
____
Live Rd.1 input, ENTER for current
Rd.2
____
High display reading
IN.2
____
Live Rd.2 input, ENTER for current
Process input range: 0 to 24 mA
Process input range: -10 to +10 V
Note: +- 1.0 and +-0.1 support SNGL, dIFF and RtIO tYPE
tYPE
SNGL
Process input range: -1 to +1 V
dIFF
Differential between AIN+ and AIN-
11
PLATINUMTM Series Meters Quick Start Guide
Level
2
Level
3
Level
4
Level
5
Level
6
RtLO
+-0.1
+-.05
tARE
LINR
dSbL
ENbL
RMt
N.PNt
MANL
LIVE
RdG
dEC.P
°F°C
d.RNd
FLtR
ANN.n
NCLR
bRGt
_____
Rd.n
IN.n
Rd.n
IN.n
FFF.F
FFFF
FF.FF
F.FFF
°C
°F
NoNE
_____
8
16
32
64
128
1
2
4
ALM.1
ALM.2
oUt#
GRN
REd
AMbR
HIGH
Complete Menu Structure
Level
7
Level
8
Notes
Ratiometric between AIN+ and AINProcess input range: -0.1 to +0.1 V
Note: The +- 0.05 input supports dIFF and RtIO tYPE
tYPE
dIFF
Differential between AIN+ and AINRtLO
Ratiometric between AIN+ and AINProcess input range: -0.05 to +0.05 V
Disable tARE feature
Enable tARE on oPER menu
Enable tARE on oPER and Digital Input
Specifies the number of points to use
Note: The Manual / Live inputs repeat from 1..10, represented by n
____
Low display reading
____
Manual input for Rd.n
____
Low display reading
____
Live Rd.n input, ENTER for current
Reading format -999.9 to +999.9
Reading format -9999 to +9999
Reading format -99.99 to +99.99
Reading format -9.999 to +9.999
Degrees Celsius annunciator
Degrees Fahrenheit annunciator
Turns off for non-temperature units
Display Rounding
Readings per displayed value: 8
16
32
64
128
2
3
4
Note: Four digit displays offer 2 annunciators, Six digit displays offer 6
Alarm 1 status mapped to “1”
Alarm 2 status mapped to “1”
Output state selections by name
Default display color: Green
Red
Amber
High display brightness
12
PLATINUMTM Series Meters Quick Start Guide
Level
2
Level
3
Level
4
MEd
Low
ECtN
CoMM
5V
10 V
12 V
24 V
0V
USb
EtHN
SER
Level
5
Level
6
Complete Menu Structure
Level
7
Level
8
Notes
Medium display brightness
Low display brightness
Excitation voltage: 5 V
10 V
12 V
24 V
Excitation off
Configure the USB port
Note: This PRot submenu is the same for USB, Ethernet, and Serial ports.
PRot
oMEG ModE
CMd
Waits for commands from other end
CoNt
____ Transmit continuously every ###.# sec
dAt.F
StAt
No
yES
Includes Alarm status bytes
RdNG
yES
Includes process reading
No
PEAk
No
yES
Includes highest process reading
VALy
No
yES
Includes lowest process reading
UNIt
No
yES
Send unit with value (F, C, V, mV, mA)
_LF_
No
yES
Appends line feed after each send
ECHo
yES
Retransmits received commands
No
SEPR
_CR_
Carriage Return separator in CoNt
SPCE
Space separator in CoNt Mode
M.bUS
RtU
Standard Modbus protocol
ASCI
Omega ASCII protocol
AddR
____
USB requires Address
PRot
Ethernet port configuration
AddR
____
Ethernet “Telnet” requires Address
PRot
Serial port configuration
C.PAR bUS.F
232C
Single device Serial Comm Mode
485
Multiple devices Serial Comm Mode
bAUd
19.2
Baud rate: 19,200 Bd
9600
9,600 Bd
4800
4,800 Bd
2400
2,400 Bd
13
PLATINUMTM Series Meters Quick Start Guide
Level
2
Level
3
Level
4
Level
5
PRty
dAtA
StoP
SFty
PwoN
RUN.M
SP.LM
LPbk
o.CRk
t.CAL
NoNE
1.PNt
2.PNt
ICE.P
SAVE
LoAd
VER.N
VER.U
F.dFt
I.Pwd
P.Pwd
____
____
1.00.0
ok?
ok?
No
yES
No
yES
AddR
dSbL
ENbL
dSbL
ENbL
SP.Lo
SP.HI
dSbL
ENbL
ENbl
dSbL
R.Lo
R.HI
ok?
dSbL
____
____
____
____
____
____
Level
6
1200
57.6
115.2
odd
EVEN
NoNE
oFF
8bIt
7bIt
1bIt
2bIt
Complete Menu Structure
Level
7
Level
8
Notes
1,200 Bd
57,600 Bd
115,200 Bd
Odd parity check used
Even parity check used
No parity bit is used
Parity bit is fixed as a zero
8 bit data format
7 bit data format
1 stop bit
2 stop bits gives a “force 1” parity bit
Address for 485, placeholder for 232
RUN’s automatically on power up
Power on: oPER Mode, ENTER to run
ENTER in Stby, PAUS, StoP runs
ENTER in modes above displays RUN
Low Setpoint limit
High Setpoint limit
Loop break timeout disabled
Loop break timeout value (MM.SS)
Open Input circuit detection enabled
Open Input circuit detection disabled
Manual temperature calibration
Set offset, default = 0
Set range low point, default = 0
Set range high point, default = 999.9
Reset 32°F/0°C reference value
Clears the ICE.P offset value
Download current settings to USB
Upload settings from USB stick
Displays firmware revision number
ENTER downloads firmware update
ENTER resets to factory defaults
No required password for INIt Mode
Set password for INIt Mode
No password for PRoG Mode
Set password for PRoG Mode
14
PLATINUMTM Series Meters Quick Start Guide
5.2
Complete Menu Structure
Programming Mode Menu (PRoG)
The following table maps the Programming Mode (PRoG) navigation:
Level
2
SP1
SP2
Level Level Level Level
Notes
3
4
5
6
____
Process goal for PID, default goal for oN.oF
ASbo
Setpoint 2 value can track SP1, SP2 is an absolute value
dEVI
SP2 is a deviation value
ALM.1 Note: This submenu is the same for all other Alarm configurations.
tyPE
oFF
ALM.1 is not used for display or outputs
AboV
Alarm: process value above Alarm trigger
bELo
Alarm: process value below Alarm trigger
HI.Lo.
Alarm: process value outside Alarm triggers
bANd
Alarm: process value between Alarm triggers
Ab.dV AbSo
Absolute Mode; use ALR.H and ALR.L as triggers
d.SP1
Deviation Mode; triggers are deviations from SP1
d.SP2
Deviation Mode; triggers are deviations from SP2
CN.SP
Tracks the Ramp & Soak instantaneous setpoint
ALR.H ____
Alarm high parameter for trigger calculations
ALR.L ____
Alarm low parameter for trigger calculations
A.CLR
REd
Red display when Alarm is active
AMbR
Amber display when Alarm is active
GRN
Green display when Alarm is active
dEFt
Color does not change for Alarm
HI.HI
oFF
High High / Low Low Alarm Mode turned off
oN
____
Offset value for active High High / Low Low Mode
LtCH
No
Alarm does not latch
yES
Alarm latches until cleared via front panel
botH
Alarm latches, cleared via front panel or digital input
RMt
Alarm latches until cleared via digital input
CtCL
N.o.
Output activated with Alarm
N.C.
Output deactivated with Alarm
A.P.oN yES
Alarm active at power on
No
Alarm inactive at power on
dE.oN ____
Delay turning off Alarm (sec), default = 1.0
dE.oF ____
Delay turning off Alarm (sec), default = 0.0
oUt2
oUt2 is replaced by output type
oUt3
oUt3 is replaced by output type (1/8 DIN can have up to 6)
PId.S
ACtN RVRS
Increase to SP1 (i.e., heating)
dRCt
Decrease to SP1 (i.e., cooling)
A.to
____
Set timeout time for autotune
AUto
StRt
Initiates autotune after StRt confirmation
15
PLATINUMTM Series Meters Quick Start Guide
Level
2
Level
3
GAIN
Level
4
_P_
_I_
_d_
____
____
ENbL
dSbL
Level
5
____
____
____
Level
6
Complete Menu Structure
Notes
Manual Proportional Band setting
Manual Integral Factor setting
Manual Derivative Factor setting
%Lo
Low clamping limit for Pulse, Analog Outputs
%HI
High clamping limit for Pulse, Analog Outputs
AdPt
Enable fuzzy logic adaptive tuning
Disable fuzzy logic adaptive tuning
RM.SP
oFF
Use SP1, not remote Setpoint
oN
4–20
Remote analog Input sets SP1; range: 4–20 mA
Note: This submenu is the same for all RM.SP ranges.
RS.Lo ____ Min Setpoint for scaled range
IN.Lo
____ Input value for RS.Lo
RS.HI
____ Max Setpoint for scaled range
IN.HI
____ Input value for RS.HI
0–24
0–24 mA
0–10
0–10 V
0–1
0–1 V
M.RMP R.CtL
No
Multi-Ramp/Soak Mode off
yES
Multi-Ramp/Soak Mode on
RMt
M.RMP on, start with digital input
S.PRG ____
Select program (number for M.RMP program), options 1–99
M.tRk RAMP
Guaranteed Ramp: soak pnt must be reached in ramp time
SoAk
Guaranteed Soak: soak time always preserved
CYCL
Guaranteed Cycle: ramp can extend but cycle time can’t
Note: tIM.F does not appear for 6 digit display that use a HH:MM:SS format
tIM.F MM:SS
“Minutes : Seconds” default time format for R/S programs
HH:MM
“Hours : Minutes” default time format for R/S programs
E.ACt
StOP
Stop running at the end of the program
HOLd
Continue to hold at the last soak setpoint at program end
LINk
____
Start the specified ramp & soak program at program end
N.SEG ____
1 to 8 Ramp/Soak segments (8 each, 16 total)
S.SEG ____
Select segment number to edit, entry replaces # below
MRt.# ____ Time for Ramp number, default = 10
MRE.#
oFF
Ramp events on for this segment
oN
Ramp events off for this segment
MSP.# ____ Setpoint value for Soak number
MSt.# ____ Time for Soak number, default = 10
MSE.#
oFF
Soak events off for this segment
oN
Soak events on for this segment
16
PLATINUMTM Series Meters Quick Start Guide
5.3
Complete Menu Structure
Operating Mode Menu (oPER)
The following table maps the Operating Mode (oPER) navigation:
Level
2
RUN
SP1
SP2
MANL
PAUS
StoP
L.RSt
VALy
PEAk
Stby
tARE
Level
3
____
____
M.CNt
M.INP
Level
4
____
____
Notes
Normal Run Mode, process value displayed, SP1 in optional secondary display
Shortcut to change Setpoint 1, current Setpoint 1 value in main display
Shortcut to change Setpoint 2, current Setpoint 2 value in main display
Manual Mode, the RIGHT and LEFT buttons control output, displays M##.#
Manual Mode, the RIGHT and LEFT buttons simulate the input for testing
Pause and hold at current process value, display flashes
Stop controlling, turn off outputs, process value rotating flash, Alarms remain
Clears any latched Alarms; Alarms menu also allows digital input reset
Displays the lowest input reading since the VALy was last cleared
Displays the highest input reading since the PEAk was last cleared
Standby Mode, outputs, and Alarm conditions disabled, displays Stby
TARE option - only available if enabled in INPt
17
PLATINUMTM Series Meters Quick Start Guide
Approvals Information
6. Approvals Information
This product conforms to the EMC: 2014/30/EU (EMC Directive).
Electrical Safety: 2014/35/EU (Low Voltage Directive)
Safety requirements for electrical equipment for measurement, control, and laboratory
Double Insulation; Pollution Degree 2
Dielectric withstand Test per 1 min







Power to Input/Output:
Power to Input/Output 1:
Power to Relays/SSR Output:
Ethernet to Inputs:
Isolated RS232 to Inputs:
Isolated Analog to Inputs:
Analog/Pulse to Inputs:
0F
2300 Vac (3250 Vdc)
1500 Vac (2120 Vdc)
2300 Vac (3250 Vdc)
1500 Vac (2120 Vdc)
500 Vac (720 Vdc)
500 Vac (720 Vdc)
No Isolation
Measurement Category I
Category I includes measurements performed on circuits not directly connected to the Mains Supply
(power). Maximum Line-to-Neutral working voltage is 50Vac/dc. This unit should not be used in
Measurement Categories II, III, and IV.
Transients Overvoltage Surge (1.2 / 50uS pulse)
 Input Power:
2500 V
2
 Input Power :
1500 V
 Ethernet:
1500 V
 Input/Output Signals:
500 V
1F
ADDITIONAL INFORMATION:
FCC: This device complies with Part 15, Subpart B, Class B of the FCC rules, for option –EIP only.
RoHS II: The above product has been declared by the original supplier as Compliant. The manufacturer
of this item declares that the product complies with the EEE RoHS II Directive 2011/65/EC.26.
UL File Number: E209855
1
2
Low-voltage DC power option: Units configured for external low power DC voltage, 12–36Vdc.
Ibid.
18
MQS5460/0716
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising