Omega | DP41-E | Owner Manual | Omega DP41-E Owner Manual

Omega DP41-E Owner Manual
5
Dec pt
Set Default Decimal Point
1. Press MENU. The meter displays:
SETPTS
2. Press /MIN to display the current
decimal point. Change the display, if
necessary, to read “FFFFFF.” (Use
/MAX to change the decimal point
position).
/MAX
/MIN
MENU
RESET
FFFFFF.
SETPTS
/MAX
/MIN
MENU
RESET
3. Press MENU. The meter stores changes (if applicable),
then displays “CNT BY”.
stored
SETPTS
/MAX
/MIN
MENU
CNTBY
RESET
SETPTS
/MAX
/MIN
MENU
RESET
INPUT1
1. Apply 4mA to the input and record the
display reading.
INPUT 1 = _________________
Refer to this as Input One.
WARRANTY/DISCLAIMER
Scale Input Values
1. Press /MIN to display “INPUT 1”:
Press /MIN again. The meter
displays “000000”. Enter the INPUT 1
value recorded in step 1 of the Measure
Input Values section of this quick start.
2. Press MENU. The meter displays
“READ 1”:
Press /MIN to display a six-digit
number. Change the meter to read
“000000”. (Use /MIN to scroll
through digits and /MAX to change
the digit’s value.)
3. Press MENU. The meter displays
“INPUT 2”:
Press /MIN. The meter displays
“000000”. Enter the INPUT 2 value
recorded in step 2 of the Measure Input
Values section of this quick start.
4. Press RESET twice. The meter momentarily displays
“RESET 2” then returns to the run mode. The meter
will now read the input signal (4mA = ≈ 000000.
and 20mA = ≈ 020000.).
Measure and Record Input Values
6
4. Press MENU. The meter displays
“READ 2”:
INPUT1
/MAX
SETPTS
/MAX
/MIN
MENU
RESET
INPUT2
2. Apply 20mA to the input and record the
display reading.
INPUT 2 = _________________
Refer to this as Input Two.
SETPTS
/MAX
/MIN
MENU
RESET
/MAX
SETPTS
RESET
/MIN
MENU
RESET
INPUT2
/MAX
SETPTS
/MIN
MENU
RESET
READ 2
Press /MIN to display a six digit
number. Change the meter to read
“001000”. (Use /MIN to scroll through
digits and /MAX to change the digit’s value.)
/MAX
/MIN
MENU
RESET
5. Press MENU. The meter stores changes and displays:
stored
SETPTS
3. Press MENU until the meter displays:
MENU
READ 1
SETPTS
SETPTS
/MIN
/MAX
/MIN
MENU
RESET
Dec pt
SETPTS
/MAX
/MIN
MENU
RESET
IN CNF
SETPTS
/MAX
/MIN
MENU
RESET
4. Press MENU until the meter displays:
Press /MIN to display “INP6=0”
Change the meter to read “INP.6=1”
(Use /MIN to scroll through digits
and /MAX to change the digit’s value).
INp6=0
SETPTS
/MAX
/MIN
MENU
RESET
6. Press /MIN to display the current decimal point. Press
/MAX to change the decimal point location to “FFFFF.F”.
7. Press MENU. The meter stores this change, then displays
“CNT BY”
stored
SETPTS
/MAX
/MIN
MENU
RESET
CNTBY
SETPTS
/MAX
/MIN
MENU
RESET
5. Press MENU. The meter stores changes and displays:
stored
SETPTS
/MAX
/MIN
MENU
RESET
IN.SC.OF
SETPTS
/MAX
/MIN
MENU
RESET
8. Press RESET twice. The meter displays:
“RESET 2”, then returns to the run
mode. The meter is now scaled to
read 0 to 100.0 for a 4-20 mA input.
REset2
SETPTS
/MAX
/MIN
MENU
OMEGA ENGINEERING, INC. warrants this unit to be free of defects
in materials and workmanship for a period of 61 months from date
of purchase. OMEGA’s WARRANTY adds an additional one (1) month
grace period to the normal five (5) year product warranty to
cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized
Return (AR) number immediately upon phone or written request. Upon
examination by OMEGA, if the unit is found to be defective, it will be
repaired or replaced at no charge. OMEGA’s WARRANTY does not
apply to defects resulting from any action of the purchaser, including
but not limited to mishandling, improper interfacing, operation outside
of design limits, improper repair, or unauthorized modification. This
WARRANTY is VOID if the unit shows evidence of having been tampered
with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components in which wear is not warranted, include
but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for
any omissions or errors nor assumes liability for any damages
that result from the use if its products in accordance with
information provided by OMEGA, either verbal or written.
OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are
exclusive, and the total liability of OMEGA with respect to
this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based.
In no event shall OMEGA be liable for consequential, incidental
or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a “Basic Component” under 10 CFR 21
(NRC), used in or with any nuclear installation or activity; or (2) in
medical applications or used on humans. Should any Product(s) be
used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEGA assumes no
responsibility as set forth in our basic WARRANTY/DISCLAIMER
language, and, additionally, purchaser will indemnify OMEGA and hold
OMEGA harmless from any liability or damage whatsoever arising out
of the use of the Product(s) in such a manner.
For complete product manual:
www.omega.com/manuals/manualpdf/M1297.pdf
DP41-E
High Performance Process Indicator
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER
FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO
AVOID PROCESSING DELAYS). The assigned AR number should then be
marked on the outside of the return package and on any correspondence.
FOR WARRANTY RETURNS,
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number under
which the product was
PURCHASED,
2. Model and serial number of
the product under warranty, and
3. Repair instructions and/or
specific problems relative to
the product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover
the COST of the repair or
calibration,
2. Model and serial number of the
product, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers the
latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in
part, without the prior written consent of OMEGA ENGINEERING, INC.
RESET
MQS1297/0818
omega.com info@omega.com
Servicing North America:
800 Connecticut Ave. Suite 5N01
Norwalk, CT 06854
U.S.A.
Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378
(USA & Canada only)
Engineering Service: 1-800-872-9436
(USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
2
START HERE
Using This Quick Start Manual
Use this Quick Start Manual to get your High Performance Process
Indicator up and running. These instructions use the factory default
settings of current input and 24 Vdc sensor excitation.
The latest complete Communication and Operational Manual as well as
free Software are available at www.omega.com
Wiring a Current Transmitter
Quick Start Setup
Follow these steps to wire a current input sensor with
sensor excitation.
1. Locate connectors P3 & P9 on the right-side-rear of the unit.
2. Attach the wires and tighten the retaining screws. Tug gently on the wires
Quick Start Setup scales your meter to read 0 to 100.0 for a
4 - 20mA input. This setup procedure is actually a series of
short tasks. To complete Quick Start Setup successfully, it
is important to perform all tasks in the order outlined in the
Quick Start Setup.
to verify the connection.
JUMPER
USER
PROVIDED
1.00000
/MAX
SETPTS
/MIN
MENU
RESET
2. Press MENU. The meter stores changes (if applicable)
then displays “RDG.OF”:
INPUT
1. Press MENU until the meter displays:
3
/MAX
/MIN
MENU
stored
RESET
1
N/C
RTN
2
3
4. Replace the rear cover.
Thread the sensor wires through the slots
on the side of the cover. Replace the rear cover screw.
5. Apply ac power once again.
SAFETY:
• Do not exceed voltage rating on the label located on the top of the
instrument housing.
reasons.
Meter Button Descriptions
• Do not operate this instrument in flammable or explosive atmospheres.
• Do not expose this instrument to rain or moisture.
EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the instrument if EMC problems persist.
Press This Button To:
SETPTS
sequentailly recall previous setpoint
settings (run mode only), store new
setpoint values.
MENU
access the configuration program
menus and move from one menu
to the next.
Connect AC Power
1. Remove the rear protective cover and set it aside. The cover is secured with a Phillips-head screw.
2. Locate connector P1 on the bottom-left-rear of the unit.
3. The connector has three screw-down terminals.
Insert the correct wire in each terminal and tighten the lockdown screw. Tug gently on each wire to
verify the connection. Use copper conductors only, minimum 18 AWG
NEUTRAL
EARTH
SETPTS
2. Press /MIN until the meter flashes:
Press MENU and “CURRNT” stops
flashing.
Press /MIN to display a flashing
input range of 4-20mA or 0-20 mA.
Press /MAX until the meter displays
“4-20mA.”
FUSE
SETPTS
/MAX
/MIN
MENU
RESET
stored
SETPTS
/MAX
/MIN
MENU
rdg.CNF
RESET
SETPTS
/MAX
/MIN
MENU
RESET
1. Press /MIN to display “RDG.1”.
Press /MAX until the meter displays
“RDG.1=0”. Selecting “RDG.1=0”
enables direct formatting.
RDG.1=0
SETPTS
/MAX
/MIN
MENU
RESET
change the value of a submenu.
3. Press MENU. The meter stores changes (if applicable),
then displays “RDG SC”:
RDG.2=1
SETPTS
/MAX
/MIN
MENU
RESET
N
SETPTS
/MAX
/MIN
MENU
RESET
000000
SETPTS
/MAX
/MIN
MENU
RESET
4. Press MENU. The meter stores change,
if applicable, then displays “IN CNF”.
CNTBY
stored
/MAX
/MIN
MENU
RESET
SETPTS
/MAX
/MIN
MENU
RESET
SETPTS
/MAX
/MIN
MENU
RESET
Set Default Input Scale and Offset
1. Press /MIN until the meter flashes.
Change the value, if necessary, to read
“INP.6=0” (Use /MIN to scroll
through INP submenu choices and
/MAX to select 0 as the value). Setting
“INP.6=0” disables input scale and offset.
INp.6=0
SETPTS
/MAX
/MIN
MENU
RESET
RESET
2. Press MENU. The meter stores changes, if applicable,
then displays “IN.SC.OF”.
L
stored
move backward one menu (press
once) or exit the configuration
menus (press twice).
RESET
3. Press /MIN to display the offset value.
Change the value, if necessary, to read
“000000” (Use /MIN to scroll
through digits and /MAX to change
the digit’s value).
SETPTS
enter and scroll through a submenu.
/MAX
MENU
Set Up Reading Configuration
2. Press /MIN to display “RDG.2”.
Press /MAX until the meter displays
“RDG.2=1”. Selecting “RDG.2=1”
enables an active decimal point.
/MIN
/MIN
3. Press MENU. The meter stores changes (if applicable),
then displays “RDG.CNF”:
P1
1
2
3
/MAX
CURRNT
Mount the Unit
1. Cut a panel opening using the
dimensions shown to the right.
2. Position the unit in the opening,
making sure the front bezel/
gasket is flush with the panel.
3. From the rear of the panel, slide
the sleeve forward over the case
and up to the panel surface.
4. The panel should now be
sandwiched between the bezelbacked gasket in front and the
sleeve in back.
5. Replace the thumbnuts that secure the sleeve tabs to the case.
Configure the Meter
Use the front panel buttons to access the configuration menus, to either
verify or set the unit values. The function of each button is described below:
• Always disconnect power before changing signal and power connections.
• Do not use this instrument on a work bench without its case for safety
rdg.of
P3
a. Remove ac power.
b. Verify the P1 power and P3 and P9 input connections.
c. Check your power source.
d. Check your signal source.
The instrument is a device protected in accordance with UL
61010:2010 Electrical Safety Requirements for Electrical Equipment for Measurement, Control
and Laboratory. The device has no power-on switch. Installations must include a switch or circuit
breaker that is compliant to IEC 947-1 and 947-3. It must be suitably located to be easily reached
and marked as the disconnecting devise for the equipment.
Use copper conductors only, minimum 20 AWG, UL Rated, for power connection. Insulation must
be rated for at least 85C and 600V.
Caution: Use only provided terminal. Torque all connections 0.4 to 0.5 Nm.
–S
P9
2
Apply ac power. The front panel of the unit flashes R. If it does not:
This device is marked with the international Caution symbol.
EXTERNAL FUSE WIRED
115 Vac IEC127-2/III, 125mA, 250V (Time-Lag)
or UL Slow-Blow, 125mA, 250V
230 Vac IEC127-2/III, 63mA, 250V (Time-Lag)
or UL Slow-Blow, 63mA, 250V
N/C
1
SETPTS
Safety Consideration
Check for proper Earth grounding
in the power distribution system
(single phase).
1. Press /MIN to display the scale factor
value. Change the value, if necessary,
to read “1.00000” (Use /MIN to scroll
through digits and /MAX to change
the digit’s value).
–E
Warning: Do not connect AC power to your device until you have completed
all input and output connections. This device must only be
installed by a specially trained electrician with corresponding qualifications.
Failure to follow all instructions and warnings may result in injury!
PROTECTIVE EARTH GND
GREEN WIRE
+S
(-)
ac power, as listed on meter’s Product/ID
4-20mA input (eg: load cell, calibrator)
1/8” Phillips head screwdriver
1/8” flat blade screwdriver
SWITCH
+E
(4-20mA)
In addition to the unit and related parts, you will need the
following items to set up your unit:
L ~AC LINE
N ~AC NEUTRAL
Set Reading Scale Factor and Reading Offset
Select Input Range
(+)
configuration menus
Before You Begin
Check the serial label on the top of the meter case. The
model number’s last 3 digits indicate if the meter is set up
for voltage or current. C1 - C2 are current ranges and DC1
- DC10 are voltage ranges. This quick start manual uses
the C2 (4 - 20mA) range. If your meter is setup for a
range other than C2, consult the Operator’s manual.
LINE
4
Wiring Example: Current Input with Sensor Excitation
To start your unit you:
• connect ac power
• wire the sensor
• configure the meter, using the front panel buttons and the
•
•
•
•
3
rdg sc
SETPTS
/MAX
/MIN
MENU
RESET
stored
SETPTS
/MAX
/MIN
MENU
RESET
IN.SC.OF
SETPTS
/MAX
/MIN
MENU
RESET
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising