Omega | DP41-TC | Owner Manual | Omega DP41-TC Owner Manual

Omega DP41-TC Owner Manual
5
Press /MAX until the
meter displays the
thermocouple type:
4.
5.
J TC
/MAX /MIN
SETPTS
SETPTS
6.
/MAX /MIN
SETPTS
SETPTS
/MAX /MIN
MENU
1.
SETPTS
/MAX /MIN
MENU
Press MENU until the meter
displays:
2.
and then shows the
current temperature.
Press /MIN until the
meter displays:
/MAX /MIN
SETPTS
RESET
/MAX /MIN
MENU
RESET
SETPTS
STORED
RDG.SC
or
SETPTS
/MAX /MIN
MENU
RESET
RESET2
MENU
/MAX /MIN
MENU
RESET
/MAX /MIN
MENU
RESET
and then shows the
current
temperature.
RESET
RD.SC.OF
SETPTS
/MAX /MIN
Press RESET twice. The meter displays:
SETPTS
SETPTS
/MAX /MIN
MENU
OMEGA ENGINEERING, INC. warrants this unit to be free of defects
in materials and workmanship for a period of 61 months from date
of purchase. OMEGA’s WARRANTY adds an additional one (1) month
grace period to the normal five (5) year product warranty to
cover handling and shipping time. This ensures that OMEGA’s
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation.
OMEGA’s Customer Service Department will issue an Authorized
Return (AR) number immediately upon phone or written request. Upon
examination by OMEGA, if the unit is found to be defective, it will be
repaired or replaced at no charge. OMEGA’s WARRANTY does not
apply to defects resulting from any action of the purchaser, including
but not limited to mishandling, improper interfacing, operation outside
of design limits, improper repair, or unauthorized modification. This
WARRANTY is VOID if the unit shows evidence of having been tampered
with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification;
misapplication; misuse or other operating conditions outside of
OMEGA’s control. Components in which wear is not warranted, include
but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various
products. However, OMEGA neither assumes responsibility for
any omissions or errors nor assumes liability for any damages
that result from the use if its products in accordance with
information provided by OMEGA, either verbal or written.
OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are
exclusive, and the total liability of OMEGA with respect to
this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the
purchase price of the component upon which liability is based.
In no event shall OMEGA be liable for consequential, incidental
or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a “Basic Component” under 10 CFR 21
(NRC), used in or with any nuclear installation or activity; or (2) in
medical applications or used on humans. Should any Product(s) be
used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEGA assumes no
responsibility as set forth in our basic WARRANTY/DISCLAIMER
language, and, additionally, purchaser will indemnify OMEGA and hold
OMEGA harmless from any liability or damage whatsoever arising out
of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Press MENU to enter the value. The meter
displays:
RESET
MENU
CNT BY
Your choices are:
0 = °C, 1 = °F, 2 = °K
MENU
/MAX /MIN
RESET
MENU
RDG.5 =0
Press /MAX to change
the value.
/MAX /MIN
RESET
Press MENU. The meter displays:
STORED
4.
SETPTS
MENU
FFFF.FF
SETPTS
RDG.CNF
SETPTS
4.
/MAX /MIN
RESET
Press MENU until the
meter displays:
3.
DEC PT
Press /MAX to move the
decimal point to the desired
location.
To Set Temperature Units:
2.
RESET
SETPTS
3.
1.
MENU
RESET
Press RESET twice. The meter displays:
RESET2
/MAX /MIN
To Set Decimal Point Position:
RDG.CNF
RESET
MENU
and then shows the
current temperature.
RESET2
Press MENU. The meter displays:
STORED
Press RESET twice. The meter displays:
RESET
MENU
Your choices are J, K, T,
E, N, DNJ, R, S, and B.
5.
WARRANTY/DISCLAIMER
6
RESET
The unit is now up and running.
Direct all warranty and repair requests/inquiries to the OMEGA Customer
Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA,
PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER
FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO
AVOID PROCESSING DELAYS). The assigned AR number should then be
marked on the outside of the return package and on any correspondence.
FOR WARRANTY RETURNS,
please have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number under
which the product was
PURCHASED,
2. Model and serial number of
the product under warranty, and
3. Repair instructions and/or
specific problems relative to
the product.
FOR NON-WARRANTY REPAIRS,
consult OMEGA for current repair
charges. Have the following
information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover
the COST of the repair or
calibration,
2. Model and serial number of the
product, and
3. Repair instructions and/or specific
problems relative to the product.
OMEGA’s policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers the
latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced, translated, or
reduced to any electronic medium or machine-readable form, in whole or in
part, without the prior written consent of OMEGA ENGINEERING, INC.
MQS1296/0818
For complete product manual:
www.omega.com/manuals/manualpdf/M1296.pdf
DP41-TC
High Performance
Temperature Indicator
omega.com info@omega.com
Servicing North America:
800 Connecticut Ave. Suite 5N01
Norwalk, CT 06854
U.S.A.
Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
Using This Quick Start Manual
The latest complete Communication and
Operational Manual as well as free Software
are available at www.omega.com/software .
Before You Begin
You should have the following parts:
•
Meter
•
Panel-mounting gaskets
•
ac Power Connector (orange P1), Input Connectors (2)
(grey -P3 and P9), and rear
protective cover (mounted)
with green Cold Junction
You MUST have
Compensation Board (right
this component.
side).
In addition to the unit and related parts, you will need
the following items to set up your unit:
•
ac power, as listed on meter’s Product/ID label
•
Thermocouple
•
1/8” flat blade screwdriver
•
1/8” Phillips head screwdriver
Safety Consideration
This device is marked with the
international Caution symbol.
The instrument is a device protected in accordance with UL
61010:2010 Electrical Safety Requirements for Electrical
Equipment for Measurement, Control and Laboratory. The
device has no power-on switch. Installations must include a
switch or circuit breaker that is compliant to IEC 947-1 and
947-3. It must be suitably located to be easily reached and
marked as the disconnecting devise for the equipment.
Use copper conductors only, minimum 20 AWG,
UL Rated, for power connection. Insulation must be rated for
at least 85C and 600V.
SAFETY:
• Do not exceed voltage rating on the label located on the
top of the instrument housing.
• Always disconnect power before changing signal and
power connections.
• Do not use this instrument on a work bench without
its case for safety reasons.
• Do not operate this instrument in flammable or explosive
atmospheres.
• Do not expose this instrument to rain or moisture. EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the
instrument if EMC problems persist.
Mount the Unit
1. Cut a panel
opening using the dimensions
shown to the right.
2. Position the unit in
the opening,
making sure the
front bezel/ gasket
is flush with the
panel.
3. From the rear of
the panel, slide the sleeve forward over the case and up to
the panel surface.
4. The panel should now be sandwiched between the bezelbacked gasket in front and the sleeve in back.
5. Replace the thumbnuts that secure the sleeve tabs
to the case.
Connect ac Power
Warning: Do not connect AC power to your
device until you have completed all input and
output connections. This device must only be
installed by a specially trained electrician with
corresponding qualifications. Failure to follow
all instructions and warnings may result in
injury!
1. Remove the rear protective cover and set it aside. The
cover is secured with a Phillips-head screw.
2. Locate connector P1 on the bottom-left-rear of the unit.
The connector has three screw-down terminals (see
below).
EXTERNAL FUSE WIRED
115 Vac IEC127-2/III, 125mA, 250V (Time-Lag)
or UL Slow-Blow, 125mA, 250V
230 Vac IEC127-2/III, 63mA, 250V (Time-Lag) or
UL Slow-Blow, 63mA, 250V
3
4
3. Insert the correct wire in each terminal and tighten
the lockdown screw. Tug gently on each wire to
verify the connection. Use copper conductors
only, minimum 20 AWG
Configure the Unit
Press the front panel buttons:
Press This Button: To:
NEUTRAL
EARTH
LINE
access the configuration
menus and move from one
menu to the next.
FUSE
L ~AC LINE
N ~AC NEUTRAL
P1
PROTECTIVE EARTH GND
GREEN WIRE
SWITCH
1
2
3
L
Use this Quick Start Manual to get your Temperature
Indicator, when used with a Thermocouple, up and
running right out of the box. To do this you:
•
connect ac power
•
connect the Thermocouple
•
configure the unit
– specify Thermocouple type
– set degrees to C or F
– set decimal point position
2
MENU
N
START HERE
enter and scroll through a
submenu
Check for proper Earth grounding
in the power distribution system (single phase).
/MIN
CAUTION: Take care not to damage the
green Cold Junction Compensation
Board and its connectors.
change the value of a
submenu
/MAX
4. Replace the rear cover. Verify proper seating of
the connectors on the green Cold Junction
Compensation Board.
5. Thread the power wires through the slots on the side
of the cover. Replace the rear cover retaining screw.
Connect the Thermocouple
Regardless of thermocouple type, the
RED wire is always NEGATIVE.
move backward one menu
(press once) or exit the
configuration menus (press
twice).
RESET
To Set Thermocouple Type:
1.
Press MENU until the
meter displays:
+E
1
+
J1
+S
INPUT
SETPTS
/MAX /MIN
MENU
RESET
MENU
RESET
P9
2
–S
3
TC
–
T/C COLD
JUNCTION
COMPENSATION
BOARD
METER
J2
2.
–E
1
+R
P3
Press /MAX until the
meter flashes:
TC
2
–R
SETPTS
3
The cover on the thermocouple connector shows the
positive and negative terminals.
1. Attach the wires and tighten the retaining screws.
Tug gently on each wire to verify the connection.
2. Apply ac power. The front panel of the unit
displays RESET2, followed by the temperature.
If it does not:
a. Remove ac power.
b. Verify your P1 power connections.
c. Check your power source.
d. Plug the unit in again.
If the unit flashes +OPEN, the Cold Junction Compensation Board is not seated properly. Check the connections
and the rear cover retaining screw, and repeat this step.
3.
/MAX /MIN
Press MENU until the meter displays:
STORED
SETPTS
/MAX /MIN
MENU
RESET
TC
SETPTS
/MAX /MIN
MENU
RESET
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising