Omega | DRST-AC | Owner Manual | Omega DRST-AC Owner Manual

Omega DRST-AC Owner Manual
TM
User’s Guide
Shop online at
omega.com
e-mail: info@omega.com
For latest product manuals:
www.omegamanual.info
DRST-AC
Din Rail AC Transmitter
omega.com info@omega.com
U.S.A.
Headquarters:
Servicing North America:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves
the right to alter specifications without notice.
Table of
Contents
DRST-AC MV Transmitter
Table of Contents
Section .........................................................................
Section 1
Section 2
Section 3
Section 4
Page
Warning ........................................................................................... 5
Safety Instructions ......................................................................... 6
How to demount DRST Series .................................................... 7
Universal AC/DC transmitter ...................................................... 8
Section 4.2 Application ................................................................... 8
Section 4.3 Technical characteristics ............................................. 8
Section 4.4 Mounting / installation / programming ................. 8
Section 5 Signals/Connection ....................................................................... 9
Section 5.1 Input Signals ................................................................ 9
Section 5.2 Output Signals ............................................................. 9
Section 5.3 Power Connection ....................................................... 9
Section 6 DRSL-DISPLAY/programming front ...................................... 10
Section 8.1 Mounting / demounting the DRSL-DISPLAY ..... 10
Section 7 Order ........................................................................................ 11-13
Section 7.1 Specifications .............................................................. 13
Section 8 Configurable input error indication & input limits ........ 14-15
Section 9 DRSL-DISPLAY display readout .............................................. 16
Section 10 Connections .................................................................................. 17
Section 11 Block Diagram .............................................................................. 18
Section 12 Configuration / Operating the function keys ......................... 19
Section 13 Routing Diagram .................................................................... 21-26
Section 13.2 Advanced settings ................................................... 25
Section 13.3 Help text overview .................................................. 25
Section 13.4 Document history .................................................... 26
3
6 Product Pillars
to meet your every need
Individually outstanding, unrivalled in combination
With our innovative, patented technologies, we make signal conditioning smarter and simpler. Our portfolio is composed
of six product areas, where we offer a wide range of analog and digital devices covering over a thousand applications in
industrial and factory automation. All our products comply with or surpass the highest industry standards, ensuring
reliability in even the harshest of environments and have a 5-year warranty for greater peace of mind.
Our range of temperature transmitters and sensors provides the highest level of signal integrity from the
measurement point to your control system. You can convert industrial process temperature signals to analog,
bus or digital communications using a highly reliable point-to-point solution with a fast response time,
automatic self-calibration, sensor error detection, low drift, and top EMC performance in any environment.
We deliver the safest signals by validating our products against the toughest safety standards. Through our
commitment to innovation, we have made pioneering achievements in developing I.S. interfaces with SIL 2 Full
Assessment that are both efficient and cost-effective. Our comprehensive range of analog and digital
intrinsically safe isolation barriers offers multifunctional inputs and outputs, making Omega an easy-toimplement site standard. Our backplanes further simplify large installations and provide seamless integration
to standard DCS systems.
We provide inexpensive, easy-to-use, future-ready communication interfaces that can access your installed base
of products. The detachable DRSL-DISPLAY Local Operator Interface (LOI) allows for local monitoring of
process values, device configuration, error detection and signal simulation. The next generation, our DRST-CM
Remote Operator Interface (ROI) does all that and more, adding remote digital communications via Modbus/
RTU, while the analog output signals are still available for redundancy.
With the DRST-CM you can further expand connectivity with a gateway, which connects via industrial
Ethernet, wirelessly through a Wi-Fi router.
Our unique range of single devices covering multiple applications is easily deployable as your site standard.
Having one variant that applies to a broad range of applications can reduce your installation time and training,
and greatly simplify spare parts management at your facilities. Our devices are designed for long-term signal
accuracy, low power consumption, immunity to electrical noise and simple programming.
Our compact, fast, high-quality 6 mm isolators are based on microprocessor technology to provide exceptional
performance and EMC-immunity for dedicated applications at a very low total cost of ownership. They can be
stacked both vertically and horizontally with no air gap separation between units required.
Our display range is characterized by its flexibility and stability. The devices meet nearly every demand for
display readout of process signals, and have universal input and power supply capabilities. They provide a realtime measurement of your process value no matter the industry, and are engineered to provide a user-friendly
and reliable relay of information, even in demanding environments.
1
Warning
WARNING
GENERAL
This device is designed for connection to hazardous electric voltages. Ignoring this
warning can result in severe personal injury or mechanical damage.
To avoid the risk of electric shock and fire, the safety instructions of this guide must be
observed and the guidelines followed. The specifications must not be exceeded, and
the device must only be applied as described in the following.
Prior to the commissioning of the device, this installation guide must be examined
carefully.
Only qualified personnel (technicians) should install this device. If the equipment is
used in a manner not specified by the manufacturer, the protection provided by the
equipment may be impaired.
WARNING
HAZARD­OUS
VOLTAGE
Until the device is fixed, do not connect hazardous voltages to the device. The
following operations should only be carried out on a disconnected device and under
ESD safe conditions:
General mounting, connection and disconnection of wires.
Troubleshooting the device.
Repair of the device and replacement of circuit breakers must be done by
Omega A/S only.
WARNING
CAUTION
Do not open the front plate of the device as this will cause damage to the connector for the
display / programming front DRSL-DISPLAY.
This device contains no DIP-switches or jumpers.
DRST Series must be mounted on a DIN rail according to DIN EN 60715.
Section 1.2 - Symbol Identification
Triangle with an exclamation mark: Read the manual before installation
and commissioning of the device in order to avoid incidents that could lead
to personal injury or mechanical damage.
The CE mark proves the compliance of the device with the essential
requirements of the directives.
The double insulation symbol shows that the device is protected by double
or reinforced insulation.
5
2
Safety Instructions
Section 2 - Safety instructions
Definitions
Hazardous voltages have been defined as the ranges: 75 to 1500 Volt DC, and 50 to 1000 Volt AC.
Technicians are qualified persons educated or trained to mount, operate, and also trouble-shoot technically correct and in
accordance with safety regulations.
Operators, being familiar with the contents of this manual, adjust and operate the knobs or potentiometers during normal
operation.
Receipt and unpacking
Unpack the device without damaging it and check whether the device type corresponds to the one ordered. The packing should
always follow the device until this has been permanently mounted.
Environment
Avoid direct sun light, dust, high temperatures, mechanical vibrations and shock, and rain and heavy moisture. If necessary,
heating in excess of the stated limits for ambient temperatures should be avoided by way of ventilation.
The device must be installed in pollution degree 2 or better.
Mounting
Only technicians, who are familiar with the technical terms, warnings, and instructions in the manual and who are able to
follow these, should connect the device. Should there be any doubt as to the correct handling of the device, please contact our
Omega tech support.
Mounting and connection of the device should comply with national legislation for mounting of electric materials, i.e. wire cross
section, protective fuse, and location.
Descriptions of input / output and supply connections are shown in the block diagram and side label.
The following apply to fixed hazardous voltages-connected devices:
The max. size of the protective fuse is 10 A and, together with a power switch, it should be easily accessible and close to the
device. The power switch should be marked with a label indicating that it will switch off the voltage
to the device.
Year of manufacture can be taken from the first two digits in the serial number.
UL installation requirements
Use 60/75°C copper conducters only
For use only in pollution degree 2 or better
Max. ambient temperature
Max. wire size
UL file number
60°C
AWG 26-14
E248256
Calibration and Adjustment
During calibration and adjustment, the measuring and connection of external voltages must be carried out according to the
specifications of this manual. The technician must use tools and instruments that are safe to use.
Normal operation
Operators are only allowed to adjust and operate devices that are safely fixed in panels, etc., thus avoiding the danger of
personal injury and damage. This means there is no electrical shock hazard, and the device is easily accessible.
Cleaning
When disconnected, the device may be cleaned with a cloth moistened with distilled water.
Liability
To the extent the instructions in this manual are not strictly observed, the custom­er cannot advance a demand against
Omega A/S that would otherwise exist according to the concluded sales agreement.
6
How to demount DRST Series
Section 3 - How to demount DRST-AC
Picture 1:
The device is detached from the DIN rail by moving the bottom lock down.
When front LED flashes red or DRSL-DISPLAY display shows AO.ER
The DRST-AC is designed with a high safety level. Therefore, the device continuously
measures the output current. If “S4-20” is selected during configuration, and output
current drops to 0 mA, the DRSL-DISPLAY display will indicate “AO.ER” and the
front LED will turn red. (A 0 mA output can be caused by an open output loop). The
error mode can be reset by power cycling the device or stepping through the menu.
7
3
4
Universal AC/DC transmitter
Section 4.1 - Universal AC/DC transmitter
•Measures AC current and voltage signals and converts these into uni-/bipolar DC current and voltage signals ~
• Outputs passive or active current signals
•Programming, process monitoring and diagnostics via DRSL-DISPLAY
• Response time < 0.75 s and excellent accuracy better than 0.3%
• Universally powered by 21.6…253 Vac / 19.2...300 Vdc
Application
• The 0... 5 AAC range makes it possible to accurately measure a typical current transformer.
• The 0...300 VAC range allows accurate supply voltage monitoring.
•The DRST-AC measures standard input ranges, and can be freely configured to customer-defined input range.
•Converts narrow AC current / voltage inputs to wide bipolar or unipolar outputs, e.g. 0…1 VAC input = ±10 volt or 4...20 mA
output with a minimum span of 0.5 AAC or 0.5 VAC.
• The detachable DRSL-DISPLAY displays provide enhanced diagnostics.
• Configurable input limits control the output value for increased safety.
Technical characteristics
•The latest analog and digital techniques are used to obtain maximum accuracy and immunity to interference.
• Possibility of output safety readback by selecting S4...20 mA output.
• Response time < 0.75 s for measuring AC current / voltage signals.
• The current output can drive up to 800 Ohms, with an adjustable response time of 0.0…60.0 seconds.
• Exceptional mA output load stability of < 0.001% of span / 100 Ohm.
• Meets the NAMUR NE21 recommendations, ensuring high accuracy in harsh EMC environments.
• Meets the NAMUR NE43 recommendations, allowing the control system to easily detect an input error.
• Each unit is tested to a high 2.3 kVAC, 3-port galvanic isolation level.
• Excellent signal to noise ratio of > 60 dB.
Mounting / installation / programming
•Very low power consumption means units can be mounted side by side without an air gap – even at 60°C ambient temperature.
•Configuration, monitoring, 2-point process calibration and more are accomplished using either the DRSL-DISPLAY detachable
display or the DRST-CM detachable digital communication enabler.
• All programming can be password-protected.
8
Signals/Connection
5
Section 5.1 - signals:
Current
Voltage
44
43
(N)
42
(N)
41
Section 5.2 - Output signals:
+ V supply
Current & voltage
12
+
14
+
10 V
1V
13
+
11
Section 5.3 - Power connection:
21.6...253 VAC
or
19.2...300 VDC
33
32
31
9
10 V
1V
+
}
2-wire
(±)
6
DRSL-DISPLAY display / programming front
Section 4.1 - Universal AC/DC transmitter
Functionality
The simple and easily understandable menu structure and the explanatory help texts guide you
effortlessly and automatically through the configuration steps, thus making the product very easy to
use. Functions and configuration options are described in the section ”Configuration / operating the
function keys”.
Application
• Communications interface for modification of operational parameters in DRST-AC.
•Can be moved from one DRST-AC device to another and download the configuration of the first unit
to subsequent units.
• When mounted in the process, the display shows process values and device status.
Technical characteristics
• LCD display with 4 lines:
Line 1 (H=5.57 mm) shows the scaled process value - OK or error.
Line 2 (H=3.33 mm) shows the selected engineering unit.
Line 3 (H=3.33 mm) shows analog output or TAG no.
Line 4 shows status for communication and signal trending.
•Programming access can be blocked by assigning a password. The password is saved in the device in
order to ensure a high degree of protection against unauthorized modifications to the configuration.
Mounting/demounting the DRSL-DISPLAY/DRST-CM
1: Insert the tabs of the DRSL-DISPLAY/DRST-CM into the holes at the top of the device.
2: Hinge the DRSL-DISPLAY/DRST-CM down until it snaps into place.
Demounting of the DRSL-DISPLAY/DRST-CM
3: Push the release button on the bottom of the DRSL-DISPLAY/DRST-CM and hinge the the
DRSL-DISPLAY/DRST-CM out and up.
4: With the DRSL-DISPLAY/DRST-CM hinged up, remove from holes at the top of the device.
1
44
ÂÂ
OK
3
4501
ÂÂÂ
ÂÂ 2
3
10
Order
Section 7 - Order
DRST-AC = Universal AC/DC transmitter
Accessories
DRSL-DISPLAY = Display/programming front
DRST-CM = Communication enabler
Electrical specifications
Environmental conditions:
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20 to 60°C
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -20 to 85°C
Calibration temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20...28°C
Relative humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . < 95% RH (non-cond.)
Protection degree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP20
Installation in pollution degree 2 & measurement / overvoltage category II.
Mechanical specifications:
Dimensions (H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions (H x W x D) w/DRSL-DISPLAY/DRST-CM . . . . . . . . . . .
Weight approx. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Weight incl. DRSL-DISPLAY/DRST-CM (approx.) . . . . . . . . . . . . . .
DIN rail type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109 x 23.5 x 104 mm
109 x 23.5 x 116 / 131 mm
250 g
285 g / 350 g
DIN EN 60715 - 35 mm
0.13...2.08 mm2 /
AWG 26...14 stranded wire
Screw terminal torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 Nm
Common electrical specifications:
Supply voltage, universal . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.6...253 VAC, 50...60 Hz
or 19.2...300 Vdc
Max. required power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 1.8 W nom.
Max. power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 2.5 W
Isolation voltage - test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 kVac
Isolation voltage - working . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 Vac (reinforced) / 500 Vac (basic)
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Communication enabler DRST-CM/
Programming front DRSL-DISPLAY
Signal dynamics, input / output . . . . . . . . . . . . . . . . . . . . . . . . 20 bit / 18 bit
Signal/noise ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 60 dB
Response time (0...90%, 100...10%) . . . . . . . . . . . . . . . . . . . . . . . < 0.75 s
Output referred common mode rejection ratio . . . . . . . . . . . . . . . . . 0.02 ppm / VHz
11
7
7
Order
Accuracy, the greater of general and basic values:
General values
Input type
Absolute accuracy
Temperature coefficient
All
≤ ±0.3% of span*
≤ ±0.01% of span* / °C
Basic values
Input type
Basic accuracy
Temperature coefficient
Current
1.5 mA
50 µA/ °C
Voltage
1.5 mVAC
50 µVAC /°C
EMC - immunity influence . . . . . . . . . . . . . . . . . . . . . . < ±0.5% of span*
Extended EMC immunity:
NAMUR NE 21, A criterion, burst . . . . . . . . . . . . . . . . . . < ±1% of span*
of span = of selected standard range
* For custom signals, general accuracy and EMC specifications are 0.3% of full scale
Input specifications:
Current input:
Signal range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum input limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programmable measurement ranges . . . . . . . . . . . . . . . . . . . . . .
Custom configurable signal range . . . . . . . . . . . . . . . . . . . . . . . .
Min. span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0...5 AAC / 40...400 Hz
6.00 AAC @ 40°C
0...0.5, 0…1, 0…2.5 & 0...5 AAC
0….5 AAC / 40...400 Hz
0.5 AAC
Nom. < 0.07 Ω
Voltage input:
Signal range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0...300 VAC / 40...400 Hz
Programmable measurement ranges . . . . . . . . . . . . . . . . . . . . . . 0...0.5, 0...1, 0...2.83, 0…5, 0…120, 0…230 &
0…300 VAC
Custom configurable signal range . . . . . . . . . . . . . . . . . . . . . . . . 0...300 VAC / 40...400 Hz
Min. span . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 VAC
Input resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Nom. 3 MΩ || 100 pF
Configurable input limits:
Configurable input limits, low:
VOLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 VAC to ‘Minimum selected input’
CURR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 AAC to ‘Minimum selected input’
Configurable input limits, high:
VOLT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‘Maximum selected input’ to 300 VAC
CURR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ‘Maximum selected input’ to 5 AAC
12
Order
Input limit low/high, error indication levels:
UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DOWN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ZERO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NONE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hysteresis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error detection release delay . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
See table on page 15
See table on page 15
See table on page 15
See table on page 15
0.5% of ‘Max. output’
< 2.5 s
Current output specifications:
Active unipolar and bipolar mA:
Programmable ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0...20, 4...20, S4...20, ±10 and ±20 mA
Direct or Inverted action
V-curve function, 100-0-100% . . . . . . . . . . . . . . . . . . . . . . . . . . 20-0-20 mA
Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 800 Ω
Passive 2-wire mA:
Programmable ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0...20 and 4...20 mA
Direct or Inverted action
V-curve function, 100-0-100% . . . . . . . . . . . . . . . . . . . . . . . . . . 20-0-20 mA
External 2-wire loop supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5...30 V
Common specifications current output:
All standard and custom ranges can be selected as Direct or Inverted action.
V-function can be selected for fixed output ranges starting at zero.
Signal range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0...23 mA (unipolar) /
-23...+23 mA (bipolar)
Current limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 28 mA (unipolar) /
±28 mA (bipolar)
Load stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ≤ 0.001% of span / 100 Ω
Response time, programmable . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0...60.0 s
Output limitation at outside range . . . . . . . . . . . . . . . . . . . . . . . See table on page 14
Voltage output specifications:
All standard and custom ranges can be selected as Direct or Inverted action.
V-function can be selected for fixed output ranges starting at zero.
Programmable ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0/0.2...1, 0/1...5, 0/2...10, ±1, ±5 and ±10 V
Direct or Inverted action
V-curve function, 100-0-100% . . . . . . . . . . . . . . . . . . . . . . . . . . 1-0-1 V, 5-0-5 V and 10-0-10 V
Load, min . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 500 kΩ
Response time, programmable . . . . . . . . . . . . . . . . . . . . . . . . . . 0.0...60.0 s
Output limitation at outside range . . . . . . . . . . . . . . . . . . . . . . . See table on page 14
Observed authority requirements:
EMC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2014/30/EU
LVD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2014/35/EU
RoHS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2011/65/EU
Approvals:
c UL us, Standard for Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . UL 508 / C22.2 No. 14
13
8
Configurable input error indication and input limits
Section 8 - Configurable input error indication and input limits
Configurable input error detection
To increase system safety and integrity, users can program a high and low input error detection level. Input signals outside
the selected error indication levels will cause the output of the device to go to the programmed error state. The error is
indicated in display line 1 as IN.ER and at the same time the backlight flashes.
The two configurable input error detection levels can be set and enabled individually, just as it is possible to individually set
the output error indication for each of the two detection levels. This allows users to differentiate process faults, broken input
wires, etc.
Available output error states for each of the two detection levels are: UP, DOWN, ZERO and NONE.
Output error indication uses the error states defined by NAMUR NE43 for 4...20 mA output span, and for all other output
spans equivalent output error indications are used (see table on page 14).
Example - 4..20 mA output span and both high and low configurable input error limit enabled with output error
indication set to ZERO:
Device
Min. input
Configurable input
limit, low
Normal measuring range
Configurable input
limit, high
Device
Max. input
Extended measuring range
20.0 mA
Normal range
Extended working range
20.5 mA
4.0 mA
3.8 mA
Error current
Error current
Output error indication = ZERO
Output error current can be
individually set to:
ZERO:
0 mA
UP:
23 mA
DOWN:
3.5 mA
DISABLED: No error indication,
output limited to 3.8 mA
Input:
ARMS,
VRMS
etc.
Output error current can be
individually set to:
ZERO:
0 mA
UP:
23 mA
DOWN:
3.5 mA
DISABLED: No error indication,
output limited to 20.5 mA
Example - input limits disabled:
‘Min. selected
input’ - 15%
‘Max. selected
input’ + 15%
Normal measuring range
Extended measuring range
Normal range
Extended working range
20.5 mA
20.0 mA
4.0 mA
3.8 mA
Output error indication = NONE
14
Input:
ARMS,
VRMS
etc.
Configurable input error indication and input limits
Input limit check
disabled
8
Input limit check Low and / or High enabled
Output
error
indication,
NONE
Output
limit low
Output
limit high
Output
limit low
Output
limit high
Output
error
indication,
UP
Output
error
indication,
DOWN
Output
error
indication,
ZERO
4...20 mA
0 mA
23 mA
3.8 mA
20.5 mA
23 mA
3.5 mA
0 mA
No error
indication
0...20 mA
0 mA
23 mA
0 mA
20.5 mA
23 mA
0 mA
0 mA
No error
indication
±10 mA
-11.5 mA
11.5 mA
-10.25 mA
10.25 mA
11.5 mA
-11.5 mA
0 mA
No error
indication
±20 mA
-23 mA
23 mA
-20.5 mA
20.5 mA
23 mA
-23 mA
0 mA
No error
indication
Output
span
Input limit check
disabled
Input limit check Low and / or High enabled
Output
error
indication,
NONE
Output
limit low
Output
limit high
Output
limit low
Output
limit high
Output
error
indication,
UP
Output
error
indication,
DOWN
Output
error
indication,
ZERO
0...1 V
0V
1.15 V
0V
1.025 V
1.15 V
0V
0V
No error
indication
0.2...1 V
0V
1.15 V
0.195 V
1.025 V
1.15 V
0.175 V
0V
No error
indication
0...5 V
0V
5.75 V
0V
5.125 V
5.75 V
0V
0V
No error
indication
1...5 V
0V
5.75 V
0.975 V
5.125 V
5.75 V
0.875 V
0V
No error
indication
0...10 V
0V
11.5 V
0V
10.25 V
11.5 V
0V
0V
No error
indication
2...10 V
0V
11.5 V
1.95 V
10.25 V
11.5 V
1.75 V
0V
No error
indication
±1 V
-1.15 V
1.15 V
-1.025 V
1.025 V
1.15 V
-1.15 V
0V
No error
indication
±5 V
-5.75 V
5.75 V
-5.125 V
5.125 V
5.75 V
-5.75 V
0V
No error
indication
±10 V
-11.5 V
11.5 V
-10.25 V
10.25 V
11.5 V
-11.5 V
0V
No error
indication
Output
span
15
9
DRSL-DISPLAY/DRST-CM display readout
Section 9.1 DRSL-DISPLAY/DRST-CM display readout
Display readout of input error detection and signal ”outside range”
Configurable input error detection - readout (IN.ER):
Input
Range
Readout
Limit
CURR
All
IN.ER
See table on page 14
VOLT
All
IN.ER
See table on page 14
Display readout below min. / above max. (-1999, 9999):
Input
Range
All
All
Readout
Limit
-1999
Display readout <-1999
9999
Display readout >9999
Readout at hardware error
Error search
Readout
Cause
Check measurement of analog output
AO.ER
No load on the current output (only S4...20 mA)*
Communications test between
DRSL-DISPLAY/DRST-CM and DRST-AC
NO.CO
Connection error
Configuration error
CO.ER
Default configuration is loaded
Configuration error
CO.ER
Invalid configuration**
Check that saved configuration in
DRSL-DISPLAY/DRST-CM matches device
TY.ER
Invalid type or rev. no.
Hardware error
RA.ER
RAM error*
Hardware error
AD.ER
A/D converter error*
Hardware error
AO.SU
Analog output supply error*
Hardware error
EF.ER
External flash error*
Hardware error
IF.ER
Internal flash error*
!
*
**
All error indications in the display flash once per second. The help text explains the error. If the error is an
input loop error, the display backlight flashes as well - this is acknowledged (stopped) by pushing the 3
button.
Error is acknowledged by either stepping through the basic setup, or by resetting the device power.
Some types of errors can only be acknowledged by resetting the device power.
Error is acknowledged by stepping through the basic setup.
16
Connections
Section10.1 - Connections
Supply
31
32
33
Inputs:
Current
Voltage
41 42 43 44
41 42 43 44
Outputs:
Current
2-wire transmitter
Voltage, 1 V
Voltage, 10 V
11 12 13 14
11 12 13 14
11 12 13 14
11 12 13 14
- mA +
(±)
mA
-
-
+
V
(±)
17
+
-
V
(±)
+
10
11
Block Diagram
Section11.1 - Block Diagram
33
44
32
Red
31
HW
Watchdog
Supply
21.6...253 VAC or
19.2...300 VDC
N.C.
Supply
43
12
D /A
(N) 42
A/D
CPU
Current
input

  
 
I+
Green
A
500
41
50
Voltage
input
14
10 V
13
1V
11
I- / V-
A
V
DRST-AC
4179
18
I+V
+
-
V
V
A
I
I
Configuration / Operating the function keys
12
Section 12.1 - Configuration / operating the function keys
Documentation for routing diagram.
In general
When configuring the DRST-AC, you will be guided through all parameters and you can choose the settings
which fit the application. For each menu there is a scrolling help text which is automatically shown in line 3 on
the display.
Configuration is carried out by use of the 3 function keys:
1
will increase the numerical value or choose the next parameter
3
will save the chosen value and proceed to the next menu
2
will decrease the numerical value or choose the previous parameter
When configuration is completed, the display will return to the default state 1.0. Pressing and holding 3 will
return to the previous menu or return to the default state (1.0) without saving the changed values or parameters.
If no key is activated for 1 minute, the display will return to the default state (1.0) without saving the changed
values or parameters.
Further explanations
Password protection: Programming access can be blocked by assigning a password. The password is saved in
the device in order to ensure a high degree of protection against unauthorised modifications to the
configuration. Default password 2008 allows access to all configuration menus.
Signal and sensor error indication via display front DRSL-DISPLAY/DRST-CM
Error indication is displayed in line 1 as text and at the same time the backlight flashes. A flashing bullet in line
4 is indicating correct functioning of DRST-DISPLAY.
Signal and sensor error indication without display front
Status of the unit can also be read from the red/green LED in the front of the device.
Green flashing LED 13 Hz indicates normal operation.
Green flashing LED 1 Hz indicates loop error.
Steady green LED indicates internal error.
Steady red LED indicates fatal error.
Advanced functions
The unit gives access to a number of advanced functions which can be reached by answering “Yes” to the point
“ADV.SET”.
Memory (MEM): In the memory menu you can save the configuration of the device in the DRST-DISPLAY, and
then move the DRST-DISPLAY onto another device of the same type and download the configuration in the
new device.
Display setup (DISP): Here you can adjust the brightness contrast and the backlight. Setup of TAG numbers with
6 alphanumerics. Selection of functional readout in line 3 of the display - choose between readout of analogue
19
12
Configuration / Operating the function keys
Section 12.1 - Configuration / Operating the function keys
output or tag no.
Two-point process calibration (CAL): The device can be process-calibrated in 2 points to fit a given input signal . A low input
signal (not necessarily 0%) is applied and the actual value is entered via DRSL-DISPLAY/DRST-CM Then a high signal (not
necessarily 100%) is applied and the actual value is entered via DRSL-DISPLAY/DRST-CM. If you accept to use the calibration,
the device will work according to this new adjustment. If you later reject this menu point or choose another type of input signal
the device will return to factory calibration.
Process simulation function (SIM): In the menu point “EN.SIM” it is possible to simulate an input signal by means of the arrow
keys and thus control the output signal up or down. You must exit the menu by pressing 3 (no time-out).
The simulation function exits automatically, if the DRSL-DISPLAY/DRST-CM is detached.
Password (PASS): Here you can choose a password between 0000 and 9999 in order to protect the unit against unauthorised
modifications to the configuration. The unit is delivered default without password.
Language (LANG): In the menu ”LANG” you can choose between 7 different language versions of help texts that will appear in
the menu. You can choose between UK, DE, FR, IT, ES, SE and DK.
Output function (OFUN): Here the output characteristics can be set to either Direct (DIR) or Inverted (INV) function. Output
type and range are set in the normal programming menu. If the selected output range is starting at zero, V-curved output
function (VFUN) can also be selected. The output characteristics will then be 100-0-100% on the basis of a linear 0-100% input
signal.
Auto diagnostics
The device performs an advanced auto diagnosis of the internal circuits - check tables on page 15.
20
Routing Diagram
Section 13.1 - Routing diagram
If no key is activated for 1 minute, the display will return to the default state 1.0 without saving
configuration changes.
1 Increase value / choose next parameter
2 Decrease value / choose previous parameter
3 Save the chosen value and proceed to the next menu
Hold 3 Back to previous menu / return to menu 1.0 without saving.
Power up
40.0
%
10.4 mA
0000
9999
OK
*0
0000
NO
YES
Correct
OK
PASSW.
Txt 1
*1
0-5
0-2.5
0-1
0-0.5
CURR
VOLT
No
NO
OK
ADV.SET
Txt 2
VOLT
CURR
OK
IN TYPE
Txt 3
Yes
0-5
OK
Txt 4
0-300
0-230
0-120
0-5
0-2.83
0-1
0-0.5
CUST
VOLT
OK
0-230
OK
V.RANGE
Txt 5
NO
YES
YES
ADV.SET
Txt 2
Default state.
Line 1 shows the scaled process value - OK or
error.
Line 2 shows the selected engineering unit.
Line 3 shows analogue output or TAG no.
Line 4 shows status for communication and
signal trending.
*0
*1
Only displayed if password is enabled.
OK
Continued on the page
Routing diagram ADV.SET
*7
Only displayed if CUST is selected!
This menu will change range automatically.
*8
Value will be forced to be greater than
xx.LO.
*9
Maximum and minimum value selectable
from menu must be based on input type
VOLT:
Min: 0.000
Max: 300
CURR:
Min: 0.000
Max: 5.00
21
0.00
IN.LO
Txt 48
*7
*9
I.RANGE
and held:
Toggle line 3 function
A.Out / TAG.
(Setting is volatile use DISP setup menu
to change and store
line 3 function).
300
0.00
300
0.00
CUST
OK
230
OK
IN.HI
Txt 49
*7
*8
*9
13
13
Routing Diagram
blank
:
:
111.1
%
11.11
@F
1.111
@C
1111
UNIT
A RMS
Txt 6
9999 9999
-9999 -9999
1.111
5.000
0.00
DEC.P DISP.LO DISP.HI
Txt 7
Txt 8
Txt 9
-/+20
-/+10
S4-20
4-20
0-20
CURR
VOLT
OK
CURR
CURR
4-20
OK
ANA.OUT
-/+10
-/+5
-/+1
2-10
0-10
VOLT
OK
0-10
Txt 12
*3
in
in/h
in/min
in/s
ips
K
kA
kg
kJ
kPa
kV
kW
kWh
l
l/h
l/min
l/s
m
m/h
m/min
m/s
m/s2
m3
m3/h
m3/min
mA
mbar
mils
min
mm
mm/s
mol
Mpa
mV
MW
MWh
N
Ohm
Pa
pH
rpm
s
S
t
t/h
uA
um
uS
V
W
Wh
yd
VRMS
ARMS
[blank]
22
ACTI
OUT.MOD
Txt 13
*2
1-5
0-5
0.2-1
0-1
O.RANGE
°C
°F
%
A
bar
cm
ft
ft/h
ft/min
ft/s
g
gal/h
gal/min
GW
hp
hPa
Hz
OK
O.RANGE
Txt 11
*3
Txt 10
Selectable UNITS:
PASS
ACTI
OK
OK
Routing Diagram
YES
NO
NO
0.00
0.00
0.00
OK
ILIM.L
Txt 50
NO
*15
VRMS
Txt 51
UP
ZERO
DOWN
NONE
UP
OUT.ERR
Txt 54
YES
NO
OK
300
230
YES
230
OK
ILIM.H
Txt 52
NO
23
*16
VRMS
Txt 53
UP
ZERO
DOWN
NONE
UP
OUT.ERR
Txt 54
13
60.0
0.0
OK
0.0
RESP.
Txt 15
OK
To default state
1.0
13
Routing Diagram
Section 13.2 - advanced settings (ADV.SET)
MEM, DISP,
CAL, SIM,
PASS, LANG,
OFUN
MEM
*6
SAVE
LOAD
OK
SETUP
Txt 15/1
SAVE
*5
OK
SETUP
Txt 15/2
CAL
OK
OK
3
9
OK
TAGNO_
Txt 19
YES
NO
5.000
0.000
YES
NO
NO
OK
0.000
*5
NO
OK
ENA.SIM
Txt 26
YES
NO
OK
SETUP
Txt 15/5
NO
EN.PASS
Txt 28
NO
OK
SETUP
Txt 15/6
UK
SETUP
Txt 15/7
DIR
O.FUNC
Txt 31
OK
5.000
*5
A RMS
Txt 24
YES
NO
OK
NO
2.500
*5
OK
A RMS
Txt 27
In the submenu simulation (SIM) you must press 3 or remove
the DRSL-DISPLAY/DRST-CM to return to the default state 1.0.
9999
0
OK
NO
0
OK
USE.CAL
Txt 25
To default state
1.0
OK
NEW.PAS
Txt 29
OK
LANGUA.
Txt 30
OK
5.000
0.000
NO
VFUN
INV
DIR
OFUN
OK
LINE 3
Txt 20
CAL.HI
Txt 23
DE, DK, ES, FR,
IT, SE, UK
LANG
A.OUT
5.000
0.000
NO
PASS
OK
A RMS
Txt 22
TAG
A.OUT
OK
LIGHT
Txt 18
YES
NO
OK
OK
CONTRA
Txt 17
NO
SETUP
Txt 15/4
9
A
9
0
CAL.LO
Txt 21
SETUP
Txt 15/3
SIM
VFUN (V-shaped output function) is only available when a
fixed output range starting at zero is seleceted.
DIR (direct) and INV (inverted) output can be combined with
all fixed or CUST output ranges.
MEMORY
Txt 16
9
0
DISP
Selectable range as defined by DEC.P, DISP.LO and DISP.HI.
OK
24
Routing Diagram
13
Section 13.3 - Help text overview
[1]
Set correct password
[2]
Enter advanced setup menu?
[3]
Select current input
[14]
Select voltage input
[15] Select Analog Output Function
[4]
[5]
[13] Select active output mode
Select passive output mode
Set Analog output response time in seconds
Select 0...5 A input range
Enter Language setup
Select 0...2.5 A input range
Enter Password setup
Select 0...1 A input range
Enter Simulation mode
Select 0...0.5 A input range
Perform Process calibration
Select custom current input range
Enter Display setup
Select 0...230 V input range
Perform Memory operations
Select 0...120 V input range
[16] Load saved configuration into module
Select 0...2.83 V input range
Save configuration in display front
Select 0...1 V input range
[17] Adjust LCD contrast
Select 0...0.5 V input range
[18] Adjust LCD backlight
Select custom voltage input range
[19] Write a 6-character device TAG
[6]
Select display unit
[20] Analog output value is shown in display line 3
[7]
Select decimal point position
[8]
Set display range low
[21] Calibrate Input low to process value?
[9]
Set display range high
[22] Set value for low calibration point
Device TAG is shown in display line 3
[10] Select current as analog output type
[23] Calibrate Input high to process value?
Select voltage as analog output type
[24]
[11] Select 0...20 mA output range
Set value for high calibration point
[25] Use process calibration values?
Select 4...20 mA output range
[26] Enable simulation mode?
Select 4...20 mA with safety readback
Select -10...10 mA output range
Select -20...20 mA output range
[12] Select 0.0...1 V output range
Select 0.2...1 V output range
Select 0...5V output range
Select 1...5V output range
Select 0...10V output range
Select 2...10V output range
Select -1...1 V output range
Select -5...5 V output range
Select -10..10 V output range
25
13
Help text overview
[27]
Set the input simulation value
[28]
Enable password protection?
[29]
Set new password
[30]
Select language
[31]
Select direct output mode
Select inverted output mode
Select V-function output mode
[32]
Display underrange
[33]
Display overrange
[34]
Input underrange
[35]
Input overrange
[36]
Analog output supply error
[37]
Analog output error - check output connections and reset power
Configuration error - default configuration is loaded
[38]
RAM memory error
[39]
Invalid configuration
[40]
A/D converter error
[41]
No communication
[42]
Input range limit error - Input outside configurable input range limit
[44]
Invalid configuration type or version
External flash error
[45]
Internal flash error
[46]
Set input range low
[47]
Set input range high
[48]
Enable configurable input limit, low
[49]
Set configurable input limit, low
[50]
Enable configurable input limit, high
[51]
Set configurable input limit, high
[52]
Select downscale at error
[53]
Select zero output at error
[54]
Select upscale at error
Select no error action - output undefined at error
Section 13.4 - Document history
The following list provides notes concerning revisions of this document.
Rev. ID
100
Date
Notes
1740
Initial release of the product
26
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a
period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace
period to the normal one (1) year product warranty to cover handling and shipping time. This ensures
that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service
Department will issue an Authorized Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;
or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for
any damages that result from the use of its products in accordance with information provided
by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any
correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent
breakage in transit.
FOR NON-WARRANTY REPAIRS, consult
FOR WARRANTY RETURNS, please have the
OMEGA for current repair charges. Have
following information available BEFORE contacting
the following information available BEFORE
OMEGA:
contacting OMEGA:
1.Purchase Order number under which the product
1. Purchase Order number to cover the COST
was PURCHASED,
of the repair,
2.Model and serial number of the product under
2. Model and serial number of the product, and
warranty, and
3. Repair instructions and/or specific problems
3. Repair instructions and/or specific problems
relative to the product.
relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our
customers the latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior
written consent of OMEGA ENGINEERING, INC.
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
TEMPERATURE
M
U Thermocouple, RTD & Thermistor Probes, Connectors,
Panels & Assemblies
M
U Wire: Thermocouple, RTD & Thermistor
M
U Calibrators & Ice Point References
M
U Recorders, Controllers & Process Monitors
M
U Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
M
U Transducers & Strain Gages
M
U Load Cells & Pressure Gages
M
U Displacement Transducers
M
U Instrumentation & Accessories
FLOW/LEVEL
M
U Rotameters, Gas Mass Flowmeters & Flow Computers
M
U Air Velocity Indicators
M
U Turbine/Paddlewheel Systems
M
U Totalizers & Batch Controllers
pH/CONDUCTIVITY
M
U pH Electrodes, Testers & Accessories
M
U Benchtop/Laboratory Meters
M
U Controllers, Calibrators, Simulators & Pumps
M
U Industrial pH & Conductivity Equipment
DATA ACQUISITION
M
U Communications-Based Acquisition Systems
M
U Data Logging Systems
M
U Wireless Sensors, Transmitters, & Receivers
M
U Signal Conditioners
M
U Data Acquisition Software
HEATERS
M
U Heating Cable
M
U Cartridge & Strip Heaters
M
U Immersion & Band Heaters
M
U Flexible Heaters
M
U Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
M
U Metering & Control Instrumentation
M
U Refractometers
M
U Pumps & Tubing
M
U Air, Soil & Water Monitors
M
U Industrial Water & Wastewater Treatment
M
U pH, Conductivity & Dissolved Oxygen Instruments
M5691/1018
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising