Omega | HHC280 | Owner Manual | Omega HHC280 Owner Manual

Omega HHC280 Owner Manual
SPECIFICATIONS
HHC280
Differential Manometer
INSTRUCTION
SHEET
M5515/0418
Shop online at omega.com e-mail: info@omega.com
For latest product manuals: omegamanual.info
APO
HOLD MAX MIN AVG
mmH 2O mmHg psi inH O2inHg
hPa mbar Pa
Density (kg/m ) 3(ib/ft ) 3
ENTER
HHC280
DIFFERENTIAL MANOMETER
INTRODUCTION
This instrument is design to measure the difference between the pressures applied on the two ports
of the meter. With a Pitot tube (separate purchasing)
the meter also measures air speed.
Besides displaying result of current measurement,
and hold function the meter also store max / min /
max-min / avg values.
SAFETY INFORMATION
Only operate the measuring instrument properly,
for its intended purpose and within the units specified in the technical data. Do not use force.
Never store the product together with solvents,
acids or other aggressive substances.
Only carry out the maintenance and repair work
that is described in the documentation. Follow the
prescribed steps when doing so.
Unit
mmH2O
mmHg
psi
inH2O
inHg
hPa
mbar
Pa
fpm
m/s
Range
0 to 1019.7
0 to 75.00
0 to 1.450
0 to 40.14
0 to 2.953
0 to 100.00
0 to 100.00
0 to 10000
*
*
Resolution
0.1
0.01
0.001
0.01
0.001
0.01
0.01
1
1
0.1
Accuracy: Nominal temperature 22°C, ±1dgt)
±0.03 hPa(0 to 0.30 hPa),
±0.05 hPa(0.31 to 1.00 hPa),
±(0.1 hPa+1.5% of reading) (rest of range)
±0.3 mmH2O(0 to 3.0 mmH2O),
±0.5 mmH2O(3.1 to 10.2 mmH2O),
±(1.02 mmH2O + 1.5% of reading) (rest of range)
Measurement rate: 2 times/second.
Auto power off: 10 minutes.
” is displayed
Low battery indication: The “
when the battery voltage drops below the operating level.
Operating Environment: 0°C to 50°C (32°F to
122°F) at < 70% R.H.
Storage Temperature: -20°C to 60°C (-4°F to
140°F), 0 to 80% R.H. with battery removed from
meter.
Battery: 1.5Vx2pcs AAA size.
Battery Life: 85 hours typical.
Dimensions: 24.7mm(T) x 50.9mm(W) x 132.9
mm(H).
Weight: Approx. 113g. (Including batteries)
OPERATIONS
There are 3 operation modes, namely Measurement Mode, Set Mode and Hold Mode.
1. Turning on and off the meter:
When power is off, a short push on “ ” key turns
on the meter and enter Measurement Mode.
When power is on press and hold “ ” key for 2
seconds turns the power off.
Right after power on, all the indicators on the
LCD display lights up for one second.
2. Measurement Mode:
Before start measuring, disconnect the meter from
pressure sources, press “▲” key to zero the meter.
(When there is a measurement > 10hpa, Zeroing
function is disabled).
Connect the meter to the pressure sources, the
meter start measuring and refresh every 0.5 seconds.
Backlight:
In measurement mode, a short push on “ ” key
turns on the backlight for dark environment, it
goes off automatically after 15 seconds if without
further operation.
3. Set Mode:
In set mode, user can select Unit , Density of Medium and turn on/off APO function.(APO = Auto
Power Off, when APO is ON, the meter power off
automatically if no operation in 10 minutes.)
When power is off, press and hold “ ” key for 2
seconds to enter Set Mode.
3.1 Unit setting: Press “▲” key to change unit
(press and hold “▲” key, to scroll units),
press “MODE” to selection the unit and enter
next setting. If unit of air speed (fpm or m/s)
is selected, then next setting is density setting
otherwise APO setting.
3.2 Density of the medium setting: Press “▲” key
to change value (press and hold “▲” key to
scroll values), press “MODE” key to select
and enter APO On/Off setting (Max. Density:
0.624lb/ft3 or 9.999kg/m3)
3.3 APO ON/OFF: short push on “▲” key
switches
between ON and OFF. Push “MODE” key to
select, exit Set Mode and Enter Measurement
Mode.
(Please refer to the section of Measurement
Mode.)
※Note: To turn off power in Set Mode abandon the
current setting and previous settings remain unchanged. If “
” indicator appeared, the setting
value can works till power off but did not save to
meter.
4. Hold Mode:
In Measurement Mode, short push “Mode” key to
enter Hold Mode with indicator “HOLD” shows
at upper left corner of LCD.
Right after entering this mode, shown in the LCD
is the last measurement and the reading will not
be updated with new measurement.
Push “Mode” key each time the display changes
in following sequence:
4.1 Last Measurement: with indicator “HOLD”.
4.2 Maximum value recorded: with indicator
“HOLD” + “MAX”.
4.3 Minimum value recorded: with indicator
“HOLD” + “MIN”.
4.4 Maximum-Minimum value recorded: with indicator “HOLD” + “MAX-MIN”.
4.5 Average of values recorded: with indicator
“HOLD” + “AVG”. (only for wind speed)
4.6 Exit the Hold Mode and return to Measurement Mode.
To clear the recorded values:
In Hold Mode and during viewing MAX, MIN,
MAX-MIN or AVG, press and hold “Mode” key
for 2 seconds, to clear the recorded data and return to measurement mode.
Installing and Replacing Battery
A. Battery Cover
B. Battery
1. Power is supplied by 2pcs 1.5V (AAA SIZE).
” appears in the display when battery
2. The “
replacement is needed.
3. Push the Battery Cover and lift it in the direction
as shown in the figure.
4. Remove the batteries from battery compartment.
5. Replace with 2 new AAA batteries with polarity
as indicated on the bottom of Battery Compartment.
6. Replace the Battery Cover.
※Note: When not use for long time remove battery
and don’t keep in place with high Temp, or
high humidity.
Cleaning
Periodically wipe the case with a damp cloth and
detergent, do not use abrasives or solvents.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a
period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month
grace period to the normal one (1) year product warranty to cover handling and shipping time. This
ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service
Department will issue an Authorized Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;
or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for
any damages that result from the use of its products in accordance with information provided
by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department.
BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED
RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return
package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent
breakage in transit.
FOR WARRANTY RETURNS, please have the
following information available BEFORE
contacting OMEGA:
1. Purchase Order number under which the product
was PURCHASED,
2. Model and serial number of the product under
warranty, and
3. Repair instructions and/or specific problems
relative to the product.
FOR NON-WARRANTY REPAIRS, consult OMEGA
for current repair charges. Have the following
information available BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST
of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems
relative to the product.
omega.com info@omega.com
Servicing North America:
U.S.A.
Headquarters:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com
TEMPERATURE
Thermocouple, RTD & Thermistor Probes,
Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
pH/CONDUCTIVITY
pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
Communications-Based Acquisition Systems
Data Logging Systems
Wireless Sensors, Transmitters, & Receivers
Signal Conditioners
Data Acquisition Software
HEATERS
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the
prior written consent of OMEGA ENGINEERING, INC.
M5515/0418
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising