Omega | iLD46-C2 | Owner Manual | Omega iLD46-C2 Owner Manual

Omega iLD46-C2 Owner Manual
SPECIFICATION
d
bc
ALR1
OFF
A1Md
A1LO
A1LH
LO-1
d
bc
d
bc
bc
d
bc
d
bc
bc
bc
d
d
bc
d
bc
bc
d
bc
d
bc
d
a
d
bc
d
bc
bc
bc
bc
d
d
d
a
a
d
bc
d
a
d
bc
d
a
d
bc
d
bc
bc
d
d
1
1
1
1
1
1
Status
set Off
Mode
Low
Low/High
Low
ON
Alarm 1 set On
A1HI
Alarm 1 High
-999.. Alarm 1 Low Value
..9999
HI-1
Alarm 1 High
-999.. Alarm 1 High Value
..9999
A1CR Display color when Alarm 1 triggered
GRN
Green Color
REd
Red Color
AMbR Amber Color
ALR2 Alarm 2 Status
OFF
Alarm 2 set Off
ON
Alarm 2 set On
A2Md Alarm 2 Mode
A2LO Alarm 2 Low
A2HI
Alarm 2 High
A2LH Alarm 2 Low/High
LO-2
Alarm 2 Low
-999.. Alarm 2 Low Value
..9999
HI-2
Alarm 2 High
-999.. Alarm 2 High Value
..9999
A2CR Display color when Alarm 2 triggered
GRN
Green Color
REd
Red Color
AMbR Amber Color
OUt
Alarm Latched/Unlatched selection
LAtC
Latched
UNLA Unlatched
NO.CR Display Color in Normal condition
GRN
Green Color
REd
Red Color
AMbR Amber Color
MOdE Data Flow Mode
HOSt
Host Mode
SLAV Slave Mode
bAUd Baud Rate
300..
Baud Rate Value
..19200
FORM Data Format
7O1
7 Bit, Odd,
7E1
7 Bit, Even,
1 Stop Bit
1 Stop Bit
8N1
8 Bit, No parity,
1 Stop Bit
COMM Communication Standard
232
RS-232 Standard 485
RS-485 Standard
AddR Device Address
0000.. Address Value
..0099
INtF
Interface Device
dRNt
DRN with
dRNP DRN with
Temperature Input
Process Input
Miscellaneous:
PEAk Peak Value
VALL Valley Value
PROC Process Value
RUN
Run Mode
OVLd Input Overload
StOR Stored Message
d
a
Alarm
Alarm
Alarm
Alarm
Alarm
Alarm
1. In Slave Mode the Big Display will wait for
commands and data from the Serial Bus.
2. In Host Mode the Big Display will send data
automatically and continuously into the Serial Bus.
3. When used in RS-485 Mode, the device must be
accessed with an appropriate Address Value.
4. Latched Mode: Alarm remains latched until reset.
To reset already latched alarm select any menu
items and then press “up” or “down” button.
a
a
a
Below is a flowchart showing how to navigate through all menus by pressing front buttons.
FLOW CHART
d
a
d
a
d
a
d
a
d
a
d
d
a
d
a
d
a
d
a
d
_____Underline denotes factory default setup
DISPLAY ABBREVIATIONS
Temperature Stability:
50 ppm/°C
Display:
6-digit, 7-segment LED,
101.6mm (4.00”) with red, green
and amber programmable colors.
Alarm:
Alarm 1 & 2 programmable,
Latch/Unlatch, High, Low,
High/Low
SERIAL INTERFACE
Communication Standard:
RS-485, RS-422 or RS-232
Transfer speed (Baud rate):
300, 600, 1200, 2400, 4800,
9600,19200 bps
Data Format:
7O1-7 bit, Odd, 1 stop bit,
7E1- 7 bit,even, 1 stop bit
8N1 – 8 bit, No parity, 1 stop bit
Multi-Point Address (RS-485):
0 to 199
Flow Control:
No Flow control
OPERATION MANUAL
Screw terminals for
RS-232/485/422 interface
Power Supply:
100-240 Vac ±10%,
50/60 Hz, 22.5 W
Operating Temperature:
0 to 40°C
Storage Temperature:
-20 to 60°C
Relative Humidity:
0 to 85%
Protection:
NEMA-4x (IP65)
Dimensions:
641.6 L x 210.8 W x 95.4 D mm
(25.26" x 8.31" x 3.76")
Panel Cutout:
596.9 L x 179.4 W mm
(23.50” L x 7.06” W)
Weight:
3,175 g (7.0 lbs)
Approvals:
per EN61010-1:2001
RoHS 2 Compliant
iLD46-C2
Big Remote Display
with RS-232 Input
WARNING: These products are not designed for use in, and should not be used for, patientconnected applications.
This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains important
information relating to safety and EMC.
®
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OEMGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
TRADEMARK NOTICE:
®
,
omega.com
®
OMEGAnet® On-Line Service
www.omega.com
®
®
,
, and
™ are Trademarks of
OMEGA ENGINEERING, INC.
Internet e-mail
info@omega.com
Servicing North America:
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of
one (1) year from the date of purchase. In addition to OMEGA’s standard warranty period, OMEGA Engineering will
extend the warranty period for four (4) additional years if the warranty card enclosed with each instrument is
returned to OMEGA.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will
issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA,
if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply
to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing,
operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit
shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive
corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components which wear are not warranted, including but not limited to
contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither
assumes responsibility for any omissions or errors nor assumes liability for any damages that result from
the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA
warrants only that the parts manufactured by it will be as specified and free of defects. OMEGA MAKES NO
OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED,
EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION
OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with
respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or
otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event
shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications
or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application,
used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic
WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless
from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR)
NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the outside of the return package and on any
correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in
transit.
FOR WARRANTY RETURNS, please have the
following information available BEFORE
contacting OMEGA:
1. Purchase Order number under which the product
was PURCHASED,
2. Model and serial number of the product under
warranty, and
3. Repair instructions and/or specific problems
relative to the product.
FOR NON-WARRANTY REPAIRS, consult OMEGA for
current repair charges. Have the following information
available BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST of the
repair,
2. Model and serial number of product, and
3. Repair instructions and/or specific problems
relative to the product.
USA:
ISO 9001 Certified
Canada:
PATENT AND TRADEMARK NOTICE: This product is covered by one or more of the following patents: U.S. Pat.
No. Des. 336,895; 5,274,577; 6,243,021/ CANADA 2052599; 2052600/ ITALY 1249456; 1250938/ GERMANY DE 41
34398 C2/ SPAIN 2039150; 2048066/ UK Patent No. GB2 249 837; GB2 248 954/ FRANCE BREVET NO. 91 12756.
Other U.S. and International Patents pending or applied for.
M4194/0505
976 Bergar
Laval (Quebec) H7L 5A1
TEL: (514) 856-6928
e-mail: info@omega.ca
FAX: (514) 856-6886
For immediate technical or application assistance:
USA and Canada:
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA®
Customer Service: 1-800-622-2378 / 1-800-622-BEST®
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN®
Mexico and
Latin American:
TEL: (001)800-TC-OMEGA®
FAX: (001) 203-359-7807
En Español: (001) 203-359-7803
e-mail: espanol@omega.com
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen, The Netherlands
TEL: +31 20 3472121
FAX: +31 20 6434643
Toll Free in Benelux: 0800 0993344
e-mail: sales@omegaeng.nl
Czech Republic:
Frystatska 184, 733 01 Karviná
TEL: +420 59 6311899
e-mail: info@omegashop.cz
FAX: +420 59 6311114
France:
11, rue Jacques Cartier, 78280 Guyancourt
TEL: +33 1 61 37 29 00 FAX: +33 1 30 57 54 27
Toll Free in France: 0800 466 342
e-mail: sales@omega.fr
Germany/Austria:
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 7056 9398-0
FAX: +49 7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: info@omega.de
United Kingdom:
One Omega Drive
River Bend Technology Centre
Northbank, Irlam Manchester M44 5BD United Kingdom
TEL: +44 161 777 6611 FAX: +44 161 777 6622
Toll Free in England: 0800 488 488
e-mail: sales@omega.co.uk
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
© Copyright 2005 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without
the prior written consent of OMEGA ENGINEERING, INC.
One Omega Drive, P.O. Box 4047
Stamford CT 06907-0047
TEL: (203) 359-1660
FAX: (203) 359-7700
e-mail: info@omega.com
ISO 9002 Certified
DESCRIPTION:
The iLD46 is a 6-digit master/slave display providing remote readout
from instruments such as programmable controllers, digital panel
meters and other instruments with serial output. Communication
interfaces supported are RS-232 or RS-485 standards. Both
RS-232 or RS-485 are programmable through front panel buttons.
Mounting Big Display on Bail:
1. Mark the location of mounting screws on the flat surface.
2. Be sure to leave enough room around the bail to allow for
removal and rotation of the display.
3. The display can be rotated for the best viewing angle.
Disassembly Instruction:
Computer Card
or Converter Box
Pin Function
A, -Tx/-Rx
B, +Tx/+Rx
COM
Device with
RS-485 Pin
Function
-Tx/-Rx
+Tx/+Rx
COM
Remote Display
RJ-12
4
3
Screw Terminal
3
2
1
Example 2:
Alarm 1 setup: “ON”, Alarm Mode Low “A1LO”, Alarm Low
Value “LO-1”=100, Alarm Color “A1CR”=Amber
Alarm 2 setup: “ON”, Alarm Mode LO “A2LO”, Alarm High
Value “LO-2”=300, Alarm Color “A2CR”=Red
Normal Color:
“NO.CR”=Green
Display colors change sequences:
The Big Display features a large three color programmable display
with the capabitity to change color every time an Alarm is triggered.
SAFETY:
• The instrument is a panel mount device protected in
accordance with EN61010-1:2001.
EMC:
• Whenever EMC is an issue, always use shielded cables.
• Never run signal and power wires in the same conduit.
• Use signal wire connections with twisted-pair cables.
• Install Ferrite Bead(s) on signal wire close to the instrument if
EMC problems persist.
MOUNTING
0.50 [12.8]
Warning: Disconnect all ac power from the unit before
proceeding.
1. Remove all wiring connections from the rear of the instrument, by
unscrewing the power and input connectors.
2. Remove eight screws at the back of the display and back cover.
3. Remove the Big Display from the panel.
4. To remove the Big Display from the bail, unscrew the two
knobs at each end of the mounting brackets.
1. Wiring RS-232 Interface.
The RS-232 standard (point-to-point) allows a single device to be
connected to the Big Display using a three-wire connection (full
duplex).
COMM
9.28
[235.7]
2.25* [57.1]
XX.XXX*
FRONT VIEW
* MOUNTING HOLE
LOCATION
BRACKET MOUNT
WIRE PASS-THROUGH AREAS
MAX DIAMETER OF FITTINGS: 1.25 [31.8]
MAX PROTRUSION OF FITTINGS
INTO CASE: 0.50 [12.7]
1 3 5
2 4 6
RS232/485
COMM.
123456
TB4
1 2 3
TX
8.31
[210.9]
Device with RS-232
Pin Function
Receive (Rx)
Transmit (Tx)
Common Ground (COM)
PJ3
RX
3.76
[95.4]
24.68 [626.9]
1 2 1 2 3 4 5
+ -
RJ12 JACK
RTN
PANEL MOUNT
4.27 [108.6]
TB3
REMOTE
PROGRAMMER
25.26 [641.6]
3.35 [85.1]
REMOTE
DC PROGRAMMER
TB2
DC PWR
PANEL THICKNESS
0.625 [15.88] MAX
1 2 3
LN
AC PWR
PANEL CUTOUT
TB1
TX
RX
RTN
4 PLCS
AC PWR
7.06+0.02
[179.4+0.5]
DEVICE WITH
RS232 OUTPUT
Large Remote Display
RJ-12
Screw Terminal
4 (Tx)
3 (Tx)
3 (Rx)
2 (Rx)
5
1
2. Wiring RS-485 Interface.
The RS-485 standard (multipoint) allows a computer, one or more
devices and Big Displays (up to 32) to be connected using a twowire connection (half-duplex) plus a common wire to connect to the
shield of the cable. It is recommended to use shielded cable with
one twisted pair for EMI noise protection.
REAR VIEW
Example 3:
Alarm 1 setup: “ON”, Alarm Mode Low/High “A1LH”, Alarm Low
Value “LO-1”=100, Alarm High Value “HI-1”=250,
Alarm Color “A1CR”=Amber
Alarm 2 setup: “ON”, Alarm Mode Low/High “A2LH”, Alarm Low
Value “LO-2”=150, Alarm High value “HI-2”=200,
Alarm Color “A2CR”=Red
Normal Color:
“NO.CR”=Green
OPERATIONS
1. Peak Value (Display in Host Mode)
Press b to request “Peak” value:
a) RS-232 Mode, will send:
*X02 (Interface DRNT), or *X03 (Interface DRNP)
b) RS-485 Mode, will send:
*01X02 (Interface DRNT), or *01X03 (Interface DRNP)
In the examples for RS-485 it is assumed that the
device address is 01.
2. Valley Value (Display on Host Mode)
Press c to request “Valley” value.
a) RS-232 Mode, will send:
*X03 (Interface DRNT), or *X04 (Interface DRNP)
b) RS-485 Mode, will send:
*01X03 (Interface DRNT), or *01X04 (Interface DRNP)
4. Write alphanumeric characters to the Big Display
from the computer (Display in Slave Mode)
a) Single Big Display: (RS232) write 6 characters, then
CR (carriage return)
b) Multiple Big Display: (RS485) write *, device address
(2 digit), CR, 6 characters, then CR
Example 1:
Alarm 1 setup: “ON”, Alarm Mode High “A1HI”, Alarm High
Value “HI-1”=400, Alarm Color “A1CR”=Amber
Alarm 2 setup: “ON”, Alarm Mode High “A2HI”, Alarm High
Value “HI-2”=200, Alarm Color “A2CR”=Red
Normal Color:
“NO.CR”=Green
Display colors change sequences:
GREEN
I
RED
I
AMBER
•--➤-------------------------•--------------------------------•----------------➤
0
HI-2 = 200
HI-1 = 400
Connections to the computer are optional.
Display colors change sequences:
AMBER I
RED
I GREEN I
RED
I AMBER
•--➤---------•-----------------•-----------------•-----------------•-----------➤
0
LO-1 = 100 LO-2 = 150 HI-2 = 200 HI-2 = 250
CONFIGURATION
Button Functions in Configuration Mode
•
•
a
(MENU)
•
3. Process Value (Display on Host Mode)
Press d to request “Process” Value.
a) RS-232 Mode, will send: *X01
b) RS-485 Mode, will send: *01X01
5. Display Color Setup (Alarm Setup)
This menu allows the user to select the color of the display in
normal conditions and when alarm is triggered. If user wants the
Display to change color every time when both Alarm 1 and Alarm 2
are triggered, the Alarm values should be set in such a way that
Alarm 1 is always on the top of Alarm 2 value, otherwise value of
the Alarm 1 will overwrite value of Alarm 2 and Display color would
not change when Alarm 2 is triggered.
Mounting Big Display Through Panel:
1. Using the panel cutout diagram shown above, cut an opening in
the panel.
2. Remove eight screws at the back of Big Display to remove back
cover.
3. Insert the unit into the opening from the front of the panel, so the
gasket seals between the bezel and the front of the panel.
4. Align back cover to Big Display and reinstall screws.
AMBER I
RED
I
GREEN
--➤------------•-------------------------------•------------------------------ ➤--0
LO-1 = 100
LO-2 = 300
POWER
WIRING
23.50+0.02 [596.9+0.5]
+0.0
R 0.19 +0.00
-0.19 [4.8 -4.8 ]
3. Power Connection.
Connect the main power connections as shown in the figure below.
•
b
(UP)
•
•
•
c
(DOWN)
•
•
•
d
(ENTER)
•
To enter the Menu, the user must first press a button.
Use this button to advance/navigate to the next menu
item. The user can navigate through all the top level
menus by pressing a.
While a parameter is being modified, press a to
escape without saving the parameter.
Press the up b button to scroll through submenu
selections. When a numerical value is displayed press
this key to increase value of a parameter that is
currently being modified.
In the Run Mode pressing b causes the display
to flash the PEAK value several times before returning
to the Run Mode.
In the top menu press b causes the display to return to
the Run Mode.
Press the down c button to scroll through submenu
selections. When a numerical value is displayed press
this key to decrease value of a parameter that is
currently being modified.
In the Run Mode press c causes the display to flash
the Valley value several times before returning to the
Run Mode.
In the top menu press c causes the display to return to
the Run Mode.
Press this button to access the submenus from a Top
Level Menu item.
Press this button to store a submenu selection or after
entering a value – the display will flash a STOR
message to confirm your selection.
x, w, z, and some punctuations are non-printable characters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising