Omega | OM-CP-IFC200 and OM-CP-IFC202 | Owner Manual | Omega OM-CP-IFC200 and OM-CP-IFC202 Owner Manual

Omega OM-CP-IFC200 and OM-CP-IFC202 Owner Manual
Xxxxx
Xxxxxx
OM-CP-IFC200
/ OM-CP-IFC202
Data Logger
Xxxxx
XxxxxxInterface
Xxxxxxxx
INSTRUCTION
SHEET
M-5614/1116
M0000/0016
Shop online at omega.com SM e-mail: info@omega.com
For latest product manuals: www.omegamanual.info
OM-CP-IFC200 / OM-CP-IFC202
1. Setup USB Data Logger Interface
A
Insert the Omega Data Logger Software USB Flash Drive
into an available USB port on your PC. Click the Start menu
and choose Computer or My Computer. Browse to the
Removable Disk drive corresponding to the USB port you
selected.
For Windows 7 users, a dialogue box may appear with a
list of options. Select “Open Folder to view files.” If you are
not prompted, Click the Start menu and choose Computer
or My Computer. Browse to the Removable Disk drive
corresponding to the USB port you selected.
B
Click on the Omega Software link on the Contents screen
to start the install of the Data Logger Software. The Install
Omega Software window will appear, click on the Install
Omega Software link. Follow the on screen prompts to
complete the installation. Click Back to Omega Contents
when completed. See the Software Manual for additional
information.
2. Connect the USB Data Logger Interface
A
Connect the USB end of the OM-CP-IFC200/202 to the 6” USB
extender cable (optional but recommended). Plug the opposite end of
the cable into a USB port on the PC.
B
Once the OM-CP-IFC200/202 is plugged in, a New Hardware Found
message will appear on the PC. The new drivers will automatically
configure for use with the Interface Cable. A message will then
appear that the new hardware is installed and ready to use.
The installation of the USB data logger interface is complete.
Plug the stereo cable into the open jack on the OM-CP-IFC200/202 , the opposite end of the cable
will be plugged into the data logger.
Quick Start Manual
3. Test the Data Logger Interface Operation
A
To verify that the USB Interface drivers are installed properly, check to ensure the Data Logger Software can
recognize a device.
B
When the interface cable is connected to the PC the blue LED power indicator light should be on. If the
indicator light is not on, unplug the interface cable, wait 5 seconds and plug it back into the PC.
C
Start the Omega Data Logger Software. (If necessary, see the software manual for additional information
on the software)
D
Choose Select Comm Port from the Communication menu. A sub-menu will appear listing the available
communication ports. If the USB driver install was successful, and the USB interface is plugged into the PC,
then USB1 should appear as an option.
If multiple USB interface cables are connected to the computer they will be listed USB1, USB2, USB3, etc.
Use this menu to select the proper device.
E
The USB interface can be configured to work with most Omega Data loggers by selecting the proper baud
rate from the Select Baud Rate option under the Communications menu. The baud rate used by the logger
is listed on its label. For example the OM-CP-Temp101A communicates at 115,200 baud, so 115,200 must
be selected.
omega.com info@omega.com
U.S.A.
Headquarters:
Servicing North America:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from
any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only
that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the
product.
FOR NON-WARRANTY REPAIRS, consult OMEGA for current
repair charges. Have the following information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2016 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising