Omega | OM-CP-MOTOR101A | Owner Manual | Omega OM-CP-MOTOR101A Owner Manual

Omega OM-CP-MOTOR101A Owner Manual
Xxxxx
Xxxxxx
OM-CP-MOTOR101A
Xxxxx
Xxxxxx
Xxxxx
Xxxxxx
Xxxxxxxx
OM-CP-MOTOR101A-KIT
Xxxxx Xxxxxx Xxxxxxxx
Power Cycle Data Logging System
INSTRUCTION
SHEET
INSTRUCTION
SHEET
M0000/0016
MQS5780/0117
Shop online atM0000/0016
omega.com SM e-mail: info@omega.com
For latest product manuals:SMwww.omegamanual.info
Shop online at omega.com
e-mail: info@omega.com
For latest product manuals: www.omegamanual.info
OM-CP-MOTOR101A and OM-CP-MOTOR101A-KIT
Wiring the System
Wiring Example
The OM-CP-Motor101A has a two-position removable screw
terminal connection. It accepts 2-wire configurations. The OM-CPMotor101A measures and records on and off status changes of motors
other equipment drawing up to 200 Amps. The state change, or trip
set point, occurs when the current going through the switch exceeds
150mA’s. The split core switch allows for easy installation. (Warning: Note
the polarity instructions. Do not attach wires to the wrong terminals.)
For loads less than the trip point, wrap the wire around the body of the
device and through the center to increase the amount of current running
through the device until the trip point will be exceeded.
or
Product Notes
LEDs
Once started, the LED will flash at the selected reading rate to indicate that the device is running.
Engineering Units
Engineering units are used to convert one measurement reading to another. The software allows for software
level Engineering Units (conversion applied to data after download). Certain devices have device level
Engineering Units, which upon download automatically appear in the chosen unit of measure.
Installation Guide
Installing the Interface cable
- OM-CP-IFC200
Insert the device into a USB port. The drivers will install automatically.
Installing the software
Insert the Omega Software Flash Drive in an open USB port. If the autorun does not appear, locate the drive
on the computer and double click on Autorun.exe. Follow the instructions provided in the Installation Wizard.
OM-CP-MOTOR101A and OM-CP-MOTOR101A-KIT
Device Operation
Connecting and Starting the data logger
- Once the software is installed and running, plug the interface cable into the data logger.
- Connect the USB end of the interface cable into an open USB port on the computer.
- The device will appear in the Connected Devices list, highlight the desired data logger.
- For most applications, select “Custom Start” from the menu bar and choose the desired start method,
reading rate and other parameters appropriate for the data logging application and click “Start”. (“Quick
Start” applies the most recent custom start options, “Batch Start” is used for managing multiple loggers at
once, “Real Time Start” stores the dataset as it records while connected to the logger.)
- The status of the device will change to “Running”, “Waiting to Start” or “Waiting to Manual Start”,
depending upon your start method.
Note: The device will stop recording data when the end of memory is reached or the device is stopped. At this
point the device cannot be restarted until it has been re-armed by the computer.
Downloading data from a data logger
- Connect the logger to the interface cable.
- Highlight the data logger in the Connected Devices list. Click “Stop” on the menu bar.
- Once the data logger is stopped, with the logger highlighted, click “Download”. You will be prompted to
name your report.
- Downloading will offload and save all the recorded data to the PC.
Device Maintenance
Battery Replacement
Materials:
Small Phillips Head Screwdriver
Replacement Battery (OM-CP-BAT105)
- Puncture the center of the back label with the screw driver and unscrew the enclosure.
- Remove the battery by pulling it perpendicular to the circuit board.
- Insert the new battery into the terminals and verify it is secure.
- Screw the enclosure back together securely.
Note: Be sure not to over tighten the screws or strip the threads.
Recalibration
The OM-CP-Motor101A has a digital input signal and cannot be calibrated. A certificate of conformance can be
provided.
OM-CP-MOTOR101A and OM-CP-MOTOR101A-KIT
OM-CP-MOTOR101A and OM-CP-MOTOR101A-KIT
General Specifications
Description OM-CP-MOTOR101 and OM-CP-MOTOR101A-KIT
Resolution 1 second (reading rate dependent)
Memory 406,323 states
Sample Rate 4Hz to 1 every 24 hours
LED Indicator Red and Green
Required Interface Package OM-CP-IFC200
Baud Rate 115,200
Typical Battery Life 10 years typical
Operating Environment -15°C to +40°C, 10 to 90%RH non-condensing
Amperage Range 0.15 to 200Amps
Trip Point 0.15A (150mA) fixed (200mA AC for 50Hz operation)
Status Output N.O.1.0A@30VAC/DC
Housing Split Core
Material ABS Plastic
Dimensions
Weight
Data Logger: 1.4” x 2.5” x 0.6” (36mm x 64mm x 16mm)
Current Switch: 2.1” x 3.5” x 1.0” (54mm x 89mm x 16mm)
Without IFC200: 4oz (113g)
With IFC200: 9oz (255g)
Approval CE
Battery Warning
WARNING: FIRE, EXPLOSION, AND SEVERE BURN HAZARD. DO NOT SHORT CIRCUIT, CHARGE, FORCE OVER DISCHARGE, DISASSEMBLE,
CRUSH, PENETRATE OR INCINERATE. BATTERY MAY LEAK OR EXPLODE IF HEATED ABOVE 100 °C (212 °F).
Specifications subject to change. See Omega’s terms and conditions at www.omega.com
omega.com info@omega.com
U.S.A.
Headquarters:
Servicing North America:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from
any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only
that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:
1. Purchase Order number under which the product was
PURCHASED,
2. Model and serial number of the product under warranty, and
3. Repair instructions and/or specific problems relative to the
product.
FOR NON-WARRANTY REPAIRS, consult OMEGA for current
repair charges. Have the following information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems relative to the
product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2016 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising