Omega | PSW-700 Series | Owner Manual | Omega PSW-700 Series Owner Manual

Omega PSW-700 Series Owner Manual
User’s Guide
Shop online at
omega.com
e-mail: info@omega.com
For latest product manuals:
omegamanual.info
PSW-700 SERIES
Pressure Switches
OMEGAnet ® Online Service
omega.com
Internet e-mail
info@omega.com
Servicing North America:
U.S.A.:
One Omega Drive, P.O. Box 4047
Stamford, CT 06907-0047
TEL: (203) 359-1660
FAX: (203) 359-7700
e-mail: info@omega.com
Canada:
976 Bergar
Laval (Quebec) H7L 5A1, Canada
TEL: (514) 856-6928
FAX: (514) 856-6886
e-mail: info@omega.ca
ISO 9001 Certified
For immediate technical or application assistance:
U.S.A. and Canada: Sales Service: 1-800-826-6342/1-800-TC-OMEGA®
Customer Service: 1-800-622-2378/1-800-622-BEST®
Engineering Service: 1-800-872-9436/1-800-USA-WHEN®
Mexico:
En Español: (001) 203-359-7803
e-mail: espanol@omega.com
FAX: (001) 203-359-7807
info@omega.com.mx
Servicing Europe:
Czech Republic:
Frystatska 184, 733 01 Karviná, Czech Republic
TEL: +420 (0)59 6311899
FAX: +420 (0)59 6311114
Toll Free: 0800-1-66342
e-mail: info@omegashop.cz
Germany/Austria: Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
TEL: +49 (0)7056 9398-0
FAX: +49 (0)7056 9398-29
Toll Free in Germany: 0800 639 7678
e-mail: info@omega.de
United Kingdom:
ISO 9001 Certified
One Omega Drive, River Bend Technology Centre
Northbank, Irlam, Manchester
M44 5BD United Kingdom
TEL: +44 (0)161 777 6611
FAX: +44 (0)161 777 6622
Toll Free in United Kingdom: 0800-488-488
e-mail: sales@omega.co.uk
It is the policy of OMEGA Engineering, Inc. to comply with all worldwide safety and EMC/EMI
regulations that apply. OMEGA is constantly pursuing certification of its products to the European New
Approach Directives. OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any
errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, human applications.
PSW-700 Series
Explosion-Proof Pressure Switches
Part Numbers:
PSW-701-717
PSW-721-726
PSW-731-735
Please read all instructional literature carefully and thoroughly before starting.
Part I -Installation
GENERAL
Misuse of this product may cause explosion and
personal injury. These instructions must be
thoroughly read and understood before unit is
installed.
Tools Needed
Screwdriver
Adjustable Wrench to 1-1/2”
MOUNTING
This equipment is suitable for use in Class I, Divisions
1 & 2, Groups B, C and D; Class II, Divisions 1 & 2, Groups
E, f and G; class III; or non-hazardous locations only.
to prevent ignition, seal all conduit runs within 18
inches of enclosure.
Before Installing, check the sensor model selected
for compatibility to the process media in contact
with the sensor and wetted parts.
Always hold a wrench on the pressure housing hex
when mounting unit. Do not tighten by turning
enclosure. This will damage sensor and weaken
solder or welded joints.
PROOF PRESSURE* LIMITS STATED IN THE LITERATURE AND
ON NAMEPLATES MUSt never be exceeded, even by
surges in The system. Occasional operation of unit
up to maximum pressure is acceptable (e.g., start-up, testing).
continuous operation should not exceed the designated
over range pressure.
*Proof Pressure: The maximum pressure to which a pressure sensor
may be occasionally subjected, which causes no permanent damage
(e.g., start-up testing). The unit may require re-gapping.
These products do not have any field replaceable
parts. Any substitution of components may impair
suitability for Class I, Division 1.
To prevent ignition of hazardous atmospheres,
disconnect supply circuits before opening. keep
cover tight while circuits alive.
Install units where shock, vibration and temperature
fluctuations are minimal. Mount unit to prevent
moisture from entering the enclosure. It is
imperative to use properly rated explosion-proof sealing
fittings for electrical wire entry. Do not mount unit in
ambient temperatures lower than -40°F (-40°C) or higher
than 160°F (71°C).
PSW-721-726, 731-735 Enclosures are provided with
two 3/4” NPT electrical conduit openings, either of
which or both can be used during installation. A 3/4”
explosion proof plug is provided for properly sealing the
unused conduit opening. thE explosion proof plug must be
properly sealed during product installation.
Models PSW-701-717, 721-726, 731-735
The PSW-700 Series pressure switches are actuated when a bellows,
diaphragm or piston sensor responds to a pressure change. This
response at a pre-determined set point(s) actuates a SPDT or dual
SPDT snap-acting microswitch(es), which convert the pressure signal
into an electrical signal. Switch set point(s) may be varied by turning
the internal adjustment hex (PSW-721-726, 731-735 models) or the
external knob and pointer (PSW-701-717 models) according to the
procedures outlined.
Figure 1a:
PSW-701-717
www.omega.com
Figure 1b
PSW-721-726, 731-735
Mount controls vertically (pressure connection facing down, see Figure
1a) or horizontally (see Figure 1b). Control may be surface mounted via
the four 1/4” screw holes on the enclosure or mounting bracket. It can
also be mounted directly to a rigid pipe using the pressure connection.
Part II - Adjustments
WIRING
supply leadwires must be rated 75°C miniimum copper
conductor only.
Disconnect all supply circuits before wiring unit.
Wire units according to national and local electrical
codes. Maximum recommended wire size is 14 AWG. The
recommended tightening torque for field wiring terminals
is 7 to 17 IN-lbS.
Electrical ratings stated in literature and on nameplates must not be exceeded—overload on a switch
can cause failure on the first cycle.
Tools Needed
Screwdriver
5/8” Open End Wrench
5/64” Allen Wrench
After completing adjustments on types psw-701-717,
be sure to re-install adjustment cover. Do not over
tighten cover screws.
For set point adjustment and gapping, connect control to a calibrated
pressure source.
Models PSW-721-726, 731-735 (See Figure 3)
Remove cover. Loosen phillips screw adjustment lock. Adjust set
point by turning 5/8” hex adjustment screw clockwise (left) to raise
set point, or counterclockwise (right) to lower set point. Secure
adjustment screw by tightening adjustment lock.
To prevent seizure of enclosure cover, DO NOT remove
lubricant. Threads should also be free of dirt, etc.
The external Grounding terminal is not to be used
as the primary equipment grounding terminal. The
internal grounding terminal shall be used as the
primary equipment grounding means and the external
grounding terminal is only for a supplemental (secondary)
grounding connection where local authorities permit or
require such a connection.
Remove cover and wire control (See Figure 2). Replace cover and
hand tighten to fully engage cover O-ring.
Figure 3
DO NOT TURN
Models PSW-701-717
Models PSW-721-726, 731-735
Use 75˚C copper
conductors only.
Recommend tightening
torque for field wiring
terminals is 7-17 in-lbs.
NOTE REVERESE
WIRING OF LOW
SWITCH
Models PSW-701-717
Individual microswitches may be set together or apart by
up to 100% of range. When not set together, the front (Low)
microswitch can not be set higher than the rear (High)
microswitch (See figure 2 for switch layout). Turning external
knobs will increase or decrease each switch setting independently.
Re-Gapping Procedure For PSW-721-726, 731-735
Figure 2
Tools Needed
5/8” Open End Wrench
3/16” Open End Wrench (2)
gapping is factory-set and critical to the function of
the switch. this procedure should only be performed
if the plunger has accidentally been adjusted.
www.omega.com
1)Loosen adjustment lock.
2)Turn 5/8” hex adjustment screw clockwise (left), to approximately midrange. This puts a load on the sensor and exposes the plunger flats. (See Figure 4).
3)Using a 3/16” wrench on the plunger flats and a 3/16” wrench on the plunger hex screw, turn hex counter clockwise (right) from plunger until micro-switch actuates. If microswitch has already actuated, turn plunger hex screw clockwise (left) until microswitch deactuates.
4) Continue per following instructions, depending on model.
PSW-721-726
Turn hex clockwise (left) an additional 1-1/2 flats from this point. This will provide
a 5-9 mil gap.
PSW-731-735
Turn hex clockwise (left) 1 flat from this point. This will provide a 4-7 mil gap.
Figure 4
Dimensions
Internal Set Point Adjustment
PSW-721-726, 731-735
Models
Dimension A
Inches
mm
NPT
7.44
8.84
1/2
1/2
Pressure
PSW-731-735
PSW-721-726
189.0
224.5
External Set Point Adjustment
PSW-701-717
Dimension A
Inches
mm
NPT
PSW-701, 711-714
PSW-702-704, 708-709
8.09
8.50
205.5
215.9
1/4
1/2
PSW-705-707
PSW-710
PSW-715-717
7.81
8.75
8.31
194.4
222.3
211.1
1/4
1/4
1/4
Models
Pressure
Pressure Connections
PSW-701, 711-714
PSW-702-704, 708, 709
PSW-731-735
PSW-705-707
www.omega.com
PSW-710, 715-717
PSW-721-726
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a
period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month
grace period to the normal one (1) year product warranty to cover handling and shipping time. This
ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service
Department will issue an Authorized Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no
charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser,
including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of
having been tampered with or shows evidence of having been damaged as a result of excessive corrosion;
or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating
conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not
limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However,
OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any
damages that result from the use of its products in accordance with information provided by
OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the
company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR
REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF
LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of
OMEGA with respect to this order, whether based on contract, warranty, negligence,
indemnification, strict liability or otherwise, shall not exceed the purchase price of the
component upon which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic
Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical
applications or used on humans. Should any Product(s) be used in or with any nuclear installation or
activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility
as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify
OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the
Product(s) in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE
RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN
(AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID
PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return
package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent
breakage in transit.
FOR WARRANTY RETURNS, please have the
following information available BEFORE
contacting OMEGA:
1. Purchase Order number under which the product
was PURCHASED,
2. Model and serial number of the product under
warranty, and
3. Repair instructions and/or specific problems
relative to the product.
FOR NON-WARRANTY REPAIRS, consult OMEGA
for current repair charges. Have the following
information available BEFORE contacting OMEGA:
1. Purchase Order number to cover the COST
of the repair,
2. Model and serial number of the product, and
3. Repair instructions and/or specific problems
relative to the product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords
our customers the latest in technology and engineering.
OMEGA is a registered trademark of OMEGA ENGINEERING, INC.
© Copyright 2008 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied,
reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the
prior written consent of OMEGA ENGINEERING, INC.
www.omega.com
Where Do I Find Everything I Need for
Process Measurement and Control?
OMEGA…Of Course!
Shop online at omega.com SM
TEMPERATURE
�
�
�
�
�
�
�
�
�
�
Thermocouple, RTD & Thermistor Probes, Connectors, Panels & Assemblies
Wire: Thermocouple, RTD & Thermistor
Calibrators & Ice Point References
Recorders, Controllers & Process Monitors
Infrared Pyrometers
PRESSURE, STRAIN AND FORCE
�
�
�
�
�
�
�
�
Transducers & Strain Gages
Load Cells & Pressure Gages
Displacement Transducers
Instrumentation & Accessories
FLOW/LEVEL
�
�
�
�
�
�
�
�
Rotameters, Gas Mass Flowmeters & Flow Computers
Air Velocity Indicators
Turbine/Paddlewheel Systems
Totalizers & Batch Controllers
pH/CONDUCTIVITY
�
�
�
�
�
�
�
�
pH Electrodes, Testers & Accessories
Benchtop/Laboratory Meters
Controllers, Calibrators, Simulators & Pumps
Industrial pH & Conductivity Equipment
DATA ACQUISITION
�
�
�
�
�
�
�
�
�
�
Data Acquisition & Engineering Software
Communications-Based Acquisition Systems
Plug-in Cards for Apple, IBM & Compatibles
Datalogging Systems
Recorders, Printers & Plotters
HEATERS
�
�
�
�
�
�
�
�
�
�
Heating Cable
Cartridge & Strip Heaters
Immersion & Band Heaters
Flexible Heaters
Laboratory Heaters
ENVIRONMENTAL
MONITORING AND CONTROL
�
�
�
�
�
�
�
�
�
�
�
�
Metering & Control Instrumentation
Refractometers
Pumps & Tubing
Air, Soil & Water Monitors
Industrial Water & Wastewater Treatment
pH, Conductivity & Dissolved Oxygen Instruments
M1102/0708
IMPSW700-02
www.omega.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising