Omega | PX26 Series | Owner Manual | Omega PX26 Series Owner Manual

Omega PX26 Series Owner Manual
PX26 SERIES
Pressure Transducers
INSTRUCTION
SHEET
M1608/1018
Shop online at: omega.com e-mail: info@omega.com
For latest product manuals: omegamanual.info
GENERAL INFORMATION
Omega’s Pressure sensors are four-active piezoresistive bridge devices. When pressure is applied, a different output voltage
proportional to that pressure, is produced.
Wet/Wet Differential Pressure Sensors simultaneously accept independent pressure sources. Gage Pressure Sensors provide
a form of differential pressure measurement in which atmospheric pressure is used as a reference.
The PX26 is available in variety of PSI ranges and as differential and gage sensors:
MODEL NUMBER (GAGE)
PX26-001GV
PX26-005GV
PX26-015GV
PX26-030GV
PX26-100GV
PX26-250GV
RANGE
0-1 PSIG
0-5 PSIG
0-10 PSIG
0-30 PSIG
0-100 PSIG
0-250 PSIG
MODEL NUMBER (DIFFERENTIAL)
PX26-001 DV
PX26-005DV
PX26-015DV
PX26-030DV
PX26-100DV
PX26-250DV
RANGE
0-1 PSID
0-5 PSID
0-15 PSID
0-30 PSID
0-100 PSID
0-250 PSID
UNPACKING
Remove the packing list and verify that all equipment has been received. If there are any questions about the shipment,
please call Omega Customer Service Department at 1-800-622-2378 or 203-359-1600. We can also be reached on the Internet
at omega.com e-mail: info@omega.com
Upon receipt of shipment, inspect the container and equipment for any signs of damage. Take particular note of any
evidence of rough handling in transit. Immediately report any damage to the shipping agent.
NOTE:
The carrier will not honor any claims unless all shipping material is saved for their examination. After examining and
removing contents, save packing material in event reshipment is necessary.
MEDIA COMPATIBILITY
Input media are limited to those media which will not attack polyester,
flurosilicon, or silicon, such as oils, lacquer thinner, hydraulic fluid, most
petroleum products, water and salt water. Not recommended for freons.
SOLDERING
Limit soldering temperature to 600°F (315°C) for 10 seconds duration
maximum.
ELECTRICAL CONNECTION
NOTCHED (PIN 1)
–
+
+ METER –
1
2
3
4
WARNING! READ BEFORE INSTALLATION
Fluid hammer and surges can destroy any pressure transducer and must always be avoided. A pressure snubber should
be installed to eliminate the damaging hammer effects.
Fluid hammer occurs when a liquid flow is suddenly stopped, as with quick closing solenoid valves. Surges occur when
flow is suddenly begun, as when a pump is turned on at full power or a valve is quickly opened.
Liquid surges are particularly damaging to transducers if pipe is original empty. To avoid damaging surges, fluid lines
should remain full (if possible), puts should be up to power slowly, and valves opened slowly. To avoid damage from both
fluid hammer and surges, a surge chamber should be installed, and a pressure snubber should be installed on every
transducer.
Symptoms of fluid hammer and surges damaging effects:
a) Pressure transducer exhibits an output at zero pressure (large zero offset). If offset is less than 10% FS, user can usually
re-zero meter, install proper snubber and continue monitoring pressures.
b) Pressure transducer output remains constant regardless of pressure.
c) In severe cases, there will be no output.
SPECIFICATIONS
EXCITATION:
OUTPUT:
ACCURACY:
LINEARITY:
HYSTERESIS & REPEATABILITY:
ZERO BALANCE:
SPAN TOLERANCE:
STORAGE TEMPERATURE:
OPERATING TEMPERATURE:
COMPENSATED TEMPERATURE:
THERMAL EFFECTS:
(25 to 50°C, 25 to 0°C)
PROOF PRESSURE:
INPUT RESISTANCE:
OUTPUT RESISTANCE:
RESPONSE TIME:
SHOCK:
VIBRATION:
GAGE TYPE:
WETTED PARTS:
MATING CONNECTOR:
PRESSURE PORT:
ELECTRICAL CONNECTION:
WEIGHT:
10Vdc, 16Vdcmax @ 2mA
100mV, 1 10mV/V
(16.7mV, 1.67mV/V for
1 PSI range)
(50mV, 5mV/V for 5PSI range)
1% FS
1.0% FS BFSL
0.2% FS
±1.5mV
±3.0 mV
-67° to 212°F (-55° to 100°C)
-40 to 185°F (-40° to 85°C)
32° to 122°F (0° to 50°C)
ZERO: 1 mV
SPAN: 1% Rdg
20 PSI for 1 and 5 PSI range
45 PSI for 15 PSI range
60 PSI for 30 PSI range
200 PSI for 100 PSI range
500 PSI for 250 range
7.5k Ω
2.5k Ω
1 msec.
Qualified to 150 G
Qualified to 2kHz @ 20 G sine
Silicon sensor
Polyester, Silicon, flurosilicon
CX136-4, not included
0.20" dia. & 0.25" collar dia.
Pin 1 +EXC (notched)
Pin 2 +OUT
Pin 3 –EXC
Pin 4 –OUT
Approx 0.07 oz (2 gm)
O 6.4
O .25
O 1.2
O 5.1
O .05
O .20
Gage Sensor
8.0
.31
10.2
2.79
.110
2.3
.09
4X 0.5
4X .02
.40
4X 1.0
4X .04
Pressure is applied
to Port P2
Port P 1 vents to
ambient pressure
3X 2.5
3X .10
21.8
.86
4X 0.41
4X .016
12.7
1.7
.50
.06
O 1.2
O 6.4
O .05
O .25
Differential
Sensor
8.0
.31
O 5,1
2.79
O .20
.110
2.3
3X 2.5
Port P 1 is near
terminals.
.09
4X 1.0
3X .10
4X .04
4X 0.5
1.3
.05
4X .02
PORT P2
21.8
.86
34.4
1.35
4X 0.41
4X .016
1.7
.06
12.7
.50
PORT P1
omega.com info@omega.com
U.S.A.
Headquarters:
Servicing North America:
Omega Engineering, Inc.
Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660
Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the
right to alter specifications without notice.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months
from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product
warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an
Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found
to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from
any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits,
improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with
or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper
specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not
warranted, include but are not limited to contact points, fuses, and triacs.
OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes
responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its
products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only
that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER
WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF
TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth
herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty,
negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10
CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any
Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way,
OMEGA assumes no responsibility as set forth in our basic WARRANTY / DISCLAIMER language, and, additionally, purchaser will
indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in
such a manner.
RETURN REQUESTS / INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
The purchaser is responsible for shipping charges, freight, insurance and proper packaging to prevent breakage in transit.
FOR WARRANTY RETURNS, please have the following
information available BEFORE contacting OMEGA:
1.Purchase Order number under which the product was
PURCHASED,
2.Model and serial number of the product under warranty, and
3.Repair instructions and/or specific problems relative to the
product.
FOR NON-WARRANTY REPAIRS, consult OMEGA for current
repair charges. Have the following information available BEFORE
contacting OMEGA:
1. Purchase Order number to cover the COST of the repair,
2. Model and serial number of the product, and
3.Repair instructions and/or specific problems relative to the
product.
OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and
engineering. OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic
medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising