ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW 5 6 WARRANTY/DISCLAIMER OMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 13 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANTY does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. This WARRANTY is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs. OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use if its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages. CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANTY/DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of the Product(s) in such a manner. RETURN REQUESTS/INQUIRIES Direct all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RETURNING ANY PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN AUTHORIZED RETURN (AR) NUMBER FROM OMEGA’S CUSTOMER SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence. FOR WARRANTY RETURNS, please have the following information available BEFORE contacting OMEGA: 1. Purchase Order number under which the product was PURCHASED, 2. Model and serial number of the product under warranty, and 3. Repair instructions and/or specific problems relative to the product. FOR NON-WARRANTY REPAIRS, consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA: 1. Purchase Order number to cover the COST of the repair or calibration, 2. Model and serial number of the product, and 3. Repair instructions and/or specific problems relative to the product. OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. This affords our customers the latest in technology and engineering. OMEGA is a registered trademark of OMEGA ENGINEERING, INC. © Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved. This document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC. MQS5417/0717 Hardware Transmitter Diagram RED/YELLOW LED POWER SWITCH Wiring Diagrams UWBT-TC-M12 Wiring The TC models use standard pin connections, as shown below: I O – TC#1 – + TC#1 + TC#2 (OPTIONAL) TC#2 (OPTIONAL) MINI-B USB Rear Label The rear label is marked with international safety and hazard symbols in accordinance with IEC standards. UWBT-RTD-M12 Wiring PIN #4 PIN #1 IEC SYMBOL: EU’s WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT COMPLIANCE IEC SYMBOL: CAUTION, REFER TO ACCOMPANYING DOCUMENTATION NOTE: It is recommended that you recharge your transmitter when you reach 20% battery level or lower. Transmitter LED Indication Table (The red & yellow colors come from one LED) Red LED Yellow LED State State Green LED Transmitter Status Blinking - Blinking Sensor Out of Range Blinking - Blinking Sensor Open Red LED blinks twice every 2 seconds. Blinking - - Low or High Alarm Red LED blinks every 5 seconds. Blinking - - Low Battery Green LED blinks every second. - - Blinking Downloading data from probe Green LED blinks 3 times every 3 seconds. - - Blinking Device Paired/ Data being sent Green LED blinks twice every 3 seconds. - - Blinking Internal logging on Green LED blinks once every 3 seconds. - - Blinking The transmitter is on and connected to a sensor, but is not paired with a smart device. Blinking - - Device unpaired Red LED blinks every second for 2 minutes, then stops. Blinking - - Transmission enabled (searching to pair) Red & Green LEDs blink twice together, then go off. Blinking - Blinking - On - Battery Charging Battery Fully Charged Yellow LED blinks every second. - Blinking - Green & Red LEDs turn on for ½ second, then go off. On - On Red LED turns on for ½ of a second, then goes off. On - - - - Blinking Blinking Blinking - Green LED blinks 3 times, then the transmitter turns off. Yellow & Red LEDs blink alternatively. PIN #2 PIN #3 diagram below: UWBT-RTD-TB Terminal Block Wiring The UWBT-RTD-TB comes with a 3-wire terminal block. The terminal block can be unplugged from the handle, allowing for easier handling of the wires. See below: ANSI & IEC: RED Handheld Bluetooth® Wireless Temperature, Humidity and pH Transmitter Series UWBT-TC UWBT-RTD UWBT-RH UWBT-PH ANSI: BLACK (IEC: WHITE) Red & Green LEDs blink alternatively. Yellow LED is on continuously. UWBT SERIES ANSI: BLACK (IEC: WHITE) Red & Green LEDs blink alternatively. Red LED blinks every second for 2 minutes, then unit switches off. PIN #1 PIN #2 PIN #3 R RoHS 2 Compliant GREEN LED PAIR BUTTON LED Action For complete product manual: www.omega.com/manuals/manualpdf/M5417.pdf Factory Settings have been successfully re-installed on the transmitter. 3-WIRE RTD ANSI & IEC: RED ANSI: BLACK (IEC: WHITE) 2-WIRE RTD Additional Information Please visit the Omega website and download the full-length UWBT manual for more information on the UWBT transmitter and its applications. www.omega.com/uwbt ® omega.com email@example.com Transmitter has been powered up successfully Transmitter has failed to power up successfully Transmitter has successfully poweredoff Transmitter internal memory is full. The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG, Inc. and any use of such marks by OMEGA is under license. iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used by Apple under license. Android is a trademark of Google, Inc. Other trademarks and trade names are those of their respective owners. U.S.A. Headquarters: Servicing North America: Omega Engineering, Inc. Toll-Free: 1-800-826-6342 (USA & Canada only) Customer Service: 1-800-622-2378 (USA & Canada only) Engineering Service: 1-800-872-9436 (USA & Canada only) Tel: (203) 359-1660 Fax: (203) 359-7700 e-mail: firstname.lastname@example.org For Other Locations Visit omega.com/worldwide ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW START HERE 2 3 Software Notes For (iOS & Android™) NOTE: Having the transmitter paired with the UWBT app does not mean that transmission is active. You must either be in the “Display” or “Settings” screens, or be logging data, for the Bluetooth® wireless transmission to be active. Otherwise, the transmitter will unpair after 2 minutes. NOTE: Pairing Within the UWBT App: 1. M ake sure your UWBT transmitter is switched on and that the Bluetooth wireless communication to the smart device has already been established. See “Pairing within smart device Settings menu (iOS operating system only)” in the previous section for details on this process. 2. Open the UWBT app. 3. I n the UWBT app, go to the ‘Transmitter Pairing’ settings. Software For (Android) Initial Pairing Instructions In order to start communicating with the UWBT transmitter, you need to pair it with your smart device via Bluetooth wireless communication. Pairing within the UWBT App: 1. Make sure your UWBT transmitter is switched on. 2. Open the UWBT app. 3. In the UWBT app, go to the ‘Transmitter Pairing’ settings 4. Hold down the transmitter’s ‘Pair’ button for 2 seconds – this will put the sensor in discovery mode. 4. I n the ‘Discovered Devices’ list, select the transmitter you would like to pair with. 5. In the ‘Discovered Devices’ list, select the transmitter you would like to pair with. 6. Click on the ‘Pair’ button. 7. The smart device will create a prompt asking if you would like to pair with the specific transmitter. Click ‘Yes’. (Please note that this prompt only pops up during your first time pairing with a transmitter.) You cannot pair the same transmitter with multiple smartphones or tablets. In order to view a transmitter’s information on a different tablet, you will need to unpair the transmitter from the UWBT app. Software For (iOS) Initial Pairing Instructions In order to start communicating with the UWBT transmitter, you need to pair it with your smart device via Bluetooth wireless communication. For devices that work with the iOS operating system, you must pair within the iOS settings before pairing within the UWBT app. Devices for Android only require pairing from within the UWBT app. Pairing within smart device Settings menu (iOS only): 1. Switch on your UWBT transmitter. 2. Hold down the transmitter’s ‘Pair’ button for 2 seconds – this will put the sensor in discovery mode. 3. Go to the Settings page of your smart device 4. Select the Bluetooth wireless section 5. Make sure your Bluetooth wireless functionality is turned on – the Bluetooth wireless slider should be showing a green background. 6. Tap the device to be paired via Bluetooth wireless communication. ARTWORK/PRODUCT ART/ DWGS/START HERE ARROW 4 Software (PC) Installing the PC Application To install the UWBT PC application on your computer follow these steps: 1. Download the latest UWBT PC application release from our website at ftp://ftp.omega. com/public/DASGroup/products/ 2. After download is completed, open the directory where the download was saved 3. Click and run the UWBT PC app executable file (.exe). The application and its drivers will be installed automatically. 4. After application is fully installed, a shortcut is created on your computer desktop and “UWBT Libusb” directory is created in the C: drive of your PC. This directory contains the drivers for all UWBT transmitter models. Discover Transmitter: Clicking the “Discover Transmitter” button searches for UWBT transmitters connected to USB ports of the PC. The maximum number of UWBT transmitters that can be discovered is four. After being discovered, only one UWBT transmitter can be connected with the PC app at a time. • You can connect to any of the discovered transmitters by clicking the “Select” button next to the transmitter’s name. • You can also switch the transmitter you are connected to by clicking on the “Select” button next to the new transmitter of your choice. The application will automatically disconnect from the previous transmitter, and connect to the new one. 5. Click on the ‘Pair’ button. 6. You are ready to display and log data! NOTE: 8. You are ready to display and log data! The “Discover Transmitter” button’s name changes to “Disconnect Transmitter” after a UWBT device is connected.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project