Gigaset | DA610 | User guide | Gigaset DA610 User guide

Gigaset DA610 User guide
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / overview.fm / 22.03.2016
Overview Gigaset DA610
1
2
3
4
5
6
7
8
9
10
11
12
Display and keys
1 Display ( page 4)
2 Control key ( page 5)
3 Speed dial key
4 Set key
5 Redial/pause key
6 Recall key
7 Mute key
8 Star key, selecting/deselecting the ring tone (press and hold)
9 Hash key, selecting/deselecting the key lock (press and hold)
£
£
10 Hands-free key
11 Keys for setting the volume of the handset, speaker and ring tone
12 Microphone for hands-free use
@ Hands-free key
LED
¤
¤
en fr fa ar
flashes on incoming call
lights up when the call is transferred to the speaker
1
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / overview.fm / 22.03.2016
Connecting the telephone
¤
2
¤
Connect the telephone connector (1) to
the main telephone socket. Use the telephone cable supplied.
You may need a phone adapter depending
on your country. This is provided in most
cases.
Power is supplied over the telephone line.
A mains adapters is not necessary.
Guide the cable through the cable
channel (2).
1
¤
Connect the handset to the telephone
using the coiled cable (3).
3
Notes
u First use
1. Lift the handset for 5 seconds and place it back in the cradle.
2. Lift the handset again. You will hear the free tone and the device is now ready to be used.
The phone is connected to the power source via the phone line. In case of a power cut (e.g. if the PBX is switched off at night), the above mentioned steps need to be repeated. Phonebook entries and speed dialling destinations are stored indefinitely.
u The device is designed to be used as a single-line system (on the main extension or a telephone system).
It cannot be operated as a second phone on a line splitter.
u Operation on a PBX or router
The private branch exchange (PBX) or the router must supply the phone with continuous DC voltage, even when ringing. If this is not the case,
the phone may switch off briefly when ringing. As a result, saved information may be lost. Refer to the operating manual for your PBX or router
for information in this regard or contact the manufacturer.
2
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / DA610IVZ.fm / 22.03.2016
Table of contents
Overview Gigaset DA610 . . . . . . . . . . . . . . . . . . . . 1
Connecting the telephone . . . . . . . . . . . . . . . . . . 2
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting up the telephone for use . . . . . . . . . . . . . 4
Operating the telephone . . . . . . . . . . . . . . . . . . . . 4
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writing and editing names and numbers . . . . . . . . . . . . . . . . . . .
Text input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5
5
5
Other settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Standard characters . . . . . . . . . . . . . . . . . . . . . . . . 12
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Questions and answers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Contacts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Telephoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Making a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Incoming calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using open listening / hands-free . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings during a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
6
7
Using the phonebook . . . . . . . . . . . . . . . . . . . . . . .
Using the call list (CLIP) . . . . . . . . . . . . . . . . . . . . . .
Using speed dialling numbers. . . . . . . . . . . . . . . .
Adjusting the telephone . . . . . . . . . . . . . . . . . . . .
7
8
8
8
Changing the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the handset volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
9
9
9
Security settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Locking the telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Emergency calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Direct calling (baby call) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Blocking numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Network services . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Caller display (CLIP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting up a dialling code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation on a PABX . . . . . . . . . . . . . . . . . . . . . . . 11
Special functions/Recall key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the dialling mode/flash time . . . . . . . . . . . . . . . . . . . . 11
Setting dialling prefixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
en fr fa ar
3
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Safety precautions
Operating the telephone
When installing, connecting and operating the telephone, always
observe the following precautions:
u Only use the jacks and leads supplied.
u Only connect the connecting lead to the intended socket.
u Only connect the approved accessories
u Lay the connecting lead where it will not cause accidents.
u Position the telephone on a non-slip surface.
u For your safety and protection, the telephone may not be used in the
bath or shower rooms (wet locations). The telephone is not splash
proof.
u Never expose the telephone to sources of heat, direct sunlight or
other electrical devices.
u Protect your telephone from moisture, dust, corrosive liquids and
vapours.
u Never open up the telephone yourself.
u Do not touch the plug contact with pointed or metallic objects.
u Do not carry the telephone by the leads.
u If you give your Gigaset DA610 to someone else, make sure you also
give them the operating manual. Your Gigaset DA610 has a permanent memory, so you may want to delete any stored numbers before
passing it on.
The keypad and the display are available to operate your Gigaset DA610.
All usage possibilities are described in the handbook.
Note
Some of your telephone's functions may only be available without
restriction if they are supported by your and the caller's network provider, e. g. functions for which information on the caller's telephone
number is required.
This applies for the following functions, for example:
u Displaying the number of an incoming call ( page 6)
u Indicating a caller with VIP melody ( page 6)
u Call list ( page 8)
£
Display
Depending on the operating situation the display shows different information, e.g. date and time. You can set the date and time and the format
in which they are displayed ( page 9).
Symbols provide information on the status of your telephone.
£
01lo Zf i x m 24.12 18:30
Symbol bar: status, date
and time
Display of call duration,
numbers, names, phonebook and list entries,
settings
01--28
Setting up the telephone for use
Recommended installation of telephone:
u Do not expose the telephone to direct sunlight or other sources of
heat.
u Operate at temperatures of between + 5° C and + 40° C.
u Maintain a distance of at least one metre between the telephone
and radio equipment, e.g. radio telephones, radio paging equipment or TV sets. Otherwise telephone communication could be
impaired.
u Do not install the telephone in dusty rooms as this can limit the service life of the telephone.
u Furniture lacquer and polish can be adversely affected by contact
with parts of the unit (e.g. feet).
£
£
Display symbols
01
Number of an entry in the phonebook or a call list or of a
speed dial key
o
Setting mode activated
f
Flashes for a new entry in the call list if the caller's number
transmission (CLIP) is active ( page 11)
g
Phonebook open
i
Key lock activated
x
Ringer switched off
Mute mode activated
l
Flashes on incoming VIP call
Is indicated if at least one entry with activated VIP mode is
present in the phonebook ( page 7).
£
m
£
Display language
£
On delivery the display language is set to English. Other languages are
available and you can change the language if you wish ( page 8).
4
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Telephoning
Control key
You activate the functions and navigate the menus using the control
key. The functions offered depend on the operating situation.
W
T
t
s
u
v
V
U
In addition to the handset, you can also call using the speaker (handsfree function). In the following instructions, the symbol c also always
stands for @.
Y Open the call list
Z Open phonebook
In standby:
t
s
Making a call
Entering the telephone number using the keypad
c~
In lists:
Scrolls one entry upwards/downwards.
Hold down: Scrolls the list fast upwards/downwards.
While editing time setting:
Moves forwards/backwards one position.
In menus and lists: Exits the menu or list.
Dialling from the phonebook
£
If you have already saved numbers in your phonebook ( page 7), you
can make a call directly from the phonebook.
Open the phonebook using the control key s.
While editing names and numbers:
Deletes the character to the left of the cursor.
Hold down: Deletes the line.
If the entry is empty: Exits the editing mode.
Phone number entered: Dials the phone number.
In lists: Opens the context menu.
While editing entries: Saves the edits.
Z
Searching for an entry
q
Select an entry.
~
or
Writing and editing names and numbers
~
Lift the handset, dial the number.
Instead of lifting the handset:
@
Press the hands-free key to make a call via the speaker.
You can switch over at any time during the conversation.
£
Enter letters ( page 5). The first entry starting with this
letter is displayed.
Dialling numbers
c
Lift the handset.
Text input
Enter text using the keypad.
Multiple letters and numbers are assigned to each key between
and O and Q, * and #. You enter a specific character
by pressing the corresponding key several times.
You will find a table of applicable characters in the Appendix page 12.
£
or
[
q
Moving the cursor
t s To move the cursor to the left/right in the text, press the
control key upwards/downwards.
Open the context menu.
Select DIAL ENTRY and confirm with [.
The call is initiated via the speaker. To make the call using
the handset, simply lift the handset.
Note
You can also first lift the handset before opening the phonebook.
Deleting/correcting characters
X
Press the left-hand side u of the control key. The character to the left of the cursor is deleted. Press and hold
down to delete the whole line.
en fr fa ar
5
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Dialling from the call list
Dialling pauses
The call list contains the numbers of the last 50 incoming calls.
Requirement: Telephone number display is possible for incoming calls
( page 11).
Multiple calls from one number are only displayed once (with the information of the last call). If the name is transmitted or the number is saved
to the phonebook, the accompanying name is also displayed.
Open the call list using the control key t.
q
Select the number or name.
£
Y
either ...
c
Open the context menu.
Select CALL BACK and initiate the call using the speaker
with [. To make the call using the handset, simply lift the
handset.
Note
You can also first lift the handset before opening the call list.
Dialling one of the last five numbers saved:
I
Press the redial key.
q
Select the number.
c
Lift the handset.
c
Lift the handset.
@
Press the hands-free key to accept the call via the speaker.
or
@&
Switching from open listening to hands-free:
Replace the handset while pressing the hands-free key.
Initiate the call using the speaker with [.
Switching hands-free on/off
You can also make a call via the microphone with the handset in the cradle. The optimum distance from the microphone is approx. 50 cm.
Deleting all redial numbers
K I # 2 5 Press the key sequence.
K
Press the set key or [ to confirm.
Switching on hands-free during a call
@ & Replace the handset while pressing the hands-free key.
Speed dialling
10 numbers can be saved for speed dial on the number keys 0 ... 9
( page 8).
J
Press the speed dial key.
Q ... O Press the speed dial number key.
c
Lift the handset, the @ key or initiate the call with [.
The number stored on the number key is dialled.
Note
You can also first lift the handset before pressing the speed dial key.
Accepting a call
The persons present in the room can listen to the call over the speaker.
During the call using the handset:
@
Press the hands-free key to switch open listening on or off.
When the speaker is switched on and the handset is picked up, open listening is switched on. In this case, the hands-free microphone is
switched off.
When the speaker is switched on and the handset is in the cradle, handsfree via the hands-free microphone is switched on.
Dialling the last saved number:
c I Lift the handset, press the redial key.
£
£
Incoming calls are indicated by the ring tone and in the display.
For number displays ( page 11), the number is visible in the display
and the f symbol flashes. This symbol disappears when you answer the
call or (if you don't answer) by calling up the call list. The name is also displayed for callers who are stored in the phonebook with names.
If the VIP mode is activated ( page 9) the VIP symbol flashes in the display and the VIP ring tone signals the call.
Switching open listening on/off
The last five numbers dialled are automatically saved (each a max. of
32 digits).
v
Incoming calls
Using open listening / hands-free
Last number redial
or
£
£
Lift the handset.
... or
[
q
One or more dialling pauses can be entered using I (not at 1st digit).
Pauses are transferred to the memory and are necessary for certain
extension systems (e.g. 0 I 2368).
The length of the pause can be set to 1, 3 or 6 seconds ( page 12).
Switching on hands-free prior to dialling
@
Hands-free key, wait for dial tone.
Switching off hands-free
c
Lift the handset during the call. The call is transferred to
the handset.
@
Ending a call
6
Press the hands-free key during a call via the speaker.
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Settings during a call
Opening the phonebook
Setting the handset volume
In standby:
There are three adjustable levels.
E / D Set the volume using the volume up/volume down keys.
The set volume is shown in the display.
Searching for an entry
Setting the speaker volume
Z
Press the control key s.
q
Select an entry.
~
or
There are seven adjustable levels.
During hands-free speaking or open listening:
E / D Set the volume using the volume up/volume down keys.
The set volume is shown in the display.
Note
If you press *, the entry is set as a VIP entry or the setting is
deleted.
Mute
£
You can switch off the microphone or handset and microphone during a
call according to the setting of the mute function ( page 9):
C
Press the mute key to switch the mute function on or off.
During muting of the microphone, a melody can be played.
Once the telephone has been muted this is indicated in the display with
the symbol.
m
Changing the ringer and ringer volume
While the telephone is ringing, the volume and ringer can be changed.
Changing the volume
E / D Set the ringer volume with the volume up/volume down
keys (5 levels, 0=silent).
Changing the melody
Q ... O Select the ringtone with the numeric keys (choice of 10).
£
#
Press the hash key to switch between number and name
display.
Z
Saving numbers
Open the phonebook.
The first entry in the list is displayed.
t
Select NEW ENTRY and confirm with [.
~
Enter number and confirm with [.
~
Enter name and confirm with [.
The entry is saved and shown in the display.
*
Press the star key to turn the entry into a VIP entry. Press
again to delete the setting.
Z
Your Gigaset DA610 contains a phonebook in which you can save up to
50 entries, each with a maximum of 32 digits for numbers and 14 characters for names.
You can make a call ( page 5), add new entries and manage and modify entries ( page 7) using the phonebook.
You can manually enter numbers and names or transfer them from the
call list ( page 8). You can also allocate VIP mode to a number.
The Z symbol is indicated in the display if the phonebook has been
opened. The phonebook entry number is also visible (01... 50). If there is
at least one VIP entry in the phonebook, this is indicated in the display
via the l symbol.
The phonebook provides the following functions in a menu:
£
Showing the number of an entry
Editing an entry
Using the phonebook
£
£
Enter letters ( page 5). The name of the first entry starting with this letter is displayed.
Open the phonebook.
The first entry in the list is displayed.
q
Select the entry and open the context menu with [.
q
Select EDIT ENTRY and confirm with [.
~
Change the number and confirm with [.
~
Change the name and confirm with [.
[
Confirm the saving of the entry in the phonebook.
Z
Deleting an entry / Deleting all entries
Open the phonebook.
The first entry in the list is displayed.
q
Select an entry and open the context menu with [.
q
Select DELETE ENTRY to delete the selected entry or
DELETE ALL to delete all entries and confirm with [.
[
Press the control key to confirm the action.
NEW ENTRY
Entry 1-50
...
DIAL ENTRY
EDIT ENTRY
NEW ENTRY
DELETE ENTRY
DELETE ALL
en fr fa ar
7
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Using the call list (CLIP)
Using speed dialling numbers
£
Incoming calls are saved if the number is transmitted ( page 11). Up to
50 calls are saved. If the number is the same, only the last incoming call
is saved. The oldest call is automatically deleted when there are more
than 50 calls. If transmitted, the caller’s name is also displayed. If the
caller is saved to the phonebook, the phonebook name is used. If there
are any missed calls in the list the f symbol flashes.
You can use the call list for the following functions:
Calling a number from the list ( page 6).
Saving a number in the phonebook.
The call list provides the following functions in a menu:
¤
¤
£
Entry 1-50
CALL BACK
SAVE NUMBER
DELETE ENTRY
DELETE ALL
Opening the call list
Y
You can open the call list in idle mode or when the handset is lifted.
Press the control key t.
Viewing an entry
q
Select an entry.
If the number and name are available the name is shown first. To view
the number:
#
Press the hash key. Use this key to switch between the
number and name display.
Y
Transferring a number from the call list to the phonebook
q
q
~
~
Y
Open the call list.
Select the entry and open the context menu with [.
Select SAVE NUMBER and confirm with [.
Change the number (if required) and confirm with [.
Enter or edit the name and confirm with [.
Deleting an entry / Deleting all entries
q
q
[
Open the call list.
Select an entry and open the context menu with [.
Select DELETE ENTRY to delete the selected entry or
DELETE ALL to delete all entries and confirm with [.
Press the control key to confirm the action.
You can save 10 numbers for speed dial on the number keys (each with
max. 32 digits).
Storing a speed dial number
You can enter the number in idle mode or when the handset is lifted.
K J Press the set key, press the speed dial key and press [.
Q ... O Choose a speed dial key and press [.
If the key is already allocated, the content is displayed.
either ...
~
Enter the phone number for speed dial.
... or
Take over the phone number from the call or redial list
t / I Open the call/redial list.
q
Select the desired entry in the list and press [.
Storing the speed dial entry
K
Press the set key or [.
Notes
When storing speed dial numbers, please note the following:
u * and # are saved regardless of the set dialling mode but are
only dialled with tone dialling mode ( page 11).
u If the number entered is longer than 32 digits, only the first 32 digits
are stored.
A single speed dial number cannot be deleted but only overwritten.
£
Adjusting the telephone
To adjust the settings of your telephone you use the K set key. You
can make settings in idle mode and when the handset is lifted.
Changing the language
You can change the language for display messages. There are six languages to choose from.
K
Activate setting mode.
5 L Press the key code for setting the language.
Press the key for the desired language:
Q English
3 Spanish
K
8
2
German
French
4 Italian
5 Polish
Save your settings and exit the setting mode.
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Setting the date and time
You can adjust the current date manually and change the format of the
display. The time is updated by incoming calls with telephone number
displays. You can adjust this setting if necessary ( page 12).
2
£
Setting the date and time
K 3 Activate setting mode for the date and time. The date and
time display becomes editable.
~
Enter a 4-digit date and a 4-digit time. Use the q control
key to move one position forwards/backwards.
K
Save your settings and exit the setting mode.
The date setting format is according to the one currently set. The time
setting format is always 24-hour, regardless of the set time format.
Setting the date format
K
5
K
Save your settings and exit the setting mode.
The mute function is activated according to these settings using the
mute key during a call ( page 7).
£
Setting the ringer
¤
¤
¤
The following optional settings are available:
Melody and volume
VIP melody
Switching the ringer off
Setting the ring tone and volume
Activate setting mode.
Press the key code for setting the date format.
Press the key code for the desired date format:
Q for MM/DD e.g. 12/31 for 31 December
You can set the ring tone and volume or switch the ringer off. There are
10 different ring tones available and the volume can be adjusted to 5 levels (0=silent).
Note
The ring tones are played over the speaker if you lift the handset
before commencing with the settings.
for DD/MM e.g. 31/12
K
2 for MM.DD e.g. 12.31
3 for DD.MM e.g. 31.12
£
You can also change both settings directly using the keys while the telephone is ringing ( page 7).
Save your settings and exit the setting mode.
Setting the time format
Changing the ringer volume
K 5 Activate setting mode for the ringer volume. The currently
set ringer is played.
D / E Increase or decrease the volume for the ringer.
K
Activate setting mode.
5 Q Press the key code for setting the time format.
Press the key for the desired time format:
12-hour format
K
or
2 24-hour format
Q ... 4 Select the desired value using the number keys.
K
Press the set key or [ to save your settings and exit the
Save your settings and exit the setting mode.
setting mode.
Setting the handset volume
£
The handset volume can be set using the setting mode or changed
directly during the telephone conversation using the keys ( page 7).
There are three adjustable levels.
K O Activate setting mode for the handset volume.
Press the key code for the desired volume:
low
2 medium 3 high
K
Microphone, receiver and melody off.
The telephone is completely muted.
Microphone off, receiver on, melody off.
You are still able to hear the person on the end of
the line, however they cannot hear you.
Changing the ring tone
K M Activate setting mode for the ring tone. If you lift the handset, you will hear the currently set ring tone.
Q ... O Select the required ring tone.
K
Press the set key or [ to save your settings and exit the
setting mode.
Note
The ring tone can only sound perfectly when the ring pulse arriving
from the telephone network is long enough. The length of the pulses
may differ from network to network. It is therefore possible that some
ring tones for selection may sound clipped. If this is the case please
select another ring tone.
Save your settings and exit the setting mode.
Setting the mute behaviour and music on hold
You can define the behaviour of the microphone and the handset when
the telephone is muted and whether or not a melody is played.
K
Activate setting mode.
O # Press the key code for mute setting.
Press the key code for the desired behaviour:
Q Microphone and receiver off, melody on.
While in mute mode, the person on the other end of
the line hears a melody.
Setting the VIP ring tone and volume
£
You can set one of the ringers as a VIP ring tone. If you have assigned VIP
status to a number from the phonebook ( page 7), an incoming call
from this number will be indicated by the VIP ring tone.
en fr fa ar
9
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
K5*
Emergency calls
Changing the VIP ringer volume
D /E
Activate setting mode for the VIP ringer volume. If you lift
the handset, you will hear the VIP ringer at the currently
set volume.
Increase or decrease the volume for the ringer.
setting mode.
Saving the emergency number
KN3
KM*
Changing the VIP ring tone
Activate setting mode for the emergency number. If an
emergency number is already set, it is displayed. Hold
down the u key to clear the number.
Q ... O / * / # / H / I
Enter the emergency number.
K
Press the set key or [ to save your settings and exit the
setting mode.
Activate setting mode for the VIP ring tone. If you lift the
handset, you will hear the currently set VIP ring tone.
Select the required ring tone.
Press the set key or [ to save your settings and exit the
setting mode.
Switching the ringer off
If you do not wish to be disturbed, you can switch off the ringer. The following three settings are available: all tones off, VIP only on, all tones on.
*
Hold down the key to switch all ring tones off.
K*K
or
Press the key sequence to switch the ringer off for normal
callers but leave it on for VIP contacts.
Pressing the key sequence again will switch off the ringer
for all callers.
Once the ring tone has been switched off, the x symbol appears in the
display.
Switching the ringer back on
*
Hold down the key to switch all ring tones on.
Activating the key lock
When the telephone is on standby, press and hold down
the lock key.
Once the key lock has been switched on, the i symbol and the KEYS
LOCKED message appear in the display. If the handset is lifted, the key
lock is indicated by
.
Hold down the lock key.
Activating direct calling
KN2
Activate setting mode for direct calling.
Q ... O / * / # / H / I
K
X
K
You can secure your telephone against unauthorised access by using the
key lock. When the key lock is activated, all keys are locked, with the
exception of the # key and the stored emergency number (see
below).
#
When direct calling is activated, the stored number (max. 32 digits) is
dialled by pressing any key (except for the key sequence
K N 2).
Enter the direct calling number.
Press the set key or [ to activate direct calling and exit
the setting mode.
KN2
Locking the telephone
Deactivating the key lock
Direct calling (baby call)
Deactivating direct calling
Security settings
#
Selecting an emergency number with activated key lock
c Lift the handset.
is displayed.
~
Enter the emergency number.
Q ... 4 Select the desired value using the number keys.
K
Press the set key or [ to save your settings and exit the
or
Q ... O
K
There are two emergency numbers stored in the telephone by default
(110, 112). You can store an additional emergency number with up to 32
digits. These emergency numbers can also be selected when the key
lock is switched on.
Activate setting mode for direct calling.
Hold down the u key to clear the direct call number.
Press the set key or [ to deactivate direct calling and exit
the setting mode.
Blocking numbers
You can block phone calls to specific dialling codes (e.g. chargeable
codes), max. 3 numbers with 5 digits each.
K 2 Activate setting mode for blocking numbers. If a dialling
code is already set, it is displayed. Hold down the u key
to clear the entry.
Q ... O Enter the dialling code to be blocked (max. 5 digits).
To edit the next dialling code:
v
Confirm with [ and continue.
To save the settings:
K
Save your settings and exit the setting mode.
Note: The names of persons, whose numbers are stored in the phonebook with the area code defined here, are no longer displayed. Change
the appropriate phonebook entries, where necessary.
10
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Network services
Changing the dialling mode/flash time
Public telephone systemsoffer you – in some cases only on request – a
range of helpful, additional services (e. g. call forwarding, callback when
busy, withheld number, etc.). These services can be selected using specified key combinations, of which your network provider will notify you.
Caller display (CLIP)
If the caller display service is activated, an incoming call is shown on the
display with the number and saved in the call list. Requirement: The
network provider supports the following service features and the number transfer is not withheld by the caller:
u CLI (Calling Line Identification): The caller's number is transferred.
u CLIP (Calling Line Identification Presentation): The caller's number is
displayed.
You can transfer this number to the phonebook and edit it ( page 7).
If you have saved the local dialling code ( page 11), a call with the
same dialling code is automatically only displayed as the number without the dialling code.
£
£
Recall key
In public telephone systems the recall key (flash) is required for the use
of various additional services; e.g. for "callback when busy".
If necessary, the flash time on your telephone must be adjusted to the
requirements of the telephone system ( page 11).
£
Setting up a dialling code
If necessary you can change the default setting for the area code for your
connection which is saved in the telephone. The number saved here is
then used to display only the number of the person calling without the
area code in the call lists, provided they have the same area code.
You can enter two area codes.
K 4 Activate setting mode for the area code. The default number is displayed.
Q ... O / * / #
Enter the new area code (max. 5 digits).
To edit the second area code:
v
Confirm with [ and continue.
To save the settings:
K
Save your settings and exit the setting mode.
Operation on a PABX
Special functions/Recall key
During an external call, you can make an enquiry or forward the call. To
do this, press the recall key H. The subsequent procedure depends
on your PABX. To set the recall key, the telephone's flash time must be set
consistently with your PABX. Please refer to the operating instructions
for your PABX.
The telephone supports the following dialling modes:
u Tone dialling
u Pulse dialling
Depending on your PABX, you may need to change your phone's dialling
mode or the flash time. (Default setting: Tone dialling)
Changing the dialling mode
K # Activate setting mode for the dialling mode.
Press the key code for the dialling mode:
Tone dialling
2
K
Pulse dialling
Save your settings and exit the setting mode.
Temporary switch to tone dialling in "Pulse" position
To use functions that require tone dialling (e.g. remote control of
answering machine), you can set the telephone to tone dialling for the
duration of the call.
After the connection is established:
*
Press the star key.
After the connection is terminated, the setting reverts to pulse dialling.
Changing the flash interval
You can change the flash interval if the dialling mode is set to tone dialling (see above) (default setting 90 ms).
K
Activate setting mode.
O 5 Press the key code for setting the flash interval.
Q ... 4 Select the flash interval (ms):
0 = 90
1 = 120
2 = 270
3 = 375
4 = 600
K
Press the set key to save your settings and exit the setting
mode.
Setting dialling prefixes
If your phone is connected to a PABX, you may have to use a dialling prefix to make external calls. You can save up to three prefixes in your telephone.
If a dialling prefix is recognised during dialling, a dialling pause will automatically be applied. You can adjust the time of the dialling pause if necessary ( page 12).
K Q Activate setting mode for the dialling prefix.
The current setting of the first dialling prefix is displayed.
Q ... O, *, #, H
Enter the dialling prefix (1 to 3 digits) and confirm with [.
Enter the next prefix and confirm with [.
u
Hold down the control key X to delete the current dialling prefix.
K
Save your settings and exit the setting mode.
en fr fa ar
£
11
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / telephony.fm / 22.03.2016
Other settings
Standard characters
£
In addition to the options described in section Adjusting the telephone ( page 8), you can perform further settings in setting mode
(e.g. reset the factory settings). These are summarised in the following
table.
Default settings are displayed in bold. If there is no bold value for a setting, the presetting is country-dependent.
K
Press the set key and 1.
~
Enter the key sequence for the setting.
v
Confirm with [ to save the setting and stay in setting
mode.
The following characters can be entered using the keypad:
Key
*)
2
3
4
5
L
M
N
O
Q
*
#
or
K
Press the set key to save the setting and exit the setting
mode.
Key
sequence
02
0
1
2
25
0
53
0
1
2
70
0
1
83
0
1
2
91
0
1
0
1
2
0
1
98
#0
#1
#2
0
1
0
1
Value
Description
1s
Sets the length of the pause that
3s
can be inserted with the pause key.
6s
Restores all settings to default (factory settings).
Deactivate
Flash interval for the LED (hands500 ms/500 ms
free key) on incoming call.
30 ms/70 ms
Deactivate
Use only the FSK checksum for verActivate
ifying the received CLIP information (FSK = Frequency Shift Keying).
Deactivate
Withholds the first ringer. With this
Activate
setting you can determine whether
Automatic
an incoming call is coming from a
VIP number, and select a VIP ring
tone instead of the normal ring
tone.
1.5 : 1
Sets the pulse ratio for pulse dial2:1
ling.
23 - 54 Hz
Defines the frequency for call
15 - 75 Hz
detection.
Frequency not evaluated
Ringer
Start signal for CLIP recognition.
AC detection
If CLIP does not function with the
default setting 0, select setting "1".
Deactivate
Updates the time automatically
Activate
according to CLIP information.
Deactivate
Updates CLIP time according to sysActivate
tem time if the CLIP information is
not valid.
1x
2x
1
3x
_
5x
>
A
B
C
2
D
E
F
3
G
H
I
4
J
K
L
5
M
N
O
6
P
Q
R
S
T
U
V
8
W
X
Y
Z
9
0
-
/
\
# **)
6x
7
+
*
# **)
*) Space **) Shown as
12
4x
<
in the display.
en fr fa ar
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / appendix.fm / 22.03.2016
Disposal
Appendix
Care
Wipe the unit with a damp cloth or an antistatic cloth. Do not use
solvents or microfibre cloths. Never use a dry cloth; this can cause static.
Contact with liquid !
If the device comes into contact with liquid:
1 Allow the liquid to drain from the device.
2 Pat all parts dry. Place the device (the keypad facing down) in a dry,
warm place for at least 72 hours (not in a microwave, oven etc.).
3 Do not switch on the device again until it is completely dry.
When it has fully dried out, you will normally be able to use it again.
In rare cases, contact with chemical substances can cause changes to the
telephone's exterior. Due to the wide variety of chemical products available on the market, it was not possible to test all substances.
Questions and answers
You lift the handset, but don't hear the free tone:
Lift the handset for 5 seconds, put it back in the cradle and lift it again.
You lift the handset but you hear no dialling tone:
Is the connecting lead correctly plugged into the telephone and the
telephone socket?
The dialling tone is audible but the telephone will not dial:
The connection is OK. Is the dialling mode set correctly?
The other party cannot hear you:
Mute activated?
Regular pulse noises can be heard during a call:
The connection is receiving metering pulses from the exchange, which
the telephone cannot interpret. Contact your network operator.
All electrical and electronic equipment must be disposed of separately
from general household waste using the sites designated by local
authorities.
If a product displays this symbol of a crossed-out rubbish bin,
the product is subject to European Directive 2012/19/EU.
The appropriate disposal and separate collection of used
equipment serve to prevent potential harm to the environment and to health. They are a precondition for the re-use and recycling
of used electrical and electronic equipment.
For further information on disposing of your used equipment, please
contact your local authority or your refuse collection service.
Contacts
If you should encounter any problems when operating the telephone
connected to a communication system with analogue network access,
please contact the network operator responsible or your dealer.
Authorisation
(not for SEA and India)
This device is intended for analogue phone lines outside the European
Economic Area (with the exception of Switzerland) depending on
national type approval.
Country-specific requirements have been taken into consideration.
We, Gigaset Communications GmbH, declare that this device meets the
essential requirements and other relevant regulations laid down in
Directive 2014/30/EU and 2014/35/EU.
A copy of the Declaration of Conformity is available at this Internet
address:
www.gigaset.com/docs
Environment
Our environmental statement
We at Gigaset Communications GmbH are aware of our social responsibility. That is why we actively take steps to create a better world. In all
areas of our business – from product planning and production to sales
and waste of disposal – following our environmental conscience in everything we do is of utmost importance to us.
Learn more about our earth-friendly products and processes online at
www.gigaset.com.
Environmental management system
Gigaset Communications GmbH is certified pursuant to the
international standards ISO 14001 and ISO 9001.
ISO 14001 (Environment): Certified since September 2007
by TÜV SÜD Management Service GmbH.
ISO 9001 (Quality): Certified since 17/02/1994 by TÜV SÜD
Management Service GmbH.
en fr fa ar
13
1110-01
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / DA610SIX.fm / 22.03.2016
Index
M
A
Music on hold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute behaviour. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mute key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Authorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
9
7
9
1
N
B
Baby call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Blocking numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Network services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
O
C
Open listening . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Call list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dialling from . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Saving numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Caller display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Changing the dialling mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CLI, CLIP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contact with liquid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Control key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
P
D
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Date format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Dialling code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dialling prefixes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Dialling, telephone number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Direct calling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Display symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Phonebook
Dialling from. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Saving numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
R
Recall key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1, 11
Redial list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Redial/pause key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Restore factory settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Ringer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ringer settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ringer volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
S
Flash time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Function code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving
Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the volume
Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speaker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed dial key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Speed dial number
Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Star key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H
T
Handset volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Hands-free . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Hands-free key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Hash key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Telephone
Changing the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Locking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting the date/time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Text entry. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Time format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
E
Emergency calls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Entering characters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5, 12
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
F
K
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1, 10
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
L
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Last number redial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
14
4
7
1
7
7
1
6
8
1
V
VIP mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
VIP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Volume keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
All rights reserved. Rights of modification reserved.
1110-01
en fr fa ar
Gigaset DA610 / en / A30350-M212-A601-5-UZ19 / Cover_back.fm / 22.03.2016
Issued by
Gigaset Communications GmbH
Frankenstrasse 2a, D-46395 Bocholt
© Gigaset Communications GmbH 2016
Subject to availability.
All rights reserved. Rights of modification reserved.
www.gigaset.com
A30350-M212-A601-5-UZ19
16
en fr fa ar
1110-01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising