Planar | UR8451-LX-Touch | User manual | Planar UR7551 User Manual

Planar UR7551 User Manual
Planar UltraRes Series
User Manual
Copyright © 16 Jun 2016 by Planar Systems, Inc. All rights reserved.
Contents of this publication may not be reproduced in any form without permission of Planar
Systems, Inc.
Trademark Credits
Windows™ is a trademark of Microsoft Corp.
All other companies are trademarks or registered trademarks of their respective companies.
Disclaimer
The information contained in this document is subject to change without notice. Planar
Systems, Inc. makes no warranty of any kind with regard to this material. While every
precaution has been taken in the preparation of this manual, the Company shall not be liable
for errors or omissions contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this material.
Warranty and Service Plans
Planar warranty and service plans will help you maximize your investment by providing great
support, display uptime, and performance optimization. From post-sale technical support to
a full suite of depot services, our services are performed by trained Planar employees. When
you purchase a Planar product, you get more than a display, you get the service and support
you need to maximize your investment. To find the latest warranty and service information
regarding your Planar product, please visit http://www.planar.com/support
RoHS Compliance Statement
The Planar UltraRes Series is fully RoHS compliant.
Part Number: 020-1301-00C
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Recommended Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Mounting with a VESA Mount. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Cleaning the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Unpacking and Checking Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Accessory Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Planar UltraRes Series - Standard Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Installing the Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the Planar Profile Mounting System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Installing OPS Expansion (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Supported Graphics Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
OSD Keypad. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Remote Control Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Display in Portrait Mode (UR8451-MX and UR9851 Only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Display in Flat or Tilted Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
IR Command Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Turning the Display On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Planar UltraRes Series User Manual
i
Table of Contents
Turning the Display Off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Selecting Layouts and Input Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Navigating Through the Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Using the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Touchscreen MultiTouch Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Touchscreen (PQLabs) MultiTouch Platform Content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69
Uninstalling the MultiTouch Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Planar UltraRes Remote Monitoring Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Remote Monitoring Home. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Remote Monitoring System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Remote Monitoring Inputs and Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Remote Monitoring Audio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Remote Monitoring Presets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Remote Monitoring Panel Brightness and Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Remote Monitoring Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Remote Monitoring System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
Remote Monitoring Access Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
External Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Signal Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80
Color Subsampling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
UR7551 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
UR7551 Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88
ii
Planar UltraRes Series User Manual
UR8451 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
UR8451 Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
UR9851 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
UR9851 Touch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Troubleshooting During Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Error Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Symptoms, Possible Causes and Solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Accessing Planar’s Technical Support Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Planar UltraRes Series User Manual
iii
iv
Planar UltraRes Series User Manual
Introduction
The Planar® UltraRes™ Series displays raise the bar for commercial 4K. Offered in 75”,
84”, and 98”, these Ultra HD displays produce resolution and picture quality never
before seen in large format LCD displays. Designed specifically for resolution-rich
commercial applications, Planar UltraRes Series displays offer the image quality,
connectivity, industrial design and configuration options required in high profile
offices, leading control rooms, collaboration rooms and digital branding installations.
Features of the Planar UltraRes Series displays include:
• Best-in-class image and color quality for native and upscaled content
• Cutting edge video performance supporting up to 4K @ 60Hz with
DisplayPort 1.2 and HDMI 2.0
• Planar® MediaPlex™ Plus Processing for advanced multi-source viewing and
image adjustment control
• Next generation 4K compatibility
• Advanced design for function and style
• Fully integrated multi-touch models available
• Fanless, whisper-quiet
Planar UltraRes Series User Manual
1
Safety Information
Safety Information
Before using the Planar UltraRes Series, please read this manual thoroughly to help
protect against damage to property, and to ensure personal safety.
• Be sure to observe the following instructions.
• For your safety, be sure to observe ALL the warnings detailed in this manual.
• For installation or adjustment, please follow this manual’s instructions, and refer
all servicing to qualified service personnel.
Safety Precautions
• If water is spilled or objects are dropped inside the display, remove the
power plug from the outlet immediately. Failure to do so may result in fire or
electrical shock. Contact your dealer for inspection.
• If the display is dropped or the chassis is damaged, remove the power plug
from the outlet immediately. Failure to do so may result in fire or electrical
shock. Contact your dealer for inspection.
WARNING! Wall mounts must be secure.
• If the display is hung on a wall, the wall must be strong enough to hold it.
Simply mounting it to wallboard or wall paneling won’t be adequate or safe.
Caution: The screen could be damaged by heavy pressure.
• Slight pressure on the LCD will cause distortion of the image. Heavier
pressure will cause permanent damage. Displays should be mounted where
viewers cannot touch the screen or insert small objects in the openings that will
create hazards by contacting bare conductive parts.
Caution: The front polarizer is soft and subject to scratches from sharp objects.
• The polarizer is a thin sheet of film laminated to the outside layer of glass
on the LCD screen. Take care when handling items near the screen.
• If the power cord or plug is damaged or becomes hot, turn off the main
power switch of the display. Make sure the power plug has cooled down
and remove the power plug from the outlet. If the display is still used in this
condition, it may cause a fire or an electrical shock. Contact your dealer for a
replacement.
2
Planar UltraRes Series User Manual
Important Safety Instructions
Important Safety Instructions
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings.
4 Follow all instructions.
5 Do not use the display near water.
6 Clean the LCD screens with an LCD screen cleaner or LCD wipes.
7 Do not install near any heat sources such as radiators, heat registers, stoves or
other apparatus (including amplifiers) that produce heat.
8 Do not defeat the safety purpose of the polarized or grounding type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong is provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for the replacement of the obsolete outlet.
9 Protect the power cord from being walked on or pinched, particularly at plugs,
convenience receptacles and the point where they exit from any of the displays.
10 Only use the attachments/accessories specified by the manufacturer.
11 Unplug all displays during lightning storms or when unused for long periods of
time.
12 You must follow all National Electrical Code regulations. In addition, be aware of
local codes and ordinances when installing your system.
13 Refer all servicing to qualified service personnel. Servicing is required when any
of the displays have been damaged in any way. For example, if the AC power cord
or plug is damaged, liquid has been spilled or objects have fallen into a display,
the displays have been exposed to rain or moisture, do not operate normally or
have been dropped.
14 Keep the packing material in case the equipment should ever need to be
shipped.
Planar UltraRes Series User Manual
3
Recommended Usage
Recommended Usage
In order to get the most out of your LCD, use the following recommended guidelines
to optimize the display.
Burn-In Versus Temporary Image Retention
Burn-in causes the screen to retain an image essentially forever, with little or no way
to correct the problem. Under normal use, an LCD will not experience burn-in, as
plasma displays do, nor will it retain images in any way.
Normal use of an LCD is defined as displaying continuously changing video patterns
or images. However, LCDs can experience temporary image retention when
recommended usage guidelines are not followed.
What is Temporary Image Retention?
Temporary image retention (TIR) can occur when a static image is displayed
continuously for extended periods of time (12 hours or longer). An electrical charge
differential may build up between the electrodes of the liquid crystal, which causes a
negative-color video image (color-inverted and brightness-inverted version of the
previous image) to be retained when a new image is displayed. This behavior is true
for any LCD device from any LCD manufacturer.
TIR is not covered under warranty. See standard warranty terms and conditions for
details. Here are some guidelines to help you avoid TIR:
• Use the LCD to show a screen saver, moving images or still pictures that change
regularly. When using high-contrast images, reposition the images frequently.
• Turn off the LCD when it is not in use. To use your source computer’s Power
Options Properties, set up your computer to turn off the display when not in
use.
Caution: For optimal performance, we suggest turning off the power on the 84” MX and 98”
for 4 hours per day and 12 hours per day on the 75” and 84” LX models.
4
Planar UltraRes Series User Manual
European Union Disposal Information
European Union Disposal Information
Français
English
■ Disposal of old Electrical & Electronic Equipment (Applicable throughout
the European Union and other European countries with separate collection
programs)
■ Mise au rebut des équipements électriques et électroniques usagés
(Valable dans l’ensemble de l’Union Européenne ainsi que dans les pays
européens disposant de programmes distincts de collecte des déchets)
Deutsch
■ Entsorgung von elektrischen & elektronischen Altgeräten (geltend für die
europäische Gemeinschaft und andere europäische Länder mit separaten
Sammelprogrammen)
This symbol found on your product or on its packaging, indicates that
this product should not be treated as household waste when you wish to
dispose of it. Instead, it should be handed over to an applicable collection
point for the recycling of electrical and electronic equipment. By ensuring
this product is disposed of correctly, you will help prevent potential
negative consequences to the environment and human health, which
could otherwise be caused by inappropriate disposal of this product. The
recycling of materials will help to conserve natural resources.
Ce symbole appliqué sur votre produit ou sur son emballage indique
que ce produit ne doit pas être traité comme un déchet ménager lorsque
vous voulez le mettre au rebut. Il doit au contraire être remis à un site
de collecte agréé pour le recyclage des équipements électriques et
électroniques. En veillant à ce que ce produit soit mis au rebut de façon
adéquate, vous contribuerez à prévenir les conséquences potentiellement
négatives sur l’environnement et sur la santé humaine qui risqueraient
de se produire en cas de mise au rebut inappropriée de ce produit. Le
recyclage des matériaux contribuera également à économiser les ressources naturelles.
Dieses Symbol, zu finden auf Ihrem Produkt oder dessen Verpackung,
macht Sie darauf aufmerksam, dass dieses Produkt bei der Entsorgung
nicht als Hausmüll behandelt werden darf. Statt dessen sollte es an eine
Sammelstelle zum Recycling von elektrischen und elektronischen Altgeräten gegeben werden. Helfen Sie mit, potenziell schädliche Einflüsse
auf Umwelt und Gesundheit, die durch eine unsachgemäße Entsorgung
dieses Produktes entstehen können, zu vermeiden und entsorgen Sie
dieses Produkt ordnungsgemäß. Recycling hilft, natürliche Rohstoffe
einzusparen.
This symbol is only valid in the European Union.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the correct method of disposal.
Ce symbole n’est valable que dans l’Union Européenne.
Si vous souhaitez mettre ce produit au rebut, veuillez
prendre contact avec les autorités locales ou avec votre
revendeur et renseignez-vous sur la méthode de mise
au rebut correcte.
Dieses Symbol ist nur innerhalb der europäischen
Gemeinschaft gültig.
Wenn Sie dieses Produkt entsorgen möchten, wenden
Sie sich bitte an Ihre örtliche Behörde und fragen Sie
nach der ordnungsgemäßen Entsorgungsmethode.
Italiano
Español
■ Deshecho de equipos eléctricos y electrónicos (aplicable a la Unión Europea y a otros países europeos con programas de reciclaje independientes)
La presencia de este símbolo en el propio producto o en su material de
embalaje, indica que no se debe tratar como residuo doméstico cuando
desee deshacerse de él. En su lugar, debe entregarlo en el punto limpio
correspondiente de reciclaje de equipos eléctricos y electrónicos. Asegurándose de que este producto se desecha de forma correcta, ayudará
a evitar posibles consecuencias negativas para la conservación del
medioambiente y la salud humana, consecuencias que podrían darse si
se deshace del producto de forma inadecuada. El reciclado de materiales
ayuda a conservar los recursos naturales.
Este símbolo solamente es válido en la Unión
Europea.
Si desea deshacerse de este producto, póngase
en contacto con las autoridades locales o con su
distribuidor y pida información sobre el método de
disposición adecuado.
■ Smaltimento delle attrezzature elettriche ed elettroniche usate (applicabile
in tutta la Comunità Europea ed altri Paesi Europei che applicano
programmi di raccolta differenziata)
Il simbolo trovato sul prodotto, o sulla sua confezione, indica che il
prodotto non può essere trattato come i domestici quando è il momento
di smaltirlo. Al contrario, deve essere consegnato ad un centro di raccolta
specializzato nel riciclaggio di attrezzature elettriche ed elettroniche. Assicurando che il corretto smaltimento di questo prodotto, si aiuterà a prevenire potenziali conseguenze negative sull’ambiente e sulla salute umana,
che possono essere provocate da uno scorretto smaltimento di questa
attrezzatura. I materiali riciclati aiuteranno a conservare le risorse naturali.
Questo simbolo è valido solo nell’Unione Europea.
Per smaltire questo prodotto, mettersi in contatto con
le autorità locali – o con il rivenditore – e chiedere
informazioni sul corretto metodo di smaltimento.
Polski
Português
■ Eliminação de equipamentos eléctricos e electrónicos usados (aplicável
na União Europeia e noutros países europeus com programas próprios de
recolha destes equipamentos)
Este símbolo, colocado no produto ou na respectiva embalagem, indica
que o produto não deve ser tratado como lixo doméstico aquando da sua
eliminação. Em vez disso, deve ser entregue num ponto de recolha de equipamentos eléctricos e electrónicos para posterior reciclagem. Ao garantir
a correcta eliminação deste produto, estará a evitar consequências potencialmente negativas tanto para o ambiente como para a saúde humana. A
reciclagem de materiais ajuda a preservar os recursos naturais.
Este símbolo apenas é válido na União Europeia.
Se quiser eliminar este produto, contacte as entidades locais ou o seu fornecedor para ficar a saber
qual o método de eliminação correcto.
■ Usuwanie zużytego sprzętu elektrycznego i elektronicznego (Dotyczy
krajów Unii Europejskiej i innych krajów europejskich z oddzielnymi
programami zbiórki odpadów)
Obecność tego symbolu na produkcie lub na opakowaniu z produktem
oznacza, że tego produktu nie można wyrzucać razem z odpadkami
domowymi. Należy go przekazać do punktu zbiórki w celu poddania
recyklingowi podzespołów elektrycznych i elektronicznych. Usunięcie tego
produktu w prawidłowy sposób, pomoże w zabezpieczeniu przed negatywnym wpływem odpadów na środowisko i zdrowie ludzi, powodowanym
przez niewłaściwe usuwanie produktu. Przetwarzanie materiałów pomaga
w zachowaniu zasobów naturalnych.
Ten symbol obowiązuje wyłącznie w krajach Unii
Europejskiej.
Informacje dotyczące prawidłowej metody usunięcia
tego produktu, można uzyskać u władz lokalnych lub
u dostawcy.
Suomi
Svenska
■ Avfall av förbrukad elektrisk och elektronisk utrustning (Tillämpbart i
hela Europeiska unionen och andra europeiska länder med separata
samlingsprogram)
Den här symbolen som finns på din product eller på dess förpackning
påvisar att produkten inte ska behandlas som hushållsavfall när du vill
slänga bort den. Istället ska den lämnas över till en lämplig uppsamlingspunkt för återvinning av elektriska och elektroniska utrustningar. Genom att
tillförsäkra att den här produkten återvinns på ett riktigt sätt hjälper du till
med att förhindra möjliga negative konsekvenser för miljön och mänsklig
hälsa. Det kan annars orsakas på grund av olämplig sophantering av den
här produkten. Återvinning av material kommer att hjälpa till att bevara
naturtillgångar.
Den här symbolen är endast giltig inom den
Europeiska unionen.
Om du vill slänga bort den här produkten ska du
kontakta lokala myndigheter eller återförsäljar, och
fråga efter lämplig avfallsmetod.
■ Vanhojen sähkö- ja elektroniikkalaitteiden hävittäminen (Soveltuva kaikkialla Euroopan unionin alueella, sekä muissa Euroopan maissa, joilla on
erilliset keräysohjelmat)
Jos tuotteessa tai sen pakkauksessa on tämä symboli, sitä ei pidä
hävitettäessä käsitellä tavallisena kotitalousjätteenä, vaan se kuuluu toimittaa sähkö- ja elektroniikkalaitteiden kierrätyspisteeseen. Varmistamalla,
että tämä tuote hävitetään asiaankuuluvalla tavalla autat estämään mahdollisia ympäristölle ja ihmisille koituvia negatiivisia seuraamuksia, joita
sen vääränlainen hävittäminen voi aiheuttaa. Materiaalien kierrättäminen
auttaa säilyttämään luonnonvaroja.
Tämä symboli on voimassa ainoastaan Euroopan
unionin alueella.
Jos haluat hävittää tämän tuotteen, ota yhteyttä
paikallisiin viranomaisiin tai jälleenmyyjään ja tiedustele
asiaankuuluvia hävittämistoimenpiteitä.
Planar UltraRes Series User Manual
Nederlands
■ Verwijderen van oude elektrische en elektronische apparatuur (toepasselijk in de volledige Europese Unie en andere Europese landen met
afzonderlijke programma’s voor afvalverzameling)
Dit symbool dat op het product of zijn verpakking is aangebracht, geeft aan
dat dit product niet mag worden behandeld als huishoudelijk afval als u het
wilt wegwerpen. U moet het afgeven bij een specifiek verzamelpunt voor
de recyclage van elektrische en elektronische apparatuur. Door te garanderen dat u dit product op de correcte manier wegwerpt, helpt u potentiële
negatieve gevolgen voor het milieu en de menselijke gezondheid, die
zouden kunnen worden veroorzaakt door een onrechtmatig wegwerpen
van het product, te voorkomen. De recyclage van materialen helpt het
behoud van natuurlijke bronnen.
Dit symbool is alleen geldig in de Europese Unie.
Als u dit product wenst weg te gooien, dient u contact op
te nemen met uw lokale instanties voor details over de
gepaste methode voor afvalverwijdering.
Waste Electrical and Electronic Equipment (WEEE) Directive
In the European Union, this label indicates that this product
should not be disposed of with household waste. It should
be deposited at an appropriate facility to enable recovery
and recycling. EEE complies with Directive ‘Regulation on
the Restriction of the Use of Certain Hazardous Substances
in Electrical and Electronic Equipment’
Waste Electrical and Electronic Equipment
(WEEE) Directive In the European Union, this
label indicates that this product should not be
disposed of with household waste. It should be
deposited at an appropriate facility to enable
recovery and recycling. EEE complies with
Directive ‘Regulation on the Restriction of the
Use of Certain Hazardous Substances in
Electrical and Electronic Equipment’
Waste Electrical and Electronic Equipment (WEEE)
Yönergeleri Avrupa Birliği'nde bu etiket, ürünün ev
elektroniği aletleri atıkları ile imha edilemeyeceğini gösterir.
Kurtarmak ve geri dönüşümünü sağlamak için uygun
şartlarda saklanması gerekir. EEE Yönetmeliğine Uygundur
Ve Elektronik Eşyalarda Bazi Zararli Maddelerin Kullaniminin
Sinirlandirilmasina Dair Yönetmelik.
Waste Electrical and Electronic Equipment
(WEEE) Yönergeleri Avrupa Birliği'nde bu etiket,
ürünün ev elektroniği aletleri atıkları ile imha
edilemeyeceğini gösterir. Kurtarmak ve geri
dönüşümünü sağlamak için uygun şartlarda
saklanması gerekir. EEE Yönetmeliğine
Uygundur Ve Elektronik Eşyalarda Bazi Zararli
Maddelerin Kullaniminin Sinirlandirilmasina
Dair Yönetmelik.
5
Normal Usage Guidelines
Normal Usage Guidelines
Normal use of the LCD is defined as operating in the open air to prevent heat
buildup, and without direct or indirect heat sources such as lighting fixtures, heating
ducts, or direct sunlight that can cause the displays to experience high operating
temperatures. For all displays, do not block fans or ventilation openings. If the LCD
display will be installed in a recessed area with an LCD surround or enclosure, ensure
adequate openings are applied for proper air flow and ventilation.
It is up to the installer to ensure that display placement is changed, thermal shielding
is provided and/or additional ventilation is provided to keep the display within its
nominal operating parameters. Maximum ambient operating temperatures for the
Planar UltraRes Series are:
• 75” Planar UltraRes models: 0-40°C at up to 1500 meters and 0-35°C at up to
3000 meters
• 84” and 98” Planar UltraRes models: 0-35°C at up to 1500 meters and 0-30°C at
up to 3000 meters
Cooling Requirements
For optimal performance, active cooling by the installer should be planned for when
the ambient temperature anywhere in the wall is predicted to be above the specified
ambient temperature for the display.
Mounting with a VESA Mount
The Planar UltraRes Series can be mounted with the Planar Profile Mounting System
(see page 12) or with a VESA mount, available from Planar or other manufacturers.
If you purchased a VESA mount, you should have a received a separate box with
mounting supplies and an Installation manual. Follow these instructions carefully.
Keep in mind the following general installation guidelines:
• Screw length is crucial and will vary depending on the type of mount you use.
Total screw length will include the penetration length plus the length required
by the type of VESA mount in use.
Caution: Shorter screws will result in insufficient mounting strength and longer screws
could puncture parts inside the display.
• Prior to installation, make sure you know where all of the mounting points are
located.
• Follow all safety precautions outlined in the VESA Installation manual.
• Verify the parts received with the list shown in the VESA Installation manual.
6
Planar UltraRes Series User Manual
Cleaning the Display
Cleaning the Display
If dust has collected on the power plug, remove the plug from the outlet and clean
off the dust. Dust build-up may cause a fire.
Remove the power plug before cleaning. Failure to do so may result in electrical
shock or damage.
Keep the following points in mind when cleaning the surface of the display:
• When the surface of the display becomes dirty, wipe the surface lightly with a
soft clean cloth.
• If the surface requires additional cleaning, use LCD screen cleaner or LCD wipes,
which are available at most electronics stores.
• Do not let cleaner seep into the display, as it may cause electrical shock or
damage.
Planar UltraRes Series User Manual
7
Unpacking and Checking
Accessories
Package Contents
Part
Description
Number
LCD display
One per box.
1
LCD mounts
(optional)
If ordered, this will be inside a
separate box inside the LCD box.
1
Picture
Note: If you do not use Planar’s
mounts, you need to ensure the
mounts that you purchase can
adequately support the display.
Mounting
template
Used to line up where the wall
mounts will be installed. This is
included with Planar’s optional LCD
mounts.
2
Planar UltraRes Series User Manual
8
Accessory Kit
Accessory Kit
Part
Description
Number
Included
AC power cord
Power cord.
1
IR sensor
Used to receive signals from
the remote control.
1
USB drive
Contains the User Manual,
touch drivers and USB-toserial driver.
1
USB cable
Connects to a PC for touch
functionality (touch models
only) and serial commands
(all models).
1
Remote control
Used to control the display.
2 AA batteries are included
but not installed.
1
Carrying Strap
For lifting and carrying the
display using three people
2
Planar®
TouchMark™
Single License
Key Card
Annotation and
whiteboarding software
(touch models only)
1
Planar UltraRes Series User Manual
Picture
9
Planar UltraRes Series - Standard Inputs
Planar UltraRes Series - Standard Inputs
OPS: 4K/60Hz
OPS USB 3.0
OPS USB 2.0
OPS USB 2.0
HDMI 1: HDMI, 4K/60Hz, HDCP 2.2
HDMI 2: HDMI, 4K/60Hz, HDCP 2.2
HDMI 3: HDMI, 4K/30Hz
HDMI 4: HDMI, 4K/30Hz
DP IN: DisplayPort In, 4K/60 Hz
DP OUT: DisplayPort Out
LINE
AUDIO
OUT RS232
SPDIF
AUDIO OUT
10
USB-A
IR
USB-B
LAN
Planar UltraRes Series User Manual
Note: Only one HDCP 2.2 source
can be displayed at a time. If HDMI 1
and HDMI 2 are both being shown
on the display at the same time,
only HDMI 1 will support HDCP 2.2
content.
Installing the Displays
Before installation, keep the following points in mind:
• These displays are heavy. Make sure that you have adequate studs to support
the weight of each display if installing on a wall.
• The Planar UltraRes display must be installed on a flat surface.
• If you ordered the optional wall mounts, use the supplied UltraRes mounting
template for the center point of the display, as well as for top and bottom
bracket installation.
• The wall mounts for a landscape and portrait installation look very similar. The
process to install them is almost exactly the same. The only difference is the way
in which you use the wall mount template. This will be pointed out in the
relevant step.
Planar UltraRes Series User Manual
11
Installing the Planar Profile Mounting System
Installing the Planar Profile Mounting System
Caution: For whatever structure is used to mount the display, be sure that it is sufficiently
engineered to handle the weight of the display. Also be sure to purchase the correct
hardware needed to support the display mounted to that structure.
Caution: If the unit being installed is fitted with a touch input device, it is important that the
touch frame is not used to lift the unit. Also, the unit should never be placed on the touch
frame to support the unit.
1 Find the center point of the display on the wall where you intend to install it.
2 Draw a short (about 1”) horizontal line and then a vertical line to just below the
top edge of the display.
12
Planar UltraRes Series User Manual
Installing the Planar Profile Mounting System
Center notch alignment
3 Use the provided template to determine the center points of the wall mounts.
The “V” notches are labeled “Short Center” and “Long Center”. Use the “Short
Center” hole for a landscape display and the “Long Center” hole for a portrait
display. Use the appropriate “V” notch to align with the horizontal line drawn in
the previous step.
Planar UltraRes Series User Manual
13
Installing the Planar Profile Mounting System
4 In the hole marked “Top” on the template, mark the center of the hole on the wall.
Be sure the vertical line runs through the center of the hole and that the template
is plumb. You may wish to screw the template in place to make the next steps
easier.
Note: If you are installing a landscape display and the template is too long, you can break the
template at the notch below the “L BTM” hole.
5 Let the template hang vertically so it is plumb, as the bottom hole in the template
determines where the bottom mount will be installed.
6 Mark the center of the hole at the bottom of the template that corresponds with
your display orientation.
14
Planar UltraRes Series User Manual
Installing the Planar Profile Mounting System
7 If you have screwed the template in place, remove each screw and the template.
8 Turn the template horizontally and line the appropriate center hole up with the
bottom hole you marked on the wall. This time, use the “LONG CENTER” for a
landscape panel and the “SHORT CENTER” for a portrait panel. Ensure that the
template is flat against the wall and level.
9 Mark hole locations for the bottom mounts. One side should use the next hole in
from the “TOP” labeled hole and the other should use the next inward hole from
“P BTM” for landscape or “L BTM” for portrait (ignoring the centering holes).
Planar UltraRes Series User Manual
15
Installing the Planar Profile Mounting System
10 Line up the middle hole of the top wall mount with the screw hole drilled from
the template.
Note: This picture shows mounts for a landscape installation.
11 Tighten the screw into the mount.
12 Use a level to make sure the mount is level.
13 Then install additional screws as needed.
Note: Screws installed near the mount hooks provide the best support.
16
Planar UltraRes Series User Manual
Installing the Planar Profile Mounting System
14 Install the bottom mount brackets such that the holes marked earlier line up with
the inner bottom hole on the bottom mount bracket. Ensure the bottom mounts
are level and install at least one additional screw in each bottom mount.
Planar UltraRes Series User Manual
17
Installing the Planar Profile Mounting System
15 Using three physically capable people, carefully hang the back of the display
onto the top wall mount bracket using the square brackets on the back of the
display.
18
Planar UltraRes Series User Manual
Installing the Planar Profile Mounting System
Caution: Be sure these are securely hung, as the top of the wall mount will hold all of the
weight of the display.
As an alternative, you can use the optional lift blocks along with a lift assist mechanism to lift the panel into place. For details, refer to "Using the Lift Blocks" on
page 20.
16 On the bottom wall mounts, there is locking hardware on the bottom of each
mount. Push the hardware up and finger tighten the captive screws on the
bottom to secure the display to the wall.
Planar UltraRes Series User Manual
19
Using the Lift Blocks
Using the Lift Blocks
1 Attach the lift blocks to the back of the panel using the provided M8 x 35 pan
head screws.
2 Securely attach your lift mechanism to the eyehooks:
a Spreader bar attachment: A spreader bar allows for a small lift profile and less
stress on the panel and eyehooks than a single point attachment. This is the
preferred method.
Spreader Bar Lift: Portrait
Spreader Bar Lift: Landscape
20
Planar UltraRes Series User Manual
Using the Lift Blocks
b Single point attachment: The angle between the top of the panel and the
support lines should not be less than 45 degrees.
Singe Point Lift: Portrait
Singe Point Lift: Landscape
3 Lift the panel into place.
4 Detach the upper half of the lift block from the lower half by removing the two
vertical screws. This leaves the bottom half attached to the panel but hidden.
Planar UltraRes Series User Manual
21
Using the Kickstand Bracket
Using the Kickstand Bracket
The kickstand bracket is used for service mode, without having to remove the display
from the wall. Use the following instructions to put the display in service mode.
1 Loosen the captive locking screws on both sides of the bottom mount, and let the
brackets hang down freely.
22
Planar UltraRes Series User Manual
Using the Kickstand Bracket
2 Pull the display out and then swing the kickstands down to hold it in place. The
kickstands will nest into the bottom mount brackets. Make sure to use both
kickstands as using only one can cause stresses in the panel that could cause
damage.
Planar UltraRes Series User Manual
23
Cable Length Recommendations
Cable Length Recommendations
Cable length performance may vary between different cables and sources. The
recommended maximum DisplayPort length is 3m for DisplayPort 1.2 and 5m for
DisplayPort 1.1. HDMI cable length is recommended as follows:
• 4K @ 50/60Hz: 5m maximum
• 4K @ 24/25/30Hz: 15m maximum
• 1080p @ 60Hz and lower resolutions: 30m maximum
24
Planar UltraRes Series User Manual
Installing OPS Expansion (Optional)
Installing OPS Expansion (Optional)
Planar UltraRes Series displays are equipped with an expansion slot that supports the
Intel® Open Pluggable Specification (OPS). The slot will support OPS devices such as
PC’s, SDI modules, HDBaseT receivers, etc.
To install an OPS device, remove the protective cover on the display and slide the
device firmly into position. When installed, the OPS device will be connected
internally to the display. No external video or power cables are required.
For convenience, two Type-A USB 2.0 ports and one Type-A USB 3.0 port are provided
on the side I/O panel below the OPS slot. When an OPS device is installed, these USB
ports can be used for a keyboard, webcam, USB drive, or other peripherals.
Planar UltraRes Series User Manual
25
Supported Graphics Cards
Supported Graphics Cards
Planar UltraRes Series displays support a variety of graphics cards from leading
manufacturers, such as NVIDIA and AMD. In general, you should be looking for
graphics cards that have the following features:
• Can output 3840 x 2160 at 24 Hz or 30 Hz over a single DisplayPort or HDMI
connection.
• Four-output graphics cards that can output synchronized (genlocked) 1920 x
1080 outputs at up to 60 Hz.
• Cards that support Planar’s support timings, as listed in the following section
"Signal Compatibility" on page 80.
Caution: Before you purchase a graphics card for your source, contact your Sales
Representative to get the most current information on Planar’s compatibility with leading
graphics cards.
26
Planar UltraRes Series User Manual
Operating the Display
OSD Keypad
The OSD keypad is located on the rear of the display.
OSD Keypad Buttons
Key
Descriptions
Power
Power on/Power off

Menu Left/Decrease value

Menu Right/Increase value

Menu Up/Increase volume

Menu Down/Decrease volume
Menu
Menu/Exit
SRC
Source selection (toggle)
Planar UltraRes Series User Manual
27
Remote Control Receiver
Remote Control Receiver
The remote control receiver is located near the keypad on the rear of the display. Use
the IR extender cable for operating the remote from the front of the display.
28
Planar UltraRes Series User Manual
LED Indicators
LED Indicators
The LED indicator light is located on the rear of the display near the keypad. The
following table explains what the different colors and blink patterns mean.
LED On
Power Status
Condition
Green
Standby mode
Amber
Full power mode
Green Flashing (1 Hz)
AC power on
Green Flashing (0.5 Hz)
Powering on from standby
Green Flashing (5 Hz)
Firmware updating
Amber Flashing (5 Hz)
Power supply failure
Green and Amber
Firmware update failure
Using the Display in Portrait Mode (UR8451-MX and UR9851
Only)
When using the display in the portrait position and looking at the rear of the display,
it should be rotated according to the arrow stickers on the back of the display. This
will allow for proper ventilation. Then select the OSD rotation of landscape or portrait
on the OSD menu (MAIN MENU > ADVANCED SETTINGS > MENUS AND MESSAGES >
OSD ROTATION).
Caution: Improper ventilation may shorten the life of the display.
Using the Display in Flat or Tilted Orientation
The display is not recommended for use in flat orientation for tabletop, floor, or
ceiling installations. LCD panels of this size are at risk of panel deflection, which can
cause cosmetic sagging, brightness uniformity issues, a shortened life span, and
malfunction of optional touch sensors. Installations where the display is tilted
downward or upward at an angle may also be prone to these issues and are not
recommended.
Planar UltraRes Series User Manual
29
Using the Remote Control
Using the Remote Control
Below is a picture of the remote control. See the following page for button
descriptions and Hex codes.
30
Planar UltraRes Series User Manual
IR Command Protocol
IR Command Protocol
The Planar UltraRes displays accept commands in the form of IR signals that conform
to the NEC protocol. Each Planar UltraRes remote control has an NEC control code
associated with it. You can use these codes to program a third-party “universal”
remote control to work with the Planar UltraRes displays. These third-party products
usually come with a computer software application for this purpose. For more
information, consult the documentation provided with the remote control.
The IR control codes have the following characteristics:
• Each code consists of the following:
• A leader pulse (a modulated pulse of 9 ms followed by a non-modulated
pulse of 4.5 ms)
• 16 address bits. The default address is 1785 (0x06F9, binary 00000110
11111001)
• 16 data bits: eight (8) bits for the command followed by the logical inverse
of the command
• An end pulse (a modulated pulse of 0.56 ms, similar to the modulated
pulse in the ‘0’ and ‘1’ bits). The end of the modulated pulse constitutes the
end of the data transmission.
• The carrier frequency is 38 kHz, with the modulated pulses having a 33% duty
cycle.
• Commands are sent at a maximum rate of 9 Hz.
For example, below is the NEC control code for the ON button of the Planar UltraRes
remote control (assuming the default address is used).
Hex
06
F9
01
FE
Binary
00000110
11111001
00000001
11111110
Command
Command (Logical
Inverse)
Function
Address Byte 1 Address Byte 2
Leader Pulse
9 ms
13.5 ms
Address Byt e 1
4.5 ms
0 0 0 0 0 1
1
Address Byte 2
0 1
1
1
1
1
27 ms
Planar UltraRes Series User Manual
Command Byte
0 0 1
0 0 0 0 0 0 0 1
Command Byte (logic al invers e)
1
1
1
1
1
1
1
0
End Pulse
The following example shows the pulse train for this command.
27 ms
31
IR Command Protocol
Remote Control
Button Name
Address
Data
NEC Data From
Remote (Hex Code)
Description
ON
1785
1
0x06F901FE
Power on
OFF
1785
9
0x06F909F6
Power off

1785
2
0x06F902FD
Not used

1785
3
0x06F903FC
Not used
**
1785
6
0x06F906F9
Not used
PRESETS
1785
4
0x06F904FB
Opens the Presets menu
PRESET 1
1785
5
0x06F905FA
Applies Preset 1
PRESET 2
1785
7
0x06F907F8
Applies Preset 2
PRESET 3
1785
8
0x06F908F7
Applies Preset 3
PRESET 4
1785
10
0x06F90AF5
Applies Preset 4
1
1785
12
0x06F90CF3
Number button 1
2
1785
13
0x06F90DF2
Number button 2
3
1785
14
0x06F90EF1
Number button 3
4
1785
15
0x06F90FF0
Number button 4
5
1785
16
0x06F910EF
Number button 5
6
1785
17
0x06F911EE
Number button 6
7
1785
20
0x06F914EB
Number button 7
8
1785
25
0x06F919E6
Number button 8
9
1785
27
0x06F91BE4
Number button 9
0
1785
18
0x06F912ED
Number button 0
VOL +
1785
28
0x06F91CE3
Volume increase
VOL -
1785
33
0x06F921DE
Volume decrease
MUTE
1785
32
0x06F920DF
Audio mute
COLOR
1785
19
0x06F913EC
Not used
VIDEO WALL
1785
34
0x06F922DD
Opens the Tiling menu
MISC
1785
11
0x06F90BF4
Opens the Image Information menu
MENU
1785
21
0x06F915EA
Opens the menu
PREV
1785
22
0x06F916E9
Returns to the previous menu
ENTER
1785
23
0x06F917E8
Selects the current menu item
UP
1785
26
0x06F91AE5
Navigate up
DOWN
1785
29
0x06F91DE2
Navigate left
LEFT
1785
31
0x06F91FE0
Navigate right
RIGHT
1785
24
0x06F918E7
Navigate down
32
Planar UltraRes Series User Manual
Locking the Keypad and IR Remote
Remote Control
Button Name
Address
NEC Data From
Remote (Hex Code)
Data
Description
TOP
1785
30
0x06F91EE1
Selects the top line in the current menu
ZONE 1
1785
35
0x06F923DC
Selects the input for Zone 1
ZONE 2
1785
36
0x06F924DB
Selects the input for Zone 2
ZONE 3
1785
38
0x06F926D9
Selects the input for Zone 3
ZONE 4
1785
39
0x06F927D8
Selects the input for Zone 4
PIP MODE
1785
37
0x06F925DA
Selects the Multi-Source View setting
PIP SWAP
1785
40
0x06F928D7
Swaps the main and PIP windows
HDMI 1
1785
41
0x06F929D6
Selects HDMI 1 for the current zone
HDMI 2
1785
42
0x06F92AD5
Selects HDMI 2 for the current zone
HDMI 3
1785
43
0x06F92BD4
Selects HDMI 3 for the current zone
HDMI 4
1785
44
0x06F92CD3
Selects HDMI 4 for the current zone
DP
1785
45
0x06F92DD2
Selects DP for the current zone
DVI
1785
46
0x06F92ED1
Not used
VGA
1785
47
0x06F92FD0
Not used
OPS
1785
48
0x06F930CF
Selects OPS for the current zone
Locking the Keypad and IR Remote
You can lock the keypad and IR remote functionality on the display. To lock the
keypad, go to Main Menu -> Advanced Settings -> System Settings and select
Keypad Lock. To lock the IR remote, go to Main Menu -> Advanced Settings -> System
Settings and select IR Remote Lock.
Unlocking the Keypad and IR Remote
To unlock the keypad, press the following keys on the keypad in the order listed: UP,
UP, RIGHT, LEFT, DOWN. If the IR remote is unlocked, you can also unlock the keypad
by using the IR remote to go to Main Menu -> Advanced Settings -> System Settings
and uncheck Keypad Lock.
To unlock the IR remote, press the following keys on the IR remote in the order listed:
UP, UP, RIGHT, LEFT, DOWN. If the keypad is unlocked, you can also unlock the IR
remote by using the keypad to go to Main Menu -> Advanced Settings -> System
Settings and uncheck IR Remote Lock.
Changing the IR Remote Code Set
The IR remote code set transmitted by the remote and accepted by the display can
be configured. This is useful if there are multiple Planar displays and you would like
each remote to work only with one of the displays. It can also be used if IR
interference with another device, such as a DVD player, is occurring.
Planar UltraRes Series User Manual
33
Turning the Display On
To change the IR code on the remote, use the following procedure:
1 Press and hold the CODE button on the remote control until the LED on the
remote lights solid red (approximately five seconds).
2 Enter a new five-digit code between 00000 and 65535. Include leading zeros for
codes with four or fewer digits; for example, enter 255 as 00255.
3 The LED turns off to confirm the code change. If you enter an invalid code, the
LED flashes for three or four seconds. Try again, entering a valid code.
Note: The code must match the IR Remote ID Code setting. See page 65.
Turning the Display On
1 Insert the power cord into the display and into the power outlet.
2 Ensure the AC switch is set to “—“.
3 Press the ON button on the remote or the power button on the keypad.
Turning the Display Off
With the power on, press the OFF button on the remote or the power button on the
keypad to put the LCD panel in a standby mode. To turn off power completely, turn
the AC switch to “O” or disconnect the AC power cord from the power outlet.
Note: The display may automatically turn off the backlight or enter standby mode if no
signal is present for a certain period of time. See the description of the Power Saving Mode
setting on page 47 for more information.
Adjusting the Volume
1 Using the remote, press the VOL + or VOL - to increase or decrease the volume.
You can also use the Up and Down keys on the remote and keypad to increase or
decrease the volume.
2 Press the MUTE button to temporarily turn off all sound. To restore the sound,
press the MUTE button again.
Note: The analog audio out is variable. S/PDIF is fixed.
34
Planar UltraRes Series User Manual
Selecting Layouts and Input Sources
Selecting Layouts and Input Sources
With Planar MediaPlex Plus Processing, you can show one source at a time or multiple
sources simultaneously. Multiple layout options are available and can be selected
from the Inputs and Views Menu (see page 37). Once a layout has been designated,
you can assign sources to each of the zones in the layout. The selection of sources
must be made one at a time by assigning a current zone. To select the current zone,
you can navigate through the on-screen menu (see page 37). Alternatively, you can
use the remote or keypad as described next.
Remote
Press the Zone 1, Zone 2, Zone 3, or Zone 4 buttons on the remote. After selecting
the desired zone, you can press the source button (DP, HDMI 1, HDMI 2, HDMI 3,
HDMI 4, or OPS). This action will also select the active audio source.
For example, to change Zone 3 to OPS, press the Zone 3 button and then press the
OPS button.
Keypad
Press the SRC button. The input source will be toggled in the following order: HDMI 1,
HDMI 2, HDMI 3, HDMI 4, DP, OPS).
Note: Sources will toggle through the current zone, or last zone to be modified. Current
zones can only be re-assigned in the on-screen menu.
Planar UltraRes Series User Manual
35
Navigating Through the Menus
Navigating Through the Menus
1 With the power on, press MENU. The MAIN menu appears.
2 Within the menu, use , , ,  and ENTER to navigate through the menus and
adjust options.
3 Press PREV on the remote control, or MENU on the keypad, to return to the
previous menu. To exit the menu system, press MENU on the remote control, or
continue to press MENU on the keypad until the main menu is reached.
36
Planar UltraRes Series User Manual
Inputs and Views Menu
Inputs and Views Menu
This menu shows how the sources will be laid out on the screen based on the current
Multi-Source View and Advanced Layouts selections.
Multi-Source View
Select the Multi-Source View mode
Options: Single, Dual, Triple, Quad, PIP; Default: Single
Note: For the Advanced Layouts submenu, refer to page 38.
Note: You can only use 4K/60Hz in Single mode.
Zone 1
Select the source displayed in Zone 1
Options: HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, OPS; Default: HDMI 1
Note: If HDMI1 was selected as another source, OPS cannot be selected. If OPS was
selected as another source, HDMI1 cannot be selected.
Zone 2
Select the source displayed in Zone 2
Options: HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, OPS; Default: HDMI 2
Note: If HDMI1 was selected as another source, OPS cannot be selected. If OPS was
selected as another source, HDMI1 cannot be selected.
Planar UltraRes Series User Manual
37
Inputs and Views Menu
Zone 3
Select the source displayed in Zone 3
Options: HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, OPS; Default: HDMI 3
Note: If HDMI1 was selected as another source, OPS cannot be selected. If OPS was
selected as another source, HDMI1 cannot be selected.
Zone 4
Select the source displayed in Zone 4
Options: HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, OPS; Default: HDMI 4
Note: If HDMI1 was selected as another source, OPS cannot be selected. If OPS was
selected as another source, HDMI1 cannot be selected.
Auto Scan Sources
Select whether the display will automatically scan for a valid source on any zone that
currently does not have a source
Options: On, Off; Default: Off
Advanced Layouts Submenu
This submenu defines the layouts for each multi-source view type.
Dual
Select from two dual source layout options. The layout in orange will be the active
layout displayed when the Multi-Source View is set to Dual.
Triple
Select from five triple source layout options. The layout in orange will be the active
layout displayed when the Multi-Source View is set to Triple.
38
Planar UltraRes Series User Manual
Inputs and Views Menu
PIP
Select from four PiP (Picture-in-Picture) layouts. The layout in orange will be the active
layout displayed when the Multi-Source View is set to PiP.
PIP Size
Select the size of the PiP (Picture-in-Picture) window.
Planar UltraRes Series User Manual
39
Image Adjust Menu
Image Adjust Menu
This menu is used for making common image adjustments for the current zone.
Current Zone
The zone that is currently being adjusted. All of the settings in this menu are saved per
input. The zone’s corresponding input source is shown in the title bar, and the graphic
beneath that shows which zone is being adjusted in the current Multi-Source View
mode and Advanced Layout setting (if applicable).
The current zone can be changed via the menu or by using the ZONE 1-4 keys on the
remote control.
Note: Changing the Current Zone setting via the ZONE 1-4 keys also changes the Audio
Select setting.
40
Planar UltraRes Series User Manual
Image Adjust Menu
Brightness
Adjust the brightness value of the image
Range: 0~100; Default: 50
Contrast
Adjust the contrast of the image
Range: 0~100; Default: 50
Color
Adjust the saturation of the image
Range: 0~100; Default: 50
Tint
Adjust the hue of the image
Range: 0~100; Default: 50
Sharpness
Adjust the sharpness of the image. Higher numbers are sharper
Range: 0~10; Default: 5
Noise Reduction
Turn on noise reduction processing
Options: Off, Low, Medium, High; Default: Off
Diagnostic Color
Set the image to monochrome. This setting is for use in adjustments to a test pattern
and is not stored.
Options: Off, Red, Green, Blue; Default: Off
Color Space
Set the color space of the image
Options: REC601, REC709, RGB, RGB Video, Auto; Default: Auto
Color Temperature
Set the color temperature of the image
Options: 3200K, 5500K, 6500K, 7500K, 9300K, Native; Default: Native
Red Gain
Adjust the red gain of the image
Range: 0~200; Default: 100
Green Gain
Adjust the green gain of the image
Range: 0~200; Default: 100
Planar UltraRes Series User Manual
41
Image Adjust Menu
Blue Gain
Adjust the blue gain of the image
Range: 0~200; Default: 100
Red Offset
Adjust the red offset of the image
Range: 0~100; Default: 50
Green Offset
Adjust the green offset of the image
Range: 0~100; Default: 50
Blue Offset
Adjust the blue offset of the image
Range: 0~100; Default: 50
Gamma
Set the gamma of the image
Options: 1.5, 1.55, 1.6, 1.65, 1.7, 1.75, 1.8, 1.85, 1.9, 1.95, 2.0, 2.05, 2.1, 2.15, 2.2, 2.25, 2.3,
2.35, 2.4, 2.45, 2.5, 2.55, 2.6, 2.65, 2.7, 2.75, 2.8
Default: 2.2
Content Rotation
Rotate the image on the display
Options: None, 90, 180, 270; Default: None
Aspect Ratio
Set how the source is treated when the aspect ratio of the input is different than the
aspect ratio of the zone it is in. If the image does not fill the zone completely, the extra
margins are black.
Options: Auto, 16:9, 4:3, Fill Screen, Native, Letterbox; Default: Auto
Overscan
Set the percentage of the image to remove from each edge
Range: 0~20; Default: 0
Image Position
Move the image horizontally or vertically. The amount to move is measured in input
pixels.
Range: -1000~1000; Default: 0
Revert to Defaults
Reset all settings in the Image Adjust menu to their factory defaults for the current zone
only
42
Planar UltraRes Series User Manual
Audio Menu
Audio Menu
This menu enables you to make audio adjustments to the selected zone.
Note: Volume, Bass, Treble and Balance do not apply to the S/PDIF output.
Audio Select
The zone that is currently being adjusted and whose audio is being played. The zone’s
corresponding input source is shown in the title bar.
Options: Zone 1, Zone 2, Zone 3, Zone 4; Default: Zone 1
Note: Changing the Audio Select setting via the ZONE 1-4 keys also changes the Current
Zone setting.
Volume
Set the volume of the audio
Range: 0~100; Default: 50
Bass
Set the bass level
Range: 0~100; Default: 50
Note: This setting applies only to the internal speakers, and cannot be adjusted for the
Line Out connector.
Treble
Set the treble level
Range: 0~100; Default: 50
Note: This setting applies only to the internal speakers, and cannot be adjusted for the
Line Out connector.
Planar UltraRes Series User Manual
43
Audio Menu
Balance
Set the audio balance
Range: 0~100; Default: 50
Enable Internal
Speakers
Disable or enable the built-in speakers
Options: On, Off; Default: On
Mute
Mute or unmute the audio
Options: On or Off; Default: Off
44
Planar UltraRes Series User Manual
Presets Menu
Presets Menu
This menu enables you to save Inputs and Views settings, Image Adjust settings,
Audio settings, the Backlight Intensity setting, the Local Dimming setting, and Tiling
settings. You can save up to 10 presets using this menu (more can be saved via the
serial command interface). If a preset is saved, it will appear as “Preset 1”, “Preset 2”,
and so on. If it is not saved, it will appear as “<Empty>”.
Recall
Apply the setup from the selected preset
Range: Preset 1~Preset 10
Save
Save the current setup for later recall
Range: Preset 1~Preset 10
Delete
Delete the selected preset
Range: Preset 1~Preset 10
Planar UltraRes Series User Manual
45
Advanced Settings Menu
Advanced Settings Menu
Panel Brightness Submenu
Intensity
Set the intensity of the LCD backlight
Range: 0~100; Default: 75
Local Dimming
Turn on or off the local dimming function, if supported by the display
Options: On, Off; Default: On
Note: This setting is not supported on the 75”.
46
Planar UltraRes Series User Manual
Advanced Settings Menu
Power Submenu
Auto Power On
Set whether the system will automatically leave standby mode after AC power is applied
Options: On, Off; Default: Off
Power Saving Mode
Set the action to take if there is no signal detected after the period of time selected by
the Power Saving Delay setting:
•
Disabled: The display will remain on even if no signal is present.
•
Low Power: The display will enter standby mode if no signal is detected after the
specified period of time.
•
Wake on Signal: The display will enter a reduced power mode if no signal is
detected after the specified period of time. When in this state, the display will turn
on when a signal is detected or when any key is pressed on the keypad or IR remote.
Power Saving Delay
Set the number of minutes to delay before initiating the power saving mode action (if
any)
Options: 1 Minute, 5 Minutes, 15 Minutes, 30 Minutes, 60 Minutes; Default: 5 minutes
Power On Delay
Select the amount of time to delay before turning on the display. Depending on the
electrical capabilities at the installation site, it can be necessary to adjust the power on
sequence of the displays if there are multiple displays in the installation. Use this control
to ensure that each display will power on at a different time, avoiding such problems.
Options: 0-10 seconds, in 0.1 second increments; Default: 0 seconds
OPS Power Down Check
When this is enabled, the system will wait for a signal from the OPS module indicating it
has finished its power down sequence before going into standby
Options: Disable, Enable; Default: Enable
Planar UltraRes Series User Manual
47
Advanced Settings Menu
Network Submenu
The default static IP values are:
• IP Address: 192.168.12.12
• Subnet Mask: 255.255.255.0
• Default Gateway: 192.168.12.1
The static IP settings that you program will be used if a DHCP server cannot be found.
MAC Address
The MAC address of the system
IP Address
The current network address. You can use the number keys on the remote to enter this
information.
Subnet Mask
The current subnet mask. You can use the number keys on the remote to enter this
information.
Default Gateway
The current default gateway. You can use the number keys on the remote to enter this
information.
DNS Server
The current DNS server. You can use the number keys on the remote to enter this
information.
Note: The specified DNS server is used when Use Network Time is checked for the Set
Date and Time setting.
DHCP
Turn DHCP on or off
Options: On, Off; Default: On
48
Planar UltraRes Series User Manual
Advanced Settings Menu
Menus and Messages Submenu
Menu Position
Move the OSD menu to a different location on the screen
Options: Center, Upper Left, Upper Right, Lower Left, Lower Right; Default: Center
OSD Transparency
Set the transparency of the OSD so that the image behind it can be seen. Higher values
mean greater transparency.
Range: 0~5; Default: 0
OSD Timeout
Set the amount of time in seconds since the last keypress before the OSD menu
automatically closes. If set to Off, the menu never automatically closes.
Options: Off, 10 Seconds, 30 Seconds, 60 Seconds, 120 Seconds, 240 Seconds; Default:
60 Seconds
Allow Pop Up Messages
Suppress messages that pop up automatically. When set to No, the source status
message and the volume slider bar will not be displayed.
Options: Yes or No; Default: Yes
Allow Splash Screen
Enable or disable the splash screen during startup
Options: Enable or Disable; Default: Enable
OSD Rotation
Rotate the OSD menu so that it is readable if the display is mounted in portrait
orientation
Options: Landscape or Portrait; Default: Landscape
Planar UltraRes Series User Manual
49
Advanced Settings Menu
Blank Screen Color
Select the color to display when there is no signal in a zone
Options: Black, White, Gray, Red, Green, Blue, Cyan, Magenta, Yellow
Default: Black
Schedule Submenu
50
Planar UltraRes Series User Manual
Advanced Settings Menu
Set Date and Time
Set the internal system clock. If Use Network Time is unchecked, you can set the
following settings individually: Time Zone, Year, Month, Day, Date, Hour, and Minute.
Note: If Use Network Time is checked and DHCP is unchecked, the display will be unable
to obtain the network time unless a DNS server is programmed. This is done via the DNS
Server setting in the Network menu or the serial command interface.
Set Event 1~Event 20
Event Enabled: Turns on the event. If disabled, the settings are saved so that the event
can be re-enabled.
Frequency: The frequency of the event. Options are Daily, Weekly, Weekdays, Weekends.
Action: The action to take for the event. Options are Turn On, Turn Off, Recall, Panel
Brightness.
Data: The preset to recall when the Action is set to Recall, or the backlight setting when
the Action is set to Panel Brightness.
Planar UltraRes Series User Manual
51
Advanced Settings Menu
EDID Submenu
This menu specifies the EDID format and preferred timing for the selected connector.
Selected Connector
Set which connector is used
Options: HDMI 1, HDMI 2, HDMI 3, HDMI 4, DP, OPS, All
Program EDID
Program the EDID information for the selected connector based on the selections in the
EDID submenu
EDID Type
Set the EDID type to determine the base EDID used for the current connector:
•
4K60 selects an EDID format compliant with HDMI 2.0 and DP 1.2
•
4K30 selects an EDID format compliant with HDMI 1.4b and DP 1.1
•
1080P selects an EDID format compliant with HDMI 1.3 and DP 1.1
Options: 4K60, 4K30, 1080P
Horizontal Active
The number of active pixels in a line
Range: 0~4095
52
Planar UltraRes Series User Manual
Advanced Settings Menu
Vertical Active
The number of active lines in a field
Range: 0~4095
Vertical Refresh Rate
The number of fields per second rounded to the nearest Hz
Range: 0~120
Fully Specified
Determine how the final detailed timing is calculated. If disabled, it is calculated based on
Horizontal Active, Vertical Active, and Vertical Refresh Rate values. If enabled, it is
calculated based on all of the EDID values except for Vertical Refresh Rate.
Options: Disabled, Enabled
Note: This setting should only be enabled by advanced users.
Pixel Clock
The value of the pixel clock, in megahertz
Range: 0~600.00, in 0.01 increments
Horizontal Blanking
The number of non-active pixel clocks in a line
Range: 0~1023
Horizontal Front Porch
The number of pixel clocks in the horizontal front porch
Range: 0~1023
Horizontal Sync Width
The number of pixel clocks in the horizontal sync pulse
Range: 0~255
Vertical Blanking
The number of non-active lines in a field
Range: 0~255
Vertical Front Porch
The number of line times in the vertical front porch
Range: 0~255
Vertical Sync Width
The number of line times in the vertical sync
Range: 0~255
Planar UltraRes Series User Manual
53
Advanced Settings Menu
Revert to Factory
Reset the EDID type and timings to the default values for the selected connector
Advanced Color Submenu
This menu adjusts the color coordinates of the current zone. These controls are used
by advanced installers to achieve exact color point targets on the display. In some
cases, the target color coordinates may not be achievable. In this case, an asterisk (*)
will appear next to the color coordinate value.
Note: The white color point should be adjusted before adjusting the other color points.
54
Planar UltraRes Series User Manual
Advanced Settings Menu
Current Zone
The zone that is currently being adjusted. All of the settings in this menu are saved per
zone, and all color coordinate values are also saved per Color Gamut setting. The zone’s
corresponding input source is shown in the title bar, and the graphic beneath that shows
which zone is being adjusted in the current Multi-Source View mode and Advanced
Layout setting (if applicable).
The current zone can be changed via the menu or by using the ZONE 1-4 keys on the
remote control.
Note: Changing the Current Zone setting via the ZONE 1-4 keys also changes the Audio
Select setting.
White x
Adjust the x coordinate of the white color point
Range: 0.000-0.800
White y
Adjust the y coordinate of the white color point
Range: 0.000-0.800
Red x
Adjust the x coordinate of the red color point
Range: 0.000-0.800
Red y
Adjust the y coordinate of the red color point
Range: 0.000-0.800
Green x
Adjust the x coordinate of the green color point
Range: 0.000-0.800
Green y
Adjust the y coordinate of the green color point
Range: 0.000-0.800
Blue x
Adjust the x coordinate of the blue color point
Range: 0.000-0.800
Blue y
Adjust the y coordinate of the blue color point
Range: 0.000-0.800
Planar UltraRes Series User Manual
55
Advanced Settings Menu
Cyan x
Adjust the x coordinate of the cyan color point
Range: 0.000-0.800
Cyan y
Adjust the y coordinate of the cyan color point
Range: 0.000-0.800
Magenta x
Adjust the x coordinate of the magenta color point
Range: 0.000-0.800
Magenta y
Adjust the y coordinate of the magenta color point
Range: 0.000-0.800
Yellow x
Adjust the x coordinate of the yellow color point
Range: 0.000-0.800
Yellow y
Adjust the y coordinate of the yellow color point
Range: 0.000-0.800
Copy to All Zones
Copy the color coordinate settings for the current zone and the current Color Gamut
setting to all other zones
Revert to Defaults
Reset the color coordinate settings for the current zone and the current Color Gamut
setting to their default values
56
Planar UltraRes Series User Manual
Advanced Settings Menu
Tiling Submenu
This menu contains controls for using multiple UltraRes displays in a tiled
configuration. This is useful when trying to display one image across multiple
displays. In addition to setting up the width and height of the tiled wall, each display
must have its position within the tiled wall properly selected. Refer to the diagrams
below for example setting values in a 3 x 4 tiled wall.
Note: When using the Content Rotation feature, the Tiling settings must be adjusted
differently in order to display the image properly. Refer to the examples below.
Example 1: 0 Degree Rotation, Wall Width = 3, Wall Height = 4
Unit Row 1
Unit Column 1
Unit Row 1
Unit Column 2
Unit Row 1
Unit Column 3
Unit Row 2
Unit Column 1
Unit Row 2
Unit Column 2
Unit Row 2
Unit Column 3
Unit Row 3
Unit Column 1
Unit Row 3
Unit Column 2
Unit Row 3
Unit Column 3
Unit Row 4
Unit Column 1
Unit Row 4
Unit Column 2
Unit Row 4
Unit Column 3
Planar UltraRes Series User Manual
57
Advanced Settings Menu
Example 2: 180 Degree Rotation, Wall Width = 3, Wall Height = 4
58
Unit Row 4
Unit Column 3
Unit Row 4
Unit Column 2
Unit Row 4
Unit Column 1
Unit Row 3
Unit Column 3
Unit Row 3
Unit Column 2
Unit Row 3
Unit Column 1
Unit Row 2
Unit Column 3
Unit Row 2
Unit Column 2
Unit Row 2
Unit Column 1
Unit Row 1
Unit Column 3
Unit Row 1
Unit Column 2
Unit Row 1
Unit Column 1
Planar UltraRes Series User Manual
Advanced Settings Menu
Example 3: 90 Degree Rotation, Wall Width = 4, Wall Height = 3
Unit Row 3
Unit Column 1
Unit Row 2
Unit Column 1
Unit Row 1
Unit Column 1
Unit Row 3
Unit Column 2
Unit Row 2
Unit Column 2
Unit Row 1
Unit Column 2
Unit Row 3
Unit Column 3
Unit Row 2
Unit Column 3
Unit Row 1
Unit Column 3
Unit Row 3
Unit Column 4
Unit Row 2
Unit Column 4
Unit Row 1
Unit Column 4
Planar UltraRes Series User Manual
59
Advanced Settings Menu
Example 4: 270 Degree Rotation, Wall Width = 4, Wall Height = 3
60
Unit Row 1
Unit Column 4
Unit Row 2
Unit Column 4
Unit Row 3
Unit Column 4
Unit Row 1
Unit Column 3
Unit Row 2
Unit Column 3
Unit Row 3
Unit Column 3
Unit Row 1
Unit Column 2
Unit Row 2
Unit Column 2
Unit Row 3
Unit Column 2
Unit Row 1
Unit Column 1
Unit Row 2
Unit Column 1
Unit Row 3
Unit Column 1
Planar UltraRes Series User Manual
Advanced Settings Menu
Tiling Enabled
When enabled, the tiling parameters in the menu are used
Options: Disable, Enable; Default: Disable
Wall Width,
Wall Height
Select the width and height of the tiled wall
Default: Width=1, Height=1
Unit Column,
Unit Row
Selects the location of the current display within the tiled wall
Default: Column=1, Row=1
Frame Compensation
When enabled, the image is scaled to compensate for the width of the display’s bezel,
using the Frame Width and Frame Height parameters. See "Frame Compensation
Examples" on page 62.
Options: Disable, Enable; Default: Disable
Frame Width,
Frame Height
Selects how many lines/pixels are removed from the image to compensate for the
display’s bezel
Planar UltraRes Series User Manual
61
Advanced Settings Menu
Frame Compensation Examples
Below are examples with the Frame Compensation feature enabled (left) and
disabled (right). Note that the eagle’s eye is noticeably different when Frame
Compensation is disabled.
62
Planar UltraRes Series User Manual
Advanced Settings Menu
Test Patterns Submenu
This menu selects a test pattern to show on the display for diagnostic purposes.
Test Patterns
Options: Black, Gray, White, Red, Green, Blue, Magenta, Yellow, Cyan, Gray Ramp, Red
Ramp, Blue Ramp, Color Bar, Checkerboard
Planar UltraRes Series User Manual
63
Advanced Settings Menu
System Settings Submenu
Touch Control
Set where the USB commands from the touch panel is routed:
•
OPS routes the touch USB commands to the OPS module
•
External routes the touch USB command to the USB-B connector
•
Auto routes the touch USB commands to the OPS module if the OPS source is
selected; otherwise, they are connected to the USB-B connector
Enable Status LED
When enabled, the status LEDs on the back of the display behave as indicated on
page 29. When disabled, the status LEDs are always turned off.
Options: Disable, Enable; Default: Enable
Pixel Orbit
Create slight frame motion to help avoid image retention
Options: Enable, Disable; Default: Disable
MEMC
Enable motion estimation motion compensation (frame interpolation). This improves
smoothness for fast motion video content.
Options: Off, Low, Medium, High; Default: Off
DisplayPort Type
Set the version of DisplayPort that is used by the system
Options: 1.1, 1.2; Default: 1.2
64
Planar UltraRes Series User Manual
Advanced Settings Menu
Keypad Lock
Lock or unlock the keypad. When it is enabled, all keypad presses will be ignored.
Options: Enable, Disable; Default: Disable
IR Remote Lock
Lock or unlock the remote control. When it is enabled, all remote control presses will be
ignored.
Options: Enable, Disable; Default: Disable
IR Remote ID Code
Selects the IR remote code set accepted by the display
Options: 00000-65535; Default: 01785
Save All Settings to USB
Save all settings in the display to a USB flash drive. The saved file will be named
Planar-settings.bin and will be saved in the root folder of the USB flash drive.
Note: A USB flash drive must be inserted into the USB-A connector prior to using this
feature. The USB flash drive must be formatted as FAT32. This feature will not work with
the NTFS file system.
Restore All Settings
from USB
Restores all settings in the display from a USB flash drive. The settings file must be named
Planar-settings.bin and must be located in the root folder of the USB flash drive.
Note: A USB flash drive must be inserted into the USB-A connector prior to using this
feature. The USB flash drive must be formatted as FAT32. This feature will not work with
the NTFS file system.
Save Diagnostics to USB
Save a diagnostic report to a USB flash drive to help Planar Technical Support
troubleshoot any issues. The saved file will be named Planar-diagnostics.bin and will be
saved in the root folder of the USB flash drive.
Note: A USB flash drive must be inserted into the USB-A connector prior to using this
feature. The USB flash drive must be formatted as FAT32. This feature will not work with
the NTFS file system.
Factory Reset
Return the saved settings in a system to their factory defaults
Firmware Update
Update the firmware for the display. Refer to the instructions on the firmware release
package for more information.
Planar UltraRes Series User Manual
65
Information Menu
System Information Submenu
This menu displays version information for all programmable parts in the system. It
also contains the model and serial number.
Planar UltraRes Series User Manual
66
Information Menu
Image Information Submenu
This menu displays image details for the current zone. If more than one zone is
available, you can change zones by setting the Current Zone option.
Planar UltraRes Series User Manual
67
Information Menu
Error Log Submenu
This menu displays a chronological list of system errors that have occurred. For a list
of possible errors, see "Error Codes" on page 93.
68
Planar UltraRes Series User Manual
Using the Touch Screen
Using the Touch Screen
You can use the touch screen to control your Windows, Mac, or Linux operating
system. The Planar UltraRes Series is HID compliant, delivering up to 12 points of
touch on both Windows and Linux without a driver. To achieve greater than 12 points
of touch on a Planar UltraRes Touch display, a driver will need to be installed on the
operating system. Drivers for Windows and Linux can be found on
http://www.planar.com/support and on the USB flash drive included with the display.
Single touch only is supported for Mac operating systems. There is no driver required
to enable Mac support.
Note: Ensure that you have installed the USB cable on the display to a computer.
Note: If an OPS PC is installed in the OPS slot, the OPS PC will automatically be connected
internally to the touch system. The touch functionality is configurable via the Touch Control
setting.
Touchscreen MultiTouch Driver Installation
1 With the PC on, plug in the USB memory stick to the USB port on your PC.
2 Locate and open the USB drive.
3 Double-click on the “mt_driver_kit [xxxxxx].exe” to install the driver.
4 Follow installation prompts until driver installation is complete.
Once driver installation is complete, the touchscreen is ready for use.
Touchscreen (PQLabs) MultiTouch Platform Content
The PQLabs Software is used for troubleshooting and calibration. The different
menus are described below.
1 On the PC, select the Start menu, All Programs and then PQLabs Software.
2 Click on “MultiTouch Platform” to open the PQLabs MultiTouch Platform window.
Touchscreen Information
• Serial Number: Displays the serial number of the connected touchscreen.
• Firmware Version: Displays the firmware version of the touchscreen selected
under the “Serial Number” dropdown menu.
• Touch Points: Displays the number of touch points for which the touchscreen is
capable.
• Status: Displays the current status of the touchscreen.
Planar UltraRes Series User Manual
69
Uninstalling the MultiTouch Driver
Calibration
• Calibration: Starts a 4-point calibration of the touchscreen. Perform the
programmed touchscreen calibration process. At the conclusion of the
calibration routine your touchscreen device is ready to use and will perform
with accurately positioned touch points.
• Reset Calibration: Resets calibration to factory default settings.
Utility
• Diagnose: Starts the “MultiTouchDoctor” program. This can be used to
troubleshoot issues with the touchscreen.
Options
• Default settings on options have the following programs enabled:
Tuio Support, Flash Tuio Support, Handwriting Optimization, Enable Windows
Native Touch, Enable Mouse/Keyboard Simulation, and Launch When Windows
Starts Up.
• Flexible Scan Rate is at a default setting.
Uninstalling the MultiTouch Driver
1 On the PC, select the Start menu, All Programs and the PQLabs Software.
2 Click on the MultiTouch Driver.
3 Select the Uninstall option.
70
Planar UltraRes Series User Manual
Planar UltraRes Remote Monitoring Software
Planar UltraRes Remote
Monitoring Software
Planar UltraRes Remote Monitoring is a software tool that displays information about
the display via a web browser. It is used primarily to access the settings in the OSD as
well as provides some additional features.
Remote Monitoring Home
Launch a web browser. Enter the IP address shown in the Network menu (see
page 48). If successful, you should see the Remote Monitoring System Information
page.
Remote Monitoring System Information
This page displays version information for all programmable parts in the system. It
also contains the model and serial number.
For the OSD equivalent, refer to "System Settings Submenu" on page 64.
Planar UltraRes Series User Manual
71
Remote Monitoring Inputs and Views
Remote Monitoring Inputs and Views
This page shows how the sources will be laid out on the screen based on the current
Multi-Source View and Advanced Layouts selections.
For the OSD equivalent, refer to "Inputs and Views Menu" on page 37.
72
Planar UltraRes Series User Manual
Remote Monitoring Audio
Remote Monitoring Audio
This page enables you to make audio adjustments to the selected zone.
Note: Volume, Bass, Treble and Balance do not apply to the S/PDIF output.
For the OSD equivalent, refer to "Audio Menu" on page 43.
Planar UltraRes Series User Manual
73
Remote Monitoring Presets
This page enables you to save Inputs and Views settings, Image Adjust settings,
Audio settings, the Backlight Intensity setting, the Local Dimming setting, and Tiling
settings. You can save up to 64 presets using this page (more can be saved via the
serial command interface). Only presets that contain saved data are shown in the
table, with buttons to recall or delete the corresponding preset.
The controls below the table enable you to save a new preset, or overwrite an
existing preset with the current display settings. To save or overwrite a preset, enter
the preset number to save or overwrite, optionally enter a custom name for the
preset, and then click the Save button.
For the OSD equivalent, refer to "Presets Menu" on page 45.
Planar UltraRes Series User Manual
74
Remote Monitoring Panel Brightness and Power
This page enables you to make adjustments to the brightness and power settings.
For the OSD equivalents, refer to "Panel Brightness Submenu" on page 46 and "Power
Submenu" on page 47.
Planar UltraRes Series User Manual
75
Remote Monitoring Notifications
Remote Monitoring Notifications
This page enables you to send email notifications on certain events.
Note: Obtain this information from your ISP or network administrator.
The options under Email Account Settings are:
• SMTP Server: The name of the outgoing SMTP server. Obtain this information
from your ISP.
• Connection Encryption: Selects the appropriate encryption method required
by the SMTP server.
• Port: Selects the port that the SMTP server uses.
• Authentication: Use Auto unless directed by your ISP or network administrator.
• User Name: Login username for the SMTP server.
• Password: Login password for the SMTP server.
• Email From Address: The email address that will be shown in the “From:” field
of the notification emails.
76
Planar UltraRes Series User Manual
Remote Monitoring System Settings
The options under Notification Events are:
• Power On/Off: Occurs when standby mode is entered and when the display is
powered on.
• System Error: Occurs when the display has detected an error within the
system.
• Source Detect: Occurs when the display detects and displays a new input
signal.
• Source Lost: Occurs when the current input signal is no longer detected.
• Source Selected: Occurs when a different input source is selected for any of the
zones.
Note: Each event can be sent to one or more recipients. To add multiple email addresses,
separate them by a space.
• Test Email: Sends a test of the selected email notification. This is useful for
verifying that your email account settings are setup correctly. If the test email
fails, you can use the View Last 10 Log Messages button to get more detailed
information about the failure.
Remote Monitoring System Settings
This page enables you to make adjustments to a variety of system settings.
For the OSD equivalent, refer to "System Settings Submenu" on page 64.
Planar UltraRes Series User Manual
77
Remote Monitoring Access Control
This page enables you to limit the ability to access certain features in the web server
by password protecting them.
All functions other than the following require Admin level access:
• Power On/Off
• System Information
• Inputs and Views
• Multi-Source View
• Zone inputs
• Presets
• Recall
• Audio
• Volume
• Mute
• Panel Brightness and Power
• Panel Brightness
With the exception of System Information, all functions listed above require User
level access.
If no password is set for either access level, all functions can be accessed. By default,
there are no passwords for either access level.
Planar UltraRes Series User Manual
78
External Control
In addition to using the Planar UltraRes remote control and display, there are other
methods of controlling the Planar UltraRes display externally:
• Using a serial link to send ASCII commands and to receive responses to those
commands. The same set of commands can be sent over RS-232, USB, TCP or
UDP. See the Planar UltraRes Series RS232 User Manual for more information.
• Using discrete infrared (IR) codes to program a third-party remote control. See
"IR Command Protocol" on page 31.
• Using the Planar UltraRes Remote Monitoring software to access the settings in
the OSD as well as some additional features via a web browser. See "Planar
UltraRes Remote Monitoring Software" on page 71.
Planar UltraRes Series User Manual
79
Signal Compatibility
80
DisplayPort
HDMI 1-2, OPS
640x480
59.94
31.469
25.175
x
x
x
VESA DMT, CEA-861-F Format 1
640x480
72
37.861
31.500
x
x
x
VESA DMT
640x480
74.99
37.500
31.500
x
x
x
VESA DMT
640x480
85
43.269
36.000
x
x
x
VESA DMT
800x600
60.32
37.890
40.000
x
x
x
VESA DMT
800x600
72
48.077
50.000
x
x
x
VESA DMT
800x600
75
46.875
49.500
x
x
x
VESA DMT
800x600
85.06
53.674
56.250
x
x
x
VESA DMT
848x480
59.659
29.830
31.500
x
x
x
VESA CVT
848x480
74.769
37.684
41.000
x
x
x
VESA CVT
848x480
84.751
42.969
46.750
x
x
x
VESA CVT
1024x768
60
48.363
65.000
x
x
x
VESA DMT
1024x768
70
56.476
75.000
x
x
x
VESA DMT
1024x768
75.03
60.023
78.750
x
x
x
VESA DMT
1024x768
85.03
68.677
94.500
x
x
x
VESA DMT
1152x864
70.012
63.851
94.500
x
x
x
VESA DMT
1152x864
75
67.500
108.000
x
x
x
VESA DMT
1152x864
84.999
77.094
121.500
x
x
x
VESA DMT
1280x768
49.929
39.593
65.250
x
x
x
VESA CVT
1280x768
59.995
47.396
68.250
x
x
x
VESA CVT-R
1280x768
60
47.776
79.500
x
x
x
VESA CVT
1280x768
74.893
60.289
102.250
x
x
x
VESA CVT
1280x768
84.837
68.633
117.500
x
x
x
VESA CVT
1280x960
60
60.000
108.000
x
x
x
VESA DMT
1280x960
75
75.000
126.000
x
x
x
VESA DMT
1280x960
85.002
85.938
148.500
x
x
x
VESA DMT
1280x1024
60.02
63.981
108.000
x
x
x
VESA DMT
1280x1024
75.02
79.976
135.000
x
x
x
VESA DMT
1280x1024
85.02
91.146
157.500
x
x
x
VESA DMT
1360x768
60
47.712
85.500
x
x
x
VESA DMT
Resolution
HDMI 3-4
Pixel Rate
(MHz)
PC
Line Rate
(kHz)
Signal
Type
Frame rate
(Hz)
Signal Compatibility
Planar UltraRes Series User Manual
References
54.113
100.000
x
x
x
VESA CVT
1400x1050
60
64.7
101.00
x
x
x
VESA CVT-R
1400x1050
60
65.317
121.750
x
x
x
VESA CVT
1400x1050
74.867
82.278
156.000
x
x
x
VESA CVT
1600x1200
60
75.000
162.000
x
x
x
VESA DMT
1920x1080
49.929
55.621
141.500
x
x
x
VESA CVT
1920x1080
59.963
67.158
173.000
x
x
x
VESA CVT
1920x1080
59.950
66.587
138.500
x
x
x
VESA CVT-R
1920x1200
49.932
61.816
158.250
x
x
x
VESA CVT
1920x1200
59.950
74.038
154.000
x
x
x
VESA CVT-R
1680x1050
49.974
54.121
119.500
x
x
x
VESA CVT
1680x1050
59.954
65.290
146.250
x
x
x
VESA CVT
1920x2160
60
135.000
297.000
x
x
x
CEA-861-F, VIC 16, with vertical
parameters doubled
2560x1440
59.951
88.787
241.500
x
x
x
VESA CVT-R
2560x1600
59.972
98.713
268.500
x
x
x
VESA CVT-R
3840x2160
24
52.438
209.750
x
x
x
VESA CVT-R
3840x2160
30
65.688
262.750
x
x
x
VESA CVT-R
3840x2160
50
110.500
442.000
x
x
VESA CVT-R
3840x2160
60
133.313
533.250
x
x
VESA CVT-R
Apple Mac 640x480
SDTV
EDTV
DisplayPort
49.965
66.59
HDMI 3-4
1400x1050
Resolution
Pixel Rate
(MHz)
Line Rate
(kHz)
PC
Frame rate
(Hz)
Signal
Type
HDMI 1-2, OPS
Signal Compatibility
x
x
x
References
832x624
75.087
49.107
55.000
x
x
x
1024x768
59.278
48.193
64.000
x
x
x
1024x768
74.927
60.241
80.000
x
x
x
1152x870
75.062
68.681
100.000
x
x
x
480i
60
x
x
x
SMPTE 125M, CEA-861-F Formats 6 & 7
576i
50
x
x
x
ITU-R BT.601, CEA-861-F Formats 21 &
22
480p
60
31.469
27.000
x
x
x
ITU-R BT.1358, CEA-861-F Format 17 &
18
576p
50
31.250
27.000
x
x
x
SMPTE 125M, CEA-861-F Format 6 & 7
Planar UltraRes Series User Manual
81
DisplayPort
HDMI 1-2, OPS
1080i
50
28.125
74.500
x
x
x
SMPTE 274M, CEA-861-F Format 20
1080i
60
33.750
74.250
x
x
x
SMPTE 274M, CEA-861-F Format 5
720p
50
37.500
74.250
x
x
x
SMPTE 296M, CEA-861-F Format 19
720p
60
45.000
74.250
x
x
x
SMPTE 296M, CEA-861-F Format 4
1080p
24
27.000
74.250
x
x
x
SMPTE 274M, CEA-861-F Format 32
1080p
25
28.125
74.250
x
x
x
SMPTE 274M, CEA-861-F Format 33
1080p
30
33.750
74.250
x
x
x
SMPTE 274M, CEA-861-F Format 34
1080p
50
56.250
148.500
x
x
x
SMPTE 274M, CEA-861-F Format 31
1080p
60
67.500
148.500
x
x
x
SMPTE 274M, CEA-861-F Format 16
3840x2160
24
54.000
297.000
x
x
x
CEA-861-F Format 93, HDMI 1.4b VIC 1
3840x2160
25
56.250
297.000
x
x
x
CEA-861-F Format 94, HDMI 1.4b VIC 2
3840x2160
30
67.500
297.000
x
x
x
CEA-861-F Format 95, HDMI 1.4b VIC 3
3840x2160
50
67.500
297.000
x
3840x2160
50
135.000
594.000
x
3840x2160
60
67.500
297.000
x
3840x2160
60
135.000
594.000
x
Resolution
HDMI 3-4
Pixel Rate
(MHz)
UHDTV
Line Rate
(kHz)
HDTV
Frame rate
(Hz)
Signal
Type
Planar UltraRes Series User Manual
References
CEA-861-F Format 96, 4:2:0 subsampling
x
CEA-861-F Format 96
CEA-861-F Format 97, 4:2:0 subsampling
x
CEA-861-F Format 97
82
Color Subsampling Support
Color Subsampling
Support
Video Timing
Input
RGB 4:4:4
Supported
YUV 4:4:4
Supported
YUV 4:2:2
Supported
4K @ 50/60 Hz
DP
x
x
x
4K @ 50/60 Hz
HDMI 1-2, OPS
x
x
x
4K @ 50/60 Hz
HDMI 3-4
All Other
Supported
Timings
Any
x
x
x
Planar UltraRes Series User Manual
YUV 4:2:0
Supported
x
83
Specifications
Specifications
Item
UR7551
UR7551-ERO
UR7551-ERO-T
UR8451-LX
UR8451-LX-ERO
UR8451-LX-ERO-T
UR8451-MX
UR8451-MX-ERO
UR8451-MX-ERO-T
UR9851
UR9851-ERO
UR9851-ERO-T
LCD Panel
Resolution
3840 x 2160
Aspect Ratio
16:9
Screen Size
75"
Orientation
Landscape
Landscape
2
2
Brightness (Typ.)
450 cd/m
84"
84"
350 cd/m
98"
Landscape/Portrait
500 cd/m2
500 cd/m2
Contrast Ratio
(local dimming
enabled)
N/A
20000:1
20000:1
20000:1
Contrast Ratio
(local dimming
disabled)
5000:1
1600:1
1400:1
1300:1
Viewing Angle
(Typ.)
178°
178°
178°
178°
Response Time
(Typ.)
6ms
5ms
5ms
8ms
Color Gamut
72% NTSC
Display Color
1.07 billion
(10 bit depth)
Connectivity
Standard Inputs
DisplayPort 1.2, HDMI 2.0 x 2,
HDMI 1.4 x 2, OPS
Audio Output
Line out, S/PDIF
Control and
Monitoring
LAN RJ45, RS232 In, IR, Keypad, Planar® UltraRes™ App
Mechanical
Display
Dimensions
(Unmounted and
Mounted)
84
Standard/ERO™:
66.6" x 38.1 x 3.6"
(1691 mm x
969 mm x 93 mm)
Standard/ERO™:
75.5" x 43.7 x 3.6"
(1919 mm x
1111 mm x 93 mm)
Standard/ERO™:
86.7" x 49.5" x 3.6"
(2203 mm x
1258 mm x 93 mm)
Touch:
67.7" x 39.2 x 4.1"
(1719 mm x
997 mm x 104 mm)
Touch:
76.4" x 44.6" x 4.1"
(1941 mm x 1133 mm x 104 mm)
Touch:
87.6" x 50.4" x 4.1"
(2225 mm x
1280 mm x 104 mm)
Planar UltraRes Series User Manual
Specifications
Item
Bezel Width
Display Weight
UR7551
UR7551-ERO
UR7551-ERO-T
UR8451-LX
UR8451-LX-ERO
UR8451-LX-ERO-T
UR8451-MX
UR8451-MX-ERO
UR8451-MX-ERO-T
UR9851
UR9851-ERO
UR9851-ERO-T
Standard/ERO: 0.8" (20
mm)
Touch: 1.4" (34mm)
Standard/ERO: 1.15" (29.1 mm) left/right; 1.26"
(32.1 mm) top/bottom
Touch: 1.58" (40.1 mm) left/right;
1.70" (43.1 mm) top/bottom
Standard/ERO: 0.9" (22
mm)
Touch: 1.3" (33 mm)
Standard: 165 lbs (75
kg)
ERO: 185 lbs (84 kg)
Touch: 205 lbs
(93 kg)
Standard: 200 lbs (91 kg)
ERO: 225 lbs
(102 kg)
Touch: 250 lbs
(113 kg)
Standard: 255 lbs (115
kg)
ERO: 305 lbs
(138 kg)
Touch: 330 lbs
(150 kg)
Mounting
Planar Profile Mounting
System or VESA
400 x 400 mm
Wall Mount
Weight
Landscape: 21.4 lbs (9.7
kg)
Portrait: 17.0 lbs (7.7 kg)
Planar Profile Mounting System or VESA
600 x 400 mm
Landscape: 22.5 lbs (10.2 kg)
Portrait: 17.6 lbs (8.0 kg)
Fanless
Landscape: 24.7 lbs
(11.2 kg)
Portrait: 19.0 (8.6 kg)
Yes
Speakers
10W x 2 built-in
Usage
Recommended
Usage
All-day
All-day
24x7
24x7
Backlight
D-LED
E-LED
E-LED
D-LED
Backlight Life
35,000 hours min
30,000 hours min
Power Source
Power
Consumption
(Typ.)
270W
360W
410W
BTUs/hr (Typ.)
270W x 3.42 BTU = 923
BTU/hr
360W x 3.42 BTU = 1231 BTU/hr
410W x 3.42 BTU = 1402
BTU/hr
Standby Power
Consumption
<1.2W
Input Voltage/
Frequency
AC 100V~240V;
50-60 Hz
Environment
Storage
Temperature
Operating
Temperature
Min -4°F ~ Max 140° F (-20°C ~ 60°C)
Min 32°F ~
Max 104°F
(0 ~ 40°C) at up to 1500
m;
Min 32°F ~
Max 95°F (0 ~ 35°C) at
up to 3000 m
Min 32°F ~ Max 95°F (0 ~ 35°C) at up to 1500 m;
Min 32°F ~ Max 86°F (0 ~ 30°C) at up to 3000 m
Planar UltraRes Series User Manual
85
Specifications
Item
UR7551
UR7551-ERO
UR7551-ERO-T
UR8451-LX
UR8451-LX-ERO
UR8451-LX-ERO-T
UR8451-MX
UR8451-MX-ERO
UR8451-MX-ERO-T
Humidity
20~85% RH
Approvals
FCC Class A, cTUVus, CE
UR9851
UR9851-ERO
UR9851-ERO-T
ERO (ERO and ERO-T models only)
Surface Treatment
Glass Type
Anti-glare (AG)
Anti-reflective (AR)
2mm Corning® Gorilla® Glass
3mm soda-lime
Touch (ERO-T models only)
Touch Technology
Supporting OS
86
IR
Windows 7, 8, 10, Vista, XP, Mac OSX, and Linux
Planar UltraRes Series User Manual
Dimensions
Dimensions
UR7551
Planar UltraRes Series User Manual
87
UR7551 Touch
Planar UltraRes Series User Manual
88
UR8451
UR8451
Planar UltraRes Series User Manual
89
UR8451 Touch
UR8451 Touch
90
Planar UltraRes Series User Manual
UR9851
UR9851
Planar UltraRes Series User Manual
91
UR9851 Touch
Planar UltraRes Series User Manual
92
Troubleshooting During Installation
Troubleshooting During
Installation
This section includes troubleshooting information about different issues you may
encounter during the installation process or after your display has been running for
some time. If you are not able to solve your issue in this section, please contact
Planar’s Technical Support team for assistance.
Error Codes
To see the last 50 errors that have occurred, select the Error Log tab in the OSD (MAIN
MENU > INFORMATION > ERROR LOG), as shown below.
Planar UltraRes Series User Manual
93
Symptoms, Possible Causes and Solutions
Possible error codes include:
•
•
•
•
Power supply 1 issue
Power supply 2 issue
Power supply 3 issue
Calibration EEPROM board disconnected
Note the following:
• One power supply failure will limit the backlight intensity to 50% maximum and
two power supply failures will shut off the display.
• Power supply 3 issues do not apply to the 75” model.
Symptoms, Possible Causes and Solutions
Below are different symptoms that you might encounter as you install your Planar
UltraRes display. First look at the different symptoms to see if you can find your issue.
And then look at the possible cause and try the suggested solution(s). If you still are
not able to resolve your issue, please contact Planar’s Technical Support Department.
Symptom: Can’t Get PC to Output 4K @ 24/30/60 Hz
Solution
Make sure that your graphics card can support a 4K output. See "Supported Graphics
Cards" on page 26 for a list of the current graphics cards that Planar supports for the
Planar UltraRes Series displays.
Solution
Confirm that you are using a DisplayPort output. You can’t use a DisplayPort-to-HDMI
adapter to output 4K content.
Solution
Make sure you are using a high-speed HDMI cable. Standard HDMI cables might work
but are not guaranteed.
Solution
Verify that the selected EDID Type setting in the OSD is 4K60 or 4K30. If you change
the EDID setting, you may need to disconnect and reconnect the cable.
Solution
If you are trying to use 4K @ 60 Hz on HDMI, the display must be connected to
HDMI 1 or HDMI 2.
94
Planar UltraRes Series User Manual
Symptom: Can’t Get PC to Output 4K @ 24/30/60 Hz
Solution
If you are trying to display 4K @ 60 Hz on HDMI 1 or HDMI 2, the Multi-Source View
setting must be Single.
Symptom: Can’t Get PC to Output 4K @ 24/30/60 Hz
Possible Cause
The connector overmold is too large, which can cause the pins not to contact
properly on some cards.
Solution
If using DisplayPort, make sure the connector overmold isn’t too large.
Overmold
is too wide
Overmold is
within
specification
Symptom: Can’t Select OPS or HDMI 1
Solution
The OPS and HDMI sources cannot be viewed at the same time. If your Multi-Source
View setting is not Single, and you select OPS in a zone, any zones that are showing
HDMI 1 will automatically change to OPS. Conversely, if you select HDMI 1 in a zone,
any zones that are currently showing OPS will automatically change to HDMI 1.
Planar UltraRes Series User Manual
95
Symptom: IR Isn’t Working Properly
Symptom: IR Isn’t Working Properly
Possible Cause
The wired IR module may not be fully connected.
Solution
Make sure the IR is fully connected by pressing hard to unsure it is inserted as far as
possible.
Possible Cause
The wired IR module cable is not being used.
Solution
Make sure that the wired IR module cable is being used.
96
Planar UltraRes Series User Manual
Accessing Planar’s Technical Support Website
Accessing Planar’s
Technical Support
Website
Visit http://www.planar.com/support for the following support documents and
resources:
•
•
•
•
•
User Manual
RS232 User Manual
Touch screen drivers
Standard warranties
Planar support hotline number and email
Planar UltraRes Series User Manual
97
Accessing Planar’s Technical Support Website
98
Planar UltraRes Series User Manual
Index
A
adjusting volume, 34
advanced settings menu, 46
audio menu, 43
avoiding temporary image retention, 4
IR codes, using, 31
IR commands
for Planar UltraRes, 31
protocol, 31
IR not working, 96
K
C
cleaning the display, 7
codes, error, 93
color subsampling, 83
connecting
touch screen, 69
control, external, 79
kickstand bracket
using, 22
L
D
LCD
installation, 11
mounts, 8
LCD display, 8
locking, 33
dimensions, 87
display
installing, 11
M
E
error codes, 93
external control, 79
I
image adjust menu, 40
information menu, 66
input source
selecting, 35
inputs and view menu, 37
installation
before you build, 11
of display on a wall, 12
of LCD, 11
OPS expansion slot, 25
safety precautions, 3
introduction, 1
menus
advanced settings, 46
audio, 43
image adjust, 40
information, 66
inputs and views, 37
presets, 45
using, 36
mounting template for LCD mounts, 8
N
navigating menus, 36
normal usage guidelines, 6
O
OPS expansion slot
installation, 25
optional
Planar UltraRes Series User Manual
i
Index
LCD mounts, 8
mounting template, 8
using the kickstand bracket, 22
osd menus, 33, 36
unlocking, 33
symptoms, 94
turning off the displays, 34
turning on the displays, 34
U
P
using the kickstand bracket, 22
using the remote, 30
package contents, 8
Planar UltraRes display
installing on a wall, 12
troubleshooting via error codes, 93
presets menu, 45
V
R
W
recommended usage, 4
remote control
using, 30
warranty
information, ii
volume, 34
S
safety
during installation, 3
information, 2
precautions, 2
precautions during use, 4
selecting input source, 35
service plans, ii
signal compatibility, 80
specifications, 84
subsampling
color, 83
supported timings, 80
T
temporary image retention
avoiding, 4
definition, 4
timings, 80
TIR see temporary image retention
touchscreen
using the touchscreen, 69
troubleshooting, 93
during installation, 93
error codes in Planar UltraRes, 93
ii
Planar UltraRes Series User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising