Gefen | EXT-UHD600A-88 | Gefen EXT-UHD600A-88 Manual | Gefen EXT-UHD600A-88 4K Ultra HD 600 MHz 8x8 Matrix Manual

Gefen EXT-UHD600A-88 4K Ultra HD 600 MHz 8x8 Matrix Manual
*Preferred
600 MHz
4K ULTRA
8x8 Matrix
w/HDR and Audio De-Embedder
EXT-UHD600A-88
User Manual
Version A1
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open flame or excessive heat. Always dispose of used batteries
according to the instructions.
ii
Warranty Information
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Connect section of the Gefen Web site at http://www.gefen.com/connect/warranty-andreturn-policy
iii
Contacting Gefen Technical Support
Technical Support
(707) 283-5900
(800) 472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacific Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Core Brands, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
iv
Operating Notes
•
The information in this manual has been carefully checked and is believed to be
accurate. However, Gefen assumes no responsibility for any inaccuracies that may be
contained in this manual. In no event will Gefen be liable for direct, indirect, special,
incidental, or consequential damages resulting from any defect or omission in this
manual, even if advised of the possibility of such damages.
•
The technical information contained herein regarding the features and specifications is
subject to change without notice.
Important
Cable quality is critical when handling 600 MHz HDMI signals. It is highly
recommend that Gefen Locking HDMI cables, 10-foot or shorter, be used in
the installation. Gefen HDMI cables have been designed and tested to work at
600 MHz and reliably transport the full 18 Gbps throughput of HDMI 2.0.
© 2017 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Gefen® is a registered trademark of Core Brands, LLC.
Gefen and Core Brands, LLC reserve the right to make changes in the hardware, packaging, and any accompanying
documentation without prior written notice.
This product uses UL-Listed power supplies
v
Licensing
This product uses software that is subject to open source licenses, including one or more
of the General Public License Version 2 and Version 2.1, Lesser General Public License
Version 2.1 and Version 3, BSD, and BSD-style licenses. Distribution and use of this
product is subject to the license terms and limitations of liability provided in those licenses.
Specific license terms and Copyright Notifications are provided in the source code.
For three years from date of activation of this product, any party may request, and we
will supply, for software covered by an applicable license (e.g. GPL or LGPL), a complete
machine-readable copy of the corresponding open source code on a medium customarily
used for software interchange. The following software and libraries are included with this
product and subject to their respective open source licenses:
•
•
lwIP
jQuery
lwIP is licenced under the BSD licence:
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
3.
The name of the author may not be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS’’ AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
vi
Features and Packing List
Features*
•
Routes eight 4K sources to eight 4K displays
•
Supports resolutions up to 4K Cinema-DCI (4096 x 2160 up to 60 Hz, 4:4:4), 4K
Ultra HD (3860 x 2160 up to 60 Hz, 4:4:4) with HDR, 1080p Full HD, and WUXGA
(1920x1200)
•
Supports HDCP 2.2 and 1.4
•
Supports HDR (High Dynamic Range) 10-bit Deep Color at 4K 60 Hz 4:2:0 and 4K 24
Hz 4:4:4
•
Supports 12-bit Deep Color at 1080p Full HD (60 Hz 4:4:4)
•
3DTV pass-through
•
Lip Sync pass-through
•
EDID Management for rapid integration of source and displays
•
Supports uncompressed LPCM digital audio up to 7.1 channels
•
Supports up to 7.1 channels of HBR (High Bit Rate) digital audio including Dolby
Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™
•
Supports the use of DVI sources and DVI displays up to 1080p Full HD and WUXGA
(1920x1200), with Gefen CAB-DVI2-HDMI-LCK DVI-to-HDMI cables (not included)
•
Built-in Audio De-Embedders break out 2 channel analog, 2 channel PCM, and up
to 5.1 channels of Bitstream digital audio from each HDMI output, allowing the audio
content to be sent to external amplifiers and music distribution systems for added
impact.
•
Enhanced API facilitates added functionality with third-party control systems.
•
Easy-to-read, super-bright OLED front panel display indicates routing status and IP
settings
•
Locking power connector
•
Push button controls for Routing and Status
•
RS-232 Serial control interface for use with a third-party controller
•
IP control via Telnet, UDP, and the built-in web server interface
•
IR remote control
•
Gefen Syner-G™ software simplifies initial IP configuration and EDID Management
•
Field-updatable firmware via web server interface
•
2 U tall enclosure
•
Removable rack ears come pre-installed
•
Can be placed on a shelf or mounted in a standard 19-inch wide rack
* Features and specifications are subject to change without notice.
vii
Features and Packing List
Packing List
The 4K Ultra HD 600 MHz 8x8 Matrix w/ HDR and Audio De-Embedder ships with the
items listed below. If any of these items are not present in the box when you first open it,
immediately contact your reseller or Gefen Technical Support.
•
•
•
•
•
•
•
•
1 x 4K Ultra HD 600 MHz 8x8 Matrix
1 x 24V DC Power Supply (EXT-PS24U-O-6)
1 x AC Power Cord
4 x Self-Adhesive Rubber-Feet (pre-attached)
1 x IR Extender (EXT-RMT-EXTIRN)
1 x IR Remote (RMT-88A)
2 x AAA Batteries for the remote
1 x Quick-Start Guide
viii
Table of Contents
1
Getting Started
Introduction............................................................................................................ 2
Front Panel..................................................................................................... 2
Rear Panel..................................................................................................... 3
IR Remote Control......................................................................................... 5
Installing the Batteries.................................................................................... 8
Setting the IR Channel................................................................................... 9
Installation............................................................................................................ 10
Connection Instructions................................................................................ 10
Application Diagram..................................................................................... 11
Network Configuration using Syner-G.......................................................... 12
2
Basic Operation
Powering the Matrix............................................................................................. 16
Viewing the Routing Status.................................................................................. 17
Routing Inputs to Outputs.................................................................................... 18
Using the Front Panel.................................................................................. 18
Using the IR Remote Control....................................................................... 20
Adjusting the Output Volume................................................................................ 21
Muting and Unmuting Audio................................................................................. 23
Masking Outputs.................................................................................................. 25
Turning Off Inputs................................................................................................. 26
Locking the Matrix................................................................................................ 27
Using the IR Remote Control....................................................................... 28
Routing Presets.................................................................................................... 29
Using the Front Panel.................................................................................. 29
Using the IR Remote Control....................................................................... 30
Menu System....................................................................................................... 31
Accessing the Menu System........................................................................ 31
Audio Output Mode...................................................................................... 33
HPD Control................................................................................................. 35
HDCP Control.............................................................................................. 37
Setting the EDID Mode................................................................................ 40
IP Settings.................................................................................................... 43
TCP / Telnet Settings................................................................................... 48
Discovery Settings....................................................................................... 56
RS-232 Feedback........................................................................................ 58
Adjusting the LCM Brightness...................................................................... 60
Setting the Matrix IR Channel...................................................................... 62
Resetting the Matrix..................................................................................... 64
Rebooting the Matrix.................................................................................... 66
The Web Interface................................................................................................ 68
Introduction to the Web Interface................................................................. 68
Locking the Matrix........................................................................................ 73
Viewing the Routing Status.......................................................................... 74
ix
Table of Contents
Routing Inputs and Masking Outputs........................................................... 75
Routing Presets............................................................................................ 78
Input and Output Status............................................................................... 81
Changing Input and Output Names.............................................................. 82
Audio............................................................................................................ 83
HPD Control................................................................................................. 84
HDCP........................................................................................................... 85
Setting the EDID Mode................................................................................ 87
Copying EDID Data...................................................................................... 89
Getting EDID Information............................................................................. 91
Uploading and Downloading EDID Data...................................................... 92
Configuring Network Settings....................................................................... 95
System Settings......................................................................................... 101
3
Advanced Operation
Using Telnet, UDP, and RS-232..........................................................................112
Telnet Configuration................................................................................... 112
UDP Configuration..................................................................................... 112
RS-232 Configuration................................................................................. 113
Commands..........................................................................................................114
Discovery Service...................................................................................... 114
Input Status................................................................................................ 114
Manage EDID............................................................................................. 114
Network Settings........................................................................................ 115
Output Status............................................................................................. 116
Presets....................................................................................................... 116
Routing....................................................................................................... 116
Setup.......................................................................................................... 117
System Settings......................................................................................... 117
Volume....................................................................................................... 117
4
Appendix
Network Cable Diagram..................................................................................... 208
Default Settings.................................................................................................. 209
Internal EDID Profiles......................................................................................... 210
Specifications..................................................................................................... 215
Index.................................................................................................................. 217
x
This page left intentionally blank.
This page left intentionally blank.
600 MHz
4K ULTRA
8x8 Matrix
w/HDR and Audio De-Embedder
1
Getting Started
Introduction
Page Title
Getting Started
Front Panel
1
2
®
4
5
Menu
7
8
9
IR
Reset
Power
Preset
Enter
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Out A
L/R
Out B
3
L/R
L/R
Out C
Out D
In 3
In 4
6
L/R
Out E
L/R
Out F
L/R
Out G
Out H
ID
Name
1
Front panel display
2
Menu
Used to access the internal menu system.
See Accessing the Menu System (page
31) for more information.
3
Back
Press this button to step return to a previous
menu item.
4
▲, ▼, ◄, ►, Enter
Use the cursor buttons to select the desired
item within the menu system. Press the
Enter button to confirm the selection.
Accessing the Menu System (page 31) for
more information.
5
Preset
Press this button to select the desired Preset.
6
Lock
Press this button to lock the matrix. See
Locking the Matrix (page 73) for more
information.
7
IR
Receives signals from the included IR
remote control unit.
8
Reset
Press and hold this button for 10 seconds,
then release, to reset the matrix to factorydefault settings.
9
Power
Press this button to power-ON or Power-OFF
the matrix.
RS-232
Description
In 1
In 2
Displays matrix settings and feedback during
operation.
page | 2
In 5
In 6
In 7
In 8
24V DC
Introduction
Page Title
®
Menu
Preset
Getting Started
Rear Panel
Enter
IR
1
4
5
Back
Reset
Power
8
Lock
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
L/R
L/R
L/R
L/R
L/R
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 1
In 2
In 3
In 4
In 5
In 6
In 7
In 8
RS-232
2
L/R
Out A
3
6
7
24V DC
9
ID
Name
Description
1
IP Control
Connect an Ethernet cable between
this jack and a LAN. See Connection
Instructions (page 10) for more
information.
2
Grounding terminal
Connect a grounding wire (16 AWG or
greater) from this terminal to an approved
ground path.
3
IR In / Ext
Connect an IR extender (Gefen part no.
EXT-RMT-EXTIRN) or an electrical IR
cable from an automation system to this
port.
4
RS-232
Connect the RS-232 cable from this port
to an RS-232 device. See Connection
Instructions (page 10) for more
information.
5
Audio Outputs
Each HDMI output provides a three separate
ports for audio de-embedding: 1) L/R
(analog), 2) coax (digital), 3) TOSLINK®
(digital).
6
In (1 - 8)
Connect up to eight 4K Ultra HD source
devices to the matrix using these HDMI
ports.
7
Out (A - H)
Connect up to eight 4K Ultra HD displays to
the matrix using these HDMI ports.
page | 3
Getting Started
Introduction
ID
Name
Description
8
Cooling fan assembly
Provides active cooling for the matrix by
expelling warm air from the enclosure.
To prevent overheating, make sure this
vent is not blocked.
9
24V DC
Connect the included 24V DC power
supply to this power connector.
page | 4
Introduction
Power
2
BA
C
DC
D
Mute
Mute
E
FE
F
Volume
Volume
11
G
HG
Mask
H
Mask
10
Output
Output
Up
Menu
Menu
3
4
OK
Back
B
Preset
Preset
OK
Back
Lock
43
4
5
65
6
7
Input
87
Input
8
OFF
7
6
R03,1.5V
OFF
2
3
RMT-88A
Lock
Down
8
R03,1.5V
21
12
9
Up
Down
1
5
13
A
R03,1.5V
1
Power
R03,1.5V
Getting Started
IR Remote Control
ON
ON
1 2
1 2
15
14
RMT-88A
ID
Name
Description
1
Output buttons (A - H)
Press these buttons to select the desired
input when performing routing operations.
Each button corresponds to an Out port
(A - H) on the rear panel of the matrix.
2
Menu
Press this button to display the On-Screen
Menu.
3
▲, ▼, ◄, ►
Press these buttons to move around within
the front panel display.
4
Back
Press this button to return to a previous
menu item.
page | 5
Getting Started
Introduction
ID
Name
Description
5
Input buttons (1 - 8)
Press these buttons to select the desired
input when performing routing operations.
Each button corresponds to an In port
(1 - 8) on the rear panel of the matrix.
6
Off
Press this button to block an input.
See Turning Off Inputs (page 26) for
more information.
7
Lock
Press this button to toggle between locking
and unlocking the buttons on the front
panel.
8
OK
Press this button to accept the current
selection in the menu system.
9
Preset
Press this button to select the desired
preset. See Routing Presets (page 78)
for more information.
10
Mask
Press this button to mask the desired
output.
11
Volume
Adjusts the output volume on the selected
output. See Adjusting the Output Volume
(page 21) for more information.
12
Mute
Press this button to mute the audio on the
selected output. See Muting and Unmuting
Audio (page 23) for more information.
13
Power
Press this button to toggle power on the
matrix.
14
DIP switches
Sets the IR channel of the IR remote
control. In order for the IR remote control
to communicate with the matrix, both the
IR remote control and the matrix must be
set to the same IR channel. See Setting
the IR Channel (page 9) for information
on setting the IR channel of the IR remote
control. Use the front panel controls to set
the IR channel of the matrix. See Setting
the Matrix IR Channel (page 62) for
information on setting the IR channel of the
matrix.
page | 6
Getting Started
Introduction
ID
Name
Description
15
Battery compartment
(shown open)
Press this button to toggle between
locking and un Accepts two 1.5V AAAtype batteries. See Installing the Batteries
(page 8) for more information.
page | 7
Introduction
Getting Started
Installing the Batteries
1.
Remove the back cover the IR remote control unit.
2.
Insert two 1.5V AAA-type batteries, as shown, within the battery compartment.
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Up
Menu
Back
_
+
R03,1.5V
OK
R03,1.5V
Preset
Lock
Down
1
2
3
4
5
6
7
Input
8
OFF
_
+
ON
1 2
RMT-88A
3.
Replace the back cover.
Warning!
Risk of explosion if battery is replaced by an incorrect type. Dispose of used
batteries according to the instructions.
page | 8
R03,1.5
R03,1.5
Use the following DIP switch settings to set the IR channel of the IR remote control.
In order for the included IR remote control to communicate with the matrix, the IR remote
control must be set to the same channel as the matrix.
Channel 1 (default):
Channel 2:
ON
ON
1 2
1 2
DIP1 = OFF
DIP2 = OFF
DIP1 = ON
DIP2 = OFF
Channel 3:
Channel 4:
ON
ON
1 2
1 2
+
_
R03,1.5V
R03,1.5V
Getting Started
R03,1.5V
R03,1.5V
Setting the IR Channel
Introduction
DIP1 = OFF
DIP2 = ON
_
+
ON
1 2
DIP switches
page | 9
DIP1 = ON
DIP2 = ON
Getting Started
Installation
Connection Instructions
►► Video
1.
Connect an HDMI cable from each 4K Ultra HD source device to the In ports
(1 - 8) on the rear panel of the matrix. Up to eight source devices can be
connected.
2.
Connect a 4K Ultra HD display to each of the Out ports (A - H) on the rear panel
of the matrix. Up to eight displays can be connected.
►► Audio De-embedding
3.
The matrix provides one analog and two digital outputs for each HDMI output for audio
de-embedding:
a.
Connect a 3.5mm mini-stereo cable from each L/R port to an A/V receiver.
b.
Connect a RCA cable from each coax port to an A/V receiver.
c.
Connect an optical cable from each TOSLINK® port to an A/V receiver.
►► IP Control
4.
Connect a shielded CAT-5e (or better) cable from the IP Control port on the rear panel
of the matrix to the Local Area Network. See Network Configuration using Syner-G
(page 12) for more information on configuration.
►► RS-232 (optional)
5.
Connect a DB-9 cable from the RS-232 port on the rear panel of the matrix to the
automation device. See RS-232 Configuration (page 113) for more information.
►► IR Control (Optional)
6.
Connect an IR extender (Gefen part no. EXT-RMT-EXTIRN) or an electrical IR cable
from an automation system to the IR In / Ext port on the rear panel of the matrix.
Connecting an IR extender is useful if the IR sensor on the front panel will be hidden
from view.
►► Power
7.
Connect the included 24V DC power supply to the power connector on the matrix.
8.
Connect the AC power cord to the power supply and connect the power cord
to an available electrical outlet.
page | 10
Getting Started
Installation
Application Diagram
CAT-5
HDMI
DIGITAL AUDIO (TOSLINK®)
DIGITAL AUDIO (COAX)
ANALOG AUDIO (L/R)
USB
Automation
RS-232
Controller
with IR Out
IR IN
8x
8x
Power Amplifier
4K Ultra HD
Sources
8x
De-Embeddeed Audio
OR
EXT-RMT-EXTIRN
IR Extender
2x
Power Source for
Streaming Sources
Ultra HD 600 MHz 8x8 Matrix
w/HDR and Audio De-Embedder
LAN
(Web Interface,
Telnet, or UDP)
8x
Automation
Controller
with RS-232 Interface
4K Ultra HD
Displays
EXT-UHD600A-88
page | 11
Getting Started
Installation
Network Configuration using Syner-G
1.
Launch the Gefen Syner-G application.
Download the application here: http://www.gefen.com/support/download.jsp
2.
Select the matrix (EXT-UHD600A-88) from the list of products.
3.
Under the Device Settings section, select either Static or DHCP from the IP Mode
drop-down list.
►► Select Static to manual enter the IP address, subnet mask, and gateway IP.
Consult with your network administrator, if necessary.
►► Select DHCP to let the DHCP server automatically assign the IP address, subnet
mask, and gateway IP.
page | 12
Getting Started
Installation
4.
Click the Save button at the bottom of the screen.
5.
The matrix will automatically reboot and use the new network settings.
6.
Use the IP address of the matrix to access the built-in web interface or start a Telnet
session. See the following for more information:
►► The Web Interface (page 68)
►► Using Telnet, UDP, and RS-232 (page 112)
page | 13
This page left intentionally blank.
600 MHz
4K ULTRA
8x8 Matrix
w/HDR and Audio De-Embedder
2
Basic Operation
Use the Power button to power-on and power-off the matrix. The Power button is located
on the front panel of the matrix and on the IR remote control.
®
Menu
Preset
Enter
IR
1.
L/R
IR In/Ext
IP Control
L/R
A
B
C
D
RS-232
Mute
E
F
Volume
G
H
Mask
Connect the included power supply from the
power connector to an available electrical AC
outlet. The Power button will glow solid red,
indicating that the matrix is connected to an active
outlet. However, the matrix is not turned on.
L/R
Power
Out A
Out B
In 1
In 2
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
®
L/R
L/R
L/R
L/R
L/R
Out C
Out D
Out E
Out F
Out G
Out H
In 3
In 4
In 5
In 6
In 7
In 8
Menu
24V DC
Preset
Enter
IR
Output
Power
Lock
Back
Ultra
Menu
Reset
Up
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
HD 600 MHz
Preset 8x8 Matrix w/HDR and Audio De-Embedder
OK
EXT-UHD600A-88
Back
Lock
2.
L/R
L/R
Down
IR In/Ext
1
2
3
4
Out A
OFF
3.
RS-232
5
6
7
Input
8
In 1
Press the Power button on the front panel or on
the IR remote control.
L/R
Out B
In 2
L/R
Out C
L/R
R03,1.5V
IP Control
R03,1.5V
Basic Operation
Powering the Matrix
L/R
Out E
Out D
L/R
L/R
Out G
Out F
Out H
The Power button on the front panel will glow solid
blue to indicate that the matrix is powered.
In 3
®
In 4
In 5
Menu
In 7
In 6
24V DC
In 8
Preset
ON
1 2
Enter
IR
RMT-88A
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
The first piece of information that is displayed is the model and current firmware.
Be sure to check the Gefen website for the latest version of firmware.
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Out A
ext-uhdA600-88
v1.0
RS-232
4.
In 1
L/R
L/R
L/R
L/R
L/R
L/R
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
After a few moments, the routing screen will be displayed. The routing screen
represents the “home” screen from which the built-in menu system can be accessed.
out a :output a
A/V In:input 01
page | 16
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Power
Reset
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IR In/Ext
IP Control
A
B
C
D
In the example below, the source that is connected to In
1 is currently routed to the display (sink device) that is
connected to Out A.
L/R
Power
Out A
RS-232
In 1
L/R
L/R
L/R
L/R
L/R
Out C
Out D
Out E
Out F
Out G
Out H
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Mute
E
F
Volume
G
H
Mask
out A :output A
A/V In:input 01
®
Output
L/R
Out B
Menu
Preset
to display (sink) device
Up
Enter
IR
Menu
Preset
EXT-UHD600A-88
Lock
L/R
IP Control
Out A
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
L/R
IR In/Ext
Down
3
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Out A
OK
Back
Reset
Lock
Back
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
R03,1.5V
Basic Operation
Viewing the Routing Status
RS-232
In 1
L/R
L/R
L/R
L/R
L/R
L/R
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
In 1
from source device
ON
1 2
RMT-88A
Press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control to view each
output and which input is being received.
2.
The ▲ or ▼ buttons, on the front panel, will
momentarily glow blue when pressed, as shown
below:
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
L/R
L/R
Out A
Out B
Out C
In 1
In 2
In 3
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
page | 17
RS-232
In 4
24V DC
Basic Operation
Routing Inputs to Outputs
When the matrix is shipped from the factory, the matrix is set to “one-to-one” routing
mode. This means that Input 1 is routed to Output A, Input 2 is routed to Output B,
Input 3 is routed to Output C, and so on. To change the routing state for any output,
follow the instructions below.
Using the Front Panel
1.
Go to the routing screen. If the routing screen is not displayed, then press and
release the Back button until the routing screen is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
L/R
L/R
out B :output B
A/V In:input 02
IP Control
IR In/Ext
RS-232
2.
L/R
L/R
L/R
L/R
L/R
Out A
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 1
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Select the desired output by pressing and releasing the ▲ or ▼ buttons.
These buttons will glow blue when they are pressed.
Example: We have a 4K Ultra HD source connected to In 4 (Input 4)
and we want to view the source on the 4K Ultra HD display that is connected to Out G
(Output G).
The first thing we need to do is use the ▲ or ▼ buttons until Output G is
displayed. Currently, Input 7 is routed to Output G. We need to change it to
Input 4.
out G :output G
A/V In:input 07
3.
Press the Enter button.
4.
An arrow cursor will be displayed next to the input. This indicates that input
can now be changed.
out G :output G
>A/V In:input 07
page | 18
Basic Operation
Routing Inputs to Output
5.
Press and release the ▲ or ▼ buttons to select the desired input. In this
example, we will select Input 4.
out G :output G
>A/V In:input 04
6.
Once the desired input is selected, press the Enter button. The arrow cursor, next to
the input, will disappear indicating that the input can not be changed.
out G :output G
A/V In:input 04
7.
The selected input is now routed to the selected output.
8.
Repeat steps 2 - 6 to change the routing state for additional outputs.
page | 19
Routing Inputs to Output
Basic Operation
Using the IR Remote Control
Information
The front panel display will only show activity if a routing operation is being
performed on the output that is displayed. Otherwise, the routing operation is
performed in the background. To verify that the new routing state has been
executed, you can view the current routing state for that output. See Viewing
the Routing Status (page 17) for more information.
1.
Go to the routing screen. If the routing screen is not displayed, then press and
release the Back button on the IR remote control until the routing screen is displayed.
2.
Select the desired output by pressing one of the Output buttons (A - H) on the
top-portion of the IR remote control. In this example, we will route Input 5 to Output D.
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Output buttons
3.
Up
Menu
out D :output D
A/V In:input 02
Preset
OK
Lock
1
2
3
4
5
6
7
Input
8
OFF
The routing process is complete.
R03,1.5V
4.
Down
R03,1.5V
Back
Select the desired input by pressing one of the
Input buttons (1 - 8) on the lower-portion of the
IR remote control.
Down button
ON
1 2
RMT-88A
out D :output D
A/V In:input 05
page | 20
The output volume of each output can be adjusted from either the front panel, using the
included IR remote, or through the built-in web interface. In order to adjust the volume,
the audio output mode of the matrix must be set to variable. See Audio Output Mode (page
33) for more information.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
2.
Reset
Lock
Back
Press the Volume button on the IR remote control. The front panel display will prompt
for the output to be adjusted.
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Out A
VOLUME
SELECT OUTPUT
RS-232
In 1
L/R
L/R
L/R
L/R
L/R
L/R
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Output buttons
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Volume button
Up button
3.
Output
Up
Menu
Preset
Select the desired output by pressing the
desired Output button (A - H) on the
upper-portion of the IR remote control.
OK
Back
Lock
Down
2
3
4
5
6
7
Input
8
OFF
VOLUME A VOLUME: 87
PRESS UP OR DOWN
R03,1.5V
1
R03,1.5V
Basic Operation
Adjusting the Output Volume
Down button
ON
RMT-88A
4.
1 2
Press the Up or Down button to adjust the
volume for the selected output. Press the Up
button to increase the volume. Press the Down
button to decrease the volume.
page | 21
Basic Operation
Adjusting the Output Volume
Information
If the Down arrow button is pressed when the volume level is set to 0, then
the volume will be returned to 100. Similar behavior exists if the volume level
is set to 100 and the Up arrow is pressed: the volume level will be set to 0.
5.
Press the Back button to accept the volume setting for the selected output and return
to the Volume Select Output screen.
VOLUME
SELECT OUTPUT
Select another output using the Output buttons or press the Back button a second
time to return to the routing screen.
out B :output B
A/V In:input 02
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Back button
Up
Menu
Preset
OK
Back
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
R03,1.5V
6.
ON
1 2
RMT-88A
page | 22
The audio for each output can be muted from either the front panel, using the included IR
remote, or through the built-in web interface. The Mute button is used for both muting and
unmuting audio on the desired output.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
2.
Reset
Lock
Back
Press the Mute button on the IR remote control. The front panel display will prompt
for the output to be adjusted.
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Out A
MUTE
SELECT OUTPUT
RS-232
In 1
L/R
L/R
L/R
L/R
L/R
L/R
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 2
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Output buttons
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Up
Menu
Preset
Mute button
3.
Select the desired output by pressing the
desired Output button (A - H) on the
upper-portion of the IR remote control.
If the output is not muted, then the following
screen will be displayed:
OK
Back
Lock
Down
2
3
4
5
6
7
Input
8
OFF
MUTE: OUTPUT B NAME
PRESS MUTE to MUTE
R03,1.5V
1
R03,1.5V
Basic Operation
Muting and Unmuting Audio
If the output is muted, then the following screen
will be displayed:
ON
1 2
RMT-88A
MUTE: OUTPUT B NAME
PRESS MUTE to UNMUTE
page | 23
5.
Press the Back button to accept the volume setting for the selected output and return
to the Mute Select Output screen.
MUTE
SELECT OUTPUT
6.
Select another output using the Output buttons or press the Back button a second
time to return to the routing screen.
out B :output B
A/V In:input 02
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Back button
Up
Menu
Preset
OK
Back
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
R03,1.5V
Basic Operation
Muting and Unmuting Audio
ON
1 2
RMT-88A
page | 24
When masking outputs through the front panel, the IR remote control must be used.
Outputs can also be masked by by using the built-in web interface. See Routing Inputs and
Masking Outputs (page 75) for more information.
When an output is masked, the signal is blocked at the output. Let’s say Input 02
is routed to Output A, Output B, and Output C. If we mask Output B, then only A/V
signal on Output B will be blocked. Output A and Output C will remain unaffected.
1.
Start from any screen. In this example, we are starting at the routing screen.
out B :output B
A/V In:input 02
Output buttons
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
2.
Press the Mask button on the IR remote control.
3.
Select the desired output by pressing one of the
Output buttons (A - H) on the top-portion of the IR
remote control.
Up
Menu
Preset
Mask button
OK
Back
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
R03,1.5V
Basic Operation
Masking Outputs
4.
The selected output will be masked immediately.
5.
To unmask the the desired output, repeat steps 2
and 3.
ON
1 2
RMT-88A
Information
When an output is masked, no feedback will be shown on the front-panel
display. However, the built-in web interface will always reflect a masking
change.
page | 25
Turning off an input simulates a source that is not present.
Setting an input to the OFF state can only be performed through the IR remote control or
the built-in web interface. See Routing Inputs to Outputs (page 18) for more information.
1.
Starting from any screen, press the button of the output (Local, A - H), on the
top-portion of the IR remote control, where the Input is routed.
For example, if we want to “block” Input 3, and Input 3 is routed to Output H,
then we would press the H button.
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
Output
Up
Menu
Output buttons
2.
Press the Off button on the IR remote control.
3.
The selected input will be turned “off” immediately.
4.
The front-panel display will show the change:
Preset
OK
Back
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
out H :output H
A/V In:off
R03,1.5V
Basic Operation
Turning Off Inputs
Off button
ON
1 2
RMT-88A
In order for an input, on the matrix, to be turned
“off”, a source device must be connected to the
input.
Input buttons
5.
To “unblock” an input, press the desired Output button (A - H) then select an input
from the Input buttons, located at the bottom-portion of the IR remote control.
page | 26
Basic Operation
Locking the Matrix
To prevent an accidental routing change or power-down (by pressing the Power button),
the front-panel buttons on the matrix can be locked. Locking the matrix disables the
front-panel controls, IR, and the built-in web interface.
►► Locking the Matrix
1.
Starting from any screen, press and hold the Lock button.
2.
The Lock button will flash blue six times and then glow solid blue.
3.
Release the Lock button.
4.
The matrix is now locked.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
►► Unlocking the Matrix
IP Control
IR In/Ext
L/R
Out A
L/R
L/R
Out B
L/R
Out C
L/R
Out E
Out D
L/R
Out F
L/R
Out G
Out H
In 7
In 8
1.
To unlock the matrix, press and hold the Lock button.
2.
The Lock button will flash six times and then will be no longer illuminated.
3.
The matrix is now unlocked.
RS-232
In 1
In 3
In 2
®
In 4
In 5
Menu
In 6
24V DC
Preset
out a :output a
A/V In:input 01
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
RS-232
L/R
L/R
L/R
L/R
L/R
L/R
L/R
Out A
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 1
In 2
In 3
In 4
In 5
In 6
In 7
In 8
page | 27
24V DC
Using the IR Remote Control
►► Locking the Matrix
1.
Starting from any screen, press the Lock button on the IR remote control.
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
2.
The Lock button on the front panel will glow solid
blue.
3.
The matrix is now locked.
®
Menu
Preset
Enter
IR
Output
Power
Lock
Back
Ultra
Menu
Reset
Up
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
HD 600 MHz
Preset 8x8 Matrix w/HDR and Audio De-Embedder
OK
EXT-UHD600A-88
Back
Lock
L/R
L/R
Down
1
2
3
4
5
6
7
Input
8
Out A
L/R
L/R
Out B
Out C
OFF
1.
RS-232
L/R
L/R
►► Unlocking the Matrix
In 1
In 3
In 2
2.
Out D
R03,1.5V
IR In/Ext
IP Control
R03,1.5V
Basic Operation
Locking the Matrix
Out E
L/R
L/R
Out G
Out F
Out H
To unlock the matrix, press the Lock button
on the IR remote control.
In 4
In 5
In 7
In 6
24V DC
In 8
The Lock button, on the front panel, will be no
longer illuminated.
ON
1 2
3.
RMT-88A
®
The matrix is now unlocked.
Menu
Preset
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
RS-232
L/R
L/R
L/R
L/R
L/R
L/R
L/R
Out A
Out B
Out C
Out D
Out E
Out F
Out G
Out H
In 1
In 2
In 3
In 4
In 5
In 6
In 7
In 8
page | 28
24V DC
Basic Operation
Routing Presets
Routing presets can be recalled using the front panel buttons or the IR remote control.
For information on creating presets, see Routing Presets (page 29).
Using the Front Panel
1.
Start from any screen.
2.
Press the Preset button on the front panel. The Preset button, on the front panel,
will flash blue when pressed.
®
Menu
Preset
preset: 1
name: preset_01
Enter
IR
The Preset selection screen will be displayed.
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Out A
L/R
Out B
preset: 1
name: preset_01
RS-232
4.
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
3.
Reset
Lock
Back
In 1
In 2
L/R
L/R
L/R
L/R
L/R
Out C
Out D
Out E
Out F
Out G
Out H
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Select the desired preset by pressing and releasing the ▲ or ▼ buttons on the front
panel.
preset: 3
name: preset_03
5.
Once the desired preset is selected, press the Enter button on the front panel to load
the preset.
preset 3: preset_03
set
6.
The preset is now loaded and the routing state, stored in the preset, will be
applied to the matrix.
7.
After a few moments, the routing screen will be displayed.
out D :output D
A/V In:input 02
page | 29
Using the IR Remote Control
1.
Start from any screen.
2.
Press the Preset button on the IR remote control.
3.
Power
Power
A
A
BB
C
C
D
D
Mute
Mute
EE
FF
Volume
Volume
G
G
H
H
Mask
Mask
Output
Output
Only Presets 1 - 8 can be selected, when using
the IR remote control.
4.
Up
Up
Menu
Menu
Use the set of Input buttons, from the bottomportion of the IR remote control to select the
desired preset.
The preset is now loaded and the routing state,
stored in the preset, will be applied to the matrix.
Preset
Preset
OK
OK
Back
Back
Preset button
Lock
Lock
11
22
33
44
55
66
77
Input
Input
88
OFF
OFF
R03,1.5V
R03,1.5V
Down
Down
R03,1.5V
R03,1.5V
Basic Operation
Routing Presets
Input buttons
ON
ON
11 22
RMT-88A
RMT-88A
Information
When using the IR remote control, no confirmation will be shown in the front
panel display.
page | 30
Accessing the Menu System
The front-panel menu system provides the ability to locally control many of the matrix
features. However, we recommend using the built-in Web interface to control the matrix.
For more information on accessing the web interface, see The Web Interface (page 68).
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Power
Lock
Back
4K Ultra HD 8x8 Matrix for HDMI w/ HDCP 2.2
EXT-UHD-88
Power
IP Control
A
B
IR In/Ext
Out A
C
D
Mute
E
F
Volume
G
H
Mask
RS-232
Output
In 1
Out B
2.
Up
Menu
In 2
out B :output B
A/V In:input 02
Out C
Out D
Out E
Out F
Out G
Out H
Press and release the Menu button on the front
panel or on the IR remote control. The Menu
button will momentarily flash blue when it is
pressed.
In 3
In 4
In 5
In 6
In 7
In 8
24V DC
Preset
®
Menu
Preset
OK
Back
Lock
Enter
IR
Down
Back
4K Ultra HD 8x8 Matrix for HDMI w/ HDCP 2.2
1
2
3
4
5
OFF
3.
6
R03,1.5V
R03,1.5V
Basic Operation
Menu System
Power
Lock
The Setup menu will be displayed:
EXT-UHD-88
7
Input
8
ON
IP Control
IR In/Ext
Out A
Out B
In 1
In 2
setup
Out C
1 2
Out D
Out E
Out F
Out G
Out H
In 4
In 5
In 6
In 7
In 8
RMT-88A
RS-232
In 3
24V DC
There are four menu systems: Setup, EDID
Management, Network, and System. The Setup
menu will always be the first menu to be displayed,
when entering the menu system.
4.
Press and release the ▲ or ▼ buttons to select the desired menu. These buttons
will glow blue when they are pressed.
page | 31
Basic Operation
Menu System
5.
The top-level menu system has the following order:
setup
edid management
network
system
6.
To return to the routing screen, press the Back button on the front panel or on the IR
remote control until the routing screen is displayed.
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
L/R
Information
Out A
L/R
Out B
L/R
Out C
L/R
Out D
L/R
Out E
L/R
Out F
L/R
Out G
Out H
Depending upon the location within the menu system, multiple presses of the
Back button may be required in order to return to the routing screen.
RS-232
In 1
In 2
In 3
In 4
page | 32
In 5
In 6
In 7
In 8
24V DC
Audio Output Mode
This menu option allows the audio output to be set to either variable or fixed. If set to
fixed, then the matrix will control the audio output. If set to var (variable), then the output
volume will be controlled by the source.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
out A :output A
A/V In:input 01
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
RS-232
Output
L/R
Preset
OK
Back
Out B
In 1
In 2
L/R
Out C
L/R
Out D
setup
In 3
In 4
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
24V DC
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
The Audio Output Mode option will be displayed:
Lock
AUDIO OUTPUT MODE
OUTPUT A NAME: VAR
Down
2
3
4
5
6
7
Input
8
OFF
6.
R03,1.5V
1
L/R
Out A
Up
Menu
The Setup menu will be displayed:
3.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
R03,1.5V
Basic Operation
Menu System
Press and release the ▲ or ▼ buttons on the
front panel or on the included IR remote control, to
select the desired output.
ON
1 2
RMT-88A
page | 33
Basic Operation
Menu System
7.
Once the desired output is selected, press the Enter button on the front panel or the
OK button on the IR remote control. The arrow cursor will appear next to the current
selection for the output.
AUDIO OUTPUT MODE
>OUTPUT C NAME: VAR
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired setting.
AUDIO OUTPUT MODE
>OUTPUT C NAME: FIXED
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to save the setting.
10. To set the volume control on a different output, press the Back button on the front
panel or on the IR remote control, then repeat steps 6 - 8.
11. To return to the routing screen, press the Back button twice.
page | 34
HPD Control
This menu option allows an HPD (Hot-Plug Detect) pulse to be sent to the selected input.
Sending an HPD pulse to an input is equivalent to disconnecting and reconnecting the
video cable at the source.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
out A :output A
A/V In:input 01
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
RS-232
Output
L/R
Preset
OK
Back
Out B
In 1
In 2
L/R
Out C
L/R
Out D
setup
In 3
In 4
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
24V DC
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
The HPD Control option will be displayed:
Lock
setup:
HDP control
Down
2
3
4
5
6
7
Input
8
OFF
6.
R03,1.5V
1
L/R
Out A
Up
Menu
The Setup menu will be displayed:
3.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
R03,1.5V
Basic Operation
Menu System
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
ON
1 2
RMT-88A
page | 35
Basic Operation
Menu System
7.
The input selection screen will be displayed. Input 01 will be displayed, by default.
hdp control:
pulse: input 01
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired input. These buttons will glow blue when they are pressed on the
front panel.
9.
After selecting the desired input, press the Enter button on the front panel. If using
the included IR remote control, press the OK button.
hdp pulsed for input
input 05
10. The HPD pulse will be sent to the selected input. If a display is connected to the
output to which the input is routed, then the display will flash as the HPD pulse is
received.
11. After a few moments, the input selection screen will be displayed again:
hdp control:
pulse: input 05
12. To send an HPD pulse to another input, repeat steps 4 - 7.
13. To return to the HPD Control option, press the Back button on the front panel or on
the IR remote control.
14. To return to the routing screen, press the Back button two more times.
page | 36
HDCP Control
This menu option restricts the version of HDCP that is accepted by an input. This matrix
supports up to HDCP 2.2.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
IR In/Ext
The Setup menu will be displayed:
2.
L/R
IP Control
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
RS-232
Output
Preset
In 3
In 4
24V DC
3.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
4.
The HPD Control option will be displayed:
Up
Menu
setup
OK
Back
Lock
setup:
HDP control
Down
2
3
4
5
6
7
Input
8
OFF
5.
R03,1.5V
1
R03,1.5V
Basic Operation
Menu System
Press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control, to select the
HDCP Control option:
ON
1 2
RMT-88A
setup:
hdcp control
6.
Press the Enter button on the front panel or on the IR remote control to display the
input control screen.
page | 37
Basic Operation
Menu System
7.
Press the Enter button on the front panel or on the IR remote control to display the
input control screen.
hdcp control: input
input 01: 2.2
8.
Press and release the ▲ or ▼ buttons on the front panel or on the included IR
remote control, to select the desired input or output. These buttons will glow blue
when they are pressed on the front panel.
hdcp control: input
input 03: 2.2
9.
Press the Enter button on the front panel. If using the included IR remote control,
press the OK button.
If an input (1 - 8) is selected, then the following options will be available:
►► 2.2 and below
Only HDCP version 2.2 and below is allowed to be sent from the source device.
►► 1.4 and below
Only HDCP version 1.4 and below is allowed to be sent from the source device.
►► Reject
Blocks HDCP content from being sent from the source device.
If an output (A - H) is selected, then the following options will be available:
►► Follow Input
HDCP pass-through: The content on the output of the matrix matches the
content provided by the source device.
►► Always Encode
Always applies HDCP encryption to the content on the output of the matrix.
So, even if the source is not HDCP, the output will be HDCP.
10. Once the desired input or output is selected, press the Enter button on the front
panel or the OK button on the IR remote control. The arrow cursor will appear next
to the current selection for the input (or output).
input 03
>2.2 and below
page | 38
Basic Operation
Menu System
11. Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired setting.
input 03
>1.4 and below
12. Press the Enter button on the front panel or the OK button on the IR remote control
to save the setting.
input 03
1.4 and below
13. To set the HDCP control on a different input or output, press the Back button on the
front panel or on the IR remote control.
14. To return to the HPD Control option, press the Back button on the front panel or on
the IR remote control.
15. To return to the routing screen, press the Back button two more times.
page | 39
Setting the EDID Mode
This menu option allows the EDID that will be used by the source that is connected to each
input. Internal, external, or a custom EDID can be selected.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
RS-232
Output
The Setup menu will be displayed:
2.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
3.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control,
to select the EDID Management menu:
Preset
OK
EDID management
Back
Lock
Down
2
3
4
5
6
7
Input
8
OFF
R03,1.5V
1
R03,1.5V
Basic Operation
Menu System
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
The EDID Mode menu will be displayed:
ON
1 2
RMT-88A
edid mode
page | 40
Basic Operation
Menu System
6.
Press the Enter button on the front panel or on the IR remote control to display the
input control screen. Input 01 will be displayed by default.
edid mode
input 01
7.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired input.
edid mode
input 05
8.
Press the Enter button on the front panel. If using the included IR remote control,
press the OK button.
9.
The EDID selection screen will be displayed. The current EDID, for the selected
input, will be displayed. An arrow cursor will be displayed next to the current EDID,
indicating that it can be changed.
edid: input 05
>1080P 2CH
10. Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired EDID. See Internal EDID Profiles (page 210) for details on
internal EDID specifications.
The available EDID options, for each input, are:
EDID
Description
UHD 4K 600 MHz 2Ch
UHD 4K 600 Mhz with 2-channel audio
UHD 4K 600 MHz Multi
UHD 4K 600 Mhz with multichannel audio
UHD 4K 300 MHz 2Ch
UHD 4K 300 Mhz with 2-channel audio
UHD 4K 300 MHz Multi
UHD 4K 300 Mhz with multichannel audio
1080P 2Ch
1080p with 2-channel audio
1080P Multi
1080p with multichannel audio
External
Uses EDID of downstream sink
Custom - User
Uses a custom EDID
See Setting the EDID Mode (page 87) for more information on using the Custom setting.
page | 41
Basic Operation
Menu System
11. Once the desired EDID has been selected, press the Enter button on the front
panel or the OK button on the IR remote control. The input selection screen will
be displayed.
edid mode
input 05
12. To set the EDID on another input, repeat steps 7 - 11.
13. Press the Back button on the front panel or on the IR remote control to return
to the EDID Mode menu.
14. To return to the routing screen, press the Back button two more times.
page | 42
IP Settings
Use this menu option to set the IP mode, IP address, subnet mask, gateway, and HTTP
port of the matrix.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
IR In/Ext
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
RS-232
Output
The Setup menu will be displayed:
2.
L/R
IP Control
3.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the Network menu:
Preset
OK
network
Back
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
R03,1.5V
Basic Operation
Menu System
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
The IP Settings menu will be displayed:
ON
1 2
RMT-88A
ip settings
6.
Press the Enter button on the front panel or the OK button on the IR remote control
to display the IP Mode screen. The current network mode will be displayed.
page | 43
Basic Operation
Menu System
►► Setting the IP Mode
a.
From the IP Mode screen, press the Enter button on the front panel or the OK
button on the IR remote control. An arrow cursor will be displayed next to the
current IP mode, indicating that it can be changed:
ip mode:
>static
b.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote
control, to select the desired IP Mode.
►► Static mode
Allows custom configuration of the IP address, subnet mask, and gateway.
►► DHCP mode
The IP address, subnet mask, and gateway address are automatically
assigned by a DHCP server.
c.
Press the Enter button on the front panel or the OK button on the IR remote
control to save the change.
d.
Reboot the matrix to affect changes.
►► Setting the IP Address
a.
From the IP Mode screen, press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control, to select the IP Address option.
The current IP address will be displayed.
ip address
192.168.001.072
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the IP address.
Important
The IP address can only be changed if the IP Mode is set to Static.
c.
The cursor will appear under the first digit of the IP address.
ip address
192.168.001.072
_
page | 44
Basic Operation
Menu System
d.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
ip address:
092.168.001.072
_
e.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the IP address.
f.
After the desired IP address has been set, press the Enter button on the front
panel or the OK button on the IR remote control to save the change.
ip address:
010.005.064.001
g.
Reboot the matrix to affect changes.
►► Setting the Subnet Mask
a.
From the IP Mode screen, press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control, to select the Subnet Mask option. The current
subnet mask will be displayed.
\
b.
subnet mask:
255.255.255.000
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the IP address.
Important
The subnet mask can only be changed if the IP Mode is set to Static.
c.
The cursor will appear under the first digit of the address.
subnet mask:
255.255.255.000
_
d.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between
each digit in the address.
_
page | 45
Basic Operation
Menu System
a.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
subnet mask:
255.255.055.000
_
b.
After the desired address has been set, press the Enter button on the front panel
or the OK button on the IR remote control to save the change.
subnet mask:
255.255.000.000
c.
Reboot the matrix to affect changes.
►► Setting the Gateway
a.
From the IP Mode screen, press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control, to select the Gateway option.
The current gateway address will be displayed.
\
b.
gateway:
192.168.001.001
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the address.
Important
The gateway address can only be changed if the IP Mode is set to Static.
c.
The cursor will appear under the first digit of the address.
gateway:
192.168.001.001
_
d.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
gateway:
092.168.001.001
_
page | 46
Basic Operation
Menu System
e.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the IP address.
f.
After the desired IP address has been set, press the Enter button on the front
panel or the OK button on the IR remote control to save the change.
gateway:
010.005.064.001
g.
Reboot the matrix to affect changes.
►► Setting the HTTP Listening Port
a.
From the IP Mode screen, press and release the ▲ or ▼ buttons on the front
panel or on the IR remote control, to select the HTTP Port option.
The current HTTP port will be displayed.
WEB port:
80
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the port number. The cursor will appear under the first digit
of the port number.
WEB port:
00080
_
c.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
d.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the port number.
e.
After the desired address has been set, press the Enter button on the front panel
or the OK button on the IR remote control to save the change.
WEB port:
81
f.
Reboot the matrix to affect changes.
page | 47
TCP / Telnet Settings
Use this menu option to set TCP access, the TCP port, Telnet welcome message state,
and enabling / disabling of password credentials.
1.
Go to the routing screen. If the routing screen is not displayed, then press
the Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
IR In/Ext
Power
A
B
C
D
Mute
E
F
Volume
G
H
Mask
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
RS-232
Output
The Setup menu will be displayed:
2.
L/R
IP Control
3.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select
the Network menu:
Preset
OK
Back
network
Lock
Down
2
4
5
6
7
Input
8
OFF
R03,1.5V
1
3
R03,1.5V
Basic Operation
Menu System
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
Press the ▲ or ▼ buttons on the front panel or on
the IR remote control to select the TCP / Telnet
Settings menu.
ON
1 2
RMT-88A
tcp/telnet settings
6.
Press the Enter button on the front panel or the OK button on the IR remote control
to display the TCP access screen. The current setting will be displayed.
page | 48
Basic Operation
Menu System
►► Enabling / Disabling TCP (Telnet) Access
a.
From the TCP access screen, press the Enter button on the front panel or the
OK button on the IR remote control.
tcp access:
enabled
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. An arrow cursor will be displayed next to
the current setting, indicating that it can be changed:
tcp access:
>enabled
c.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote
control, to select the desired setting.
►► Enabled
Allows Telnet sessions to the matrix.
►► Disabled
Disables Telnet sessions to the matrix.
tcp access:
>disabled
d.
Press the Enter button on the front panel or the OK button on the IR remote
control to save the change.
tcp access:
disabled
e.
Reboot the matrix to affect changes.
page | 49
Basic Operation
Menu System
►► Setting the TCP Listening Port
a.
From the TCP access screen, press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select the TCP Port option.
The current TCP port will be displayed.
tcp port:
23
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the port number. The cursor will appear under the first digit
of the port number.
tcp port:
00023
_
c.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the port number.
d.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
tcp port:
00023
_
e.
After the desired port number has been set, press the Enter button on the front
panel or the OK button on the IR remote control to save the change.
tcp port:
00024
f.
Reboot the matrix to affect changes.
page | 50
Basic Operation
Menu System
►► Enabling / Disabling Telnet Welcome Message
a.
From the TCP access screen, press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select the Telnet Welcome option.
The current setting will be displayed. The default setting is show.
TELNET WELCOME:
SHOW
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
TELNET WELCOME
>SHOW
c.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote
control, to select the desired setting.
►► Show
Shows the welcome message at the beginning of each Telnet session.
►► Hide
Hides the welcome message for Telnet sessions.
TELNET WELCOME
>HIDE
d.
Press the Enter button on the front panel or the OK button on the IR remote
control to save the change.
TELNET WELCOME
HIDE
e.
Reboot the matrix to affect changes.
page | 51
Basic Operation
Menu System
►► Enabling / Disabling UDP Access
a.
From the UDP access screen, press the Enter button on the front panel or the
OK button on the IR remote control. An arrow cursor will be displayed next to
the current setting, indicating that it can be changed:
UDP access:
disabled
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
udp access:
>disabled
c.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote
control, to select the desired setting.
►► Enabled
Allows the UDP protocol to be used with the matrix.
►► Disabled
Prevents the UDP protocol from being used with the matrix.
udp access:
>enabled
d.
Press the Enter button on the front panel or the OK button on the IR remote
control to save the change.
udp access:
enabled
e.
Reboot the matrix to affect changes.
page | 52
Basic Operation
Menu System
►► Setting the UDP Listening Port
a.
From the UDP Access screen, press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select the UDP Port option.
The current UDP port will be displayed.
Udp port:
50007
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the port number. The cursor will appear under the first digit
of the port number.
udp port:
50007
_
c.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the port number.
d.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
udp port:
50009
_
e.
After the desired port number has been set, press the Enter button on the front
panel or the OK button on the IR remote control to save the change.
udp port:
50009
f.
Reboot the matrix to affect changes.
page | 53
Basic Operation
Menu System
►► Enabling / Disabling Remote UDP Access
a.
From the UDP Access screen, press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select the Remote UDP
Access option. The current setting will be displayed.
remote UDP access:
disabled
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
remote udp access:
>disabled
c.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote
control, to select the desired setting.
►► Enabled
Allows the Remote UDP protocol to be used with the matrix.
►► Disabled
Prevents the Remote UDP protocol from being used with the matrix.
remote udp access:
>enabled
d.
Press the Enter button on the front panel or the OK button on the IR remote
control to save the change.
remote udp access:
enabled
e.
Reboot the matrix to affect changes.
page | 54
Basic Operation
Menu System
►► Setting the Remote UDP Address
a.
From the UDP Access screen, press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control, to select the Remote UDP
Address option. The current UDP address will be displayed.
remote UDP address:
192.168.001.255
b.
Press the Enter button on the front panel or the OK button on the IR remote
control to edit the IP address.
c.
The cursor will appear under the first digit of the UDP address.
remote UDP address:
192.168.001.255
_
d.
Press the ▲ or ▼ buttons on the front panel or on the IR remote control,
to change the numerical value of the digit (0 - 9).
remote UDP address:
192.168.001.155
_
e.
Press the ◄ or ► buttons on the front panel or on the IR remote control to move
between each digit in the IP address.
f.
After the desired UDP address has been set, press the Enter button on the front
panel or the OK button on the IR remote control to save the change.
remote UDP address:
192.168.001.155
g.
Reboot the matrix to affect changes.
page | 55
Discovery Settings
Use this menu option to enable / disable the “discovery” feature.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
B
C
D
Mute
E
F
Volume
G
H
Mask
RS-232
Output
L/R
Out A
L/R
Out B
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
A
In 1
In 2
3.
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the Network menu:
Up
Menu
Preset
network
OK
Back
Lock
Down
2
3
4
5
6
7
Input
8
OFF
R03,1.5V
1
The Setup menu will be displayed:
2.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
R03,1.5V
Basic Operation
Menu System
4.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
5.
Press the ▲ or ▼ buttons on the front panel or
on the IR remote control to select the Discovery
Settings menu.
ON
1 2
RMT-88A
discovery settings
6.
Press the Enter button on the front panel or the OK button on the IR remote control
to display the Discovery screen. The current setting will be displayed.
page | 56
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
discovery:
)enabled
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired setting.
►► Enabled
Allows the matrix to be “discovered”, when connected to a network, by the
Syner-G Software Suite.
►► Disabled
Prevents the matrix from being “discovered” by the Syner-G Software Suite.
discovery:
)disabled
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to save the change.
discovery:
disabled
10. Reboot the matrix to affect changes.
page | 57
RS-232 Feedback
Use this menu option to enable / disable RS-232 feedback. When disabled, RS-232
commands will be executed but will not provide a response.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
B
C
D
Mute
E
F
Volume
L/R
G
H
Mask
L/R
Out B
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
RS-232
Output
L/R
Out A
A
In 1
In 2
4.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the System menu:
Preset
OK
System
Back
Lock
Down
2
3
4
5
6
7
Input
8
OFF
R03,1.5V
1
The Setup menu will be displayed:
3.
Power
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
R03,1.5V
Basic Operation
Menu System
5.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
6.
Press the ▲ or ▼ buttons on the front panel or
on the IR remote control to select the RS-232
Feedback menu.
ON
RMT-88A
1 2
The current setting will be displayed.
RS-232 feedback:
enabled
page | 58
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
rs-232 feedback:
)Enabled
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired setting.
►► Enabled
RS-232 commands are executed and a response is sent back to the automation
device.
►► Disabled
RS-232 commands are executed but no response is provided.
rs-232 feedback:
)Disabled
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to save the change.
rs-232 feedback:
disabled
10. Reboot the matrix to affect changes.
page | 59
Adjusting the LCM Brightness
Use this menu option to change the brightness of the front panel LCM display.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
A
IR In/Ext
Power
L/R
L/R
Out A
Out B
In 1
In 2
RS-232
D
Mute
E
F
Volume
G
H
Mask
Output
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
B
C
4.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the System menu:
Preset
System
OK
Back
Lock
Down
2
3
4
5
6
7
Input
8
RMT-88A
OFF
R03,1.5V
1
The Setup menu will be displayed:
3.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
R03,1.5V
Basic Operation
Menu System
5.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
6.
Press the ▲ or ▼ buttons on the front panel
or on the IR remote control to select the LCD
Brightness menu.
ON
1 2
The current setting will be displayed.
lcd brightness:
60
page | 60
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current setting. The cursor will appear next to the current
setting.
lcd brightness:
)60
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired setting. The range is from 0 to 100 and can be adjusted by
increments of 1.
lcd brightness:
)70
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to save the change.
lcd brightness:
70
10. Reboot the matrix to affect changes.
page | 61
Setting the Matrix IR Channel
Use this menu option to set the IR channel of the matrix. In order for the included IR
remote to work with the matrix, both the matrix and the IR remote control must be set
to the same IR channel. See Setting the IR Channel (page 9) for more information on
setting the IR channel for the IR remote control.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
A
B
C
D
RS-232
Mute
E
F
Volume
G
H
Mask
Output
The Setup menu will be displayed:
3.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
4.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the System menu:
Preset
System
OK
Back
Lock
Down
2
3
4
5
6
7
Input
8
RMT-88A
OFF
R03,1.5V
1
R03,1.5V
Basic Operation
Menu System
5.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
6.
Press the ▲ or ▼ buttons on the front panel
or on the IR remote control to select the IR
Channel menu.
ON
1 2
The current IR channel will be displayed.
page | 62
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control to change the current IR channel. The cursor will appear next to the
current IR channel.
IR CHANNEL:
)1
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select the desired IR channel. The IR channel range is 1 - 4.
ir channel:
)2
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to save the change.
ir channel:
2
10. Reboot the matrix to affect changes.
page | 63
Resetting the Matrix
Use this menu option to reset the matrix to factory-default settings. See Default Settings
(page 209) for more information on these settings.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
IR In/Ext
Power
L/R
L/R
Out A
Out B
In 1
In 2
L/R
Out C
L/R
Out D
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
setup
A
B
C
D
RS-232
Mute
E
F
Volume
G
H
Mask
Output
The Setup menu will be displayed:
3.
L/R
IP Control
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
Reset
Lock
Back
4.
Up
Menu
In 3
In 4
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the System menu:
Preset
System
OK
Back
Lock
Down
2
4
5
6
7
Input
8
RMT-88A
OFF
R03,1.5V
1
3
R03,1.5V
Basic Operation
Menu System
5.
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
6.
Press the ▲ or ▼ buttons on the front panel
or on the IR remote control to select the Factory
Reset menu.
ON
1 2
factory reset
page | 64
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control. The matrix will prompt to confirm the factory-reset operation.
factory reset
)yes
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select either Yes or No.
factory reset
)no
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to confirm the selection.
If Yes is selected, then the matrix will be reset to factory-default settings and will
automatically be rebooted.
page | 65
Rebooting the Matrix
Use this menu option to reboot the matrix.
1.
Go to the routing screen. If the routing screen is not displayed, then press the
Back button on the front panel or on the IR remote control until the routing screen
is displayed.
2.
Press and release the Menu button on the front panel or on the IR remote control.
The Menu button, on the front panel, will momentarily flash blue when it is pressed.
®
Menu
Preset
SETUP
Enter
IR
Reset
Power
Lock
Back
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
EXT-UHD600A-88
L/R
IP Control
IR In/Ext
Power
A
B
C
D
RS-232
Mute
E
F
Volume
G
H
Mask
Output
3.
L/R
Out A
In 1
In 2
4.
Up
Menu
The Setup menu will be displayed:
L/R
Out B
L/R
Out C
L/R
Out D
setup
In 3
In 4
L/R
L/R
L/R
Out E
Out F
Out G
Out H
In 5
In 6
In 7
In 8
24V DC
Press and release the ▲ or ▼ buttons on the
front panel or on the IR remote control,
to select the System menu:
Preset
OK
Back
System
Lock
Down
2
3
4
5
6
7
Input
8
OFF
5.
R03,1.5V
1
R03,1.5V
Basic Operation
Menu System
Press the Enter button on the front panel.
If using the included IR remote control, press the
OK button.
ON
1 2
RMT-88A
6.
Press the ▲ or ▼ buttons on the front panel
or on the IR remote control to select the Reboot
Unit menu.
reboot unit
page | 66
Basic Operation
Menu System
7.
Press the Enter button on the front panel or the OK button on the IR remote
control. The matrix will prompt to confirm the factory-reset operation.
reboot unit
)yes
8.
Press and release the ▲ or ▼ buttons on the front panel or on the IR remote control,
to select either Yes or No.
reboot unit
)no
9.
Press the Enter button on the front panel or the OK button on the IR remote control
to confirm the selection.
If Yes is selected, then the matrix will automatically be rebooted.
page | 67
Basic Operation
The Web Interface
Introduction to the Web Interface
The Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder includes a built-in
web interface. We recommend that the web interface be used to control the matrix as it
provides easy management of all features used by the matrix.
►► Logging In
1.
Launch your favorite web browser.
2.
In the address bar, type the IP address of the matrix.
3.
The login page will be displayed.
4.
Select the user from the Username drop-down list.
•
Operator
The Operator username provides restricted access to the web interface.
This username allows access to both the Routing and Status tabs,
locking / unlocking and powering on / off the matrix.
The default password for the Operator user name is Operator.
All passwords are case-sensitive. For information on changing
the default password, see Configuring Network Settings (page 95).
page | 68
The Web Interface
Basic Operation
•
Administrator
The Administrator username provides full access to all features
within the web interface.
The default password for the Administrator user name is Admin.
All passwords are case-sensitive. For information on changing
the default password, see Configuring Network Settings (page 95).
5.
Enter the password for the selected username.
6.
Click the Login button.
7.
After a few moments, the Routing tab will be displayed.
►► Administrator vs Operator
As mentioned earlier, logging in as Operator provides restricted access to many
of the available features within the web interface. This is summarized in the table
below:
Administrator
Operator
•
•
Access to Routing and Status
tabs, only.
•
No access to the Preset Edit
button under the Routing tab.
Access to all features
page | 69
Basic Operation
The Web Interface
►► Tabs and Sub-tabs
The web interface is organized into tabs, in the top-portion of the screen. Clicking on
a tab will display a different screen.
The Setup and Manage EDID tab have their own set of tabs, which we will refer to as
“sub-tabs”, as shown below.
Screen tab
Screen sub-tab
►► Buttons
Several screen contain buttons which allow the selection of a particular mode or
setting. Click the button for the desired setting. Buttons that are red represent
a setting that is “turned on”. If the button is pale-yellow, then the feature is “turned off”:
•
Feature is “turned on”
•
Feature is “turned off”
page | 70
Basic Operation
The Web Interface
•
If a button is “grayed-out”, then this means that the setting is not available. This
usually requires that another setting must be enabled before setting a “sub-set”
of that feature.
For example, note that both the Login Message on Connect buttons are
disabled in the illustration, below:
In order to change these particular settings, TCP Access must be enabled.
After clicking the Enable button, next to TCP Access, the Login Message on
Connect buttons are now available.
►► Legend
The legend, near the bottom-right corner of the Routing screen, defines the colors
used to indicate the status of an input or output:
page | 71
Basic Operation
The Web Interface
Active / Good
Columns or rows that are highlighted in green, indicate that an active source or
sink is connected to the that input / output.
Error
Although a rare occurrence, this indicates an error (e.g. HDCP, etc.) with the
source or sink device. These rows or columns are highlighted in amber.
Inactive
Columns or rows which are highlighted in gray, indicate the absence of a source
or sink device on that input or output.
Preset / Available Route
Squares that are light tan, indicate that the input and output is available for
routing.
Switch Audio / Video
A red square indicates where an input has been routed to an output.
Off
Black squares indicate that the input is set to the OFF state. The OFF input is
an additional input that can be selected to simulate a source that is not present.
page | 72
Basic Operation
The Web Interface
Locking the Matrix
Locking the matrix disables the front-panel controls, IR routing, and the built-in web
interface. This is useful in preventing an accidental change to matrix settings by
inadvertently pressing any of the front-panel buttons.
Information
Locking the Matrix Controller will also disable routing and other operations
within the Web Interface.
1.
Click the Routing tab.
2.
Click the Lock button near the top of the screen.
3.
Once pressed, the Lock button will read “Unlock Matrix”. The Lock button on the front
panel will also glow bright blue. The matrix is now locked.
4.
Click the Unlock Matrix button to unlock the matrix.
5.
The Unlock button will now read “Lock”. The Lock button on the front panel will also
turn-off. The matrix is now unlocked.
page | 73
Basic Operation
The Web Interface
Viewing the Routing Status
1.
Click the Routing tab.
2.
Locate the desired output from the rows on the left, then read across until a routing
indicator (red square) is encountered.
Note the column where the red square is located. Each column identifies
an input and each row represents an output. The output and inputs names can be
changed, if desired. See Changing Input and Output Names (page 82) for more
information.
For example, in the illustration below, Input 2 is routed to Output C.
Input 2
Output C
page | 74
Basic Operation
The Web Interface
Routing Inputs and Masking Outputs
►► Routing Inputs
1.
Click the Routing tab.
2.
Located the desired output, from the rows on the left side of the screen.
3.
Click the desired input. Use the column, with the input names, as a guide when
selecting the input.
New routing state
4.
Click the square at the intersection of both the output and input.
A routing indicator (red square) will appear at the intersection of the row (output)
and column (input) of the current routing state.
If the routing process is successful, then a green bar will appear at the top of the
page with the text “Routed successfully”..
page | 75
Basic Operation
The Web Interface
►► Placing an input in the OFF state
1.
Click the box in the first column, next to the desired output.
2.
The box, in the column, will turn black, indicating that the input is “off”. The
OFF is an additional input that can be selected to simulate a source that is not
present.
“Off” state
As with any routing operation, if the operation is successful, a green bar will
appear at the top of the page with the text “Routed successfully”.
page | 76
Basic Operation
The Web Interface
►► Masking Outputs
1.
Click the Routing tab.
2.
Mask the desired output by clicking the Mask button. The Mask button will
turn red, indicating that the selected output is masked.
3.
To unmask the output, click the Mask button again. The button will turn gray.
page | 77
Basic Operation
The Web Interface
Routing Presets
►► Creating / Editing a Preset
1.
Click the Routing tab.
2.
Under the Presets section, click the Preset Edit button.
3.
The preset buttons will begin to flash and the Preset Edit button will read Choose
One.
page | 78
Basic Operation
The Web Interface
4.
Click the desired preset to edit.
5.
The selected preset will be highlighted. In this example, we will select Preset 6.
6.
Select the desired routing state for each input/output. See Routing Inputs and
Masking Outputs (page 75), if necessary. The preset selections for the selected
preset, will be indicated by a green square, as shown below. Note that an output can
also be set to OFF.
7.
To save/set the audio volume level for an output, click the check box, next to the
volume slider, then set the volume slider to the desired level.
page | 79
Basic Operation
The Web Interface
8.
After the desired routing states, for input/output have been assigned, provide a name
for the preset in the Preset Name field.
►► To clear the preset selections for the current preset, click the Clear All button.
►► To use the current routing state as the preset selection, click the Select Current
button.
►► To abort the editing of the preset, click the Cancel button.
9.
Click the Save to Preset button to save the preset.
10. Repeat steps 2 - 8, as desired, for each preset.
►► Recalling a Preset
1.
Click the Routing tab.
2.
Click the desired preset button.
page | 80
Basic Operation
The Web Interface
Input and Output Status
Provides video and audio information for all inputs and outputs.
1.
Click the Status tab within the built-in web interface.
2.
Information on each input is listed in the top portion of the screen.
3.
Information on each output is listed in the bottom portion of the screen.
Input section
Output section
The table below outlines the information that is available for each section:
Input
•
•
•
•
•
•
•
•
•
•
•
•
Output
Color depth
Color space
HDR
HDCP (version)
3D (status)
Active Signal
Vertical resolution
Horizontal Resolution
Progressive / interlaced
Refresh rate
Video mode
Audio Format
•
•
•
•
page | 81
Rsense
HDP
HDCP
Video mode
Basic Operation
The Web Interface
Changing Input and Output Names
By default, the names of each output are Output A - Output D. The names of each input
are Input 1 - Input 4. Each of these names can be changed, as desired, to suit the type of
device that is connected to the input or output.
Information
Both input and output names cannot exceed 12 characters in length.
1.
Click the Setup tab within the built-in web interface.
2.
Click the Names sub-tab.
3.
Click in the field of the desired output or input to be changed.
4.
Once all changes have been made, click the Save button.
5.
The new input / output name(s) will be displayed within the Routing tab. Note that
the new input / output name(s), to the left of each field, will not be changed.
page | 82
Basic Operation
The Web Interface
Audio
The Audio tab handles how audio is output from the matrix.
1.
Click the Setup tab within the built-in web interface.
2.
Click the Audio sub-tab.
3.
Click either Fixed or Variable for each output.
•
Fixed
In this mode, the output volume is set to 100 and variable adjustment is disabled.
•
Variable
In this mode, volume is adjustable between 0 and 100.
page | 83
Basic Operation
The Web Interface
HPD Control
HPD (Hot-Plug Detect) is an HDMI feature which senses if the HDMI cable is disconnected,
from the source or sink device, and then re-initializes the HDMI link if necessary.
Within the web interface, the HPD pulse can be sent to the selected input, and reset the
HDMI connection without disconnecting any cables. The connected display will flash when
an HPD signal is received.
1.
Click the Setup tab within the built-in web interface.
2.
Click the HPD Control sub-tab.
3.
Click the Pulse button for the desired input. Click the Pulse All Inputs button to send
an HPD signal to all inputs.
page | 84
Basic Operation
The Web Interface
HDCP
This feature allows HDCP content to either be passed-through or rejected on each input.
Outputs can either follow the input status or can be set to always encode HDCP. Note that
using the “Reject” feature, on an input, does not decrypt HDCP content.
1.
Click the Setup tab within the built-in web interface.
2.
Click the HDCP sub-tab.
3.
For inputs, select the desired button next to the input.
►► Reject - Does not allow HDCP content to be passed through. Click the
Reject All button to set all inputs to Reject.
►► 2.2 - Click this button if the sink device supports HDCP 2.2. Click the
All 2.2 button to set all inputs to 2.2.
►► 1.4 - Click this button if the sink device only supports HDCP 1.4. Click the
All 1.4 button to set all inputs to 1.4.
page | 85
Basic Operation
The Web Interface
4.
For outputs, select the desired button next to the output.
►► Follow Input - Click this button to have the output follow the setting used on the
input. Click the Follow All button to set all outputs to Follow Input.
►► Always Encode - Encodes the output signal with HDCP 2.2, regardless of the
input signal.
Click the All Encode button to set all outputs to Always Encode.
page | 86
Basic Operation
The Web Interface
Setting the EDID Mode
The EDID Mode tab allows the desired EDID mode (internal preset, external, or custom)
to be set for each input.
1.
Click the Manage EDID tab within the built-in web interface.
2.
Click the EDID Mode sub-tab.
3.
Select the desired EDID mode for each input using the drop-down list.
If the EDID Mode is set to External, then the name of the downstream EDID (device)
will appear under the EDID Name column, as shown. The External modifies the
EDID, parsing all outputs to determine optimum compatibility among features for all
connected displays.
page | 87
Basic Operation
The Web Interface
►► Using a Custom EDID
The Custom - User-defined setting is used to store a custom EDID in the
selected input. To use a custom EDID, follow the instructions below:
1.
Select Custom - User-defined from the drop-down list of the desired input.
2.
Copy or upload an EDID to the input that is using the Custom mode.
See one of the following sections for more information on copying or
uploading EDID data:
►► Copying EDID Data (page 89).
►► Uploading and Downloading EDID Data (page 92).
3.
Set the EDID Lock mode to either Locked or Unlocked:
►► Locked
Prevents the EDID from being changed on the input..
►► Unlocked
Allows the EDID to be changed.
4.
The name of the custom EDID will appear under the EDID Name column.
page | 88
Basic Operation
The Web Interface
Copying EDID Data
The EDID Copy tab allows an EDID to be copied from an input or output (sink device) to
any input. In order to copy an EDID to an input, the input must be set to Custom - Userdefined mode and then unlocked. See Setting the EDID Mode (page 87) for more
information.
1.
Click the Manage EDID tab within the built-in web interface.
2.
Click the EDID Copy sub-tab.
3.
Click the button of the desired output or input from the Select EDID to Copy section.
Select only one input or output at a time.
page | 89
Basic Operation
The Web Interface
4.
After the input or output is selected, click the button for the corresponding input where
the EDID will be copied. One or more inputs can be selected at a time.
5.
Click the Copy button. The Copy can only be pressed when both an output or input
(the source) and an input (destination) are selected.
6.
The EDID copy process is complete. Repeat steps 3 - 5 as desired.
Information
If an Input destination is disabled (“grayed-out”), then this means that the
EDID has not been set to “User-Defined”. See Setting the EDID Mode (page
40) for information on setting the EDID mode.
page | 90
Basic Operation
The Web Interface
Getting EDID Information
The EDID Info tab allows the EDID information, from an input or sink device, to be
displayed.
1.
Click the Manage EDID tab within the built-in web interface.
2.
Click the EDID Info sub-tab.
3.
Select the desired input or output from the Choose EDID drop-down list.
4.
The EDID information for the selected input or output will be displayed.
page | 91
Basic Operation
The Web Interface
Uploading and Downloading EDID Data
The Upload / Download tab allows EDID data from an input, output, or one of the internal
EDID presets, to be downloaded and saved as a file on your computer. An EDID file can
also be uploaded to any (unlocked) input.
►► Downloading an EDID
1.
Click the Manage EDID tab within the built-in web interface.
2.
Click the Upload/Download sub-tab.
3.
Select the desired input, output, or internal EDID preset to be downloaded
using the Select EDID File drop-down list.
4.
Click the Download button.
page | 92
Basic Operation
The Web Interface
5.
The following dialog will be displayed:
6.
Click the Save File button to save the EDID file to your computer.
•
Mac OS X
The file will automatically be saved under
Macintosh HD\Users\[username]\Downloads.
•
Windows OS
The file will be saved under
C:\Users\[username]\Downloads.
page | 93
Basic Operation
The Web Interface
►► Uploading an EDID
1.
Click the Manage EDID tab within the built-in web interface.
2.
Click the Upload/Download tab.
3.
Set the input, where the EDID file will be uploaded, to Custom mode.
See Setting the EDID Mode (page 87) for more information.
4.
Click the Browse... button under Upload EDID section.
5.
The File Upload dialog will be displayed.
6.
Select the EDID file from your computer. The EDID file must be in .bin format.
After the file is selected, click the OK button on the dialog box.
7.
Select the input where the EDID will be uploaded using the Select
Destination drop-down list. In order for an input to be selected, it must be
unlocked and set to Custom. Refer to Setting the EDID Mode (page 87) for
more information.
8.
Click the Upload button.
page | 94
Basic Operation
The Web Interface
Configuring Network Settings
Once the matrix is configured on the network using Gefen Syner-G, the network settings
can be changed within the built-in web interface. To access the network settings, click the
Network tab in the built-in web interface.
When changing any network setting, click the Save button at the bottom of the page.
To revert network settings to factory default, click the Set Network Defaults button.
►► IP Settings
1.
Set the network mode by clicking the Static or DHCP button.
2.
If set to Static mode, then enter the IP address, subnet mask, and
gateway address in the IP Address, Subnet, and Gateway fields,
respectively. If set to DHCP mode, the DHCP server will assign these values.
3.
Enter the HTTP listening port in the HTTP Port field.
page | 95
Basic Operation
The Web Interface
►► TCP / Telnet Settings
For details on configuring TCP, see Using Telnet, UDP, and RS-232 (page 112).
•
TCP Access: Click the Enable button to allow Telnet access to the matrix.
Otherwise, click the Disable button.
•
TCP Port: Enter the TCP listening port in this field.
•
Login Message on Connect: Click the Show button to display the
welcome message at the beginning of a Telnet session. Otherwise, click
the Hide button.
•
Require Password on Connect: Click the Enable button to require
password credentials at the beginning of a Telnet session.
page | 96
Basic Operation
The Web Interface
•
User Name: This field is static and cannot be changed. Telnet sessions
are restricted to Admin users.
•
Old Password: Enter the old (current) password in this field.
The factory-default password is admin.
•
New Password: Enter the new password in this field.
•
Confirm New Password: Confirm the new password by entering the new
password in this field.
Information
Note that all passwords are case-sensitive.
page | 97
Basic Operation
The Web Interface
►► UDP Settings
For details on configuring UDP, see Using Telnet, UDP, and RS-232 (page 112).
•
UDP Access: Click the Enable button to use the UDP protocol with the matrix.
Otherwise, click the Disable button.
•
UDP Port: Enter the TCP listening port in this field.
•
Remote UDP Access: Click the Enable button to set the remote UDP address
and UDP listening port. This feature only needs to be enabled if feedback to the
matrix is required. Otherwise, this feature can be disabled.
•
Remote UDP IP Address: Enter the remote UDP IP address in this field.
•
Remote UDP Port: Enter the remote UDP listening port in this field.
page | 98
Basic Operation
The Web Interface
►► Web Login Settings
•
Username: To change the password for the Administrator, click the
Administrator. Otherwise, click the Operator button.
•
New Password: Enter password for the selected username (above),
in this field. Passwords are case-sensitive.
•
Old Password: Enter the old (current) password in this field. Passwords are
case-sensitive.
•
Confirm New Password: To confirm the new password, re-enter the new
password in this field. Passwords are case-sensitive.
The default password for the Administrator username is admin.
The default password for the Operator username is operator.
page | 99
Basic Operation
The Web Interface
►► Discovery Protocol Settings
•
Enable Discovery: Click the Enable button to enable “discovery” mode.
Otherwise, click the Disabled button. In order for Gefen Syner-G to
discover the matrix on a network, this feature must be enabled.
•
Find Your Device: Click the Show Me button to physically locate the matrix
on a network. In order for the Show Me button to be available, the Enable
Discovery button must be set to Enable. When the Show Me button is clicked,
the button text will change to Hide Me and the buttons, on the front panel,
will flash on the front panel of the matrix:
®
Menu
Preset
out a :output a
A/V In:input 01
Enter
IR
Discovery Read Only: When set to Read Only, the IP settings for the
matrix will be displayed by Syner-G but they cannot be changed. In order
to display and change IP settings from within Gefen Syner-G, click the
Read / Write button.
EXT-UHD600A-88
L/R
IP Control
•
Power
4K 60 Hz 4:4:4, HDMI 2.0, HDCP 2.2
Ultra HD 600 MHz 8x8 Matrix w/HDR and Audio De-Embedder
•
Reset
Lock
Back
IR In/Ext
L/R
Out A
L/R
Out B
L/R
Out C
L/R
Out D
L/R
Out E
L/R
Out F
L/R
Out G
Out H
Product Description: EXT-UHD600A-88 is the default product description.
This name will be used to identify the matrix when using the Gefen Syner-G
software.
RS-232
In 1
In 2
In 3
In 4
page | 100
In 5
In 6
In 7
In 8
24V DC
Basic Operation
The Web Interface
System Settings
The System tab provides controls for various other matrix features. Each of these controls
is described below.
►► Main RS-232 Feedback
•
Click the Off button to disable RS-232 feedback.
•
Click the On button to enable RS-232 feedback.
►► LED Brightness
Increases / decreases the brightness of the front-panel display.
•
Move the slider to the right to increase the brightness.
•
Move the slider to the left to decrease the brightness.
page | 101
Basic Operation
The Web Interface
►► Download Current Configuration to PC
Saves the current matrix configuration to a file on your computer.
1.
Click the Download button.
2.
The following dialog box will be displayed:
page | 102
Basic Operation
The Web Interface
3.
Click the Save File button to save the configuration file to your computer.
•
Mac OS X
The file will automatically be saved under
Macintosh HD\Users\[username]\Downloads
•
Windows OS
The file will be saved under
C:\Users\[username]\Downloads
►► Restore / Upload Configuration File
Uploads the selected matrix configuration, from a file on your computer, to the matrix.
1.
Click the Browse... button.
2.
Select the desired configuration file from your computer. After the file has been
selected, the filename will appear next to the Browse... button.
3.
Click the Restore button to upload the file.
page | 103
Basic Operation
The Web Interface
►► Firmware Update
Uploads and applies the latest firmware file to the matrix.
1.
Download the latest firmware from the Gefen web site.
2.
Click the Browse... button.
3.
Select the firmware file on your computer.
The firmware must be a .bin file and will have the following naming
convention: EXT-UHD600A-88([version])(PACK).bin.
4.
Click the Update button.
5.
The following message box will be displayed:
WARNING: Updating the firmware may overwrite some
of your settings. Consider saving the configuration
before updating the firmware. Are you sure you want
to continue?
To save the configuration, before continuing, click the Cancel button on the
message box. Refer to the section Download Current Configuration to PC.
6.
Click the OK button on the message box.
page | 104
Basic Operation
The Web Interface
7.
After a few moments, the following message box will be displayed within the web
interface:
8.
After the update process completes, the matrix will automatically reboot.
page | 105
Basic Operation
The Web Interface
►► Setting the IR Channel
Sets the IR channel for the matrix. The matrix must be set to the same IR
channel as the included IR remote control, in order for the IR remote control to
communicate with the matrix.
1.
Click the desired IR channel for the matrix by clicking one of the
IR Channel buttons (1 - 4).
The IR channel setting is automatically saved. Rebooting the matrix
is not required.
page | 106
Basic Operation
The Web Interface
►► Performing a Factory Reset
This feature restores the matrix to original factory-default settings.
Important
Performing this function will erase all current setting in your matrix. IP settings
will be retained. To save the configuration, before continuing, refer to the
section Download Current Configuration to PC.
1.
Click the Reset button.
2.
The following message box will be displayed:
►► Click the OK button to continue with the reset procedure.
►► Click the Cancel button to abort the reset procedure and return
to the web interface.
page | 107
Basic Operation
The Web Interface
►► Rebooting the matrix
Clicking this button will reboot the matrix.
1.
Click the Reboot button.
2.
The following message box will be displayed:
►► Click the OK button to continue with the reboot procedure.
►► Click the Cancel button to abort the reboot procedure and return
to the web interface.
page | 108
This page left intentionally blank.
This page left intentionally blank.
600 MHz
4K ULTRA
8x8 Matrix
w/HDR and Audio De-Embedder
3
Advanced Operation
Advanced Operation
Using Telnet, UDP, and RS-232
Telnet Configuration
1.
Launch the desired terminal application. For example, on the Windows operation
system, we can use Hyperterminal; on Mac OS X, we can use the Terminal
application.
2.
At the command prompt, type the following:
telnet ip_address
where ip_address is the IP address of the matrix.
3.
After correct settings have been used in the terminal program, information similar to
the following will be displayed:
Welcome to EXT-UHD600A-88 Telnet
telnet->
4.
Type #help for a list of commands or refer to the tables on the following pages.
UDP Configuration
1.
Configure the desired control system for UDP.
2.
Click the Network tab, within the web interface, and do the following.
See Configuring Network Settings (page 95) for more information.
a.
Click the Enabled button next to UDP Access.
b.
Enter the UDP listening port in the UDP Port field. The default UDP listening port
is 50007.
c.
Click the Enabled button next to Remote UDP Access. This feature only needs
to be enabled if feedback to the matrix is required. Otherwise, this feature can
be disabled.
d.
If enabling Remote UDP Access, enter the remote UDP IP address in the
Remote UDP IP Address field. This IP address should be the same as the
control system. The default IP address is 192.168.1.255.
e.
If enabling Remote UDP Access, enter the remote UDP listening port in the
Remote UDP Port field. The default remote UDP listening port is 50008.
f.
Click the Save button at the bottom of the Network screen.
page | 112
Advanced Operation
Using Telnet, UDP, and RS-232
RS-232 Configuration
1.
Selected the desired COM port.
2.
Configure the RS-232 port to the following settings. Note that Only TxD, RxD,
and GND pins are used.
Description
Setting
Baud rate
19200
Data bits
8
Parity
None
Stop bits
1
Hardware flow control
None
3.
Connect to the RS-232 port.
4.
Type #help for a list of commands or refer to the tables on the following pages.
page | 113
Advanced Operation
Commands
Discovery Service
Command
Description
#get_device_desc
Returns the current device-description string
#get_discovery
Returns the current state of the discovery service
#get_discovery_mode
Returns the “discovery” mode
#get_showme
Returns the “show me” state
#set_device_desc
Sets the description of the matrix
#set_discovery
Enables or disables the discovery service
#set_discovery_mode
Sets the “discovery” mode
#set_showme
Enables or disables the “show me” feature
Input Status
Command
Description
#gets_input_hdcp
Returns the HDCP setting of the specified input
#gets_input_hpd
Returns the HPD state of the specified input
#gets_input_mode
Returns the video mode of the specifed input
#gets_input_signal
Returns the active signal state of the specified input
Manage EDID
Command
Description
#get_custom_edid
Download the custom EDID from the specified input
#get_edid_lock
Returns the EDID-lock status of the specified input
#get_edid_mode
Returns the EDID mode of the specified input
#get_external_edid
Download the modified external EDID
#get_input_edid
Download the current EDID from an input
#get_internal_edid
Downloads a preset internal EDID
#get_output_edid
Downloads a downstream EDID from an input
#send_custom_edid
Uploads a custom EDID to an input
#set_edid_copy
Enables or disables EDID copy
#set_edid_lock
Sets the EDID lock setting on the specified input
#set_edid_mode
Sets the EDID mode on the specified input
page | 114
Advanced Operation
Commands
Network Settings
Command
Description
#get_gateway
Returns the gateway IP address of the matrix
#get_ip_address
Returns the IP address of the matrix
#get_ip_mode
Returns the IP mode of the matrix
#get_ipconfig
Returns the matrix IP configuration
#get_mac_addr
Returns the MAC address of the matrix
#get_netmask
Returns the subnet mask of the matrix
#get_remote_udp_access
Returns the remote UDP access state of the matrix
#get_remote_udp_ip
Returns the remote UDP IP address of the matrix
#get_remote_udp_port
Returns the remote UDP listening port
#get_telnet_access
Returns the Telnet access state
#get_telnet_login
Returns the current status of the Telnet login process
#get_telnet_message
Returns the Telnet login welcome message status
#get_telnet_port
Returns the Telnet listening port
#get_udp_access
Returns the UDP access state
#get_udp_port
Returns the UDP listening port
#get_web_port
Returns the HTTP listening port
#set_gateway
Sets the gateway address
#set_ip_address
Sets the IP address
#set_ip_mode
Sets the IP mode
#set_netmask
Sets the subnet mask for the matrix
#set_remote_udp_access
Enables or disables remote UDP access
#set_remote_udp_ip
Sets the remote UDP IP address
#set_remote_udp_port
Sets the remote UDP listening port on the matrix
#set_telnet_access
Enables or disables Telnet access
#set_telnet_login
Enables or disables the Telnet login process
#set_telnet_message
Enables or disable the Telnet welcome message
#set_telnet_port
Sets the Telnet listening port on the matrix
#set_udp_access
Enables or disables UDP access
#set_udp_port
Sets the UDP listening port on the matrix
#set_web_port
Sets the HTTP listening port
page | 115
Advanced Operation
Commands
Output Status
Command
Description
#gets_output_hdcp
Returns the HDCP state of the specified output
#gets_output_hpd
Returns the HPD state of the specified output
#gets_output_mode
Returns the video mode of the specified output
#gets_output_rsense
Returns the output Rsense
Presets
Command
Description
#get_preset_name
Returns the name of the specified preset
#set_preset_name
Sets the name of the specified preset
p
Recalls the specified preset
Routing
Command
Description
#get_mask
Returns the mask status for the specified output(s)
#lock_matrix
Locks or unlocks the matrix
#set_mask
Sets masking on the specified output(s)
r
Routes an input to an output
s
Returns the current routing state for all inputs/outputs
page | 116
Advanced Operation
Commands
Setup
Command
Description
#get_audio_output
Returns the audio mode for the specified output(s)
#get_input_hdcp
Returns the HDCP handshake more on an input
#get_io_name
Returns the name of the specified input
#get_output_hdcp
Returns the HDCP setting of the specified output
#send_hpd
Sends an HPD signal to the specified input
#set_audio_output
Sets analog audio mode for the specified output(s)
#set_input_hdcp
Sets the HDCP setting on the specified input
#set_io_name
Sets the name of the specified input or output
#set_output_hdcp
Sets the HDCP setting on the specified output
System Settings
Command
Description
#factory_reset
Resets the matrix to factory-default settings
#get_feedback
Returns the feedback state
#get_firmware_version
Returns the current version of matrix firmare
#get_ir_channel
Returns the current IR channel on the matrix
#get_lcd_brightness
Returns the current LED brightness setting
#help
Returns a list of available commands
#reboot
Reboots the matrix
#set_feedback
Enables or disables unsolicited RS-232 feedback
#set_ir_channel
Sets the IR channel of the matrix
#set_lcd_brightness
Sets the brightness of the LCD display
Volume
Command
Description
#get_mute
Returns the muting status for the specified output(s)
#get_vol
Returns the analog output volume for the output(s)
#set_mute
Sets the audio muting for the specified output(s)
#set_vol
Sets the analog output volume for the output(s)
page | 117
Advanced Operation
Commands
#factory_reset
Resets the matrix to factory-default settings. If a factory reset is performed through the
built-in web interface or Telnet, then IP settings will be preserved. To reset all, including IP
settings, this command must be issued using RS-232.
Syntax
#factory_reset
Parameters
None
Example
#factory_reset
RESET TO FACTORY DEFAULTS
EXT-UHD600A-88 V1.00
OUT:ABCDEFGH
IN:12345678
Related Commands
#reboot
page | 118
Advanced Operation
Commands
#get_audio_output
Returns the analog audio mode for the specified output(s). The value returned is one of the
following:
Type
Description
F
Fixed
V
Variable
Syntax
#get_audio_output out
Parameters
Parameters
out
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#get_audio_output a
AUDIO_OUTPUT A V
Related Commands
#set_audio_output
page | 119
Advanced Operation
Commands
#get_custom_edid
Downloads the customer EDID from the specified input.
Syntax
#get_custom_edid input
Parameters
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8).
Example
#get_custom_edid 1
00FFFFFFFFFFFF001CA6000000000000...
Related Commands
#get_edid_lock
#get_edid_mode
#get_external_edid
#get_input_edid
#get_internal_edid
#get_output_edid
#send_custom_edid
#set_edid_copy
#set_edid_lock
#set_edid_mode
page | 120
Advanced Operation
Commands
#get_device_desc
Returns the description of the matrix.
Syntax
#get_device_desc
Parameters
None
Example
#get_device_desc
DEVICE DESCRIPTION IS EXT-UHD600A-88
Related Commands
#set_device_desc
page | 121
Advanced Operation
Commands
#get_discovery
Returns the discovery mode setting. The value returned is one of the following:
Value
Description
0
“Discovery” mode is disabled
1
“Discovery” mode is enabled
Syntax
#get_discovery
Parameters
None
Example
#get_discovery
DISCOVERY 1
Related Commands
#set_discovery
#set_showme
page | 122
Advanced Operation
Commands
#get_discovery_mode
Returns the current “discovery” mode. The value returned is one of the following:
Value
Description
0
Read only
1
Read / Write
Syntax
#get_discovery_mode
Parameters
None
Example
#get_discovery_mode
#get_discovery_mode 1
Related Commands
#get_discovery
#set_discovery
#set_discovery_mode
page | 123
Advanced Operation
Commands
#get_edid_lock
Returns the current “EDID Lock” state of the specified input. The value returned
is one of the following:
Value
Description
0
EDID unlocked
1
EDID locked
Syntax
#get_edid_lock input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query.
Example
#get_edid_lock 1
EDID_LOCK 1 0
Related Commands
#get_edid_mode
#set_edid_copy
#set_edid_lock
#set_edid_mode
page | 124
Advanced Operation
Commands
#get_edid_mode
Returns the EDID mode of the specified input. The value returned is one of the following:
Value
Description
1
UHD 4K 600 MHz 2Ch
2
UHD 4K 600 MHz Multi
3
UHD 4K 300 MHz 2Ch
4
UHD 4K 600 MHz Multi
5
1080P 2Ch
6
1080 Multi
7
External
8
Custom - User
Syntax
#get_edid_mode input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query.
Example
#get_edid_mode 1
#get_edid_mode 1 2
Related Commands
#get_edid_lock
#set_edid_copy
#set_edid_lock
#set_edid_mode
page | 125
Advanced Operation
Commands
#get_external_edid
Returns the modified external EDID.
Syntax
#get_external_edid
Parameters
None
Example
#get_external_edid
00FFFFFFFFFFFF001CA6000000000000...
Related Commands
#get_custom_edid
#get_edid_lock
#get_edid_mode
#get_input_edid
#get_internal_edid
#get_output_edid
#send_custom_edid
#set_edid_copy
#set_edid_lock
#set_edid_mode
page | 126
Advanced Operation
Commands
#get_feedback
Returns the feedback status.
Syntax
#get_feedback
Parameters
None
Example
#get_feedback
FEEDBACK 1
Related Commands
#factory_reset
#get_firmware_version
#get_ir_channel
#get_lcd_brightness
#help
#reboot
#set_feedback
#set_ir_channel
#set_lcd_brightness
page | 127
Advanced Operation
Commands
#get_firmware_version
Returns the current firmware version of the matrix.
Syntax
#get_firmware_version
Parameters
None
Example
#get_firmware_version
FIRMWARE VERSION IS 1.0
Related Commands
#factory_reset
#get_feedback
#get_ir_channel
#get_lcd_brightness
#help
#reboot
#set_feedback
#set_ir_channel
#set_lcd_brightness
page | 128
Advanced Operation
Commands
#get_gateway
Returns the gateway address of the matrix.
Syntax
#get_gateway
Parameters
None
Example
#get_gateway
GATEWAY 10.5.64.1
Related Commands
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 129
Advanced Operation
Commands
#get_input_edid
Returns the current EDID from the specified input.
Syntax
#get_input_edid input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query.
Example
#get_input_edid
00FFFFFFFFFFFF001CA6000000000000...
Related Commands
#get_custom_edid
#get_external_edid
#get_edid_lock
#get_edid_mode
#get_internal_edid
#get_output_edid
#send_custom_edid
#set_edid_copy
#set_edid_lock
#set_edid_mode
page | 130
Advanced Operation
Commands
#get_input_hdcp
Returns the HDCP handshake mode of the specified input.
Syntax
#get_input_hdcp
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query. Set this parameter to 0 to return
the HDCP handshake mode of all inputs in numerical order.
Example
#get_input_hdcp 1
INPUT_HDCP 1 2
Related Commands
#set_input_hdcp
page | 131
Advanced Operation
Commands
#get_internal_edid
Returns the specified preset internal EDID.
Syntax
#get_internal_edid edidps
Parameters
edidps
Type: INTEGER
The number of the EDID preset.
EDID
Description
1
UHD 600 4K 2CH
2
UHD 600 4K MULTICH
3
UHD 300 4K 2CH
4
UHD 300 4K MULTICH
5
1080P 2CH
6
1080P MULTICH
Example
#get_internal_edid 1
00FFFFFFFFFFFF001CA6000000000000...
page | 132
Advanced Operation
Commands
#get_io_name
Returns the name given to the specified input or output.
Syntax
#get_io_name inout
Parameters
input
Type: INTEGER or CHARACTER
The number of the HDMI input (1 - 8) to query.
Example
#get_io_name 1
IO_NAME 1 Bluray
Related Commands
#set_io_name
page | 133
Advanced Operation
Commands
#get_ip_address
Returns the current IP address of the matrix.
Syntax
#get_ip_address
Parameters
None
Example
#get_ip_address
IP_ADDRESS 10.5.64.81
Related Commands
#get_gateway
#get_web_port
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 134
Advanced Operation
Commands
#get_ip_mode
Returns the current IP mode of the matrix. The value returned is one of the following:
Value
Description
0
Static mode
1
DHCP mode
Syntax
#get_ip_mode
Parameters
None
Example
#get_ip_mode
IP_MODE 0
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 135
Advanced Operation
Commands
#get_ipconfig
Returns the current IP configuration of the matrix. In addition to providing the MAC
address and the broadcast IP address, this command also provides the same
information as executing the #get_ip_address, #get_netmask, #get_gateway,
and #get_mac_addr ommands.
Syntax
#get_ipconfig
Parameters
None
Example
#get_ipconfig
IP CONFIGURATION IS :
IP: 10.5.64.81
NETMASK: 255.255.255.0
GATEWAY: 10.5.64.1
MAC ADDRESS: 00:1C:91:04:90:03
Related Commands
#get_gateway
#get_web_port
#get_ip_mode
#get_ip_address
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 136
Advanced Operation
Commands
#get_ir_channel
Returns the IR channel of the matrix.
Syntax
#get_ir_channel
Parameters
None
Example
#get_ir_channel
IR_CHANNEL 1
Related Commands
#set_ir_channel
page | 137
Advanced Operation
Commands
#get_lcd_brightness
Returns the brightness level of the LED indicators on the front panel.
Syntax
#get_lcd_brightness
Parameters
None
Example
#get_lcd_brightness
LCD_BRIGHTNESS 60
Related Commands
#set_lcd_brightness
page | 138
Advanced Operation
Commands
#get_mac_addr
Returns the MAC address of the matrix.
Syntax
#get_mac_addr
Parameters
None
Example
#get_mac_addr
MAC ADDRESS IS: 00:1C:91:04:90:03
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 139
Advanced Operation
Commands
#get_mask
Returns the mask state for the specified output(s).
Syntax
#get_mask output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#get_mask a
MASK A 0
Related Commands
page | 140
Advanced Operation
Commands
#get_mute
Returns the audio muting status for the specified output(s).
Syntax
#get_mute output
Parameters
output
Type: INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#get_mute A
#get_mute 0
Related Commands
page | 141
Advanced Operation
Commands
#get_netmask
Returns the current subnet mask of the matrix.
Syntax
#get_netmask
Parameters
None
Example
#get_netmask
NETMASK 255.255.255.0
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 142
Advanced Operation
Commands
#get_output_edid
Returns the downstream EDID from the specified output.
Syntax
#get_output_edid output
Parameters
output
Type: CHAR
The alphabetic identifier of the output (A - H).
Example
#get_output_edid a
00FFFFFFFFFFFF001CA6000000000000...
Related Commands
page | 143
Advanced Operation
Commands
#get_output_hdcp
Returns the HDCP setting of the specified output. The value returned is one of the
following:
Value
Description
0
Follow input
1
Always encode
Syntax
#get_output_hdcp output
Parameters
output
Type: CHARACTER
The identifier of the HDMI output (A - H) to query. Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#get_output_hdcp c
OUTPUT_HDCP C 1
Related Commands
#set_output_hdcp
page | 144
Advanced Operation
Commands
#get_preset_name
Returns the name of the specified preset.
Syntax
#get_preset_name preset
Parameters
preset
Type: INTEGER
The identifier of the preset name (1 - 16) to query.
Example
#get_preset_name 5
PRESET_NAME 5 Kitchen
Related Commands
#set_preset_name
page | 145
Advanced Operation
Commands
#get_remote_udp_access
Returns the remote UDP access state. The value returned is one of the following:
Value
Description
0
Remote UDP access disabled
1
Remote UDP access enabled
Syntax
#get_remote_udp_access
Parameters
None
Example
#get_remote_udp_access
REMOTE_UDP_ACCESS 0
Related Commands
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 146
Advanced Operation
Commands
#get_remote_udp_ip
Returns the remote UDP IP address.
Syntax
#get_remote_udp_ip
Parameters
None
Example
#get_remote_udp_access
REMOTE_UDP_IP 192.168.1.255
Related Commands
#get_remote_udp_access
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 147
Advanced Operation
Commands
#get_remote_udp_port
Returns the remote UDP listening port.
Syntax
#get_remote_udp_port
Parameters
None
Example
#get_remote_udp_port
REMOTE_UDP_PORT 50008
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 148
Advanced Operation
Commands
#get_showme
Returns the “showme” state.
Value
Description
0
Show me disabled
1
Shoe me enabled
Syntax
#get_showme
Parameters
None
Example
#get_showme
SHOW_ME 0
Related Commands
page | 149
Advanced Operation
Commands
#get_telnet_access
Returns the Telnet access state. Use the #set_telnet_access command to enable
or disable Telnet access.
Syntax
#get_telnet_access
Parameters
None
Example
#get_telnet_access
TELNET_ACCESS 1
Related Commands
#get_telnet_port
#get_telnet_message
#set_telnet_access
#set_telnet_port
#set_telnet_message
page | 150
Advanced Operation
Commands
#get_telnet_login
Returns the status of the Telnet login process.
Syntax
#get_telnet_login
Parameters
None
Example
#get_telnet_login
TELNET_LOGIN 0
Related Commands
page | 151
Advanced Operation
Commands
#get_telnet_message
Returns the Telnet welcome message. Use the #set_telnet_message to create
a custom welcome message.
Syntax
#get_telnet_message
Parameters
None
Example
#get_telnet_message
TELNET WELCOME SCREEN IS ENABLED
Related Commands
#get_telnet_access
#get_telnet_port
#set_telnet_access
#set_telnet_port
#set_telnet_message
page | 152
Advanced Operation
Commands
#get_telnet_port
Returns the Telnet listening port.
Syntax
#get_telnet_port
Parameters
None
Example
#get_telnet_port
TELNET_PORT 23
Related Commands
#get_telnet_access
#get_telnet_message
#set_telnet_access
#set_telnet_port
#set_telnet_message
page | 153
Advanced Operation
Commands
#get_udp_access
Returns the UDP access state. Use the #set_udp_access command to enable
or disable UDP access. The value returned is one of the following:
Value
Description
0
UDP access disabled
1
UDP access enabled
Syntax
#get_udp_access
Parameters
None
Example
#get_udp_access
UDP_ACCESS 0
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 154
Advanced Operation
Commands
#get_udp_port
Returns the local UDP listening port.
Syntax
#get_udp_port
Parameters
None
Example
#get_udp_port
UDP_PORT 50007
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 155
Advanced Operation
Commands
#get_vol
Returns the analog output volume level for the specified output(s).
Syntax
#get_vol output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#get_vol a
VOL A 100
Related Commands
page | 156
Advanced Operation
Commands
#get_web_port
Returns the HTTP listening port of the matrix.
Syntax
#get_web_port
Parameters
None
Example
#get_web_port
HTTP_PORT 80
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 157
Advanced Operation
Commands
#gets_input_hdcp
Returns the HDCP mode of the specified input. The value returned is one of the following:
Value
Description
0
Reject
1
HDCP 2.2 and below
2
HDCP 1.4 and below
Syntax
#gets_input_hdcp input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query. Specify 0 to query all inputs;
results are returned in input order 1 - 8.
Example
#gets_input_hdcp 1
INPUT_HDCP 1 0
Related Commands
#get_output_hdcp
#set_input_hdcp
#set_output_hdcp
page | 158
Advanced Operation
Commands
#gets_input_hpd
Returns the HPD state of the specified input. The value returned is one of the following:
Value
Description
L
HPD low
H
HPD high
Syntax
#gets_input_hpd input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query. Specify 0 to query all inputs;
results are returned in numerical order.
Example
#gets_input_hpd 1
INPUT_HDCP 1 0
Related Commands
page | 159
Advanced Operation
Commands
#gets_input_mode
Returns the video mode of the specified input.
Syntax
#gets_input_mode input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query. Specify 0 to query all inputs;
results are returned in input order 1 - 8.
Example
#gets_input_mode 1
INPUT_MODE 1 C
Related Commands
page | 160
Advanced Operation
Commands
#gets_input_signal
Returns the active signal status of the specified input.
Syntax
#gets_input_signal input
Parameters
input
Type: INTEGER
The number of the HDMI input (1 - 8) to query. Specify 0 to query all inputs;
results are returned in input order 1 - 8.
Example
#gets_input_signal 1
INPUT_SIGNAL 1 Y
page | 161
Advanced Operation
Commands
#gets_output_hdcp
Returns the HDCP status of the specified output. The value returned will be one of the
following:
Value
Description
1
Encrypted (HDCP 1.4)
2
Encrypted (HDCP 2.2)
U
Unencrypted
F
Fail
Syntax
#gets_output_hdcp output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#gets_output_hdcp a
OUTPUT_HDCP A 2
page | 162
Advanced Operation
Commands
#gets_output_hpd
Returns the HPD status of the specified output. The value returned will be one of the
following:
Value
Description
L
HPD low
H
HPD high
Syntax
#gets_output_hpd output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#gets_output_hpd a
OUTPUT_HPD A H
page | 163
Advanced Operation
Commands
#gets_output_mode
Returns the video output mode of the specified output. The value returned will be one of
the following:
Value
Description
D
DVI signal detected
H
HDMI signal detected
Syntax
#gets_output_mode output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#gets_output_mode a
OUTPUT_MODE A H
page | 164
Advanced Operation
Commands
#gets_output_rsense
Returns the Rsense state of the specified output(s). The value returned will be one of the
following:
Value
Description
L
Rsense low
H
Rsense high
Syntax
#gets_output_rsense output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Specify 0 to query all outputs;
results are returned in output order A - H.
Example
#gets_output_rsense a
OUTPUT_RSENSE A L
page | 165
Advanced Operation
Commands
#help
Returns a list of available commands. The commands listed are specific to either the
Sender or Receiver unit.
Syntax
#help
Parameters
None
Example
#help
[HELP]
#HELP
[VOLUME]
#GET_MUTE
#GET_VOL
#SET_MUTE
#SET_VOL
[ROUTING]
#GET_MASK
#LOCK_MATRIX
#SET_MASK
R
S
...
...
...
page | 166
Advanced Operation
Commands
#lock_matrix
Locks or unlocks the matrix. This command locks the front panel and the built-in web
interface of the matrix. Note that if the matrix is locked, settings can still be changed using
the command set.
Syntax
#lock_matrix state
Parameters
state
Type: INTEGER
Accepts a number from the table below, specifying the desired state:
state
Description
0
Unlocks the matrix
1
Locks the matrix
Example
#lock_matrix 1
LOCK_MATRIX 1
page | 167
Advanced Operation
Commands
#reboot
Reboots the matrix.
Syntax
#reboot
Parameters
None
Example
#reboot
UNIT WILL REBOOT SHORTLY
Related Commands
#factory_reset
page | 168
Advanced Operation
Commands
#send_custom_edid
Uploads a custom EDID to the specified input. The input must first be set to CUSTOM
MODE.
Syntax
#send_custom_edid input
Parameters
input
Type: INTEGER
The numeric identifier of the input (1 - 8).
Example
#send_custom_edid 1
SEND_COMPLETE
page | 169
Advanced Operation
Commands
#send_hpd
Sends an HPD (Hot-Plug Detect) pulse to the specified input.
Syntax
#send_hpd input
Parameters
input
Type: INTEGER
The identifier of the HDMI input (1 - 8) where the HPD pulse will be sent. Set this
parameter to 0 to send the HPD pulse to all inputs.
Example
#send_hpd 1
HPD SENT
page | 170
Advanced Operation
Commands
#set_audio_output
Sets the analog audio mode for the specifed output(s).
Syntax
#set_audio_output output audtype
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Set this parameter to 0 to set all
outputs to the same audio mode. Feedback lists all analog audio modes for
outputs in order A - H.
audtype
Type: CHAR
The method of how the analog output will be sent to the output. Accepts a value
from the table below.
Type
Description
F
Fixed
V
Variable
Example
#set_audio_output a f
AUDIO OUTPUT A F
Related Commands
#get_audio_output
page | 171
Advanced Operation
Commands
#set_device_desc
Sets the matrix identifier string.
Syntax
#set_device_desc name
Parameters
name
Type: STRING
The device description. This value cannot exceed 30 characters in length.
Example
#set_device_desc matrix8x8
DEVICE DESCRIPTION IS SET TO matrix8x8
Related Commands
#get_device_desc
page | 172
Advanced Operation
Commands
#set_discovery
Enables or disables the “discovery” feature. This feature is enabled by default.
Syntax
#set_discovery state
Parameters
state
Type: INTEGER
Accepts a number from the table below, specifying the desired state:
state
Description
0
Disables “Discovery” mode
1
Enables “Discovery” mode
If set to disabled, then the Syner-G Software Suite will be unable to detect the
matrix on a network. It is recommended that this feature is enabled, until the
matrix has been configured for use on a network.
Example
#set_discovery 0
DISCOVERY 0
Related Commands
#get_discovery
#get_discovery_mode
#set_discovery_mode
page | 173
Advanced Operation
Commands
#set_discovery_mode
Sets the “discovery” mode. This mode is set to read/write by default.
Syntax
#set_discovery_mode mode
Parameters
mode
Type: INTEGER
Accepts a number from the table below, specifying the desired state:
mode
Description
0
Read-only mode
1
Read / write mode
When set to read-only mode, the IP settings for the matrix will be displayed
within the Gefen Syner-G Software Suite but cannot be changed. In order to
both display and allow changes to the IP settings within Gefen Syner-G,
set this feature to read/write mode.
Example
#set_discovery_mode 0
DISCOVERY MODE 0
Related Commands
#get_discovery
#get_discovery_mode
#set_discovery
page | 174
Advanced Operation
Commands
#set_edid_copy
Copies the EDID from output or input to the selected input for use in custom EDID mode.
In order for an EDID to be copied, the destination input port must be set to Custom mode
and must not be locked. See Copying EDID Data (page 89) for more information.
Syntax
#set_edid_copy inout input [...input]
Parameters
inout
Type: INTEGER or CHARACTER
This parameter can accept either the identifier of an HDMI input (1 - 8)
or an HDMI output (A - H). Only a single input or output can be specified
at a time.
input
Type: INTEGER
This parameter must be the identifier of an HDMI input (1 - 8).
Multiple inputs can be specified.
Example
#set_edid_copy a 1
EDID_COPY a 1
#set_edid_copy b 2 5
EDID_COPY b 2 5
Related Commands
#get_edid_lock
#get_edid_mode
#set_edid_lock
#set_edid_mode
page | 175
Advanced Operation
Commands
#set_edid_lock
Locks to unlocks the EDID when using Custom EDID mode. This command only works
if the specified input is set to Custom. See the #set_edid_mode command.
Syntax
#set_edid_lock input state
Parameters
input
Type: INTEGER
This parameter must be the identifier of an HDMI input (1 - 8).
state
Type: INTEGER
Accepts a number from the table below, specifying the desired state:
state
Description
0
Unlock the EDID
1
Lock the EDID
Example
#set_edid_lock 1 0
SET_EDID_LOCK 1 0
Related Commands
#get_edid_lock
#get_edid_mode
#set_edid_copy
#set_edid_mode
page | 176
Advanced Operation
Commands
#set_edid_mode
Sets the EDID mode for the specified input.
Syntax
#set_edid_mode input mode
Parameters
input
Type: INTEGER
This parameter must be the identifier of an HDMI input (1 - 8).
mode
Type: INTEGER
Accepts a number from the table below, corresponding to the desired EDID.
mode
Description
1
UHD 4K 600 MHz 2Ch
2
UHD 4K 600 MHz Multi
3
UHD 4K 300 MHz 2Ch
4
UHD 4K 600 MHz Multi
5
1080P 2Ch
6
1080 Multi
7
External
8
Custom - User
Example
#set_edid_mode 1 2
EDID_MODE 1 2
Related Commands
#get_edid_lock
#get_edid_mode
#set_edid_copy
#set_edid_lock
page | 177
Advanced Operation
Commands
#set_feedback
Enables or disables unsolicited RS-232 feedback.
Syntax
#set_feedback state
Parameters
state
Type: INTEGER
Accepts a number from the table below, specifying the desired state:
state
Description
0
Disable RS-232 feedback
1
Enable RS-232 feedback
Example
#set_feedback 1
SET_FEEDBACK 1
page | 178
Advanced Operation
Commands
#set_gateway
Sets the gateway address for the matrix. The gateway address will be changed only if the
matrix is in static IP mode. If the matrix is using DHCP mode, then the gateway address is
automatically assigned by the DHCP server. The matrix must be rebooted after executing
this command.
Syntax
#set_gateway addr
Parameters
addr
Type: IP ADDRESS
The desired gateway address of the matrix. This address must be entered
in dot-decimal notation.
Example
#set_gateway 10.5.64.1
GATEWAY 10.5.64.1
REBOOT TO APPLY SETTINGS
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_web_port
#set_ip_address
#set_ip_mode
#set_netmask
page | 179
Advanced Operation
Commands
#set_input_hdcp
Sets the HDCP mode on the specified input.
Syntax
#set_input_hdcp input mode
Parameters
input
Type: INTEGER
Accepts the number of an HDMI input (1 - 8). Set this parameter to 0 to apply
the HDCP setting to all inputs. Feedback lists all HDCP settings for inputs in
order 1 - 8.
mode
Type: INTEGER
Accepts a number from the table below, corresponding to the desired HDCP
mode.
mode
Description
0
Reject HDCP content
1
Allow HDCP version 2.2 and below
2
Allow HDCP version 1.4 and below
Example
#set_input_hdcp 1
INPUT_HDCP 1 0
Related Commands
#gets_input_hdcp
#get_output_hdcp
#set_output_hdcp
page | 180
Advanced Operation
Commands
#set_io_name
Sets the name of the specified input.
Syntax
#set_io_name inout name
Parameters
inout
Type: INTEGER or CHARACTER
This parameter can accept either the number of an HDMI input (1 - 8)
or the identifier or an HDMI output (A - H). Only one input or output
can be specified at one time.
name
Type: STRING
The desired name of the specified input / output. The length of the string
cannot exceed 30 characters. Strings greater than 30 characters in length
will be rejected.
Example
#set_io_name 1 Bluray
IO_NAME 1 Bluray
#set_io_name d BIG_screen
IO_NAME D BIG_screen
Related Commands
#get_io_name
page | 181
Advanced Operation
Commands
#set_ip_address
Sets the IP address of the matrix. The matrix must be rebooted after executing this
command.
Syntax
#set_ip_address addr
Parameters
addr
Type: IP ADDRESS
The desired IP address of the matrix. This address must be entered
in dot-decimal notation.
Example
#set_ip_address 10.5.64.81
IP_ADDRESS 10.5.64.81
REBOOT TO APPLY SETTINGS
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_mode
#set_netmask
page | 182
Advanced Operation
Commands
#set_ip_mode
Sets the IP mode of the matrix. The matrix must be rebooted after executing this
command.
Syntax
#set_ip_mode mode
Parameters
mode
Type: INTEGER
Accepts a number from the table below, corresponding to the desired IP mode.
mode
Description
0
Static
1
DHCP
2
Auto
Example
#set_ip_mode 1
IP MODE 1
REBOOT TO APPLY SETTINGS
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_netmask
page | 183
Advanced Operation
Commands
#set_ir_channel
Sets the IR channel of the matrix. In order to use the included IR remote control with the
matrix, both the matrix and the IR remote control must be set to the same IR channel.
Syntax
#set_ir_channel irch
Parameters
irch
Type: INTEGER
Accepts a number from the table below, corresponding to the desired IR channel.
irch
Description
1
IR channel 1
2
IR channel 2
3
IR channel 3
4
IR channel 4
Example
#set_ir_channel 2
IR_CHANNEL 2
Related Commands
#get_ir_channel
page | 184
Advanced Operation
Commands
#set_lcd_brightness
Sets the brightness level of the LCD display on the front panel of the matrix.
Syntax
#set_lcd_brightness level
Parameters
level
Type: INTEGER
Accepts a number within the range of 0 - 100. The value of 100 represents
the brightest setting of the display.
Example
#set_lcd_brightness 75
LCD_BRIGHTNESS 75
Related Commands
#get_lcd_brightness
page | 185
Advanced Operation
Commands
#set_mask
Sets the masking for the specified output(s).
Syntax
#set_mask output state
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Set this parameter to 0 to set all
outputs to the same masking state. Feedback lists all output masking states in
order A - H.
state
Type: INTEGER
The masking state. Accepts a value from the table below.
State
Description
0
Unmask
1
Mask
Example
#set_mask a 1
MASK A 1
Related Commands
#get_mask
page | 186
Advanced Operation
Commands
#set_mute
Sets the audio muting state for the specified output(s).
Syntax
#set_mute output
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Set this parameter to 0 to set all
outputs to the same muting state. Feedback lists all output muting states in order
A - H.
state
Type: INTEGER
The muting state. Accepts a value from the table below.
State
Description
0
Unmute
1
Mute
Example
#set_mute a 0
MUTE A 0
Related Commands
#get_mute
page | 187
Advanced Operation
Commands
#set_netmask
Sets the network mask address. The matrix must be rebooted after executing this
command.
Syntax
#set_netmask addr
Parameters
addr
Type: ADDRESS
The desired subnet mask of the matrix. This address must be entered
in dot-decimal notation.
Example
#set_netmask 255.255.255.0
NETMASK 255.255.255.0
REBOOT TO APPLY SETTINGS
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_web_port
#set_ip_address
#set_ip_mode
page | 188
Advanced Operation
Commands
#set_output_hdcp
Sets the HDCP mode on the specified output.
Syntax
#set_output_hdcp output mode
Parameters
output
Type: CHARACTER
Accepts the identifier of an HDMI output (A - H). Set this parameter to 0 to set
all outputs to the same HDCP mode. Feedback lists all HDCP mode for outputs
in order A - H.
mode
Type: INTEGER
Accepts a number, from table below, corresponding to the desired HDCP mode.
mode
Description
0
Follow Input
1
Always Encode
Example
#set_output_hdcp a 0
OUTPUT_HDCP A 0
Related Commands
#gets_input_hdcp
#get_output_hdcp
#set_input_hdcp
page | 189
Advanced Operation
Commands
#set_preset_name
Assigns a name to the specified preset.
Syntax
#set_present_name preset name
Parameters
preset
Type: INTEGER
Accepts the identifier of a Preset (1 - 16).
name
Type: STRING
The name of the preset. The name must not exceed 12 characters in length.
No special characters (e.g. #,@,*,&,%, etc.) are allowed. Spaces are permitted.
Example
#set_preset_name 1 LivingRoom
PRESET_NAME 1 LivingRoom
Related Commands
#get_preset_name
page | 190
Advanced Operation
Commands
#set_remote_udp_access
Enables or disables remote UDP access.
Syntax
#set_remote_udp_access state
Parameters
state
Type: INTEGER
Accepts a number from the table below, corresponding to the desired state.
state
Description
0
Disable remote UDP access
1
Enable remote UDP access
Example
#set_remote_udp_access 0
REMOTE_UDP_ACCESS 0
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 191
Advanced Operation
Commands
#set_remote_udp_ip
Sets the remote UDP IP address of the matrix.
Syntax
#set_remote_udp_ip addr
Parameters
addr
Type: IP ADDRESS
The desired remote UDP IP address of the matrix. The address must be
entered in dot-decimal notation.
Example
#set_remote_udp_ip 192.168.1.251
REMOTE_UDP_IP 192.168.1.251
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_port
#set_udp_access
#set_udp_port
page | 192
Advanced Operation
Commands
#set_remote_udp_port
Sets the remote UDP listening port for the matrix.
Syntax
#set_remote_udp_port port
Parameters
port
Type: INTEGER
The desired remote UDP port (0 - 65535) of the matrix.
Example
#set_remote_udp_port 50008
REMOTE_UDP_PORT 50008
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_udp_access
#set_udp_port
page | 193
Advanced Operation
Commands
#set_showme
Enables or disables the “Show Me” feature. If the “Show Me” feature is enabled,
then all the buttons (with the exception of the Power button), will flash slowly.
This feature allows the matrix to be visually identified on the network and is useful
when multiple matrix units are being used. The default setting is disabled.
Syntax
#set_showme state
Parameters
state
Type: INTEGER
Accepts a number from the table below, corresponding to the desired state.
state
Description
0
Disable “Show Me”
1
Enable “Show Me”
Example
#set_showme 1
SET_SHOWME 1
Related Commands
#get_discovery
#set_discovery
page | 194
Advanced Operation
Commands
#set_telnet_access
Enables or disables Telnet access on the matrix.
Syntax
#set_telnet_access state
Parameters
state
Type: INTEGER
Accepts a number from the table below, corresponding to the desired state.
state
Description
0
Disable Telnet access
1
Enable Telnet access
Example
#set_telnet_access 1
TELNET_ACCESS 1
Related Commands
#get_telnet_access
#get_telnet_port
#get_telnet_message
#set_telnet_port
#set_telnet_message
page | 195
Advanced Operation
Commands
#set_telnet_login
Enable or disable the Telnet login process. When disabled, login credentials are not
required.
Syntax
#set_telnet_login state
Parameters
state
Type: INTEGER
Accepts a number, from table below, corresponding to the desired state.
state
Description
0
Disable login process
1
Enable login process
Example
#set_telnet_login
Related Commands
#get_telnet_access
#get_telnet_port
#get_telnet_message
#set_telnet_access
#set_telnet_message
page | 196
Advanced Operation
Commands
#set_telnet_message
Enables or disables the Telnet welcome message.
Syntax
#set_telnet_message state
Parameters
state
Type: INTEGER
Accepts a number, from table below, corresponding to the desired state.
state
Description
0
Disable welcome message
1
Enable welcome message
Example
#set_telnet_message
Related Commands
#get_telnet_access
#get_telnet_port
#get_telnet_message
#set_telnet_access
#set_telnet_port
page | 197
Advanced Operation
Commands
#set_telnet_port
Sets the Telnet listening port on the matrix.
Syntax
#set_telnet_port port
Parameters
port
Type: INTEGER
The desired remote Telnet listening port (0 - 65535) of the matrix.
Example
#set_telnet_port 23
TELNET_PORT 23
Related Commands
#get_telnet_access
#get_telnet_port
#get_telnet_message
#set_telnet_access
#set_telnet_message
page | 198
Advanced Operation
Commands
#set_udp_access
Enables or disables UDP access.
Syntax
#set_udp_access state
Parameters
state
Type: INTEGER
Accepts a number, from table below, corresponding to the desired state.
state
Description
0
Disable UDP access
1
Enable UDP access
Example
#set_udp_access 0
UDP_ACCESS 0
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_port
page | 199
Advanced Operation
Commands
#set_udp_port
Sets the local UDP listening port.
Syntax
#set_udp_port port
Parameters
port
Type: INTEGER
The desired UDP listening port (0 - 65535) of the matrix.
Example
#set_udp_port 50007
UDP_PORT 50007
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
page | 200
Advanced Operation
Commands
#set_vol
Sets the analog output volume level for the specified output(s).
Syntax
#set_vol output level
Parameters
output
Type: CHAR / INTEGER
The alphabetic identifier of the output (A - H). Set this parameter to 0 to set all
outputs to the same volume level. Feedback lists all volume levels for outputs in
order A - H.
level
Type: INTEGER
The desired volume level (0 - 100).
Example
#set_vol a 100
VOL A 100
Related Commands
#get_vol
page | 201
Advanced Operation
Commands
#set_web_port
Sets the HTTP listening port for the matrix.
Syntax
#set_gateway port
Parameters
port
Type: INTEGER
The desired HTTP listening port for the matrix.
Example
#set_gateway 192.168.1.1
GATEWAY 192.168.1.1
Related Commands
#get_gateway
#get_web_port
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_mac_addr
#get_netmask
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
page | 202
Advanced Operation
Commands
p
Recalls the specified routing preset.
Syntax
p preset
Parameters
preset
Type: INTEGER
The number of a preset (1 - 16).
Example
p 10
P 10
Related Commands
r
page | 203
Advanced Operation
Commands
r
Routes the specified input to the one or more specified outputs.
Syntax
r input output [...output]
Parameters
input
Type: INTEGER / CHAR
The number of an HDMI input (1 - 8). This parameter also accepts a character
argument of “X”. The “X” argument is not case-sensitive. If “X” is
specified, then no input is selected. To “turn on” an input that is marked as
“X”, use an HDMI input (1 - 8) as the argument.
output
Type: CHARACTER
The identifier or an HDMI output (A - H). More than one output may be specified.
Set this parameter to 0 to route the input to all outputs.
Examples
R 1 A
R A 1
R X A
R A X
R 1 A B C
R A 1 B 1 C 1
R 1 0
R A 1 B 1 C 1 D 1 E 1 F 1 G 1 H 1
Related Commands
p
page | 204
Advanced Operation
Commands
s
Returns the routing state for all inputs / outputs. “X” will be displayed when the output is
selected to input off.
Syntax
s
Parameters
None
Example
s
S A 1 B 2 C 3 D X E 0 F X G 1 H 0
Related Commands
r
page | 205
This page left intentionally blank.
600 MHz
4K ULTRA
8x8 Matrix
w/HDR and Audio De-Embedder
4
Appendix
page | 207
Appendix
Network Cable Diagram
Front of RJ-45 Connector
1 2 3 4 5 6 7 8
Gefen recommends the TIA/EIA-568-B wiring option. Use the table below when
field-terminating cable for use with Gefen products.
Pin
Color
Description
1
Orange / White
TD+ (Transmit Data, positive differential signal)
2
Orange
TD- (Transmit Data, negative differential signal)
3
Green / White
RD+ (Receive Data, positive differential signal)
4
Blue
Unused
5
Blue / White
Unused
6
Green
RD- (Receive Data, negative differential signal)
7
Brown / White
Unused
8
Brown / White
Unused
Information
Shielded CAT-5e (or better) cabling is recommended.
page | 208
Appendix
Default Settings
Description
Setting
MAC Address
Device-dependent (cannot be modified)
IP Address
192.168.1.72
Subnet Mask
255.255.255.0
Default Gateway
192.168.1.1
HTTP Listening Port
80
Telnet Listning Port
23
Telnet / TCP Access
Enabled
UDP Port
50007
Enable UDP Access
Disabled
Remote UDP IP Address
192.168.1.255
Remote UDP Port
50008
Remote UDP Access
Disabled
Default Administrator Password
Admin
Default Operator Password
Operator
Gefen Syner-G Discovery
Enabled
Gefen Syner-G Discovery Mode
Read / Write
Gefen Syner-G Show Device
Hide Me
Description
Setting
Output Names
Output A - Output H
A/V Input Names
Input 01 - Input 08
HDCP (each input)
Version 2.2 and below
HDCP (each output)
Follow Input
EDID (each input)
Internal UHD 4K 600Mhz 2Ch
RS-232 Feedback
On
LED Brightness
50
IR Channel
1
Routing
Input 01 > Output A
Input 02 > Output B
Input 03 > Output C
Input 04 > Output D
Input 05 > Output E
Input 06 > Output F
Input 07 > Output G
Input 08 > Output H
Preset Names
Preset01 - Preset16
Matrix Lock
Disabled
page | 209
Appendix
Internal EDID Profiles
720p 2-channel audio
Video data block
1280x720p @ 60Hz
1280x720p @ 50Hz
640x480p @ 60Hz
720x480p @ 60Hz
720x480p @ 60Hz
1440x480p @ 60Hz
1440x480p @ 60Hz
720x576p @ 50Hz
1440x480i @ 60Hz
1440x480i @ 60Hz
720x576p @ 50Hz
1440x576i @ 50Hz
1440x576i @ 50Hz
1440x576p @ 50Hz
1440x576p @ 50Hz
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(4:3)
(16:9)
(4:3)
(4:3)
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 48 44.1 32
Supported sample sized (bits): 24 20 16
720p Multichannel audio
Video data block
640x480p @ 60Hz
720x480p @ 60Hz
720x480p @ 60Hz
1280x720p @ 60Hz
1440x480i @ 60Hz
720x576p @ 50Hz
720x576p @ 50Hz
1280x720p @ 50Hz
1440x576i @ 50Hz
(4:3)
(4:3)
(4:3)
(native)
(4:3)
(4:3)
(16:9)
(16:9)
(4:3)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 48 44.1 32
Supported sample sized (bits): 24 20 16
page | 210
Appendix
Internal EDID Profiles
1080p 2-channel audio
Video data block
640x480p
@ 60Hz
720x480p
@ 60Hz
720x480p
@ 60Hz
1280x720p @ 60Hz
1920x1080i @ 60Hz
1440x480i @ 60Hz
1440x480i @ 60Hz
1440x480p @ 60Hz
1440x480p @ 60Hz
720x576p
@ 50Hz
720x576p
@ 50Hz
1280x720p @ 50Hz
1920x1080i @ 50Hz
1440x576i @ 50Hz
1440x576i @ 50Hz
1440x576p @ 50Hz
1440x576p @ 50Hz
1920x1080p @ 50Hz
1920x1080p @ 24Hz
1920x1080p @ 25Hz
1920x1080p @ 30Hz
1920x1080i @ 50Hz
1280x720p @ 24Hz
1280x720p @ 25Hz
1280x720p @ 30Hz
1920x1080p @ 60Hz
(4:3)
(16:9)
(16:9)
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 48 44.1 32
Supported sample sized (bits): 24 20 16
page | 211
Appendix
Internal EDID Profiles
1080p Multichannel audio
Video data block
640x480p
@ 60Hz
720x480p
@ 60Hz
720x480p
@ 60Hz
1280x720p @ 60Hz
1920x1080i @ 60Hz
1440x480i @ 60Hz
1440x480i @ 60Hz
1440x480p @ 60Hz
1440x480p @ 60Hz
720x576p
@ 50Hz
720x576p
@ 50Hz
1280x720p @ 50Hz
1920x1080i @ 50Hz
1440x576i @ 50Hz
1440x576i @ 50Hz
1440x576p @ 50Hz
1440x576p @ 50Hz
1920x1080p @ 50Hz
1920x1080p @ 24Hz
1920x1080p @ 25Hz
1920x1080p @ 30Hz
1920x1080i @ 50Hz
1280x720p @ 24Hz
1280x720p @ 25Hz
1280x720p @ 30Hz
1920x1080p @ 60Hz
(4:3)
(16:9)
(16:9)
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(16:9)
(16:9)
(4:3)
(16:9)
(4:3)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 192 176.4 96 88.2 48 44.1 32
Supported sample sizes (bits): 24 20 16
Linear PCM
Max channels: 8
Supported sample rates (kHz): 48 44.1 32
Supported sample sizes (bits): 24 20 16
DTS
Max channels: 6
Supported sample rates (kHz): 48 44.1
Maximum bit rate: 0 kHz
AC-3
Max channels: 6
Supported sample rates (kHz): 48 44.1 32
Maximum bit rate: 640 kHz
Enhanced AC-3
Max channels: 8
Supported sample rates (kHz): 48 44.1
page | 212
Appendix
Internal EDID Profiles
4K 2-channel audio
Video data block
720x480p
@ 60Hz
1280x720p @ 60Hz
1920x1080i @ 60Hz
1440x480i @ 60Hz
1920x1080p @ 60Hz
720x576p
@ 50Hz
1280x720p @ 50Hz
1920x1080i @ 50Hz
1440x576i @ 50Hz
1920x1080p @ 50Hz
1920x1080p @ 24Hz
1920x1080p @ 25Hz
1920x1080p @ 30Hz
3840x2160p @ 24Hz
3840x2160p @ 25Hz
3840x2160p @ 30Hz
3840x2160p @ 50Hz
3840x2160p @ 60Hz
4096x2160p @ 24Hz
4096x2160p @ 25Hz
4096x2160p @ 30Hz
4096x2160p @ 50Hz
4096x2160p @ 60Hz
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(256:135)
(256:135)
(256:135)
(256:135)
(256:135)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 192 176.4 96 88.2 48 44.1 32
Supported sample sizes (bits): 24 20 16
page | 213
Appendix
Internal EDID Profiles
4K multichannel audio
Video data block
720x480p
@ 60Hz
1280x720p @ 60Hz
1920x1080i @ 60Hz
1440x480i @ 60Hz
1920x1080p @ 60Hz
720x576p
@ 50Hz
1280x720p @ 50Hz
1920x1080i @ 50Hz
1440x576i @ 50Hz
1920x1080p @ 50Hz
1920x1080p @ 24Hz
1920x1080p @ 25Hz
1920x1080p @ 30Hz
3840x2160p @ 24Hz
3840x2160p @ 25Hz
3840x2160p @ 30Hz
3840x2160p @ 50Hz
3840x2160p @ 60Hz
4096x2160p @ 24Hz
4096x2160p @ 25Hz
4096x2160p @ 30Hz
4096x2160p @ 50Hz
4096x2160p @ 60Hz
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(16:9)
(256:135)
(256:135)
(256:135)
(256:135)
(256:135)
Audio data block
Linear PCM
Max channels: 2
Supported sample rates (kHz): 48 44.1 32
Supported sample sizes (bits): 24 20 16
Linear PCM
Max channels: 8
Supported sample rates (kHz): 96 48 44.1
Supported sample sizes (bits): 24 20 16
AC-3
Max channels: 6
Supported sample rates (kHz): 48
Maximum bit rate: 640 kHz
Enhanced AC-3
Max channels: 8
Supported sample rates (kHz): 192 96 48 44.1
MAT (MLP)
Max channels: 1
Supported sample rates (kHz): 192 96 48 44.1
DTS
Max channels: 6
Supported sample rates (kHz): 96 48 44.1
Maximum bit rate: 1536 kHz
DTS-HD
Max channels: 8
Supported sample rates (kHz): 192 96 48
page | 214
Appendix
Specifications
Supported Formats
Resolutions (max.)
•
•
•
•
4096 x 2160 at 60 Hz (4:4:4)
3860 x 2160 at 60 Hz (4:4:4)
1080p Full HD
1920 x 1200 (WUXGA) at 60 Hz
HDMI Input Connectors
•
8 x Type A 19-pin female, locking
HDMI Output Connectors
•
8 x Type A 19-pin female, locking
Digital Audio Output Connectors
•
•
8 x TOSLINK® Optical
8 x RCA Coaxial
Analog L/R Audio Output Connectors
•
8 x 3.5mm mini-stereo jack
RS-232 serial port
•
1 x DB-9, female
Ethernet (IP Control)
•
1 x RJ-45
Front-panel display
•
1 x OLED (2x rows, 20 chars / row)
Power Button / Indicator
•
1 x Tact-type, bi-color blue/orange
backlight
Control Buttons / Indicators
•
9 x Tact-type
Reset Button
•
1 x Tact-type, recessed
IR Sensor
•
1 x located on front panel
IR In/Ext Port
•
1 x 3.5mm mini-stereo jack
IR Extender type
•
EXT-RMT-EXTIRN
DC Power Connector
•
1 x 4-pin, locking
Power Supply
•
24V DC
Maximum TMDS Clock
•
600 MHz
Total Signal Bandwidth / Data Rate
•
18 Gbps
Power Supply
•
24V DC
Power Consumption
•
45 W
Operating Temperature
•
+32 to +122 ºF (0 to +50 ºC)
Operating Humidity
•
5% to 90% RH, non-condensing
Storage temperature
•
-4 to +185 ºF (-20 to +85 ºC)
Storage humidity
•
0% to 95% RH, non-condensing
MTBF
•
50000 hours
Connectors, Controls, and Indicators
Operational
page | 215
Appendix
Specifications
Physical
Rack-mount requirements
•
Standard 19” rack, 2U high
Dimensions (excluding rack ears and
connectors, W x H x D)
•
17.25” x 3.5” x 15.75”
(440mm x 89mm x 400mm)
Net Unit Weight
•
21 lbs (9.5 kg)
Shipping Weight
•
29 lbs (13.25 kg)
Features and specifications are subject to change without notice.
All trademarks and registered trademarks are the property of their respective owners.
Copyright© 2017 Core Brands, LLC.
page | 216
Appendix
Index
A
Accessing the Menu System 31
Application diagram 11
Audio
muting / unmuting 23
volume, adjusting 21
C
Commands 114
#factory_reset 118, 119
#get_device_desc 120, 121
#get_discovery 122
#get_discovery_mode 123
#get_edid_lock 124
#get_edid_mode 125
#get_gateway 126, 129
#get_http_port 157
#get_input_hdcp 158, 160, 161, 162
#get_io_name 133
#get_ip_address 134
#get_ipconfig 136
#get_ip_mode 135
#get_ir_channel 137
#get_lcd_brightness 138
#get_mac_addr 139
#get_netmask 142
#get_output_hdcp 144
#get_preset_name 145
#get_remote_udp_access 146
#get_remote_udp_ip 147
#get_remote_udp_port 148
#get_telnet_access 150
#get_telnet_port 153
#get_telnet_welcome 152
#get_udp_access 154
#get_udp_port 155
#help 166
#lock_matrix 167
p 203
r 204
#reboot 168
#send_hpd 170
#set_device_desc 172
#set_discovery 173
#set_discovery_mode 174
#set_edid_copy 175
#set_edid_lock 176
#set_edid_mode 177
#set_feedback 178
#set_gateway 179
#set_http_port 202
#set_input_hdcp 180
#set_io_name 181
#set_ip_address 182
#set_ip_mode 183
#set_ir_channel 184
#set_lcd_brightness 185
#set_netmask 188
#set_output_hdcp 189
#set_preset_name 190
#set_remote_udp_access 191
#set_remote_udp_ip 192
#set_remote_udp_port 193
#set_showme 194
#set_telnet_access 195
#set_telnet_port 198
#set_telnet_welcome 197
#set_udp_access 199
#set_udp_port 200
Connection instructions 10
D
Default Settings 209
Discovery Settings 100
E
EDID
copying EDID data 89
custom EDID 88
downloading EDID data 92
EDID mode 87
getting EDID information 91
internal EDID profiles 210
uploading EDID data 94
F
Features vii
Firmware Update 104
Front Panel
description 2
Front Panel Controls
accessing the menu system 31
HPD control 35
IP settings
page | 217
Index
Appendix
gateway 46
HTTP port 47
IP address 44
IP mode 44
subnet mask 45
IR channel 62
LCD brightness 60
locking the matrix
using the IR remote control
routing
using the IR remote control
routing presets
using the front panel 29
using the IR remote control
Telnet settings 48
TCP access 49
TCP port 50
welcome message 51
UDP settings
remote UDP access 54
remote UDP address 55
UDP access 52
UDP listening port 53
unlocking the front panel
using the IR remote control
H
HDCP Control 85
HPD Control 35, 84
I
IP Settings
gateway 46
IP address 44
IP mode 44
subnet mask 45
IR Remote Control
description 5
installing batteries 8
setting the IR channel 9
L
Licensing vi
Locking the Matrix
using the IR remote control 28
M
28
20
30
Masking
outputs 77
Matrix
application diagram 10
configuration 12
connections 10
Menu System
accessing 31
Muting
audio outputs 23
N
Network
cable diagram 208
Discovery settings 100
IP settings 95
TCP / Telnet settings 96
Web login settings 99
28
O
Operating Notes v
Output
volume, adjusting 21
P
Packing List viii
Panel
front 2
rear 3
Password
default 97
setting 97
R
Rear Panel
description 3
Routing
using the IR remote control 20
RS-232
configuration 113
feedback 101
page | 218
Appendix
Index
logging in 68
tabs and sub-tabs 70
LCD brightness 101
locking the matrix 73
masking outputs 77
rebooting the matrix 108
Restoring configuration 103
routing 75
RS-232 feedback 101
setting the EDID mode 87
custom EDID 88
setting the IR channel 106
updating firmware 104
viewing the routing status 74
S
Safety Instructions ii
Selecting Routing Presets
using the front panel 29
Specifications 215
Syner-G
configuring the matrix 12
T
Table of Contents ix
TCP / Telnet Settings
TCP access 49
TCP listening port 50
welcome message 51
Technical Support iv
U
UDP
configuration 112
remote UDP access 54, 98
remote UDP address 55, 98
UDP listening port 53, 98
Unlocking the matrix
using the IR remote control 28
Unmuting
audio outputs 23
V
Volume
muting / unmuting 23
output, adjusting 21
W
Warranty Information iii
Web Interface
changing input and output names 82
downloading configuration 102
factory reset 107
HDCP 85
HPD control 84
input and output status 81
introduction 68
buttons 70
page | 219
*Preferred
1800 S McDowell Blvd. Petaluma CA 94954
(707) 283-5900 (800) 472-5555
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising