Gefen | EXT-UHD-LANS-TX | Gefen EXT-UHD-LANS-RX Manual | Gefen EXT-UHD-LANS-TX 4K Ultra HD HDMI over IP - Sender Package Manual

Gefen EXT-UHD-LANS-TX 4K Ultra HD HDMI over IP - Sender Package Manual
Gen 2.0
4K Ultra HD
HDMI over IP
EXT-UHD-LANS-TX
EXT-UHD-LANS-RX
User Manual
Version A2
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install or place this product near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15.
Batteries that may be included with this product and/or accessories should never be
exposed to open flame or excessive heat. Always dispose of used batteries
according to the instructions.
2
Warranty Information
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Connect section of the Gefen website at http://www.gefen.com/connect/warranty-andreturn-policy
3
Contact Us
Technical Support
1-707-283-5900
1-800-472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacific Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Nortek Security & Control, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
© 2018 Nortek Security & Control, LLC. All Rights Reserved.
All trademarks are the property of their respective owners.
Gefen and Nortek Security & Control, LLC reserve the right to make changes in the hardware,
packaging, and any accompanying documentation without prior notice.
4
Operating Notes
Important
•
When connecting through a Local Area Network, a managed gigabit switch is required.
Jumbo Frame Support (8k or greater) and IGMP Snooping must be enabled.
•
A dedicated LAN is not required but highly recommended.
•
Only the HDMI and DisplayPort™ Inputs and Outputs will pass content from HDCPencoded sources such as Blu-ray players and PlayStation® console systems. Other formats
do not support HDCP content. If HDCP encrypted content is being passed, the output
will not be active.
•
We recommend that Sender and Receiver are first connected directly and functionality/
performance is fully verified before integrating them into a Local Area Network.
•
Always make sure that all units within a system are running the latest firmware.
•
This product has been specifically designed for use with the Gefen Syner-G™ Software
Suite, available for download at www.gefen.com. The Gefen Syner-G™ Discovery and
Show-Me features simplify initial IP configuration
•
Gefen highly recommends the Gefen EXT-CU-LAN Matrix Controller for setting up and
controlling the operation of an AV-over-IP network using these products. Alternatively,
the Syner-G™ software can be used for IP configuration and firmware updates.
•
Shielded CAT-5e (or better) cables used between the Sender and the Receiver unit or
between each unit and the IP switch, should not exceed 330 feet (100 meters).
•
By default, all Sender and Receiver units are set to channel 0.
•
The HDMI inputs and outputs on these products also support Single-Link DVI and its
standard VESA resolutions. Dual-Link DVI is not supported.
•
By default, each device is setup in unicast mode and the source device will use the EDID
from the display (or other sink device) which is connected to the Receiver unit.
•
If terminating network cables in the field, please adhere to the TIA/EIA568B
specification. See the Network Cable Diagram (page 158) for details.
This product uses UL-Listed power supplies
5
Operating Notes
Licensing
This product uses software that is subject to open source licenses, including one or more of
the General Public License Version 2 and Version 2.1, Lesser General Public License Version 2.1
and Version 3, BSD, and BSD-style licenses. Distribution and use of this product is subject
to the license terms and limitations of liability provided in those licenses. Specific license
terms and Copyright Notifications are provided in the source code. For three years from
date of activation of this product, any party may request, and we will supply, for software
covered by an applicable license (e.g. GPL or LGPL), a complete machine-readable copy of the
corresponding open source code on a medium customarily used for software interchange.
The following software and libraries are included with this product and subject to their
respective open source licenses:
•
•
jQuery
Linux
6
Features & Packing List
Features
•
Extends HDMI, RS-232, analog audio, and IR, using a Gigabit Local Area Network
•
Independent video, RS-232, IR, and audio routing**
•
Backward-compatible with first generation Gefen AV over IP products
•
Supports input resolutions up to 4K 60Hz 4:2:0
•
Supports output resolutions up to 4K 30Hz 4:4:4
•
Supported HDMI Features:
HDR
HDCP 2.2 and 1.4
Deep Color
Lip-Sync
Uncompressed LPCM digital audio up to 7.1 channels
Up to 7.1 channels of HBR (High Bit Rate) digital audio including Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™
•
When used with Gefen DVI-to-HDMI cables (not included), supports the use of DVI
sources and DVI displays up to 1080p Full HD and 1920x1200 (WUXGA)
•
Integrated scaler ensures maximum compatibility and best possible viewing experience
with different contents and displays
•
Built-in video wall controller accommodates any number of rows and columns up to
16x16
•
Built-in Audio De-Embedder on Receiver breaks out 2 channel analog, 2 channel PCM,
and up to 5.1 channels of Bitstream audio from the HDMI signal, allowing the audio
content to be sent to external amplifiers and music distribution systems for added
impact
•
MFU (Mass-Firmware-Update), quick and automated configuration, and enhanced
control capabilities and system security when used with the Gefen EXT-CU-LAN Matrix
Controller
•
Enhanced API for added functionality with third-party control systems
•
Built-in web interface, Telnet, and UDP
•
Compatible with the Gefen Keyboard Switching Controller software, available for
download at www.gefen.com
•
Supports 39,900 Senders and a combination of over 65,000 Sender and Receiver units,
depending on the network bandwidth and number of ports on your network switch
* Features and specifications are subject to change without notice.
** Pending features to be activated via an upcoming firmware update.
All trademarks and registered trademarks are properties of their respective owners.
7
Features & Packing List
•
802.3af standard Power-over-Ethernet allows the Sender and Receiver units to be
powered through a standard PoE-enabled IP network switch, without the need for
external power supplies
•
Two-port Gigabit Ethernet switch built into the Receiver unit
•
Mode switch on Sender for sharpness or motion-optimization of image
•
Field-updatable firmware via EXT-CU-LAN controller or the built-in web server interface
•
Locking power supply connectors
•
Low-profile, half-rack width Sender and Receiver enclosures are rack-mountable using
EXT-RACK-1U-GRY
•
Sender and Receiver can also be surface-mounted using the included L-brackets
•
Low profile Receiver enclosure features an IR Extender port and can be hidden away
behind the display
•
* Features and specifications are subject to change without notice.
** Pending features to be activated via an upcoming firmware update.
All trademarks and registered trademarks are properties of their respective owners.
8
Features & Packing List
Packing List - Sender unit
The following items are included in the Sender Unit package. If any of these items are not
present in the box when you first open it, please contact Gefen Technical Support as soon as
possible.
(1)
(1)
(1)
(1)
(4)
(2)
(4)
(2)
(1)
EXT-UHD-LANS-TX - Sender unit
5V 2.6A Power Supply
3.5mm-to-DB-9 Adaptor, M-F (ADA-MP-2-DB9-MF-AB)
IR Emitter (EXT-IREMIT)
Self-Adhesive Rubber-Feet
L-Shaped Mounting Brackets
Machine screws for L-Shaped Mounting Brackets
Machine screws for EXT-RACK-1U-GRY (sold separately)
Quick-Start Guide
Packing List - Receiver unit
The following items are included in the Receiver Unit package. If any of these items are not
present in the box when you first open it, please contact Gefen Technical Support as soon as
possible.
(1)
(1)
(1)
(1)
(4)
(2)
(4)
(2)
(1)
EXT-UHD-LANS-RX - Receiver unit
5V 2.6A Power Supply
3.5mm-to-DB-9 Adaptor, M-M (ADA-MP-2-DB9-MM-AB)
IR Extender Module (EXT-RMT-EXTIRN)
Self-Adhesive Rubber-Feet
L-Shaped Mounting Brackets
Machine screws for L-Shaped Mounting Brackets
Machine screws for EXT-RACK-1U-GRY (sold separately)
Quick-Start Guide
9
Table of Contents
Introduction.................................................................................................................... 12
Sender Unit............................................................................................................................. 12
Receiver Unit.......................................................................................................................... 14
Installation......................................................................................................................17
Local Area Network (LAN) Connection................................................................................. 17
Using a Direct Connection.....................................................................................................22
Supplementary Connections.................................................................................................24
Sample Wiring Diagram........................................................................................................25
LED Status.......................................................................................................................26
Link.........................................................................................................................................26
Power......................................................................................................................................26
Setting the Video Channel............................................................................................ 27
Setting the Channel using the Web Interface......................................................................27
Setting the Channel using the Front Panel...........................................................................28
Blocking & Masking Video.............................................................................................31
Unicast & Multicast Modes........................................................................................... 33
Configuring Unicast Mode..................................................................................................... 33
Switching between Sender units in Unicast mode............................................................... 35
Configuring Multicast Mode.................................................................................................38
Discovery Mode..............................................................................................................40
Gefen Syner-G Discovery...................................................................................................... 40
Finding Your Device............................................................................................................... 41
RS-232 Control................................................................................................................43
RS-232 under Unicast Mode..................................................................................................45
RS-232 under Multicast Mode...............................................................................................45
Audio Connections.........................................................................................................46
Audio Sources and De-Embedding.......................................................................................47
Creating Video Walls.....................................................................................................48
Wall Size and Layout..............................................................................................................48
Bezel Compensation..............................................................................................................50
Setting the Video Mode..................................................................................................51
Using the Web interface........................................................................................................ 51
Changing the Password................................................................................................. 52
10
Table of Contents
Utilities............................................................................................................................ 53
Reset using the Web Interface.............................................................................................. 53
Reboot using the Web Interface........................................................................................... 55
Reboot using the Front Panel................................................................................................56
Telnet Access................................................................................................................... 57
Commands...................................................................................................................... 58
Discovery Service....................................................................................................................58
Help........................................................................................................................................58
Network..................................................................................................................................58
Routing...................................................................................................................................59
RX Specific............................................................................................................................. 60
Serial........................................................................................................................................61
System.....................................................................................................................................61
TX Specific.............................................................................................................................. 61
Video.......................................................................................................................................62
Web Interface.........................................................................................................................62
Network Cable Diagram.............................................................................................. 158
Rack Tray Installation.................................................................................................. 159
Specifications*.............................................................................................................. 160
11
EXT-UHD-LANS-TX
Introduction
Sender Unit
2
1
3
4
5
6
On
Power
Link
Reset
Mode
Prog
Off
Prog Sel
On
Power
Link
Reset
7
8
Mode
Prog
9
Off
Prog Sel
11
10
12
13
EXT-UHD-LANS-TX
EXT-UHD-LANS-TX
LAN (PoE)
5V DC
LAN (PoE)
5V DC
RS-232
RS-232
IR In/Ext
IR Out
IR In/Ext
IR Out
HDMI In
HDMI In
Line In
Line In
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver.
3
Reset
Press this button, using the end of a paper clip
or other pointed object, to perform a soft reset.
4
Mode
Press this button, using the end of a paper clip
or other pointed object, to toggle between
Graphic and Video modes.
5
Prog
This button
is used
for device
4K Ultra HD
HDMI
over
IP -recovery
Sender
operations, in the event of a firmware update
4K Ultra HD
HDMI
or other
failure. over IP - Sender
12
Introduction
ID
Name
Description
6
Prog Sel
For normal operation, this switch should be in
the Off position. Setting this switch to the On
position, places the unit in the ready-state for
firmware recovery or debug operations.
7
5V DC
This power receptacle is used to connect the
included 5V DC power supply. An external
power supply is not required when connecting
to a PoE-enabled switch using the LAN (PoE)
port.
8
LAN (PoE)
Connect a CAT-5e or better cable up to 330
feet/100 meters, from this port to a PoEcapable network switch. If a PoE switch is
not available or the Sender and Receiver are
connected directly, then the included 5V DC
power supply must be connected to the Sender
unit.
9
RS-232
Using the included 3.5mm-to-Female-DB-9
adapator, connect an DB-9 cable from this port
to a RS-232 automation control unit. See RS232 Control (page 43) for more information.
10
IR In/Ext
Connect an IR Extender (Gefen part no.
EXT-RMT-EXTIRN) to this port. Alternatively,
connect a 3.5mm mini-stereo connector
from this port to the electrical IR output of
an automation control system.
11
IR Out
Connect an IR Emitter (Gefen part no. EXTIREMIT) from this port to the IR sensor of the
device to be controlled.
12
HDMI In
Use a Gefen CAB-HD-LCK-xxMM Locking
HDMI cable to the connect an AV source to
this port.
13
Line In
Connect a 3.5mm mini-stereo cable from this
port to the analog audio source.
13
EXT-UHD-LANS-RX
Introduction
Receiver Unit
2
1
3
4
5
On
Power
Link
Reset
Prog
Power
Link
Reset
7
Prog
CH
+
–
CH
+
Off
Prog Sel
On
6
–
Off
Prog Sel
8
9
10
11
12
13
14
15
Line Out
EXT-UHD-LANS-RX
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
EXT-UHD-LANS-RX
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver.
3
Reset
Press this button, using the end of a paper clip
or other pointed object, to perform a soft reset.
4
Prog
This button is used for device recovery
operations, in the event of a firmware update
or other failure.
5
Prog Sel
4K Ultra HD
HDMI
over this
IP switch
- Receiver
For normal
operation,
should be in
the Off position. Setting this switch to the On
position,
places
the unitIP
in the
ready-state for
4K Ultra HD
HDMI
over
- Receiver
firmware recovery or debug operations.
14
Introduction
ID
Name
Description
6
CH -/+
Press the - / + buttons button to decrement /
increment, respectively, the current channel
number. See Setting the Video Channel (page
27) for more information.
7
Line Out
Connect a pair of headphones or powerted
speakers to this port.
8
HDMI Out
Use a Gefen CAB-HD-LCK-xxMM Locking
HDMI cable to the connect a display to the
HDMI Out port on the rear panel of the
Receiver unit.
9
RS-232
Using the included 3.5mm-to-Male-DB-9
adapator, connect a DB-9 cable from the
Receiver to the display or another device
to be controlled. See RS-232 Control (page
43) for more information.
10
IR In/Ext
Connect an IR Extender (Gefen part no.
EXT-RMT-EXTIRN) to this port. Alternatively,
connect a 3.5mm mini-stereo connector
from this port to the electrical IR output of
an automation control system.
11
IR Out
Connect an IR Emitter (Gefen part no. EXTIREMIT) from this port to the IR sensor of the
device to be controlled.
12
Opt Out
Connect a digital audio cable with a TOSLINK®
connectors from this port to the digital audio
input of an AV receiver or amplifier.
15
Introduction
ID
Name
Description
13
LAN 1
Use this port to connect IP-enabled devices,
or to daisy-chain additional Receiver units
(only when a single source is used, otherwise
bandwidth may be compromised). CAT-5e or
better cables up to 330 feet/100 meters. This
port is NOT PoE -capable.
14
LAN 2 (PoE)
Connect a CAT-5e or better cable up to 330
feet/100 meters, from this port to a PoEcapable network switch. If a PoE switch is
not available or the Sender and Receiver are
connected directly, then the included 5V
DC power supply must be connected to the
Receiver unit.
15
5V DC
This power receptacle can be used to connect
the included 5V DC power supply. An external
power supply is not required when connecting
to a PoE-enabled switch using the LAN 2 (PoE)
port.
16
Installation
The Gen 2.0 AV and KVM over IP Sender and Receiver units can be connected directly or
EXT-UHD-LANS-TX
through a Local Area Network (LAN). Both installations will be covered.
Local Area Network (LAN) Connection
When connecting the Sender and Receiver units to a Local Area Network (LAN), DHCP, static,
or APIPA (Automatic Private IP Addressing) IP modes can be used. DHCP mode will use the
DHCP server to automatically assign an IP address for each Sender and Receiver unit that
is connected to the network. Static IP mode will allow the IP address for each Sender and
Receiver unit to be configured manually. Contact your network administrator if necessary.
APIAP mode assigns a class-B IP address, in the 169.254.x.x range, to the Sender and
Receiver units, if a DHCP server is not available.
1.
On
Off
Connect aPower
CAT-5e
(orReset
better)
cable
between
the LAN (PoE) port on the Sender unit and a
Link
Mode
Prog
Prog Sel
Gigabit PoE-enabled IP switch.
2.
Connect LAN 2 (PoE) on the Receiver unit to the same network switch. Each cable run can
be up to 330 feet (100 meters).
Sender unit
EXT-UHD-LANS-TX
5V DC
LAN (PoE)
RS-232
IR In/Ext
IR Out
HDMI In
Line In
to PoE-compatible switch
3.
If NOT USING A PoE-compliant switch, then connect the included 5V DC power supplies
to the Sender and Receiver units.
Important
If the IP switch is PoE-compliant and the Sender and Receiver are connected
through their PoE ports, external power supplies will not be required. However,
additional Receivers or other devices connected to the LAN 1 port of a Receiver will
require an external power supply.
4K Ultra HD HDMI over IP - Sender
17
Installation
EXT-UHD-LANS-RX
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
Receiver unit
Connect to LAN
4.
Launch the Gefen Syner-G™ app to discover the IP address of the Sender/Receiver unit.
See the Gefen Syner-G™ User Manual for more information.
5.
Click the desired unit from the list. The currently selected unit will be highlighted in red.
6.
Use the fields in the Device Settings section to change the IP settings, as necessary.
4K Ultra HD HDMI over IP - Receiver
Device Settings
Selected Unit
18
Installation
7.
Once all IP settings have been adjusted, click the Apply button.
8.
Click the Reboot button to apply changes.
9.
Repeat steps 4 - 7 for each Sender and Receiver unit as necessary.
Note
The IP address of both the Sender and Receiver unit can be viewed by disconnecting
the source device. Remove the HDMI cable between the Sender unit and the source
device. The IP address of the Sender and Receiver will be displayed as shown:
Local IP = Receiver unit
FW: V1.53H-Oct-24 779c
Local IP: 169.254.7.231
Remote IP: 169.254.6.250
ID: 001C9103C003
Waiting for video source - standby
Remote IP = Sender unit
10. Open your Web browser and enter the IP address of the desired Sender or Receiver unit
in the address bar.
19
Installation
11.
The Login screen will be displayed.
12. In order to change network settings, you must login as “Administrator”. Select the
“Administrator” username from the drop-down list.
13.
Type the password in the Password field. The default password for “Administrator”
is admin. The password is case-sensitive and will be masked as it is entered.
Note
Passwords and operating features can be changed when logged in as Administrator.
The User option has limited access. To change password credentials, see Changing
the Password (page 60) for more information.
14. Click the Login button.
15.
The Network will automatically be selected. The current IP Mode will be highlighted
within the IP Setup window group.
20
Installation
16. Click the desired IP Mode button.
•
If Static mode is selected, then enter the IP Address, Subnet Mask, and Default Gateway.
Contact your system administrator if necessary.
•
If DHCP mode is selected, then the IP address, subnet mask, and default gateway will be
specified by the DHCP server.
17.
Click the Apply button to save the changes. This operation will require a reboot.
18. Click the Reboot button near the bottom of the page.
19. Repeat steps 12 - 21 for each Sender and Receiver to be configured.
20. After the desired IP settings have been applied, set the video channel for each Sender
unit. See Setting the Video Channel (page 27) for more information.
Important
The use of a Managed Gigabit switch with “Jumbo Frame” and “IGMP Snooping”
capability is required when connecting the Gefen AV over IP products to a network.
The switch should be set to greater than 8K and IGMP Snooping must be enabled.
21
Installation
Using a Direct Connection
EXT-UHD-LANS-TX
By default, all Senders and Receivers are shipped in APIPA (Auto) mode. This network
mode is used for directly connecting Sender and Receiver units to one another. In APIPA
mode, each Sender and Receiver unit assigns itself a unique IP address within the range of
169.254.x.x. Using a direct connection each unit can remain in Auto mode of can be
assigned a static of DHCP IP address using the Gefen Syner-G sofrware or manually through
the built-in web interface.
EXT-UHD-LANS-RX
1.
Connect an HDMI cable to connect the source to the HDMI In port on the Sender unit.
2.
Connect an HDMI cable from the display to the HDMI Out port on the Receiver unit.
3.
On
Off
Connect a Power
CAT-5e
(or Reset
better)
cableProgfrom
the
LAN (PoE) port on the Sender unit to the
Link
Mode
Prog Sel
LAN 1 or LAN 2 (PoE) port on the Receiver unit. The other LAN port can then be used for
connecting (daisy-chaining) an additional Receiver unit. Each cable run can be up to 330
feet (100 meters). Please note that PoE is not active in direct connection. The Sender and
all connected Receivers will need to be powered using their external power supplies.
–
On
Power
5V DC
Link
Reset
LAN (PoE)
Prog
CH
+
Off
EXT-UHD-LANS-TX
Prog Sel
RS-232
IR In/Ext
IR Out
HDMI In
Line In
Sender unit
EXT-UHD-LANS-RX
Line Out
Receiver unit
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
to IP-enabled devices
4.
Connect the included 5V DC locking power supplies to both the Sender unit and Receiver
unit. Do not overtighten the locking connectors. Plug the power supplies to available
electrical outlets.
5.
Obtain the IP address of both the Sender and Receiver unit by disconnecting the video
cable from the Sender unit (or from the source device). Information, similar to the illustration on the next page, will be displayed.
4K Ultra HD HDMI over IP - Sender
22
Installation
Local IP = Receiver unit
Waiting for video source - standby
FW: V1.53H-Oct-24 779c
Local IP: 169.254.7.231
Remote IP: 169.254.6.250
ID: 001C9103C003
Remote IP = Sender unit
6.
Make note of both IP addresses. These IP addresses can be entered in a Web browser to
access the built-in Web interface.
7.
See Local Area Network (LAN) Connection (page 17) and follow steps 4 - 20,
in order to access the built-in Web interface.
8.
Set the video channel. By default, both the Sender and Receiver unit are set
to channel 0. See Setting the Video Channel (page 27) for more information.
9.
Once both Sender and Receiver units are configured using the built-in Web
interface, the shielded CAT-5e cable, between the PC and the Receiver unit,
can be disconnected.
10. See Supplementary Connections (page 24) for instructions on connecting IR, RS-232,
and audio cables.
23
Installation
Supplementary Connections
►► IR
1.
Connect an IR Emitter (Gefen part no. EXT-IREMIT) to the Sender unit and attach
it to the IR sensor on the device to be controlled.
2.
Connect an IR Extender (Gefen part no. EXT-RMT-EXTIRN) to the Receiver unit if the IR
sensor will not be within line-of-site for proper IR control.
►► Audio
See Audio Connections (page 46) for more information on using audio devices.
3.
Connect a 3.5mm mini-stereo cable from the Line In port on the Sender unit to an audio
source.
4.
Connect a pair of powered speakers (or another audio output device) to the Line Out port
on the Receiver unit.
►► RS-232
5.
Connect an RS-232 cable from the PC or automation system to the RS-232 port on the
Sender unit.
6.
Connect an RS-232 cable from the Receiver unit to the RS-232 device to be controlled.
24
Installation
Sample Wiring Diagram
CAT-5 CABLE
VIDEO CABLE
RS-232 CABLE
3.5MM AUDIO CABLE
DIGITAL AUDIO (TOSLINK)
IR IN
IR OUT
Automation
Control Device
Analog Audio Source
with L/R output
To
PoE
IP Switch
EXT-UHD-LANS-TX
5V DC
LAN (PoE)
RS-232
IR In/Ext
IR Out
HDMI In
Line In
EXT-UHD-LANS
Sender
RS-232
Controlled Device
4K Source
with HDMI output
IR Extender
for remote display control
IR Extender
for sourcce control
IR Emitter
to source
To
PoE
IP Switch
EXT-UHD-LANS-RX
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
EXT-UHD-LANS
Receiver
Powered Speakers
or Audio Amplifier
w/analog L/R input
IR Emitter
to remote display control
Audio Amplifier
w/ optical digital input
Display
EXT-UHD-LANS
Note
The wiring diagrams above show an additional IR Emitter (Gefen part no. EXTIREMIT), an additional IR Extender Module (Gefen part no. EXT-RMT-EXTIRN),
and various interconnect cables that are not included with the products. The
Emitter, Extender Module, and select cables are available for purchase from your
Gefen dealer or distributor.
25
LED Status
The Power and Link LED indicators on the Sender and Receiver unit provide basic information
on their current status.
The information, in the tables below, applies to both the Sender and Receiver unit.
Link
Status
Description
Off
•
Connection is not established.
•
Check the cable between the Sender and Receiver
unit.
On
•
Connection is established and video is streaming.
Blinking
•
System is in a state of transition. Connection is
established but streaming has not started.
•
No video source detected.
•
Check that the Receiver unit is connected to the
host.
Power
Status
Description
Off
•
No power.
On
•
Power is on and the system is ready.
Blinking
•
System is booting (not ready).
26
Setting the Video Channel
In order for a Sender and Receiver unit to communicate with one another, they must both
be set to the same video channel. This is similar to changing the channel on a set-top box in
order to view a different program. Pressing and releasing either the CH + or CH - buttons on
the front of the Receiver unit can also be used to change the video channel.
Both methods will be covered in this section. By default, all Sender and Receiver units are set to
channel 0 (zero).
Setting the Channel using the Web Interface
1.
Access the Web interface by entering the IP address of the desired Sender or Receiver
unit.
2.
Login as “Administrator” or “User”.
3.
Click the Functions tab. The current channel is displayed within the Channel Setup
window group.
4.
Type the desired channel number. Channel numbers can range from 0 to 39900.
5.
Click the Apply button on the right-hand side of Channel Setup window group.
6.
The following message will be displayed, at the top of the page, indicating that the
selected channel has been applied.
If the entered value is invalid, then the following message will be displayed:
7.
Access the Web interface of the next unit (Sender or Receiver) by entering its
IP address.
8.
Repeat steps 1 - 5 for each Sender and Receiver to be changed.
27
EXT-UHD-LANS-RX
Setting the Video Channel
Setting the Channel using the Front Panel
1.
Press the CH - or CH + button to display the current channel number. Channel numbers
range from 0 to 39900.
–
On
Power
Link
Reset
Prog
CH
+
Off
Prog Sel
Receiver unit
2.
The current video channel of the Receiver unit will be shown on the connected display.
Channel: 02
EXT-UHD-LANS-RX
Line Out
3.
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
While the current video channel is being displayed, press and release the Switch button
on the Receiver unit. The Receiver unit will change to the next available video channel
that is being used by a Sender unit.
4K Ultra HD HDMI over IP - Receiver
28
Setting the Video Channel
3.
Once the current channel is displayed, do one of the following:
•
Press the CH - button to decrement the current channel number.
•
Press the CH + button to increment the current channel number.
To set the video channel on a Sender unit, use the Web interface. See Setting the Channel
using the Web Interface (page 27) for more information.
The illustration below shows one Receiver unit and three Sender units. The numbers
indicate the video channel for each unit. Here, the Receiver unit is currently set to
channel 2 and is receiving the signal from the Sender unit, set to channel 2.
Receiver unit
Out
LAN
2
Sender unit
2
Sender unit
1
In
Sender unit
5
In
In
To switch the channel, and view the source that is connected to the Sender on channel 5,
press and release the CH + button to increment the video channel until the display shows
the number 5.
Channel: 05
29
Setting the Video Channel
5.
The Receiver unit, on channel 5, is now receiving the signal from the Sender unit on
channel 5.
Receiver unit
Out
LAN
5
Sender unit
2
Sender unit
1
In
Sender unit
5
In
In
30
Blocking & Masking Video
Use the Block Video option on a Sender unit to prevent video from being transmitted to each
of the connected Receiver units (multicast mode only). Use the Mask Video option to selectively
block video on the desired Receiver units.
►► Mask Video
1.
Access the Web interface of a Receiver unit by entering the IP address in the address bar
of the browser.
2.
Login as “Administrator”.
3.
Click the Functions tab.
4.
Under the Video over IP window group, check the Mask Enable box to mask the video.
Deselect this check box to unmask (enable) video.
5.
Click the Apply button within the Video over IP group.
6.
Repeat steps 1 through 5 for each Receiver unit in the system.
31
Blocking & Masking Video
►► Block Video
Note
The Block Enable option is only applicable in multicast mode.
1.
Access the Web interface of a Sender unit by entering the IP address in the address bar of
the browser.
2.
Login as “Administrator”.
3.
Click the Functions tab.
4.
Under the Video over IP window group, check the Block Enable box to block the video.
Deselect this check box to unblock (enable) video.
5.
Click the Apply button within the Video over IP group.
6.
Repeat steps 1 through 5 for each Sender unit in the system.
32
Unicast & Multicast Modes
Configuring Unicast Mode
The term unicast is used to describe a configuration where information is sent from one point
to another point. It is possible to have multiple Sender and Receiver units connected in a
system. However, in unicast mode a Sender unit can communicate with only one Receiver unit
at a time. In unicast mode, the Gefen AV over IP products function similar to a KVM switcher.
Note
The Gefen AV over IP Sender and Receiver units are shipped from the factory in
unicast mode.
The illustration, below, shows 3 Sender units (S1, S2, and S3) and 2 Receiver units
(R1 and R2) on a network, operating in unicast mode. The video channels are notated
in blue.
Figure 2.1 - Unicast mode: A Sender unit can communicate with only one Receiver unit at a time.
Receiver unit
Out
2
LAN
R
2
Sender unit
Receiver unit
1
S
2
R
3
Out
1
Sender unit
In
S
2
1
Sender unit
S
In
1
5
In
1.
Access the Web interface for each Sender and Receiver unit that will be using unicast
mode. In this example, we will start with Receiver unit R1.
2.
Login as “Administrator”.
Tip
In unicast mode, the Gefen AV over IP Senders and Receivers function as a KVM
switcher.
33
Unicast & Multicast Modes
3.
Click the Network tab.
4.
Click the Unicast button under the Network Mode window group. When selected,
the Unicast button will be highlighted in red.
5.
Click the Apply button in the lower-right corner of the Network Mode group.
6.
The following message will be displayed, at the top of the page, indicating that the
casting mode has been applied to the Sender or Receiver unit.
7.
Click the Reboot button at the bottom of the page. If the Reboot button is not clicked,
the following message will be displayed, indicating that the unit must be rebooted.
8.
Repeat steps 1 - 7 in order to configure the Sender unit for unicast mode.
Important
When switching between unicast and multicast modes, both Sender and Receiver
units must be set to the same mode.
34
Unicast & Multicast Modes
Switching between Sender units in Unicast mode
When multiple Sender and Receiver unit are used in unicast mode, the Gefen AV over IP Sender
and Receivers behave as a switcher. In unicast mode, a Sender unit can communicate with only
one Receiver unit at a time.
In the example below, Receiver unit R1 will be switched to receive the source connected to
Sender unit S1. To do this, simply change the video channel.
Figure 2.2 - Unicast mode: Receiver unit R1 is connected to Sender unit S2.
Receiver unit
Out
2
LAN
R
2
Sender unit
Receiver unit
1
S
2
R
3
Out
1
Sender unit
In
S
2
1
Sender unit
S
In
1
5
In
1.
Access the Web interface for Receiver unit R1.
2.
Login as “Administrator”.
3.
Click the Network tab and change the video channel. Refer to Setting the Video
Channel (page 27) if necessary.
4.
Click the Apply button.
5.
The following message will be displayed, at the top of the page, indicating that the
new channel has been applied to the Sender or Receiver unit.
6.
Receiver unit R1 is now receiving the UHD/HD source connected to Sender unit S1,
as shown on the next page.
35
Unicast & Multicast Modes
Figure 2.3 - Unicast mode: Receiver unit R1 is now connected to Sender unit S1.
Receiver unit
Out
2
LAN
R
Sender unit
2
Out
Receiver unit
3
Sender unit
1
5
S
2
R
In
S
2
1
Sender unit
In
S
1
5
In
Now, observe the result when both Sender S1 and S2 are set to channel 5:
Figure 2.4 - Unicast mode violation: Two Sender units (S1 and S2) using the same
video channel.
Receiver unit
Out
2
LAN
R
Sender unit
2
Out
Receiver unit
2
S
3
R
Sender unit
1
5
In
5
2
S
Sender unit
In
S
1
5
In
In this example, Receiver R1 will continue to receive audio/video data from Sender
S1, even though Sender S2 is set to the same channel. The reason for this is
because Receiver R1 and Sender S1 were already set to the same channel and
communicating (as depicted in Figure 2.3). However, this scenario violates the
unicast mode rule: A Sender unit can communicate with only one Receiver unit
at a time.
36
Unicast & Multicast Modes
When using unicast mode, each of the Sender units must be assigned a unique
channel and should never be changed. Use the Receiver unit to switch (channels)
between Sender units.
Note
In unicast mode, if an additional Sender unit is introduced into a system with the
same channel as another Sender unit, then the Receiver unit will continue to receive
audio/video data from the Sender unit which was connected first.
37
Unicast & Multicast Modes
Configuring Multicast Mode
The term multicast is used to describe a configuration where information is sent from one or
more points to a set of other points. For example, a single Sender unit can transmit data to
multiple Receiver units. In addition, if multiple Sender units are used, each Sender unit can
transmit data to any Receiver that is not already receiving data from another Sender unit.
In multicast mode, the Senders and Receivers function similar to a KVM matrix.
The illustration, below, shows 3 Sender units (S1, S2, and S3) and 2 Receiver units
(R1 and R2) on a network, operating in multicast mode. The video channels are shown
in blue.
Figure 2.5 - Multicast mode: A Sender unit can communicate with multiple Receiver units.
Receiver unit
Out
1
LAN
R
2
Sender unit
Receiver unit
1
2
R
S
3
Out
1
Sender unit
In
1
2
S
Sender unit
In
S
1
5
In
1.
Access the Web interface for each Sender and Receiver unit that will be using multicast
mode. In this example, we will start with Receiver S2.
2.
Login as “Administrator”.
Note
In multicast mode, the Gefen AV over IP Senders and Receivers function as a KVM
matrix.
38
Unicast & Multicast Modes
3.
Click the Network tab.
4.
Click the Multicast button under the Network Mode window group. When selected,
the Multicast button will be highlighted in red.
5.
Click the Apply button in the lower-right corner of the Network Mode group.
The following message will be displayed, at the top of the page, indicating that the
casting mode has been applied to the Sender or Receiver unit.
6.
Click the Reboot button at the bottom of the page. If the Reboot button is not clicked,
the following message will be displayed, indicating that the unit must be rebooted.
7.
Repeat the steps above in order to configure the Sender unit to multicast mode.
Important
When switching between unicast and multicast modes, both Sender and Receiver
units must be set to the same mode.
39
Discovery Mode
Gefen Syner-G Discovery
Enabling the Gefen Syner-G Discovery feature allows the Gefen Syner-G Software Suite or
Gefen Discovery Tool App to locate a Sender and/or Receiver on a network. Once the software
is able to locate the unit, IP settings can be changed as desired.
1.
Access the Web interface by entering the IP address of a Receiver or Sender unit.
2.
Login as “Administrator”.
3.
Click the Network tab.
4.
Under the IP Setup window group, check the Gefen Syner-G Discovery box to
allow the Gefen Syner-G software to locate the unit. If you do not want the unit to be
discoverable, then un-check this box.
5.
Click the Apply button.
6.
Click the Reboot button at the bottom of the page to restart the unit and apply
the change.
40
Discovery Mode
Finding Your Device
If several Sender and Receiver unit pairs are connected on a network, you may need to
physically identify a particular Sender and/or Receiver unit. In such a case, use the Find Your
Device feature.
1.
Access the Web interface by entering the IP address of a Receiver or Sender unit.
2.
Login as “Administrator”.
3.
Click the Network tab.
4.
Under the IP Setup window group, click the Show Me button. By default, the Hide Me
button will be selected.
Although shown, below, it is not necessary to have the Gefen Syner-G Discovery
option enabled in order to use the Find Your Device feature.
41
Discovery Mode
EXT-UHD-LANS-RX
5.
The following message will be displayed, at the top of the page, indicating that the
LED indicators on the unit are blinking.
6.
The Power and Link LED indicators will continue to blink until the Hide Me button is
clicked.
–
On
Power
Link
Reset
Prog
CH
+
Off
Prog Sel
Receiver unit (shown)
7.
Click the Hide Me button to stop both LED indicators from blinking.
EXT-UHD-LANS-RX
Line Out
8.
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
The Power and Link LED indicators will stop blinking and the following message will
be displayed at the top of the page.
4K Ultra HD HDMI over IP - Receiver
42
RS-232 Control
The Gefen AV over IP Sender and Receivers support RS-232 pass-through, allowing the control
of remote RS-232 devices. The Sender and Receiver unit which are being used to pass-through
the RS-232 data must be set to the same baud rate as the RS-232 host and client.
In the example below, an RS-232 device has been connected to Receiver R1. We want to control
this product from Sender unit S3, using an automation control device. The channel numbers
are listed in blue.
Figure 2.6 - Basic RS-232 connection
Receiver unit
Out
R
02
2
Sender unit
Receiver unit
1
R
S
12
3
Out
Automation
Control Device
LAN
Sender unit
12
In
2
S
Sender unit
09
S
In
1
RS-232 device
05
In
Table 2.1 - RS-232 settings for an arbitrary RS-232 device.
Description
Setting
Baud rate
19200
Data bits
Parity
Stop bits
Hardware flow control
8
None
1
None
Confirm that the same RS-232 settings are assigned to both the Sender and Receiver units. To
do this, access the Web interface on both the required Sender unit and Receiver unit to set the
proper RS-232 settings. Follow the instructions on the next page.
43
RS-232 Control
1.
Access the Web interface for the Sender unit and login as “Administrator”.
2.
Click the Functions tab.
3.
Locate the Serial over IP group and change the RS-232 settings to match the
settings of the RS-232 device that is being used. In this case, we need to use the settings
from Table 2.1 (see previous page).
4.
Make sure that the Enable Serial over IP box is checked.
5.
Click the Apply button in the lower-right corner of the Serial over IP group.
Important
If Enable Serial over IP is not checked, then RS-232 pass-through will be disabled.
6.
The following message will be displayed, at the top of the page, indicating that the new
Serial over IP options have been applied.
7.
Click the Reboot button at the bottom of the page. If the Reboot button is not clicked,
the following message will be displayed, indicating that the unit must be rebooted.
8.
Repeat steps 1 - 7 for the Receiver unit.
44
RS-232 Control
RS-232 under Unicast Mode
In unicast mode, a Sender unit will be able to communicate with only one Receiver unit
at a time.
Figure 2.7 - In unicast mode, the host can talk to only one RS-232 device at a time.
RS-232 device
Receiver unit
Out
R
02
2
Out
Automation
Control Device
LAN
Sender unit
Receiver unit
S
3
R
1
12
Sender unit
12
S
2
RS-232 device
In
Sender unit
09
In
1
S
05
In
RS-232 under Multicast Mode
In multicast mode, a Sender unit can communicate with multiple Receiver units
simultaneously.
Figure 2.8 - In multicast mode, the host can talk to multiple RS-232 devices.
RS-232 device
Receiver unit
Out
R
12
2
Sender unit
Receiver unit
1
R
12
S
3
Out
Automation
Control Device
LAN
Sender unit
12
S
2
RS-232 device
Sender unit
09
1
S
05
In
45
In
In
EXT-UHD-LANS-TX
Audio Connections
Audio works in both unicast and multicast modes. The only difference between the two
modes is that the Line In port is automatically disabled, on all Receiver units, in multicast
mode. To illustrate how audio works with the Gefen AV over IP Senders and Receivers, we will
set up a microphone and some speakers.
Connect a 3.5mm mini-stereo cable from the Line In port on the Sender unit to the Line
Out port on the computer.
1.
Note
On
Off
Link
Reset
Mode
Prog
Prog Sel
When anPower
audio
cable
is connected
to the
Line In port on the Sender unit, it takes
priority and replaces the audio from the video input. The audio will be heard on the
HDMI Out, Line Out, and Opt Out ports on the Receiver unit.
EXT-UHD-LANS-RX
Connect to Line Out on computer
EXT-UHD-LANS-TX
5V DC
LAN (PoE)
RS-232
IR In/Ext
IR Out
HDMI In
Line In
Sender unit
2.
Connect the Line Out port, on the Receiver unit, to powered speakers or a pair of
headphones.
3.
Connect a Gefen CAB-TLINK-6MM TOSLINK cable from the Opt Out port to the
On
Off
OpticalPower
Digital
Input
of anProg
AV receiverProgorSelamplifier.
Link
Reset
–
CH
+
Connect to powered speakers
of headphones
EXT-UHD-LANS-RX
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
Receiver unit
Connect to optical audio input
on AV receiver / amplifer
4K Ultra HD HDMI over IP - Sender
46
Audio Connections
Figure 2.12 - Audio connections in unicast mode.
Powered speakers
Receiver unit
Video Out
R
Line Out
Video Out
LAN
2
Sender unit
Receiver unit
R
S
07
Sender unit
1
3
02
S
Video In
S
Sender unit
1
07
2
09
Line In
Computer
Video In
05
Audio Sources and De-Embedding
The following outlines the audio de-embedding functionality of this product.
•
If a 3.5mm mini-stereo cable is connected to the Line In port on the Sender unit, then
the HDMI audio will be disabled on the Receiver unit. The Line Out port, on the Receiver
unit, will output audio from the source connected to the Line In port on the Sender unit.
•
When a source is connected to the Line In port on the Sender unit, the audio will be
heard on the HDMI Out, Line Out, and Opt Out ports.
•
The Line In port on the Receiver unit will only pass audio to the Line Out port on the
Sender unit when in unicast mode.
•
The Opt Out port will de-embed both 2-channel PCM and Bitstream (up to 5.1 channel)
audio from the HDMI In port. High-resolution (lossless) audio will not be outputted.
•
HDMI source audio, from the Sender unit, will pass to the HDMI Out and Opt Out ports
on the Receiver unit. HDMI audio will not be converted or down-mixed on the Line Out
port on the Receiver unit.
47
Creating Video Walls
The web interface facilitates the creation of video walls up to 16 horizontal and 16 vertical
displays. Video walls may contain any number or rows and columns and any combination of
these can be enabled, as necesary.
Wall Size and Layout
1.
Access the Web interface for the Receiver unit.
2.
Login as “Administrator” or “User”.
3.
Go to the Functions tab and check the Enable Video Wall option. Click the Apply
button, then refresh the page in the browser. The Video Wall tab will be displayed.
4.
Under Bezel and Gap Compensation, specifiy the Outside Width (OW), Outside Height
(OH), Video Width (VW), and Video Height (VH) fields.
48
Creating Video Walls
5.
Under the Wall Size and Position Layout window group, click the drop-down lists for the
Vertical Monitor Count and Horizontal Monitor Count and select the number of rows
and columns of displays, respectively.
6.
Select the row and column positions using the Row Position and Column Position dropdown lists. Both row and column positions begin with a reference value of zero.
7.
Click the drop-down list, next to the Apply button, to select the desired host or client to
which these settings will be applied.
If the All option is selected, then all parameters will be transferred to all Receiver units.
For monitor count and bezel compensation in a video wall array of matching displays,
this is fine, but the row and position will also be copied. There is an option for “This” unit
that will apply to the current unit being interfaced with. The “This” option can be used
to precisely set the proper position of each unit but would require the user to access
the web interface of each unit to set. Alternatively, the drop-down will provide a list of
all connected host (Sender units) and clients (Receiver units). This process allows the
configuration of an entire video wall from a single unit.
49
Creating Video Walls
Bezel Compensation
Display devices have a region where video data is not displayed. This area is called the bezel.
Bezel compensation takes this area into account when a single video source is mapped across
multiple displays. It is recommended, when a video wall is set up for the first time, that bezel
compensation values be set to zero. Bezel compensation can be adjusted at any time.
The illustration on the left shows a 2x2 video wall without bezel compensation. Note how the
circle is stretched, slightly, horizontally. On the right, bezel compensation is used to correct
the “distorted” image.
1.
Access the Web interface for the Receiver unit.
2.
Login as “Administrator” or “User”.
3.
Click the Video Wall tab.
4.
Adjust the values under the Bezel and Gap Compensation window group. Refer to the
diagram, to the right of each field, to see the effect of each value. All entered values are
applied to the physical displays in 0.1 millimeter increments.
50
Setting the Video Mode
The video mode can be changed using the Mode button or through the Web interface of the
Sender unit. Consecutively pressing the Mode button on the Sender unit will switch between
Graphic and Video mode.
Using the Web interface
1.
Access the Web interface for the Sender unit.
2.
Login as “Administrator” or “User”.
3.
Click the Network tab.
4.
Click the desired mode within the Picture Quality Mode window group. The default
setting is “Video”.
►► Video Mode
If the video signal is motion video, then click the Video button. This mode will optimize
the frame rate.
►► Graphic Mode
If the video signal is a static image, then click the Graphic button.
5.
The selected mode will be displayed on the screen, as shown below.
Video Mode
6.
Graphic Mode
Rebooting the Sender unit is not required for the changes to take effect.
51
Changing the Password
1.
Access the Web interface for the Sender / Receiver unit.
2.
Login as “Administrator”.
3.
Click the System tab.
4.
Under the Password Change window group, enter the new password for the desired
username. Note that the new password will not be masked when it is entered.
5.
Click the Change button.
52
Utilities
Reset using the Web Interface
All Senders and Receivers can be reset using the web interface or using the buttons on the
front panel. When using the Web interface, the Sender / Receiver units will automatically be
reset to Auto IP mode. When using the front-panel buttons, the Sender / Receiver can be reset
to either Auto IP or Static IP mode.
Note
Once a unit has been reset to Auto IP mode, the connection to the Web interface
will be terminated. To reestablish a connection to the Web interface, from your
computer, see Installation (page 17).
1.
Access the Web interface for the desired Sender / Receiver unit. It does not matter which
unit is reset first.
2.
Login as “Administrator”.
3.
Click the System tab.
4.
Click the Utilities rollout.
5.
Click the Factory Default button.
53
Utilities
5.
Both the Power and Link LED indicators will begin to flash.
–
On
Power
Link
Reset
Prog
CH
+
Off
Prog Sel
Receiver unit (shown)
6.
After both LED indicators stop flashing, the unit will be reset.
7.
Repeat the process for each unit.
EXT-UHD-LANS-RX
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
4K Ultra HD HDMI over IP - Receiver
54
Utilities
Reboot using the Web Interface
The Sender and Receiver units can be rebooted in three different ways: Using the Web
interface, the Reset button on the front panel, or simply disconnecting and reconnecting the
power.
1.
Access the Web interface for the Sender / Receiver unit.
2.
Login as “Administrator”.
3.
Click the System tab.
4.
Click the Utilities rollout.
5.
Click the Reboot button.
6.
After a few moments, the Power LED indicator will flash.
7.
Several seconds later, the Power LED indicator will glow solid blue and the Link LED
indicator will begin to flash.
8.
After both LED indicators stop flashing, the reboot process will be complete.
55
Utilities
Reboot using the Front Panel
1.
Press the Reset button, on the desired Sender or Receiver unit, using the end
of a paper clip or other sharp pointed object.
EXT-UHD-LANS-TX
2.
After a few moments, the Power LED indicator will flash.
3.
Several seconds later, the Power LED indicator will glow solid blue and the Link LED
indicator will begin to flash.
4.
After both LED indicators stop flashing, the reboot process will be complete.
Reset button
EXT-UHD-LANS-RX
On
Power
Link
Reset
Mode
Prog
Off
Prog Sel
Sender unit
Reset button
–
On
5V DC Link
Power
LAN (PoE)
Reset
RS-232
Prog
CH
EXT-UHD-LANS-TX
+
Off
IRProg
In/Ext
Sel
IR Out
HDMI In
Line In
Receiver unit
EXT-UHD-LANS-RX
Line Out
HDMI Out
RS-232
IR In/Ext
IR Out
Opt Out
LAN 1
LAN 2 (PoE)
5V DC
56 HD HDMI over IP - Sender
4K Ultra
Telnet Access
Note
By default, the Telnet login credentials are disabled. This setting is required when
using the Matrix controller (Gefen part no. EXT-CU-LAN) but can be enabled for
security purposes. Use the #use_telnet_login command to enable or
disable this feature.
1.
Launch the desired terminal application (e.g. Windows Hyperterminal, etc).
2.
Within the terminal program, enter the IP address of the Sender or Receiver unit that you
wish to control.
3.
Enter the TCP listening port. The default listening port is 23.
4.
After the correct settings have been used in the terminal program, information similar to
the following will be displayed.
In the example, below, we are connected to the client (Receiver unit) and Telnet login has
been enabled:
------------- Welcome to the Gefen Telnet Server ----------ast2-client001C9103C8B3 login:
5.
Login as “Administrator”. The default password is “admin”. To change the Telnet password, see the #set_telnet_pass command.
6.
Type #help for a list of commands or refer to the tables on the following pages.
57
Commands
Important
Commands that are limited to a Sender or Receiver unit are marked as “Tx only”
and “Rx only”, respectively. Unless otherwise noted, commands can be used when
connected to either a Sender or Receiver unit.
Discovery Service
Command
Description
#get_device_desc
Displays the device description
#get_discovery
Displays the current state of the discovery service
#get_discovery_mode
Displays the discovery read/write mode
#get_showme
Displays the status of the showme state
#set_device_desc
Sets the device description
#set_discovery
Enables or disables the discovery service
#set_discovery_mode
Sets the discovery mode
#set_showme
Enables or disables the “show me” feature
Help
Command
Description
#help
Displays a list of available commands
Network
Command
Description
#get_gateway
Displays the gateway IP address
#get_ip_address
Displays the IP address
#get_ip_mode
Displays the IP mode
#get_ipconfig
Displays the IP configuration information
#get_net_mode
Displays the network casting mode
#get_netmask
Displays the subnet mask address
#get_remote_udp_access
Displays the remote UDP access state
#get_remote_udp_ip
Displays the remote UDP IP address
#get_remote_udp_port
Displays the remote UDP listening port
#get_telnet_access
Displays the Telnet access state
58
Commands
Command
Description
#get_telnet_login
Displays the status of the Telnet login
#get_telnet_port
Displays the Telnet listening port
#get_telnet_welcome
Displays the Telnet welcome message
#get_udp_access
Displays the UDP access state
#get_udp_port
Displays the UDP listening port
#get_web_port
Displays the HTTP listening port
#set_gateway
Sets the gateway address
#set_ip_address
Sets the IP address
#set_ip_mode
Sets the IP mode
#set_net_mode
Sets the network casting mode
#set_netmask
Sets the subnet mask address
#set_remote_udp_access
Enables or disables remote UDP access
#set_remote_udp_ip
Sets the remote UDP IP address
#set_remote_udp_port
Sets the remote UDP listening port
#set_telnet_access
Enables or disables Telnet access
#set_telnet_login
Enables or disables the Telnet login
#set_telnet_pass
Sets the Telnet password
#set_telnet_port
Sets the Telnet listening port
#set_telnet_welcome
Sets the Telnet welcome message
#set_udp_access
Enables or disables UDP access
#set_udp_port
Sets the UDP listening port
#set_web_port
Sets the HTTP listening port
Routing
Command
Description
#get_rx_channel
Displays the channel of the Receiver unit (Rx only)
#get_v
Displays the current video input status
r
Routes an input to a Receiver unit (Rx only)
59
Commands
RX Specific
Command
Description
#get_clk_lock
Displays the audio clock lock
#get_edid_copy
Displays the EDID copy state (Rx only)
#get_mask
Displays the current video mask state
#get_rx_id
Displays the ID of the Receiver unit
#get_vw
Displays the status of the video wall
#get_vw_bc
Displays the video wall bezel compensation
#get_vw_delay
Displays the video wall display delay
#get_vw_hscale
Displays the video wall horizontal up-scaling
#get_vw_layout
Displays the video wall horizontal and vertical
maximum display count
#get_vw_osd
Displays the status of the video wall OSD
#get_vw_pos
Displays the video wall display position
#get_vw_shift
Displays the video wall display shift
#get_vw_vscale
Displays the video wall vertical up-scaling
#set_clk_lock
Sets the audio clock lock
#set_edid_copy
Enables or disables EDID copy
#set_mask
Enables or disables video masking
#set_rx_id
Sets the ID of the Receiver unit
#set_vw
Enable / disable video wall
#set_vw_bc
Sets the video wall bezel compensation
#set_vw_delay
Sets the video wall display delay
#set_vw_hscale
Displays the video wall horizontal up-scaling
#set_vw_layout
Sets the video wall horizontal and vertical maximum
display count
#set_vw_osd
Enable / disable the video wall OSD
#set_vw_pos
Sets the video wall display position
#set_vw_shift
Sets the video wall display shift
#set_vw_vscale
Displays the video wall vertical up-scaling
60
Commands
Serial
Command
Description
#get_serial_allow
Displays the Serial-over-IP state
#get_serial_baud
Displays the serial baud rate setting
#get_serial_bits
Displays the serial data bits setting
#get_serial_parity
Displays the serial parity setting
#get_serial_stop
Displays the serial stop bits setting
#set_serial_allow
Enables or disables Serial-over-IP mode
#set_serial_baud
Sets the baud rate for the serial port
#set_serial_bits
Sets the data bits for the serial port
#set_serial_parity
Sets the parity setting for the serial port
#set_serial_stop
Sets the number of stop bits for the serial port
System
Command
Description
#get_firmware_version
Displays the firmware version
#factory_reset
Resets the unit to factory-default settings
#fw_upgrade
Upgrades firmware using external file
#reboot
Reboots the unit
TX Specific
Command
Description
#get_block
Displays the current video blocking state
#get_hdcp
Displays the HDCP state
#get_pq_mode
Displays the picture quality mode
#get_tx_channel
Displays the video channel
#set_block
Enables or disables video blocking
#set_hdcp_allow
Enables or disables HDCP-detection
#set_pq_mode
Sets the picture quality mode
#set_tx_channel
Sets the video channel
61
Commands
Video
Command
Description
#get_video_allow
Displays the Video-over-IP state
#set_video_allow
Sets the Video-over-IP state
Web Interface
Command
Description
#set_webui_ad_pass
Sets the administrator password for the web UI
#set_webui_user_pass
Sets the user password for the web UI
62
Commands
#help
Displays a list of available commands. The commands listed are specific to either the Sender
or Receiver unit.
Syntax
#help
Parameters
None
Example
#help
#HELP
#FACTORY_RESET
#FW_UPGRADE
#GET_BLOCK
#GET_CLK_LOCK
#GET_DEVICE_DESC
#GET_DISCOVERY
#GET_DISCOVERY_MODE
#GET_EDID_COPY
#GET_FIRMWARE_VERSION
#GET_GATEWAY
#GET_HDCP
#GET_IP_ADDRESS
#GET_IP_MODE
#GET_IPCONFIG
#GET_MASK
#GET_NET_MODE
#GET_NETMASK
#GET_PQ_MODE
#GET_REMOTE_UDP_ACCESS
#GET_REMOTE_UDP_IP
#GET_REMOTE_UDP_PORT
#GET_RX_CHANNEL
...
...
63
Commands
#factory_reset
Resets the unit to factory-default settings. param1 must be included and set to 1.
Syntax
#factory_reset param1
Parameters
param1
Integer1
Example
#factory_reset 1
RESET TO FACTORY DEFAULTS
Related Commands
#reboot
64
Commands
#fw_upgrade
Upgrades the firmware from the command.
Syntax
#fw_upgrade filename
Parameters
filename String
Example
#fw_upgrade firmware_file_v2.bin
65
Commands
#get_block
Displays the current video blocking state. This command is only available when connected
to a Sender unit. To enable or disable the video blocking state, refer to the #set_block
command.
Syntax
#get_block
Parameters
None
Example
#get_block
BLOCK DISABLED
Related Commands
#get_mask
#set_block
66
Commands
#get_clk_lock
Displays the audio clock lock.
Syntax
#get_clk_lock
Parameters
None
Example
#get_clk_lock
CLK_LOCK 0
Related Commands
#set_clk_lock
67
Commands
#get_device_desc
Displays the description of the Sender / Receiver unit.
Syntax
#get_device_desc
Parameters
None
Example
#get_device_desc
DEVICE DESCRIPTION IS Genius Sender 2
Related Commands
#set_device_desc
68
Commands
#get_discovery
Displays the current discovery mode setting.
Syntax
#get_discovery
Parameters
None
Example
#get_discovery
DISCOVERY SERVICE SET TO ENABLED
Related Commands
#set_discovery
#set_showme
69
Commands
#get_discovery_mode
Displays the current discovery mode setting.
Syntax
#get_discovery_mode
Parameters
None
Example
#get_discovery_mode
DISCOVERY MODE 1
Related Commands
#set_discovery
#set_discovery_mode
#set_showme
70
Commands
#get_edid_copy
Displays the EDID copy state. This command is only available when connected
to a Receiver unit.
Syntax
#get_edid_copy
Parameters
None
Example
#get_edid_copy
COPY EDID OF CONNECTED DISPLAY IS ENABLED
Related Commands
#set_edid_copy
71
Commands
#get_firmware_version
Displays the firmware version.
Syntax
#get_firmware_version
Parameters
None
Example
#get_firmware_version
FIRMWARE VERSION IS 1.83hv
Related Commands
#fw_upgrade
72
Commands
#get_gateway
Displays the gateway address of the Sender/Receiver unit.
Syntax
#get_gateway
Parameters
None
Example
#get_gateway
GATEWAY: 192.168.0.1
Related Commands
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
73
Commands
#get_hdcp
Displays the current HDCP state. This command is only available when connected
to a Sender unit.
Syntax
#get_hdcp
Parameters
None
Example
#get_hdcp
HDCP ENCRYPTED SOURCE IS ENABLE
Related Commands
#set_hdcp_allow
74
Commands
#get_ip_address
Displays the current IP address of the Sender or Receiver unit.
Syntax
#get_ip_address
Parameters
None
Example
#get_ip_address
IP: 10.5.64.60
Related Commands
#get_gateway
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
75
Commands
#get_ip_mode
Displays the current IP mode.
Syntax
#get_ip_mode
Parameters
None
Example
#get_ip_mode
IP MODE IS SET TO DHCP
Related Commands
#get_gateway
#get_ip_address
#get_ipconfig
#get_netmask
#get_web_port
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
76
Commands
#get_ipconfig
Displays the current IP configuration. In addition to providing the MAC address and the
broadcast IP address, this command also provides the same information as executing the
#get_ip_mode, #get_ip_address, #get_netmask, and #get_gateway
commands.
Syntax
#get_ipconfig
Parameters
None
Example
#get_ipconfig
IP CONFIGURATION IS :
IP MODE: DHCP
IP: 10.5.64.60
NETMASK: 255.255.255.0
GATEWAY: 10.5.64.1
MAC ADDRESS: 00-1C-91-03-C8-B3
Related Commands
#get_gateway
#get_ip_address
#get_netmask
#get_web_port
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
77
Commands
#get_mask
Displays the current video mask state. This command is only available when connected
to a Receiver unit. To enable or disable video masking on a Receiver unit, refer to the #set_
mask command.
Syntax
#get_mask
Parameters
None
Example
#get_mask
MASK DISABLED
Related Commands
#get_block
#set_mask
78
Commands
#get_net_mode
Displays the current network mode setting.
Syntax
#get_net_mode
Parameters
None
Example
#get_net_mode
NETWORK MODE SET TO MULTICAST
Related Commands
#set_net_mode
79
Commands
#get_netmask
Displays the current net mask setting.
Syntax
#get_netmask
Parameters
None
Example
#get_netmask
NETMASK: 255.255.255.0
Related Commands
#get_gateway
#get_ip_address
#get_ipconfig
#get_web_port
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
80
Commands
#get_pq_mode
Displays the picture quality mode. This command is only available when connected to a
Sender unit.
Syntax
#get_pq_mode
Parameters
None
Example
#get_pq_mode
TRANSMITTER PICTURE QUALITY IS VIDEO
Related Commands
#set_pq_mode
81
Commands
#get_remote_udp_access
Displays the remote UDP access state.
Syntax
#get_remote_udp_access
Parameters
None
Example
#get_remote_udp_access
REMOTE UDP ACCESS IS ENABLED
Related Commands
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
82
Commands
#get_remote_udp_ip
Displays the remote UDP IP address.
Syntax
#get_remote_udp_ip
Parameters
None
Example
#get_remote_udp_access
REMOTE UDP IP: 192.168.1.29
Related Commands
#get_remote_udp_access
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
83
Commands
#get_remote_udp_port
Displays the remote UDP listening port.
Syntax
#get_remote_udp_port
Parameters
None
Example
#get_remote_udp_port
REMOTE UDP COMMUNICATIONS PORT: 50008
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
84
Commands
#get_rx_channel
Displays the current channel of the Receiver unit. To set the video channel of a Receiver unit,
use the r command.
Syntax
#get_rx_channel
Parameters
None
Example
#get_rx_channel
RECEIVER CHANNEL: 1
Related Commands
#get_tx_channel
#set_tx_channel
r
85
Commands
#get_rx_id
Displays the ID of the Receiver unit. This command is only available when connected
to a Receiver unit.
Syntax
#get_rx_id
Parameters
None
Example
#get_rx_id
RX ID: 8
Related Commands
#set_rx_id
86
Commands
#get_serial_allow
Displays the Serial-over-IP state. Use the #set_serial_allow command to enable
or disable the Serial-over-IP feature.
Syntax
#get_serial_allow
Parameters
None
Example
#get_serial_allow
SERIAL OVER IP is ENABLE
Related Commands
#get_serial_baud
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
87
Commands
#get_serial_baud
Displays the serial baud rate setting. Use the #set_serial_baud command to set
the baud rate.
Syntax
#get_serial_baud
Parameters
None
Example
#get_serial_baud
SERIAL BAUD RATE IS 19200
Related Commands
#get_serial_allow
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
88
Commands
#get_serial_bits
Displays the serial data bits setting. Use the #set_serial_bits command to set
the number of data bits.
Syntax
#get_serial_bits
Parameters
None
Example
#get_serial_bits
SERIAL DATA BITS IS 8
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
89
Commands
#get_serial_parity
Displays the serial parity bit setting. Use the #set_serial_parity command to set
the parity bit.
Syntax
#get_serial_parity
Parameters
None
Example
#get_serial_parity
SERIAL PARITY MODE SET TO NONE
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
90
Commands
#get_serial_stop
Displays the serial stop bits setting. Use the #set_serial_stop command to set
the number of stop bits.
Syntax
#get_serial_stop
Parameters
None
Example
#get_serial_stop
SERIAL STOP BITS IS 1
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
91
Commands
#get_showme
Displays the showme state.
Syntax
#get_showme
Parameters
None
Example
#get_showme
SHOW ME DISABLED
Related Commands
#set_showme
92
Commands
#get_telnet_access
Displays the Telnet access state. Use the #set_telnet_access command to enable
or disable Telnet access.
Syntax
#get_telnet_access
Parameters
None
Example
#get_telnet_access
TELNET ACCESS IS ENABLED
Related Commands
#get_telnet_login
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_pass
#set_telnet_login
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
93
Commands
#get_telnet_login
Displays the Telnet login status.
Syntax
#get_telnet_login
Parameters
None
Example
#get_telnet_login
TELNET LOGIN SET TO DISABLED
Related Commands
#get_telnet_access
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_pass
#set_telnet_login
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
94
Commands
#get_telnet_port
Displays the Telnet listening port.
Syntax
#get_telnet_port
Parameters
None
Example
#get_telnet_port
TELNET COMMUNICATION PORT: 23
Related Commands
#get_telnet_access
#get_telnet_login
#get_telnet_welcome
#set_telnet_access
#set_telnet_pass
#set_telnet_login
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
95
Commands
#get_telnet_welcome
Displays the Telnet welcome message. Use the #set_telnet_welcome to create
a custom welcome message.
Syntax
#get_telnet_welcome
Parameters
None
Example
#get_telnet_welcome
TELNET WELCOME SCREEN IS DISABLED
Related Commands
#get_telnet_access
#get_telnet_login
#get_telnet_port
#set_telnet_access
#set_telnet_pass
#set_telnet_login
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
96
Commands
#get_tx_channel
Displays the video channel of the Sender unit. This command is only available when
connected to a Sender unit.
Syntax
#get_tx_channel
Parameters
None
Example
#get_tx_channel
TRANSMITTER CHANNEL: 1
Related Commands
#get_rx_channel
#set_tx_channel
r
97
Commands
#get_udp_access
Displays the UDP access state. Use the #set_udp_access command to enable
or disable UDP access.
Syntax
#get_udp_access
Parameters
None
Example
#get_udp_access
UDP ACCESS IS ENABLED
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
98
Commands
#get_udp_port
Displays the local UDP listening port.
Syntax
#get_udp_port
Parameters
None
Example
#get_udp_port
UDP PORT SET TO 50007
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
99
Commands
#get_video_allow
Displays the Video-over-IP status. Use the #set_video_allow command to enable
or disable video over IP.
Syntax
#get_video_allow
Parameters
None
Example
#get_video_allow
VIDEO OVER IP is ENABLE
Related Commands
#set_video_allow
100
Commands
#get_vw
Displays the video wall enable/disable setting.
Syntax
#get_vw
Parameters
None
Example
#get_vw
VW 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
101
Commands
#get_vw_bc
Displays the video wall bezel compensation setting.
Syntax
#get_vw_bc
Parameters
None
Example
#get_vw_bc
VW_BC 6223 6550 3429 4010
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
102
Commands
#get_vw_delay
Displays the video wall delay setting.
Syntax
#get_vw_delay
Parameters
None
Example
#get_vw_delay
VW_DELAY 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
103
Commands
#get_vw_hscale
Displays the video wall horizontal upscaling value.
Syntax
#get_vw_bc
Parameters
None
Example
#get_vw_bc
VW_HSCALE 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
104
Commands
#get_vw_layout
Displays the video wall horizontal and vertical display count.
Syntax
#get_vw_layout
Parameters
None
Example
#get_vw_layout
VW_LAYOUT 2 2
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
105
Commands
#get_vw_osd
Displays the enable / disable status of the video wall OSD.
Syntax
#get_vw_osd
Parameters
None
Example
#get_vw_osd
VW_OSD 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
106
Commands
#get_vw_pos
Displays the video wall display position.
Syntax
#get_vw_pos
Parameters
None
Example
#get_vw_pos
VW_POS 0 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
107
Commands
#get_vw_shift
Displays the video wall display shift.
Syntax
#get_vw_shift
Parameters
None
Example
#get_vw_shift
VW_SHIFT 0 0 0 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
108
Commands
#get_vw_vscale
Displays the video wall vertical upscaling value.
Syntax
#get_vw_vscale
Parameters
None
Example
#get_vw_vscale
VW_VSCALE 0
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
109
Commands
#get_web_port
Displays the HTTP listening port. Use the #set_web_port command to set the HTTP
listening port.
Syntax
#get_web_port
Parameters
None
Example
#get_web_port
WEB INTERFACE PORT: 80
Related Commands
#get_gateway
#get_ip_address
#get_ipconfig
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
110
Commands
#reboot
Reboots the Sender / Receiver unit.
Syntax
#reboot
Parameters
None
Example
#reboot
UNIT WILL REBOOT SHORTLY
Related Commands
#factory_reset
111
Commands
#set_block
Enables or disables video blocking at a Sender unit.
Syntax
#set_block param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_block 1
BLOCK ENABLED
Related Commands
#get_block
#set_mask
112
Commands
#set_clk_lock
Sets the audio clock lock. This command is only available on the Receiver unit. After executing
this command, the unit must be rebooted to apply the changes.
Syntax
#set_block param1
Parameters
param1
Integer[0 ... 500]
Example
#set_clk_lock 100
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_clk_lock
113
Commands
#set_device_desc
Sets the description for the Sender / Receiver unit. The description string cannot exceed 30
characters in length. Spaces and underscore characters are acceptable. Avoid using symbols
and special characters.
Syntax
#set_description param1
Parameters
param1
String
Example
#set_description Blu-ray_Panasonic
PRODUCT DESCRIPTION SET
Related Commands
#get_device_desc
114
Commands
#set_discovery
Enables or disables the discovery feature. The default value is On.
Syntax
#set_discovery param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Off
1
On
Example
#set_discovery 0
DISCOVERY SERVICE SET TO DISABLED
Related Commands
#get_discovery
#set_showme
#get_showme
115
Commands
#set_discovery_mode
Sets the discovery read / write mode.
Syntax
#set_discovery_mode param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Read only mode
1
Read / write mode
Example
#set_discovery_mode 1
DISCOVERY MODE 1
Related Commands
#get_edid_copy
116
Commands
#set_edid_copy
Enables or disables the EDID copy state. When param1 = 1, the downstream EDID (connected
to the Receiver unit) is copied to the Sender unit. If param1 = 0, then the internal (default)
EDID is used. This command is only available when connected
to a Receiver unit. After executing this command, the unit must be rebooted to apply the
changes.
Syntax
#set_edid_copy param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Off
1
On
Example
#set_edid_copy 1
COPY EDID OF CONNECTED DISPLAY SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_edid_copy
117
Commands
#set_gateway
Sets the gateway address. This command is only applicable when using Static IP mode.
param1 must be specified using dot-decimal notation. After executing this command, the unit
must be rebooted to apply the changes.
Syntax
#set_gateway param1
Parameters
param1
IP Address
Example
#set_gateway 192.168.1.1
GATEWAY ADDRESS SET TO 192.168.1.1
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_ip_address
#set_ip_mode
#set_netmask
#set_web_port
118
Commands
#set_hdcp_allow
Blocks or unblocks HDCP-encrypted sources. This command does not decrypt HDCP content
and is only available when connected to a Sender unit. After executing this command, the
unit must be rebooted to apply the changes.
Syntax
#set_hdcp_allow param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_hdcp_allow 1
HDCP ENCRYPTED SOURCE SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_hdcp_allow
119
Commands
#set_ip_address
Sets the IP address. param1 must be specified using dot-decimal notation. After executing
this command, the unit must be rebooted to apply the changes.
Syntax
#set_ip_address param1
Parameters
param1
IP Address
Example
#set_gateway 192.168.1.1
GATEWAY ADDRESS SET TO 192.168.1.1
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_gateway
#set_ip_mode
#set_netmask
#set_web_port
120
Commands
#set_ip_mode
Sets the IP mode. After executing this command, the unit must be rebooted to apply the
changes.
Syntax
#set_ip_mode param1
Parameters
param1
Integer[0 ... 2]
param1
Description
0
Static
1
2
DHCP
Auto IP
Example
#set_ip_mode 1
IP MODE SET TO DHCP
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_ip_address
#set_gateway
#set_netmask
#set_web_port
121
Commands
#set_mask
Enables or disables video masking at a Receiver unit.
Syntax
#set_mask param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_mask 1
MASK ENABLED
Related Commands
#get_mask
#set_block
122
Commands
#set_net_mode
Sets the network casting mode.
Syntax
#set_net_mode param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Unicast
1
Multicast
Example
#set_net_mode 0
NETWORK CASTING MODE SET TO UNICAST
Related Commands
#get_net_mode
123
Commands
#set_netmask
Sets the network mask address. param1 must be specified using dot-decimal notation. After
executing this command, the unit must be rebooted to apply the changes.
Syntax
#set_netmask param1
Parameters
param1
IP Address
Example
#set_netmask 255.255.255.0
NETMASK ADDRESS SET TO 255.255.255.0
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_ip_address
#set_ip_mode
#set_gateway
#set_web_port
124
Commands
#set_pq_mode
Sets the picture quality mode. This command is only available when connected
to a Sender unit.
Syntax
#set_pq_mode param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Graphic
1
Video
Example
#set_pq_mode 1
TRANSMITTER PICTURE QUALITY SET TO VIDEO
Related Commands
#get_pq_mode
125
Commands
#set_remote_udp_access
Enables or disables remote UDP access. After executing this command, the unit must be
rebooted to apply the changes.
Syntax
#set_remote_udp_access param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_remote_udp_access 1
REMOTE UDP ACCESS SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
#set_udp_port
126
Commands
#set_remote_udp_ip
Set the remote UDP IP address. param1 must be specified using dot-decimal notation. After
executing this command, the unit must be rebooted to apply the changes.
Syntax
#set_remote_udp_ip param1
Parameters
param1
IP address
Example
#set_remote_udp_ip 192.168.1.29
REMOTE UDP IP ADDRESS SET TO 192.168.1.29
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_port
#set_udp_access
#set_udp_port
127
Commands
#set_remote_udp_port
Set the remote UDP listening port. After executing this command, the unit must be rebooted
to apply the changes.
Syntax
#set_remote_udp_port param1
Parameters
param1
Integer[0 ... 65535]
Example
#set_remote_udp_port 50008
REMOTE UDP COMMUNICATIONS PORT IS SET TO PORT 50008
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_udp_access
#set_udp_port
128
Commands
#set_rx_id
Sets the ID of the Receiver unit. This command is only available when connected
to a Receiver unit.
Syntax
#set_rx_id param1
Parameters
param1
Integer[0 ... 65535]
Example
#set_rx_id 1
RX ID: 1
Related Commands
#get_rx_id
129
Commands
#set_serial_allow
Enables or disables serial over IP. After executing this command, the unit must be rebooted to
apply the changes.
Syntax
#set_serial_allow param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disable
1
Enable
Example
#set_serial_allow 0
SERIAL OVER IP SET TO DISABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
130
Commands
#set_serial_baud
Sets the baud rate for the serial port. After executing this command, the unit must be
rebooted to apply the changes.
Syntax
#set_serial_baud param1
Parameters
param1
Integer[0 ... 9]
param1
Description (baud rate)
0
300
1
2
3
4
5
6
7
8
Example
9
600
1200
2400
4800
9600
19200
38400
57600
115200
#set_serial_baud 6
SERIAL BAUD RATE SET TO 19200
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_bits
#set_serial_parity
#set_serial_stop
131
Commands
#set_serial_bits
Sets the data bits for the serial port. After executing this command, the unit must be rebooted
to apply the changes.
Syntax
#set_serial_bits param1
Parameters
param1
Integer[0 ... 3]
param1
Description (data bits)
0
5
1
2
3
6
7
8
Example
#set_serial_bits 3
SERIAL DATA BITS SET TO 8
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
#set_serial_stop
132
Commands
#set_serial_parity
Sets the parity bit for the serial port. After executing this command, the unit must be
rebooted to apply the changes.
Syntax
#set_serial_parity param1
Parameters
param1
Integer[0 ... 2]
param1
Description
0
None
1
2
Odd
Even
Example
#set_serial_parity 0
SERIAL PARITY MODE SET TO NONE
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_stop
133
Commands
#set_serial_stop
Sets the number of stop bits for the serial port. After executing this command, the unit must
be rebooted to apply the changes.
Syntax
#set_serial_stop param1
Parameters
param1
Integer[0 ... 1]
param1
Description (stop bits)
0
1
1
2
Example
#set_serial_stop 0
SERIAL STOP BITS SET TO 1
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_serial_allow
#get_serial_baud
#get_serial_bits
#get_serial_parity
#get_serial_stop
#set_serial_allow
#set_serial_baud
#set_serial_bits
#set_serial_parity
134
Commands
#set_showme
Enables or disables the “Show Me” feature. When the “Show Me” feature is enabled,
then both the Power and Link LED indicators, on the front panel, will flash. This quickly
identifies a unit and is useful when multiple units are being used. The default setting is
disabled.
Syntax
#set_showme param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_showme 1
SHOW ME ENABLED
Related Commands
#get_discovery
#set_discovery
135
Commands
#set_telnet_access
Enables or disables Telnet access. After executing this command, the unit must be rebooted
to apply the changes.
Syntax
#set_telnet_access param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_telnet_access 1
TELNET ACCESS SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_telnet_access
#get_telnet_login
#get_telnet_port
#get_telnet_welcome
#set_telnet_login
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
136
Commands
#set_telnet_login
Enables or disables the Telnet login process. After executing this command, the unit must be
rebooted to apply the changes.
Syntax
#set_telnet_login param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_telnet_login 1
TELNET INTERFACE LOGIN SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_telnet_access
#get_telnet_pass
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_pass
#set_telnet_port
#set_telnet_welcome
137
Commands
#set_telnet_pass
Sets the Telnet password. The password cannot exceed 8 characters in length and is casesensitive. No special characters are allowed. The default password is admin. After executing
this command, the unit must be rebooted to apply the changes.
Syntax
#set_telnet_pass param1
Parameters
param1
String
Example
#set_telnet_pass b055man
TELNET INTERFACE PASSWORD IS SET b055man
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_telnet_access
#get_telnet_pass
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_login
#set_telnet_port
#set_telnet_welcome
138
Commands
#set_telnet_port
Sets the Telnet listening port. After executing this command, the unit must be rebooted to
apply the changes.
Syntax
#set_telnet_port param1
Parameters
param1
Integer[0 ... 65535]
Example
#set_telnet_port 23
TELNET COMMUNICATIONS PORT SET TO PORT 23
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_telnet_access
#get_telnet_pass
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_login
#set_telnet_pass
#set_telnet_welcome
139
Commands
#set_telnet_welcome
Enables / disables the Telnet welcome screen. After executing this command, the unit must
be rebooted to apply the changes.
Syntax
#set_telnet_welcome param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_telnet_welcome Welcome!
TELNET WELCOME SCREEN IS ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_telnet_access
#get_telnet_pass
#get_telnet_port
#get_telnet_welcome
#set_telnet_access
#set_telnet_login
#set_telnet_pass
#set_telnet_port
140
Commands
#set_tx_channel
Sets the video channel for the Sender unit. This command is only available when connected to
the Sender unit.
Syntax
#set_tx_channel param1
Parameters
param1
Integer[0 ... 255]
Example
#set_tx_channel 1
TRANSMITTER CHANNEL SET TO 1
Related Commands
#get_tx_channel
#get_rx_channel
r
141
Commands
#set_udp_access
Enables or disables UDP access. After executing this command, the unit must be rebooted to
apply the changes.
Syntax
#set_udp_access param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_udp_access 0
UDP ACCESS SET TO DISABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_port
142
Commands
#set_udp_port
Sets the local UDP listening port. After executing this command, the unit must be rebooted to
apply the changes.
Syntax
#set_udp_port param1
Parameters
param1
Integer[0 ... 65535]
Example
#set_udp_port 50007
UDP COMMUNCATION IS SET TO PORT 50007
PLEASE REBOOT THE UNIT TO APPLY CHANGES.
Related Commands
#get_remote_udp_access
#get_remote_udp_ip
#get_remote_udp_port
#get_udp_access
#get_udp_port
#set_remote_udp_access
#set_remote_udp_ip
#set_remote_udp_port
#set_udp_access
143
Commands
#set_video_allow
Enables or disables the Video-over-IP feature. After executing this command, the unit must
be rebooted to apply the changes.
Syntax
#set_video_allow param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disabled
1
Enabled
Example
#set_video_allow 1
VIDEO OVER IP IS SET TO ENABLED
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_video_allow
144
Commands
#set_vw
Enable / disable the video wall. After executing this command, the unit must be rebooted to
apply the changes.
Syntax
#set_vw param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disable
1
Enable
Example
#set_vw 1
VW 1
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
145
Commands
#set_vw_bc
Sets the video wall bezel compensation value. All arguments are expressed in 0.1 mm units:
param1 is the video width
param2 is the overall width
param3 is the video height
param4 is the overall height
Syntax
#set_vw_bc param1 param2 param3 param4
Parameters
param1
param2
param3
param4
Integer[0 ... 99999]
Integer[0 ... 99999]
Integer[0 ... 99999]
Integer[0 ... 99999]
Example
#set_vw_bc 190 200 90 100
VW_BC 190 200 90 100
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
146
Commands
#set_vw_delay
Sets the video wall display delay in microseconds.
Syntax
#set_vw_delay param1
Parameters
param1
Integer[0 ... 99999]
Example
#set_vw_delay 16000
VW_DELAY 16000
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw_bc
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
147
Commands
#set_vw_hscale
Sets the video wall horizontal upscaling.
Syntax
#set_vw_hscale param1
Parameters
param1
Integer[0 ... 1]
Example
#set_vw_hscale 1
VW_HSCALE 1
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_delay
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
148
Commands
#set_vw_layout
Sets the maximum horizontal and vertical display count for the video wall:
param1 is the maximum horizontal display count.
param2 is the maximum vertical display count.
Syntax
#set_vw_layout param1 param2
Parameters
param1
param2
Integer[0 ... 15]
Integer[0 ... 15]
Example
#set_vw_layout 2 2
VW_LAYOUT 2 2
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_osd
#set_vw_pos
#set_vw_shift
#set_vw_vscale
149
Commands
#set_vw_osd
Enable / disable the video wall OSD.
Syntax
#set_vw_osd param1
Parameters
param1
Integer[0 ... 1]
param1
Description
0
Disable
1
Enable
Example
#set_vw_osd 1
VW_OSD 1
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_pos
#set_vw_shift
#set_vw_vscale
150
Commands
#set_vw_pos
Sets the video wall position.
param1 is the row position.
param2 is the column position.
Syntax
#set_vw_pos param1 param2
Parameters
param1
param2
Integer[0 ... 15]
Integer[0 ... 15]
Example
#set_vw_pos 2 2
VW_POS 2 2
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_shift
#set_vw_vscale
151
Commands
#set_vw_shift
Sets the video wall display shift. param2 must be specified in increments of eight pixels (e.g.
0, 8, 16, 24, etc.)
Syntax
#set_vw_shift param1 param2
Parameters
param1
Character
param1
Description
U
Shift up
D
L
R
param2
Shift down
Shift left
Shift right
Integer[0 ... 80000]
Example
#set_vw_shift L 16
VW_SHIFT L 16
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_pos
#set_vw_vscale
152
Commands
#set_vw_vscale
Sets the video wall vertical upscaling.
Syntax
#set_vw_vscale param1
Parameters
param1
Integer[0 ... 15]
Example
#set_vw_vscale 1
VW_VSCALE 1
Related Commands
#get_vw_bc
#get_vw_delay
#get_vw_hscale
#get_vw_layout
#get_vw_osd
#get_vw_pos
#get_vw_shift
#get_vw_vscale
#set_vw_bc
#set_vw_delay
#set_vw_hscale
#set_vw_layout
#set_vw_osd
#set_vw_shift
153
Commands
#set_web_port
Sets the HTTP listening port.
Syntax
#set_web_port param1
Parameters
param1
Integer[0 ... 65535]
Example
#set_web_port 82
WEB INTERFACE PORT SET TO 80
PLEASE REBOOT THE UNIT TO APPLY CHANGES
Related Commands
#get_gateway
#get_ip_address
#get_ip_mode
#get_ipconfig
#get_netmask
#get_web_port
#set_gateway
#set_ip_address
#set_ip_mode
#set_netmask
154
Commands
#set_webui_ad_pass
Sets the Administrator password for the Web interface login. The password cannot exceed
eight characters in length. The default password is admin.
Syntax
#set_webui_ad_pass param1
Parameters
param1
Password
Example
#set_webui_ad_pass b05Sman
WEB UI ADMINISTRATOR PASSWORD IS SET
Related Commands
#set_webui_user_pass
155
Commands
#set_webui_user_pass
Sets the User password for the Web interface login. The password cannot exceed eight
characters in length. The default password is user.
Syntax
#set_webui_user_pass param1
Parameters
param1
Password
Example
#set_webui_user_pass m1ni0n
WEB UI USER PASSWORD IS SET
Related Commands
#set_webui_ad_pass
156
Commands
r
Changes a Receiver unit to the specified video channel. Changing the video channel allows a
Receiver unit to accept the signal from a Sender unit that uses the same video channel. This
command is only available when connected to a Receiver unit. Do not precede this command
with the # symbol.
Syntax
r param1
Parameters
param1
Integer[0 ... 255]
Example
r 1
TRANSMITTER 1 ROUTED TO RECEIVER
Related Commands
None
157
Network Cable Diagram
Front of RJ-45 Connector
1 2 3 4 5 6 7 8
Gefen recommends the TIA/EIA-568-B wiring option. Use the table below when
field-terminating cable for use with Gefen products.
Pin
Color
Description
1
Orange / White
TD+ (Transmit Data, positive differential signal)
2
Orange
TD- (Transmit Data, negative differential signal)
3
Green / White
RD+ (Receive Data, positive differential signal)
4
Blue
Unused
5
Blue / White
Unused
6
Green
RD- (Receive Data, negative differential signal)
7
Brown / White
Unused
8
Brown / White
Unused
Note
Shielded CAT-5e (or better) cabling should be used..
158
Rack Tray Installation
The following illustrations provide instructions for installing the Sender and/or Receiver
unit(s) in the Gefen 1U Rack Tray (Gefen part no. EXT-RACK-1U-GRY).
Step 1
Turn unit upside down.
Step 2
Remove rubber feet.
Step 3
Line up holes on unit and rack tray.
Step 4
Install countersink screws .
Step 5
Ensure the unit is installed securely.
Step 6
Unit has been installed into rack tray.
159
Specifications*
Connectors & Indicators
HDMI In Connector (Sender)
•
1 x HDMI Type A 19-pin, locking, female
HDMI Out Connector (Receiver)
•
1 x HDMI Type A 19-pin, locking, female
Line In Connector (Sender)
•
1 x 3.5mm mini-stereo, female
Line Out Connector (Receiver)
•
1 x 3.5mm mini-stereo, female
Opt Out Connector (Receiver)
•
1 x TOSLINK®
LAN Connector (Sender)
•
1 x RJ-45, shielded, with PoE
LAN Connectors (Receiver)
•
2 x RJ-45, shielded, 1 with PoE
RS-232 Connector (Sender)
•
1 x 3.5mm mini-stereo, female
RS-232 Connector (Receiver)
•
1 x 3.5mm mini-stereo, female
IR Extender Type
•
EXT-RMT-EXTIRN
IR In/Ext Connector (Sender / Receiver)
•
1 x 3.5mm mini-stereo, female
IR Out Connector (Sender / Receiver)
•
1 x 3.5mm mini-stereo, female
Power Requirement (Sender / Receiver)
•
5V DC, or PoE (802.3af standard)
Power Connector (Sender / Receiver)
•
1 x 5V DC, locking, 5.5mm barrel/2.1mm pin
Power Indicator (Sender / Receiver)
•
1 x LED, blue
Link Indicator (Sender / Receiver)
•
1 x LED, green
Operating Temperature
•
+32 to +122°F (0 to +50°C)
Operating Humidity
•
5% to 90% RH, non-condensing
Storage Temperature
•
-4 to +185°F (-20 to +85°C)
Storage Humidity
•
0% to 95% RH, non-condensing
MTBF
•
50000 hours
•
Sender: 8.4” x 1.0” x 4.9” (214mm x 25mm x
123mm)
Receiver: 8.4” x 1.0” x 4.9” (214mm x 25mm x
123mm)
Operational
Physical
Dimensions (W x H x D,
not including connectors)
•
* Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
160
Nortek Security & Control, LLC
1800 S McDowell Blvd. Petaluma CA 94954, USA
1-707-283-5900 1-800-472-5555
Copyright© 2018 Nortek Security & Control, LLC
Part Number: MAN-EXT-UHD-LANS
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising