Gefen | EXT-UHDV-WP-HBTLS-TX | Gefen EXT-UHDV-WP-HBTLS-TX Manual | Gefen EXT-UHDV-WP-HBTLS-TX 4K Ultra HD Multi-Format 2x1 HDBaseT Wall-Plate Sender w/ Scaler, Auto-Switching, and POH Manual

Gefen EXT-UHDV-WP-HBTLS-TX 4K Ultra HD Multi-Format 2x1 HDBaseT Wall-Plate Sender w/ Scaler, Auto-Switching, and POH Manual
4K Ultra HD HDBaseT™
Multi-Format 2x1 Auto-Switching Wall-Plate Sender w/ Scaler
Receiver w/ Audio De-Embedder and POH
EXT-UHDV-WP-HBTLS-TX
EXT-UHDA-HBTL-RX
User Manual
Version A1
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install or place this product near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15.
Batteries that may be included with this product and/or accessories should never be
exposed to open flame or excessive heat. Always dispose of used batteries
according to the instructions.
2
Warranty Information
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Connect section of the Gefen website at http://www.gefen.com/connect/warranty-andreturn-policy
3
Contact Us
Technical Support
1-707-283-5900
1-800-472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacific Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Nortek Security & Control, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
© 2018 Noretk Security & Control, LLC. All Rights Reserved.
All trademarks are the property of their respective owners.
Gefen and Nortek Security & Control, LLC reserve the right to make changes in the hardware,
packaging, and any accompanying documentation without prior notice.
4
Operating Notes
Important
•
While Unshielded (UTP) CAT-5e is usually adequate, shielded (STP) CAT-6A is recommended. Shielded (STP) CAT-5e or unshielded (UTP) CAT-5e or CAT6A may be acceptable depending on cable quality. Care should always be given
to keep these cables away from power lines and other sources of electromagnetic
interference.
•
Cable quality is critical when handling 4K HDMI signals. We highly
recommend Gefen HDMI cables. They have been designed and tested to reliably
transport the full throughput of HDMI standard.
•
Power Over HDBaseT (POH) is a standard HDBaseT™ implementation of PoE
that provides power from one device to the other over the link cable. While this
Sender and Receiver units comply with the POH standard, the EXT-UHDA-HBTL-RX
Receiver unit can power the Sender, but the EXT-UHDV-WP-HBTLS-TX Sender can
only receive power from the Receiver. In applications where the EXT-UHDV-WPHBTLS-TX is used with a non-POH receiver, the Sender will need to be powered
locally by a 12V power supply, sold separately. Please see instructions on page 18 of
this manual regarding powering the Sender unit locally.
•
The EXT-UHDV-WP-HBTLS-TX is HDCP 1.4 compliant. Although the EXTUHDA-HBTL-RX can pass both HDCP 2.2 and 1.4, when the two units are used
together, only HDCP 1.4 will pass through.
•
The information in this manual has been carefully checked and is believed
to be accurate. However, Gefen and Core Brands, LLC assume no responsibility for
any inaccuracies that may be contained in this manual. In no event will Gefen and
Core Brands, LLC be liable for direct, indirect, special, incidental, or consequential
damages resulting from any defect or omission in this manual.
•
All information contained herein is subject to change without notice.
5
Licensing
This product may use software that is subject to open source licenses, including one or more of
the General Public License Version 2 and Version 2.1, Lesser General Public License Version 2.1
and Version 3, BSD, and BSD-style licenses. Distribution and use of this product is subject to
the license terms and limitations of liability provided in those licenses. Specific license terms
and Copyright Notifications are provided in the source code.
For three years from date of activation of this product, any party may request, and we will
supply, for software covered by an applicable license (e.g. GPL or LGPL), a complete machinereadable copy of the corresponding open source code on a medium customarily used for
software interchange. The following software and libraries are included with this product and
subject to their respective open source licenses:
•
•
lwIP
jQuery
lwIP is licenced under the BSD licence:
Copyright (c) 2001-2004 Swedish Institute of Computer Science.
All rights reserved.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1.
Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2.
Redistributions in binary form must reproduce the above copyright notice, this list of
conditions and the following disclaimer in the documentation and/or other materials
provided with the distribution.
3.
The name of the author may not be used to endorse or promote products derived from
this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE AUTHOR ``AS IS’’ AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGE.
6
Features
EXT-UHDV-WP-HBTLS-TX*
•
Supports 340 MHz TMDS Clock and data throughput of up to 10.2 Gbps
•
Automatic switching of HDMI and VGA inputs
•
Manual switching of HDMI and VGA inputs via front panel button or RS-232
•
VGA scaling up to 1920 x 1200 with picture adjustments
•
Extend HDMI, VGA with analog audio, and RS-232 over a single CAT-5e:
4K Ultra HD (3840 x 2160 @ 60 Hz, 4:2:0), up to 130 ft/40 m, 8-bit color (HDMI only)
4K Ultra HD (3840 x 2160 @ 30 Hz, 4:4:4), up to 130 ft/40 m, 8-bit color (HDMI only)
4K Cinema (DCI) (4096 x 2160 @ 24 or 30 Hz 4:4:4), up to 130 ft/40 m, 8-bit color
(HDMI only)
1080p Full HD (60 Hz) or WUXGA (1920x1200 @ 60 Hz), up to 230 ft/70 m, up to 12-bit Deep Color
•
HDMI Features Supported:
HDMI 2.0
HDCP 1.4
12-bit Deep Color (at 1080p)
LPCM 7.1, Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™ pass-
through
3DTV pass-through
CEC pass-through
Lip Sync pass-through
•
Analog L/R audio input for VGA
•
RS-232 control of switching, scaler, and EDID management functions
•
Bi-Directional RS-232 extension when used with EXT-UHDA-HBTL-RX
•
Power over HDBaseT™ (POH) provides power to the Sender from a compatible Receiver
over the link cable
•
Sender can also be locally powered using the 2-pin Phoenix connector on back panel
•
Uses Gefen’s implementation of HDBaseT™ technology with enhanced features
•
Advanced EDID Management for rapid integration of source and display
•
Field-updateable firmware via USB Micro-B and RS-232 ports, using the Gefen Syner-G™
software
•
North American standard 2-gang wall-plate form factor
•
Works with most standard North American 2-gang Decora® wall-plates (white wall-plate
is included)
•
Works with most North American 2-gang table boxes and “open-back” low-voltage
installation brackets
*Features and specifications are subject to change without notice.
7
Features
EXT-UHDA-HBTL-RX*
•
Supports 340 MHz TMDS Clock and data throughput of up to 10.2 Gbps
•
Extends HDMI, 2-way IR, and RS-232 over a single CAT-5e:
4K Ultra HD (3840 x 2160 @ 60 Hz, 4:2:0), up to 130 ft/40 m, 8-bit color
4K Ultra HD (3840 x 2160 @ 30 Hz, 4:4:4), up to 130 ft/40 m, 8-bit color
4K Cinema-DCI (4096 x 2160 @ 24 or 30 Hz 4:4:4), up to 130 ft/40 m, 8-bit color
1080p Full HD (60 Hz) or WUXGA (1920x1200 @ 60 Hz), up to 230 ft/70 m, up to 12-bit Deep Color
•
HDMI Features Supported:
HDMI 2.0
HDCP 2.2 and 1.4
12-bit Deep Color (at 1080p)
LPCM 7.1, Dolby Atmos®, Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™ pass-
through
3DTV pass-through
CEC pass-through
Lip Sync pass-through
•
RS-232 control of switching, scaler, and EDID management functions of a compatible
Sender (such as EXT-UHDV-WP-HBTLS-TX and EXT-UHDV-HBTLS-TX)
•
Bi-Directional RS-232 extension when used with a compatible Sender (such as EXTUHDV-WP-HBTLS-TX and EXT-UHDV-HBTLS-TX)
•
2-way IR extension when used with a compatible Sender (EXT-UHDV-HBTLS-TX)
•
Digital (optical and coaxial) and Analog audio breakout
•
Bi-Directional Power over HDBaseT™ (POH) provides power to the Receiver or a
compatible Sender unit (such as EXT-UHDV-HBTLS-TX) over the link cable - only one side
will need external power
•
Provides Power over HDBaseT™ (POH) to a compatible Sender unit (such as EXT-UHDVWP-HBTLS-TX) over the link cable
•
Uses Gefen’s implementation of HDBaseT™ technology with enhanced features
•
Locking power connector
•
Compact, ultra-low-profile enclosure is surface-mountable and can be hidden away
8
Packing Lists
EXT-UHDV-WP-HBTLS-TX*
The following items are included in the EXT-UHDV-WP-HBTLS-TX package. If any of these
items are not present in the box when you first open it, please contact Gefen Technical Support
as soon as possible.
(1) 4K Ultra HD Multi-Format 2x1 HDBaseT™ Sender unit
(1) White trim plate
(4) Trim-plate screws
(4) Mounting screws
(1) 2-pin Phoenix plug (attached to unit)
(1) 4-pin Phoenix plug (attached to unit)
(1) Quick Start Guide
EXT-UHDA-HBTL-RX*
The following items are included in the EXT-UHDA-HBTL-RX. If any of these items are not
present in the box when you first open it, please contact Gefen Technical Support as soon as
possible.
(1) 4K Ultra HD HDBaseT™ Receiver unit
(1) 12V DC power supply with locking connector
(1) 3-pin Phoenix plug (attached to unit)
(2) Mounting Brackets
(4) Self-adhesive rubber feet
(1) Quick-Start Guide
*Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
9
Table of Contents
Controls, Connectors, and Indicators.............................................................................11
EXT-UHDV-WP-HBTLS-TX....................................................................................................11
EXT-UHDA-HBTL-RX............................................................................................................. 14
Installation......................................................................................................................17
Physical Installation, EXT-UHDV-WP-HBTLS-TX............................................................... 17
Physical Installation, EXT-UHDA-HBTL-RX........................................................................ 18
+12V Wiring, EXT-UHDV-WP-HBTLS-TX............................................................................ 18
Sample Wiring Diagram........................................................................................................ 19
LED Status.......................................................................................................................20
Scaler Functions and Picture Adjustments.................................................................. 21
EDID Management........................................................................................................22
RS-232............................................................................................................................. 23
Features23.
23
Commands.............................................................................................................................26
Firmware Update...........................................................................................................28
Specifications.................................................................................................................29
10
Controls, Connectors, and Indicators
EXT-UHDV-WP-HBTLS-TX
2
4
3
1
6
Power
Link HDCP
VGA
7
Reset
VGA In
Input
11
5
8
Audio In
Auto
HDMI
9
EXT-UHDV-WP-HBTLS-TX
Syner-G™
HDMI In
10
12
13
14
11
Controls, Connectors, and Indicators
ID
Name
Description
1
Power Indicator
This LED indicator glows solid blue when the
unit is powered. See LED Status (Page 20)
for more information.
2
Link Indicator
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (Page 20) for
more information.
3
HDCP Indicator
This LED indicator glows solid green when the
active HDMI signal contains HDCP encryption.
See LED Status (Page 20) for more
information.
4
VGA Indicator
This LED indicator glows solid green when the
VGA input has been selected. See LED Status
(Page 20) for more information.
5
HDMI Indicator
This LED indicator glows solid green when the
HDMI input has been selected. See LED Status
(Page 20) for more information.
6
Reset Button
Press and release this button with a thin
blunt object to perform a “soft” reset.
7
VGA Video Input
Connect a VGA cable from your source to
this input.
8
VGA Audio Input
Connect a 3.5mm stereo audio cable from
the analog stereo audio output of your
source to be used with the VGA input.
9
HDMI Input
Connect a Gefen HDMI cable from your
source to this input.
10
Firmware Update Port
To do a firmware update, attach a USB
thumb drive containing the new firmware
to this port, using a USB Micro-B male to
USB Type-A female cable or adaptor. The
Gefen Syner-G™ software, running on a PC
connected to the RS-232 port of the Sender
unit (Page 28) will administer the firmware
update process.
12
Controls, Connectors, and Indicators
ID
Name
Description
11
Input/Auto Switch
To switch between HDMI and VGA inputs,
press and release this button. To activate or
deactivate Auto-Switching, press and hold
this button for 3 seconds or longer until the
function engages or disengages. This button
will be illuminated when Auto-Switching is
active. See LED Status (Page 20) for more
information.
12
HDBaseT™ Link Connector
Connect a CAT-5e or better cable, up to the
recommended length for a given resolution,
from this port to the HDBaseT™ In port on the
Receiver unit. This Sender can receive power
over the CAT-5 cable from a POH compatible
Receiver such as the EXT-UHDA-HBTL-RX,
but it cannot supply power to a Receiver.
13
12V DC Input
While we highly recommend that the Sender
unit is powered through the Receiver unit
via POH, in cases where a non-POH Receiver
is used, the Sender’s 12V DC 2-pin Phoenix
connector can be wired to a 12V power supply
with a current capability of between 1 to 2A.
Please see more details under +12V Wiring for
the EXT-UHDV-WP-HBTLS-TX (Page 18)
14
RS-232 Port
This port can be used for extending 2-way
RS-232 communications between the
Sender and the Receiver, for local control
of the Sender, and for Gefen Syner-G™
interface using an Rs-232 connection with
a computer. Connect Tx, Rx, and Ground
from an automation control device or an
RS-232 device-to-be-controlled, using the
removable 3-pin “Captive Screw” Phoenix
connector. Please note that The Sender and
Receiver’s Tx, Rx, and Ground pin-outs for
their Phoenix connectors are different. To
ensure proper operation, please follow the
pin-out of each connector as printed on each
unit’s enclosure.
13
Controls, Connectors, and Indicators
EXT-UHDA-HBTL-RX
1
Prog 1
RS-232 Pass-Thru
5
6
7
3
4
Link
HDCP
Powe r
EXT-UHDA-HBTL-RX
Prog 2
RS-23 2
Tx G Rx IR In/Ex t IR Out
2
Audi o Ou t
HDM I Ou t
Line
Coax
Optical
HDBaseT ™ In
12 V DC
8
9
10
11
12
13
ID
Name
Description
1
RS-232/Program Switch
This 3-position slide switch places the
unit in RS-232 extension or factory service
modes (Prog 1 and Prog 2). During normal
operation, this switch should be in RS-232
Pass-Thru position.
2
Link Indicator
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (Page 20) for
more information.
3
HDCP Indicator
This LED indicator glows solid green when the
active HDMI signal contains HDCP encryption.
See LED Status (Page 20) for more
information.
4
Power Indicator
This LED indicator glows solid blue when the
unit is powered. See LED Status (Page 20)
for more information.
14
Controls, Connectors, and Indicators
ID
Name
Description
5
RS-232 Port
This port can be used for extending
2-way RS-232 communications between
the Sender and the Receiver, for remote
control of the Sender, for Gefen Syner-G™
interface using an Rs-232 connection with
a computer. Connect Tx, Rx, and Ground
from an automation control device or an
RS-232 device-to-be-controlled, using the
removable 3-pin “Captive Screw” Phoenix
connector. Please note that The Sender and
Receiver’s Tx, Rx, and Ground pin-outs for
their Phoenix connectors are different. To
ensure proper operation, please follow the
pin-out of each connector as printed on each
unit’s enclosure.
6
IR In/Ext
THIS FEATURE IS NOT ACTIVE WHEN
CONNECTED TO EXT-UHDV-WP-HBTLSTX: 3.5mm mini-stereo jack. Connect an IR
Extender (Gefen part no. EXT-RMT-EXTIRN)
to this port. Alternatively, connect a 3.5mm
mini-stereo connector from this port to the
output of an automation system with an
electrical IR output.
7
IR Out
THIS FEATURE IS NOT ACTIVE WHEN
CONNECTED TO EXT-UHDV-WP-HBTLSTX: Connect an EXT-IREMIT IR Emitter (sold
separately) from this port to the IR sensor of
the device to be controlled.
8
HDMI Out
Use a Gefen HDMI cable to connect an
HDMI display to this port.
9
Line Out
This port provides analog Left and Right
channels of audio de-embedded from
the HDMI signal, for use with outboard
amplification. Connect a 3.5mm stereo
audio cable from this port to the analog
stereo input of your amplifier or processor.
15
Controls, Connectors, and Indicators
ID
Name
Description
10
Coaxial Digital Out
This port provides up to 5.1 channels of
Bitstream (Dolby Digital or DTS), or Left
and Right channels of PCM digital audio
de-embedded from the HDMI signal, for
use with outboard amplification. Connect
a coaxial digital audio cable with RCA
connectors from this port to the coaxial
digital input of your amplifier or processor.
11
Optical Digital Out
This port provides up to 5.1 channels of
Bitstream (Dolby Digital or DTS), or Left
and Right channels of PCM digital audio
de-embedded from the HDMI signal, for use
with outboard amplification. Connect an
optical digital audio cable with TOSLINK®
connectors from this port to the optical
digital input of your amplifier or processor.
12
HDBaseT™ In (Link)
Connector
Connect a CAT-5e or better cable, up to the
recommended length for a given resolution,
from this port to the HDBaseT™ Out port on
the Sender unit. This Receiver can send power
over the CAT-5 cable to a POH compliant
Sender unit. It can also receive power over the
CAT-5 cable from a POH compatible Sender
such as the EXT-UHDV-HBTLS-TX, but NOT
the EXT-UHDV-WP-HBTLS-TX.
13
12V DC In
This power receptacle is used to connect the
included 12V DC power supply. As long as the
connected Sender is POH-compliant, it can
get power from this Receiver. Only one power
supply is required for the extender system to
operate.
16
Installation
Physical Installation
EXT-UHDV-WP-HBTLS-TX:
1.
While this wall-plate Sender is a low-voltage device and can usually be mounted in-wall
without an electrical back-box, please check your local electrical code to ensure compliance.
2.
As long as installation without a back-box is acceptable, the unit can be mounted either
directly onto the drywall or other sturdy hollow wall panel, or by using a standard North
American 2-gang low-voltage installation bracket, available from most hardware stores.
3.
Regardless of mounting with or without an installation bracket, make sure that you have
2” or 50mm of clearance behind the outer surface of the wall.
4.
If installing without a bracket, create a 3.6” x 2.8” or 92mm x 72mm (WxH) cutout in the
wall.
5.
Center the wall-plate Sender in the opening, and using it as a template, mark 4 hole
locations on the wall as circled below. Use self-tapping drywall screws if there is wood
bracing directly behind the wall panel for the screws to go through. Otherwise use wallanchors to ensure a secure installation.
Power
Link HDCP
92mm
3.6”
VGA
Reset
VGA In
Input
72mm
2.8”
Audio In
Auto
HDMI
EXT-UHDV-WP-HBTLS-TX
Syner-G™
HDMI In
Wall Cutout
if not using installation frame
6.
If using a low-voltage installation frame, install the frame onto the wall using the instructions that came with the frame. Install the wall-plate sender to this frame, using the 4
long screws that came with your wall-plate sender.
7.
Before attaching the wall-plate sender to the wall, make all wiring connections as per the
instructions earlier in this manual for each port.
8.
Once installation is complete and all functionality has been verified, install the supplied
Decora® trim-plate with the 4 small white screws provided. You can also use a compatible
Decora® trim-plate of your choice.
17
Installation
Physical Installation
EXT-UHDA-HBTL-RX:
1.
The Receiver’s ultra-low-profile enclosure can be hidden behind the display. It also features a pair of mounting brackets that can be attached to each side of the enclosure using
the provided screws.
2.
When surface-mounting the Receiver, please secure it to the mounting surface using
screws appropriate for that specific surface (not included with the product).
+12V Wiring for the EXT-UHDV-WP-HBTLS-TX
While we highly recommend that the Sender unit is powered through the Receiver unit
via POH (Power over HDBaseT), in cases where a non-POH Receiver is used, the Sender’s
+12V DC 2-pin Phoenix connector can be wired to a 12V power supply with a current
capability between 1 to 2A.
This operation should only be performed by a professional and licensed low-voltage
installer who has the proper tools and knowledge. Gefen will not assume any direct or
indirect responsibility or liability for any damage or loss. When wiring a power supply to
the Sender unit, please observe the polarity requirements.
When using a Gefen power supply (EXT-PS121.5-3P-6 or EXT-PS121.5-LP-6), the DC plug
needs to be removed. Please use the following guidelines, but always double-check
polarity and voltage with a DC voltmeter. Furthermore, your warranty may be void in case
of improper wiring or if a non-Gefen power supply is used.
a.
If a Gefen EXT-PS121.5-3P-6 is used, please note that the white wire goes to the
positive (+) terminal of the Phoenix connector.
b.
If a Gefen EXT-PS121.5-LP-6 is used, the black wire with white stripe goes to the
positive (+) terminal of the Phoenix connector.
Important!
Please see information
above before use
18
Installation
Sample Wiring Diagram
CAT-5e CABLE
HDMI CABLE
VGA CABLE
RS-232 CABLE
3.5MM AUDIO CABLE
OPTICAL DIGITAL AUDIO
COAXIAL DIGITAL AUDIO
Power
Link HDCP
VGA
Reset
VGA In
Input
Audio In
Auto
RS-232 Automation
Control Device
or
Device-To-Be-Controlled
HDMI
Powered Speakers
or Audio Amplifier
w/analog L/R input
EXT-UHDV-WP-HBTLS-TX
VGA Source
HDMI In
Firmware
EXT-UHDV-WP-HBTLS-TX
Sender (Front)
Audio Amplifier
w/ coaxial digital input
4K Ultra HD Source
EXT-UHDA-HBTL-RX
Receiver (Back)
HDBaseT™
Out
(POH)
In*
RS-232
* Do NOT connect if using POH
Audio Amplifier
w/ optical digital input
Display
RS-232 Automation
Control Device
or
Device-To-Be-Controlled
EXT-UHDV-WP-HBTLS-TX
Sender (Back)
EXT-UHDV-WP-HBTLS-TX
EXT-UHDA-HBTL-RX
Notes
1. The wiring diagram above shows cables and accessories that may not be included with the products.
Select accessories (as identified by Gefen part numbers) are available for purchase from your Gefen
distributor.
2. Power supply connections are not shown in the diagrams above. We highly recommend that the Power
supply is connected to Receiver and the Sender is powered through the CAT-5 (HDBaseT™ Link) cable. To
power the Sender directly please see information and instructions on previous page.
19
LED Status
The Power, Link, HDCP, HDMI, VGA and Auto/Input indicators on the Sender, and Power,
Link, and HDCP indicators on the Receiver unit provide basic information on the current
status of each unit.
Power
Description
Solid blue
•
The unit is powered.
Off
•
The unit is not powered. Check the power supply and the
Link connection between the Sender and the Receiver unit.
Link
Description
Solid green
•
Link integrity is good between the Sender and Receiver unit.
Off
•
Link is not detected. Check the power supply and the Link
connection between the Sender and the Receiver unit.
HDCP
Description
Solid green
•
The HDMI signal being extended between Sender and
Receiver has HDCP Encryption.
Off
•
Either the VGA or an unencrypted HDMI signal is being
extended.
HDMI (Sender only)
Description
Solid green
•
HDMI Input is selected.
Off
•
VGA input is selected.
VGA (Sender only)
Description
Solid green
•
VGA Input is selected.
Off
•
HDMI input is selected.
Input/Auto* (Sender only)
Description
Solid green
•
Automatic Input Switching is active.
Off
•
Automatic Input Switching is off.
* To Enable/Disable Auto-Switching, press and hold the Input/Auto Button for 3 seconds or longer until the backlight turns on or off.
20
Scaler Functions and Picture Adjustments
The EXT-UHDV-WP-HBTLS-TX features a powerful Scaler for its VGA input. The VGA signal can
be scaled to an array of resolutions, timing, and aspect ratio up to WUXGA (1920 x 1200) at 60
Hz.
Aspect ratio optimization is set to automatic as the default; it will maintain the aspect ratio
of the source. Aspect ratio can also be configured manually via RS-232 commands or Gefen
Syner-G™ software with 4:3 and 16:9 options.
Scaler Output can be set to one of the following:
1 - 1360x768 60 Hz
2 - 1024x768 60 Hz
3 - 1280x720 50 Hz
4 - 1280x720 60 Hz
5 - 1280x800 60 Hz
6 - 1920x1080 50 Hz
7 - 1920x1080 60 Hz
8 - 1920x1200 60 Hz
9 - 1600x1200 60 Hz
The EXT-UHDV-WP-HBTLS-TX also features VGA picture adjustments for the following
parameters:
Color Balance
Color Temperature
Sharpness
Saturation
Brightness
Contrast
Clock
Phase
All of the above scaler and picture adjustment parameters can be configured via RS-232
commands (Page 26) or Gefen Syner-G™ software.
The HDMI input of the EXT-UHDV-WP-HBTLS-TX does not go through the scaler and is passed
through directly to the Receiver via the HDBaseT™ link.
21
EDID Managemnent
The EXT-UHDV-WP-HBTLS-TX features advanced EDID Management capabilities for quick
optimization of a source’s output to best match the display’s capabilities.
EDID Management can be done via RS-232 commands (Page 26) or using the Gefen Syner-G™
software.
When using Gefen Syner-G™, Internal, External, and Custom EDIDs can be downloaded from
the EXT-UHDV-WP-HBTLS-TX, modified via the advanced EDID Editor that is built into the
Gefen Syner-G™ software, and uploaded back into the Sender.
22
RS-232
RS-232 Features
The EXT-UHDV-WP-HBTLS-TX & EXT-UHDA-HBTL-RX, when used together, support the
following RS-232-related functions:
a. Bi-directional RS-232 extension between Sender and Receiver.
b. Control of Sender’s input switching, scaler functions, and EDID management from the
viewing side, via the Receiver’s RS-232 port. This can be done via an automation control device
or the Gefen Syner-G™ software.
c. Gefen Syner-G™ interface via RS-232 ports of Sender and Receiver. Gefen Syner-G™ software
is used for firmware updates and EDID management of the Sender.
Please see the RS-232 commands section (Page 26) on how to configure the Sender and
Receiver to perform the above functions.
a. Bi-directional RS-232 extension between Sender and Receiver:
1.
Connect RS-232 Tx, Rx, and Ground from an automation control device to the
removable 4-pin “Captive Screw” Phoenix connector that is attached to the RS-232
port of the Sender unit. Please note that the upper pin is not used (marked as No
Connection). Each of the remaining 3 pins is identified on the connector panel.
2.
Make sure that the 3 position slide switch on the front panel of the Receiver is set
to RS-232 Pass-Thru mode. Connect RS-232 Tx, Rx, and Ground from the deviceto-be-controlled, to the removable 3-pin “Captive Screw” Phoenix connector that is
attached to the RS-232 port of the Receiver unit. Each of the 3 pins is identified on
the top panel, near the connector.
3.
Since RS-232 is a bi-directional communications protocol, you can also connect the
automation controller to the receiver and the device-to-be-controlled to the sender,
depending on your application.
Please note that The Sender and Receiver’s Tx, Rx, and Ground pin-outs for their
Phoenix connectors are different. To ensure proper operation, please follow the pinout of each connector as printed on each unit’s enclosure.
23
RS-232
b. Control of Sender’s input switching, scaler functions, and EDID mangement from the
viewing side, via the Receiver’s RS-232 port:
1.
Connect RS-232 Tx, Rx, and Ground from a computer with a Serial (RS-232) port, or
using a USB-to-RS-232 adapator, to the removable 4-pin “Captive Screw” Phoenix
connector that is attached to the RS-232 port of the Sender unit. Please note that
the upper pin is not used (marked as No Connection). Each of the remaining 3 pins
is identified on the connector panel.
2.
Establish Serial (RS-232) communications between the computer and the Sender
unit. Send the #SET_RS232_MODE 2 command to the Sender to place it in “RemoteEnd-Control” mode. To revert the Sender to its default RS-232 extension mode, the
RS-232 command #SET_RS232_MODE 1 needs to be sent from the Receiver.
3.
Disconnect the PC from the Sender unit. Wire the Sender unit as needed and install
it in its location.
4.
Make sure that the 3 position slide switch on the front panel of the Receiver is set to
RS-232 Pass-Thru mode. Connect RS-232 Tx, Rx, and Ground from an automation
control device to the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Receiver unit. Each of the 3 pins is identified on the
top panel, near the connector.
5.
Program your automation control decvice with the RS-232 control commands (Page
26) for the EXT-UHDV-WP-HBTLS-TX. All commands sent to the RS-232 port of the
Receiver unit will be extended to the Sender unit via the HDBaseT™ Link cable.
Please note that The Sender and Receiver’s Tx, Rx, and Ground pin-outs for their
Phoenix connectors are different. To ensure proper operation, please follow the pinout of each connector as printed on each unit’s enclosure.
24
RS-232
c. Interface with Gefen Syner-G™ via RS-232 ports of Sender and Receiver.:
1.
Direct interface with the Sender: Connect RS-232 Tx, Rx, and Ground from a computer
with a Serial (RS-232 port), or using a USB-to-RS-232 adaptor, to the removable 4-pin
“Captive Screw” Phoenix connector that is attached to the RS-232 port of the Sender
unit. Please note that the upper pin is not used (marked as No Connection). Each of the
remaining 3 pins is identified on the connector panel. If the Sender was configured to
be in “Remote-End-Control” mode (see section (b) on previous page), return it to its
default mode by following step (2) of section (b).
2.
Direct interface with the Receiver: Since the Receiver does not have any customizable
features , it cannot be used with Gefen Syner-G™.
3.
Interface with the Sender by connecting through the Receiver:
i.
Place the Sender unit in “Remote-End-Control” mode (see section (b) on previous
page for details). Wire the Sender unit as needed and install it in its location.
ii.
Make sure that the 3 position slide switch on the front panel of the Receiver is set to
RS-232 Pass-Thru mode.
iii.
Connect RS-232 Tx, Rx, and Ground from a computer with a Serial (RS-232 port),
or using a USB-to-RS-232 adaptor, to the removable 3-pin “Captive Screw” Phoenix
connector that is attached to the RS-232 port of the Receiver unit.
Please note that The Sender and Receiver’s Tx, Rx, and Ground pin-outs for their Phoenix connectors are different. To ensure proper operation, please follow the pin-out of
each connector as printed on each unit’s enclosure.
25
RS-232
RS-232 Commands (EXT-UHDV-WP-HBTLS-TX)
26
RS-232
27
Firmeware Update
Firmware Update
1.
Over time, the Sender unit may require a firmware update to add functionality or fix
issues.
2.
To perform a firmware update, a Windows PC that is running the Gefen Syner-G™
software needs to be connected to to the RS-232 port of the Sender. Use direct RS-232
connection if your PC has a serial port. If not, use a USB-to-RS-232 adapator.
3.
To update the Sender unit, the Gefen Syner-G™software will send the necessary
commands to place the product into firmware update mode. The firmware will be loaded
into the Sender from a USB thumb drive, connected to the Micro-USB Firmware port on
the Sender’s front panel via a USB-Micro-B-male-to-USB-Type-A-female cable or adaptor
(available from major electronics stores).
4.
Follow on-screen instructions in Gefen Syner-G™ to perform the firmware update.
5.
Once a unit has successfully been updated, cycle the power by removing power from the
Sender unit, wait for the Power LED to deactivate, and then reconnect the power supply.
28
Specifications*
EXT-UHDV-WP-HBTLS-TX
Supported Formats
Maximum Video Resolution/Timing
HDMI:
•
4K Cinema - DCI (4096 x 2160 to 60Hz, 4:2:0)
•
4K Ultra HD (3840 x 2160 to 60Hz, 4:2:0)
VGA:
•
WUXGA (1920x1200 to 60 Hz 4:4:4)
Audio (HDMI Pass-Thru)
•
Up to 8 channels of HBR, Bitstream, & LPCM
HDCP
•
1.4
•
•
1 x HDMI Type A 19-pin, locking, female
1 x VGA HD-15, female
Connectors & Indicators
Video Input Connectors
L/R Analog VGA Audio Input Connector •
1 x 3.5mm mini-stereo jack
HDBaseT™ Link Connector
•
1 x RJ-45, shielded
Firmware Update Connector
•
1 x USB Micro-B, female
RS-232 Connector
•
1 x 4-pin Phoenix
Power Connector
•
1 x 2-pin Phoenix (see Page 18 before use)
Recommended Power Supply
(sold separately - DC plug needs to be
removed)
•
EXT-PS121.5AIP-3P-6 or EXT-PS121.5AIP-LP-6
Auto-Manual Switch
•
1 x tact-type, green backlight
Power Indicator
•
1 x LED, blue
Link Indicator
•
1 x LED, green
HDCP Indicator
•
1 x LED, green
HDMI Indicator
•
1 x LED, green
VGA Indicator
•
1 x LED, green
TMDS Clock
•
340 MHz
Video Bandwidth
•
10.2 Gbps
Power Consumption
•
6W maximum
Operating Temperature
•
+32 to +122 °F (0 to +50 °C)
Operating Humidity
•
5% to 90% RH, non-condensing
Storage Temperature
•
-4 to +185 °F (-20 to +85 °C)
Storage Humidity (RH)
•
0% to 95% RH, non-condensing
MTBF
•
50000 hours
Operational
29
Specifications*
Physical
Dimensions
(W x H x D, not including connectors)
•
3.5” x 4.2” x 1.74” (89mm x 104.5mm x 44mm)
Mounting Cavity Dimensions
•
(W x H x D, behind the mounting plate)
3.6” x 2.8” x 2” (92mm x 72mm x 50mm)
Net Weight
0.6 lbs (0.27 kg)
•
* Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
Copyright© 2018 Nortek Security & Control, LLC
30
Specifications*
EXT-UHDA-HBTL-RX
Supported Formats
Maximum Video Resolution/Timing
HDMI:
•
4K Cinema - DCI (4096 x 2160 to 60Hz, 4:2:0)
•
4K Ultra HD (3840 x 2160 to 60Hz, 4:2:0)
VGA:
•
WUXGA (1920x1200 to 60 Hz 4:4:4)
Audio (HDMI Pass-Thru)
•
Up to 8 channels of HBR, Bitstream, & LPCM
Audio (De-Embedded)
•
Up to 6 channels of Bitstream, or 2 ch of LPCM
HDCP
•
2.2 and 1.4
Video Output Connector
•
1 x HDMI Type A 19-pin, female
De-Embedded Audio Output Ports
•
•
•
L/R Analog: 1 x 3.5mm mini-stereo jack
Coaxial Digital: 1 x RCA, female
Optical Digital: 1 x TOSLINK®
HDBaseT™ Link Connector
•
1 x RJ-45, shielded
RS-232 Connector
•
1 x 3-pin Phoenix
Firmware Update Port
•
1 x USB Micro-B, female
IR Extender Type**
•
EXT-RMT-EXTIRN
IR In/Ext Connector**
•
1 x 3.5mm mini-stereo, female
IR Out Connector**
•
1 x 3.5mm mini-stereo, female
Power Connector
•
1 x 12V DC, locking, 5.5mm barrel/2.1mm pin
RS-232/Program Switch
•
1 x 3-position, slide-type
Power Indicator
•
1 x LED, blue
Link Indicator
•
1 x LED, green
HDCP Indicator
•
1 x LED, green
TMDS Clock
•
340 MHz
Video Bandwidth
•
10.2 Gbps
Power Consumption
•
•
Not powering a Sender: 9W maximum
Powering a Sender: 22W maximum
Operating Temperature
•
+32 to +122 °F (0 to +50 °C)
Operating Humidity
•
5% to 90% RH, non-condensing
Storage Temperature
•
-4 to +185 °F (-20 to +85 °C)
Storage Humidity (RH)
•
0% to 95% RH, non-condensing
MTBF
•
Connectors & Indicators
Operational
50000 hours
31
Specifications*
Physical
Dimensions
(W x H x D, not including connectors)
Not including mounting brackets:
•
6” x 0.65” x 4” (152mm x 17 x 100mm)
Including mounting brackets:
•
7” x 0.65” x 4” (178mm x 17 x 100mm)
Net Weight
•
0.6 lbs. (0.27 kg)
* Features and specifications are subject to change without notice.
** IR Extension feature is NOT active when used with EXT-UHDV-WP-HBTLS-TX
All trademarks and registered trademarks are properties of their respective owners.
Copyright© 2018 Nortek Security & Control, LLC
32
5919 Sea Otter Place, Suite 100 , Carlsbad, CA 92010, USA
1800 S McDowell Blvd, Petaluma, CA 94954, USA
1-707-283-5900 1-800-472-5555
Copyright© 2018 Nortek Security & Control, LLC
Part Number: MAN-EXT-UHDV-WP-HBTLS Version A2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising