Gefen | GTB-UHD600-HBTL | Gefen GTB-UHD600-HBTL Manual | Gefen GTB-UHD600-HBT 4K Ultra HD 600 MHz HDBaseT Extender w/ HDR, RS-232, 2-way IR, and POL Manual

Gefen GTB-UHD600-HBT 4K Ultra HD 600 MHz HDBaseT Extender w/ HDR, RS-232, 2-way IR, and POL Manual
4K Ultra HD 600 MHz
HDBaseT™ Extenders
GTB-UHD600-HBT
GTB-UHD600-HBTL
User Manual
Version A2
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install or place this product near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two blades
and a third grounding prong. The wide blade or the third prong are provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.
Only use attachments/accessories specified by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or touch
this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13.
Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15.
Batteries that may be included with this product and/or accessories should never be
exposed to open flame or excessive heat. Always dispose of used batteries
according to the instructions.
2
Warranty Information
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Connect section of the Gefen website at http://www.gefen.com/connect/warranty-andreturn-policy
3
Contact Us
Technical Support
1-707-283-5900
1-800-472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacific Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Core Brands, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
© 2017 Core Brands, LLC. All Rights Reserved.
All trademarks are the property of their respective owners.
Gefen and Core Brands, LLC reserve the right to make changes in the hardware,
packaging, and any accompanying documentation without prior notice.
4
Operating Notes
•
Important
•
While Unshielded (UTP) CAT-5e is usually adequate, shielded (STP) CAT-6A is recommended. Shielded (STP) CAT-5e or unshielded (UTP) CAT-5e or CAT6A may be acceptable depending on cable quality. Care should always be given
to keep these cables away from power lines and other sources of electromagnetic
interference.
•
Cable quality is critical when handling 600 MHz HDMI signals. We highly
recommend 10-foot or shorter Gefen Locking HDMI cables. They have been
designed and tested to work at 600 MHz and reliably transport the the full 18.2
Gbps throughput of HDMI 2.0.
•
The Sender unit has 2 EDID Management DIP Switches on its bottom panel,
under a self-adhesive cover. This product is shipped with its DIP switches set to
enable 4K with 2-Channel Audio mode (SW1: ON, SW2: OFF). Please see the manual
for details before changing the DIP Switch settings.
•
The GTB-UHD600-HBT and GTB-UHD600-HBTL vary in maximum extension
distances, based on resolution / timing and color depth. Refer to the Features
section on pages 6 and 7 for more information .
•
Power Over Line (POL) is a proprietary Gefen implementation that provides
power over the link cable. The GTB-UHD600-HBT and GTB-UHD600-HBTL feature
Bi-Directional POL, meaning that the power supply (1 pc included) can be connected
to either the Sender or the Receiver unit.
•
The information in this manual has been carefully checked and is believed
to be accurate. However, Gefen and Core Brands, LLC assume no responsibility for
any inaccuracies that may be contained in this manual. In no event will Gefen and
Core Brands, LLC be liable for direct, indirect, special, incidental, or consequential
damages resulting from any defect or omission in this manual.
•
All information contained herein is subject to change without notice.
This product uses UL-Listed power supplies
5
Features & Packing List
Features (GTB-UHD600-HBT)*
•
Supports 18.2 Gbps bandwidth and 600 MHz TMDS clock
•
Extends HDMI, RS-232, & Bi-Directional IR over a single CAT-5e/CAT-6A:
•
*
4K Ultra HD (3840 x 2160 to 60 Hz, 4:4:4), up to 264 feet/80 meters (8-bit color)
*
4K Cinema (DCI) (4096 x 2160 to 60 Hz 4:4:4), up to 264 feet/80 meters (8-bit color)
*
1080p Full HD (60 Hz) and WUXGA (1920 x 1200 to 60 Hz), up to 330 feet/100
meters (up to 12-bit Deep Color)
HDMI Features Supported:
*
HDMI 2.0 (full bandwidth to 18.2 Gbps/600 MHz)
*
HDR-10: 10-bit color at 4K 60 Hz 4:2:0 and 4K 24 Hz 4:4:4
*
Dolby® Vision™ HDR: 12-bit color at 4K 60Hz 4:2:0 and 4K 24 Hz 4:4:4
*
HDCP 2.2 and 1.4
*
12-bit Deep Color (at 1080p)
*
Uncompressed LPCM digital audio up to 7.1 channels
*
HBR (High Bit Rate) digital audio up to 7.1 channels, including Dolby Atmos®,
Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™
*
3DTV pass-through
*
CEC pass-through
*
Lip Sync pass-through
•
Supports the use of DVI sources and DVI displays up to 1080p Full HD and WUXGA
(1920x1200), with Gefen CAB-DVI2HDMI-LCK DVI-to-HDMI cables (not included)
•
RS-232 2-way link between Sender and Receiver
•
IR extension from Sender to Receiver and from Receiver to Sender
•
Gefen’s Bi-Directional POL provides power to the Sender or the Receiver unit over the link
cable - only one side will need external power
•
Uses Gefen’s implementation of HDBaseT™ technology with proprietary algorithms and
enhanced features
•
Advanced EDID Management
•
Firmware updatable via RS-232 using Gefen Syner-G™
•
Locking power connector
•
Plug & Play – no configuration or set-up required for most applications
•
Surface mountable
•
Compact enclosures are easy to install and can be hidden away
*Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
6
Features & Packing List
Features (GTB-UHD600-HBTL)*
•
Supports 18.2 Gbps bandwidth and 600 MHz TMDS clock
•
Extends HDMI & Bi-Directional IR over a single CAT-5e/CAT-6A:
•
*
4K Ultra HD (3840 x 2160 to 60 Hz, 4:4:4), up to 132 feet/40 meters (8-bit color)
*
4K Cinema (DCI) (4096 x 2160 to 60 Hz 4:4:4), up to 132 feet/40 meters (8-bit color)
*
1080p Full HD (60 Hz) and WUXGA (1920 x 1200 to 60 Hz), up to 200 feet/60 meters
(up to 12-bit Deep Color)
HDMI Features Supported:
*
HDMI 2.0 (full bandwidth to 18.2 Gbps/600 MHz)
*
HDR-10: 10-bit color at 4K 60 Hz 4:2:0 and 4K 24 Hz 4:4:4
*
Dolby® Vision™ HDR: 12-bit color at 4K 60Hz 4:2:0 and 4K 24 Hz 4:4:4
*
HDCP 2.2 and 1.4
*
12-bit Deep Color (at 1080p)
*
Uncompressed LPCM digital audio up to 7.1 channels
*
HBR (High Bit Rate) digital audio up to 7.1 channels, including Dolby Atmos®,
Dolby® TrueHD, DTS:X™, and DTS-HD Master Audio™
*
3DTV pass-through
*
CEC pass-through
*
Lip Sync pass-through
•
Supports the use of DVI sources and DVI displays up to 1080p Full HD and WUXGA
(1920x1200), with Gefen CAB-DVI2HDMI-LCK DVI-to-HDMI cables (not included)
•
IR extension from Sender to Receiver and from Receiver to Sender
•
Gefen’s Bi-Directional POL provides power to the Sender or the Receiver unit over the link
cable - only one side will need external power
•
Uses Gefen’s implementation of HDBaseT™ technology with proprietary algorithms and
enhanced features
•
Advanced EDID Management
•
Firmware updatable via Gefen Syner-G™ port
•
Locking power connector
•
Plug & Play – no configuration or set-up required for most applications
•
Surface mountable
•
Compact enclosures are easy to install and can be hidden away
*Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
7
Features & Packing List
Packing List* (GTB-UHD600-HBT)
The following items are included in the GTB-UHD600-HBT package. If any of these items are
not present in the box when you first open it, please contact Gefen Technical Support as soon
as possible.
(1)
(1)
(1)
(1)
(1)
(1)
Sender Unit (GTB-UHD600-HBT-TX)
Receiver Unit (GTB-UHD600-HBT-RX)
HDMI-to-HDMI Male-to-Male Locking cable, 6 feet
IR Emitter (EXT-IREMIT)
IR Extender (EXT-RMT-EXTIRN)
12V DC power supply with US/EU/UK/AU reginal AC plugs and 5.5mm/2.1mm DC
plug (EXT-PS121.5AIP-LP-6)
Packing List* (GTB-UHD600-HBTL)
The following items are included in the GTB-UHD600-HBTL. If any of these items are not
present in the box when you first open it, please contact Gefen Technical Support as soon as
possible.
•
•
•
•
•
•
(1)
(1)
(1)
(1)
(1)
(1)
Sender Unit (GTB-UHD600-HBTL-TX)
Receiver Unit (GTB-UHD600-HBTL-RX)
HDMI-to-HDMI Male-to-Male Locking cable, 6 feet
IR Emitter (EXT-IREMIT)
IR Extender (EXT-RMT-EXTIRN)
12V DC power supply with US/EU/UK/AU reginal AC plugs and 5.5mm/2.1mm DC
plug (EXT-PS121.5AIP-LP-6)
*Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
8
Table of Contents
Introduction.................................................................................................................... 10
GTB-UHD600-HBT................................................................................................................10
GTB-UHD600-HBTL.............................................................................................................. 15
Installation.....................................................................................................................20
Connection Instructions....................................................................................................... 20
Sample Wiring Diagrams...................................................................................................... 21
LED Status.......................................................................................................................22
IR Control........................................................................................................................ 23
Controlling the Source from the Viewing Location..............................................................23
Controlling the Display from the Source Location...............................................................24
Controlling the Source / Display from the Head-End and Viewing Locations�������������������25
DIP Switch Configuration..............................................................................................26
EDID Management................................................................................................................26
RS-232*............................................................................................................................ 27
Firmware Update...........................................................................................................28
Specifications.................................................................................................................29
* GTB-UHD600-HBT only
9
Introduction
GTB-UHD600-HBT
Sender Unit
1
3
GTB-UHD600-HBT-TX
Link
Power
HDMI
2
Link
Tx Rx G
On ON
Off
5
IR Out
RS-232
Prog
HDMI In
6
7
8
9
10
1 2
4
1
IR In/Ext
ON
12V DC
11
10
Introduction
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered. See LED Status (page 22)
for more information.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (page 22) for
more information.
3
HDMI
This LED indicator glows solid green when
a source is connected to the HDMI In port.
See LED Status (page 22) for more
information.
4
12V DC
This power receptacle is used to connect the
included 12V DC power supply. Only one power
supply is required for the extender system to
operate. The power supply can be connected
to either the Sender or Receiver unit.
5
Link
Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length
for a given resolution, from this port to the Link
port on the Receiver unit.
6
IR In/Ext
3.5mm mini-stereo jack. Connect an IR
Extender (Gefen part no. EXT-RMT-EXTIRN)
to this port. Alternatively, connect a 3.5mm
mini-stereo connector from this port to the
output of an automation system with an
electrical IR output.
See IR Control (page 23) for more
information on using IR.
7
IR Out
Connect an EXT-IREMIT IR Emitter (1 pc
included) from this port to the IR sensor of the
device to be controlled.
See IR Control (page 23) for more
information on using IR.
11
Introduction
ID
Name
Description
8
RS-232
Connect RS-232 Tx, Rx, and Ground from
an automation control device, using the
removable 3-pin “Captive Screw” Phoenix
connector that is attached to the RS-232
port of the Sender unit.
9
Prog
For normal operation, this switch should be in
the Off (down) position. Setting this switch
to the On (up) position, places the unit in
firmware update mode. If either the Sender
or the Receiver switch is in On position,
extenders will not work. For the new setting
of this switch to take effect, power needs to
be removed from the unit by removing and
reinstated by reconnecting them.
10
HDMI In
Use the included Locking HDMI cable to
connect an Ultra HD source to this HDMI
port.
11
DIP Switches
These DIP switches provide EDID
management. See DIP Switch Configuration
(page 26) for more information.
Receiver Unit
1
3
GTB-UHD600-HBT-RX
Link
Power
HDMI
2
Link
Tx Rx G
On ON
Off
12V DC
4
5
1
IR In/Ext
IR Out
RS-232
Prog
HDMI Out
6
7
8
9
10
12
Introduction
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered. See LED Status (page 22)
for more information.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (page 22) for
more information.
3
HDMI
This LED indicator glows solid green when
a source is connected to the HDMI In port.
See LED Status (page 22) for more
information.
4
12V DC
This power receptacle can be used to connect
the included 12V DC power supply. Only one
power supply is required for the extender
system to operate. The power supply can be
connected to either the Sender or Receiver
unit.
5
Link
Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length
for a given resolution, from this port to the Link
port on the Sender unit.
6
IR In/Ext
3.5mm mini-stereo jack. Connect an IR
Extender (Gefen part no. EXT-RMT-EXTIRN)
to this port. Alternatively, connect a 3.5mm
mini-stereo connector from this port to the
output of an automation system with an
electrical IR output.
See IR Control (page 23) for more
information on using IR.
7
IR Out
Connect an EXT-IREMIT IR Emitter (1 pc
included) from this port to the IR sensor of the
device to be controlled.
See IR Control (page 23) for more
information on using IR.
13
Introduction
ID
Name
Description
8
RS-232
Connect Tx, Rx, and Ground from an
automation control device, using the
removable 3-pin “Captive Screw” Phoenix
connector that is attached to the RS-232
port of the Receiver unit.
9
Prog
For normal operation, this switch should be in
the Off (down) position. Setting this switch
to the On (up) position, places the unit in
firmware update mode. If either the Sender
or the Receiver switch is in On position,
extenders will not work. For the new setting
of this switch to take effect, power needs to
be removed from the unit by removing and
reinstated by reconnecting them.
10
HDMI Out
Use a Gefen Locking HDMI cable, up to 10
feet long, to connect an Ultra HD display to
this HDMI port.
14
Introduction
GTB-UHD600-HBTL
Sender Unit
1
3
GTB-UHD600-HBTL-TX
Link
Power
HDMI
2
Tx Rx G
On ON
Off
4
IR In/Ext
5
6
IR Out Syner-G™
7
8
1
Prog
HDMI In
9
10
ON
12V DC
1 2
Link
11
15
Introduction
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered. See LED Status (page 22)
for more information.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (page 22) for
more information.
3
HDMI
This LED indicator glows solid green when
a source is connected to the HDMI In port.
See LED Status (page 22) for more
information.
4
12V DC
This power receptacle can be used to connect
the included 12V DC power supply. Only one
power supply is required for the extender
system to operate. The power supply can be
connected to either the Sender or Receiver
unit.
5
Link
Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length
for a given resolution, from this port to the Link
port on the Receiver unit.
6
IR In/Ext
3.5mm mini-stereo jack. Connect an IR
Extender (Gefen part no. EXT-RMT-EXTIRN)
to this port. Alternatively, connect a 3.5mm
mini-stereo connector from this port to the
output of an automation system with an
electrical IR output.
See IR Control (page 23) for more
information on using IR.
7
IR Out
Connect an EXT-IREMIT IR Emitter (1 pc
included) from this port to the IR sensor of the
device to be controlled.
See IR Control (page 23) for more
information on using IR.
16
Introduction
ID
Name
Description
8
Syner-G™
This port is used for firmware update using
Gefen Syner-G™
9
Prog
For normal operation, this switch should be in
the Off (down) position. Setting this switch
to the On (up) position, places the unit in
firmware update mode. If either the Sender
or the Receiver switch is in On position,
extenders will not work. For the new setting
of this switch to take effect, power needs to
be removed from the unit by removing and
reinstated by reconnecting them.
10
HDMI In
Use the included Locking HDMI cable to
connect an Ultra HD source to this HDMI
port.
11
DIP Switches
These DIP switches provide EDID
management. See DIP Switch Configuration
(page 26) for more information.
Receiver Unit
1
3
GTB-UHD600-HBTL-RX
Link
Power
HDMI
2
Link
Tx Rx G
On ON
Off
12V DC
4
IR In/Ext
5
6
IR Out Syner-G™
7
8
17
1
Prog
HDMI Out
9
10
Introduction
ID
Name
Description
1
Power
This LED indicator glows solid blue when the
unit is powered. See LED Status (page 22)
for more information.
2
Link
This LED glows solid green when a link
is established between the Sender and
Receiver. See LED Status (page 22) for
more information.
3
HDMI
This LED indicator glows bright blue when an
source is connected to the HDMI In port.
4
12V DC
This power receptacle can be used to connect
the included 12V DC power supply. Only one
power supply is required for the extender
system to operate. The power supply can be
connected to either the Sender or Receiver
unit.
5
Link
Connect a CAT-5e or better cable, shielded CAT6A preferred, up to the recommended length
for a given resolution, from this port to the Link
port on the Sender unit.
6
IR In/Ext
3.5mm mini-stereo jack. Connect an IR
Extender (Gefen part no. EXT-RMT-EXTIRN)
to this port. Alternatively, connect a 3.5mm
mini-stereo connector from this port to the
output of an automation system with an
electrical IR output.
See IR Control (page 23) for more
information on using IR.
7
IR Out
Connect an EXT-IREMIT IR Emitter (1 pc
included) from this port to the IR sensor of the
device to be controlled.
See IR Control (page 23) for more
information on using IR.
8
Syner-G™
This port is used for firmware update using
Gefen Syner-G™
18
Introduction
ID
Name
Description
9
Prog
For normal operation, this switch should be in
the Off (down) position. Setting this switch
to the On (up) position, places the unit in
firmware update mode. If either the Sender
or the Receiver switch is in On position,
extenders will not work. For the new setting
of this switch to take effect, power needs to
be removed from the unit by removing and
reinstated by reconnecting them.
10
HDMI Out
Use a Gefen Locking HDMI cable, up to 10
feet long, to connect an Ultra HD display to
this HDMI port.
19
Installation
Connection Instructions
►► Video
1.
Connect the included HDMI locking cable between the Ultra Hi-Def source and the
HDMI In port on the Sender unit.
2.
Connect an Ultra HD display to the HDMI Out port on the Receiver unit using another
Gefen HDMI locking cable.
►► CAT-5
3.
Connect a CAT-5e or better cable, shielded CAT-6A preferred, from the Link port on the
Sender unit to the Link port on the Receiver unit.
Note
Video resolution will affect maximum extension distance. Please see the
Specifications section for recommended cable lengths.
►► IR
4.
Refer to IR Control (page 23) for details on connecting IR devices.
►► RS-232 (GTB-UHD600-HBT only)
5.
Connect Tx, Rx, and Ground from the RS-232 port of an automation control unit or a
device-to-be-controlled, using the removable 3-pin “Captive Screw” Phoenix connector
that is attached to the RS-232 ports of the Sender and Receiver units. Each of the 3 pins is
identified on the connector panel.
►► Power
6.
Connect the included 12V DC power supply to the power receptacle on either the Sender
or Receiver unit. Power to the other unit will be supplied through the Link cable.
7.
Connect the AC plug of the power supply to an available electrical outlet.
20
Installation
Sample Wiring Diagrams
IR Extender
(EXT-RMT-EXTIRN)
OR
4K Ultra HD
600 MHz Source
CAT-5e CABLE
HDMI CABLE
RS-232 CABLE
IR IN
IR OUT
Automation
Control Device
GTB-UHD600-HBT-RX
Receiver Unit
OR
IR Emitter
(EXT-IREMIT)
OR
IR Extender
(EXT-RMT-EXTIRN)
RS-232 Controlled
Device
GTB-UHD600-HBT-TX
Sender Unit
Automation
Control Device
IR Emitter
(EXT-IREMIT)
4K Ultra HD 600 MHz Display
GTB-UHD600-HBT
CAT-5e or better CABLE
HDMI CABLE
IR IN
IR Extender
(EXT-RMT-EXTIRN)
OR
4K Ultra HD
600 MHz Source
IR OUT
Automation
Control Device
GTB-UHD600-HBTL-RX
Receiver Unit
IR Emitter
OR
Automation
Control Device
IR Extender
(EXT-RMT-EXTIRN)
GTB-UHD600-HBTL-TX
Sender Unit
IR Emitter
4K Ultra HD 600 MHz Display
GTB-UHD600-HBTL
Notes
1. The wiring diagrams above show an additional IR emitter (Gefen part no. EXT-IREMIT) and IR extender
(Gefen part no. EXT-RMT-EXTIRN) that are not included with the product. These are available for
purchase from your Gefen distributor.
2. Power supply connections are not shown in the diagrams above. Power supply can be connected to
Sender or Receiver. The other unit will recerive power through the link cable,
21
LED Status
The Power, Link, and HDMI LED indicators on the Sender and Receiver unit provide basic
information on the current status of each unit.
The information, in the table below, applies to both the Sender and Receiver unit.
Power
Description
Solid blue
•
The Sender / Receiver unit is powered.
Off
•
Check the power supply and the Link connection between
the Sender and the Receiver unit.
Link
Description
Solid green
•
Link integrity is good between the Sender and Receiver unit.
Off
•
Check the power supply and the Link connection between
the Sender and the Receiver unit.
HDMI
Description
Solid green
•
Sender: Source is connected and powered.
•
Receiver: Display / sink device is connected and powered.
•
Connect a source to the Sender unit; connect a display/sink
to the Receiver unit. Make sure both source and sink are
powered.
Off
22
IR Control
Controlling the Source from the Viewing Location
1.
Connect an EXT-RMT-EXTIRN IR Extender (1 pc included) to the IR In/Ext port on the Receiver
unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR
In/Ext port on the Receiver unit to the IR Output port of the automation system. IR signals
will be transmitted over the Link cable.
2.
Connect an EXT-IREMIT IR Emitter (1 pc included) from the IR Out port of the Sender
unit, to the IR sensor window on the source device.
Ultra HD source
IR signals
Link
IR emitter
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI In
Sender unit
IR signals
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI Out
Receiver unit
to Ultra HD display
IR extender
IR signals
IR signals
or
from Automation
System
23
IR Control
Controlling the Display from the Source Location
1.
Connect an EXT-RMT-EXTIRN IR Extender (1 pc included) to the IR In/Ext port on the Sender
unit. If using an automation system, connect the 3.5mm mini-stereo connector from the IR
In/Ext port on the Receiver unit to the IR Output of the automation system. IR signals will be
transmitted over the Link cable.
2.
Connect an EXT-IREMIT IR Emitter (1 pc included) from the IR Out port on the Receiver unit to
the IR sensor on the display.
IR extender
or
IR signals
from Automation
System
IR signals
from Ultra HD source
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI In
Sender unit
IR signals
Receiver unit
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI Out
IR emitter
Ultra HD display
24
IR Control
Controlling the Source & Display
from the Head-End and Viewing Locations
1.
This set-up ewill require an additional EXT-RMT-EXTIRN and EXT-IREMIT, sold separately by
your Gefen distributor.
2.
Follow instructions on page 23 and 24.
or
IR extender
IR signals
from Automation
System
IR signals
IR emitter
IR Signals from
Receiver unit
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI In
Sender unit
IR signals
Receiver unit
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out Syner-G™
1
Prog
HDMI Out
IR emitter
IR signals
IR extender
IR signals
or
IR Signals from
Sender unit
from Automation
System
25
DIP Switch Configuration
The Sender unit has 2 EDID Management DIP Switches on its bottom panel, under a selfadhesive cover.
This product is shipped with its DIP switches set to enable 4K with 2-Channel Audio mode
(SW1: OFF, SW2: ON).
1 2
ON
1 2
ON
Refer to the table below for DIP switch settings.
EDID Management
SW 1
SW 2
EDID Mode
OFF
N/A
External / Bypass EDID mode (default)
•
ON
N/A
DIP Switch Positions
Allows all video and audio features of the
connected device to be passed to the source
device.
Internal EDID mode
•
ON
1 2
ON
Enables the EDID modes on SW2.
1 2
ON
ON
4K 600 Multichannel Audio EDID mode
•
ON
4K 600 MHz w/ Multichannel Audio
1 2
ON
OFF
4K 600 2-Channel Audio Mode (default)
•
ON
4K 600 MHz w/ 2-Channel Audio
1 2
26
RS-232*
Connecting RS-232 Devices*
The GTB-UHD600-HBT supports RS-232 extension. The RS-232 interface is also used to
upgrade the firmware using the Gefen Syner-G™ software.
1.
Connect RS-232 Tx, Rx, and Ground from an automation control device to the removable
3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the Sender
unit. Each of the 3 pins is identified on the connector panel. If your automation device
has a male DB-9 port and you prefer to not do the wiring, you can purchase an ADA-PH2-DB9-MF-AB adaptor cable from your Gefen distributor. This adaptor cable has a female
DB-9 on one end and a 3-pin Phoenix connector on the other.
2.
Connect RS-232 Tx, Rx, and Ground from the device-to-be-controlled, to the removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 port of the
Receiver unit. Each of the 3 pins is identified on the connector panel. If the RS-232 device
you wish to control has a female DB-9 port and you prefer to not do the wiring, you can
purchase an ADA-PH-2-DB9-MM-AB adaptor cable from your Gefen distributor. This
adaptor cable has a male DB-9 on one end and a 3-pin Phoenix connector on the other.
3.
Since RS-232 is a bi-directional commuinications protocol, and depending on your application, you can also connect the automation controller to the receiver and the device-tobe-controlled to the sender.
Link
Tx Rx G
On ON
Off
12V DC
IR In/Ext
IR Out
RS-232
1
Prog
HDMI Out
Important
The Prog switch must be set to the OFF position in order to enable serial (RS-232)
extension. In addition, when sending RS-232 commands, a CR (0x0D) must be
included.
* GTB-UHD600-HBT only
27
Firmeware Update
Firmware Update
1.
Sender and Receiver should each be updated separately. To ensure proper operation,
always update both units.
2.
A Windows PC that is running Gefen Syner-G™ software, needs to be connected to to the
RS-232 port of the GTB-UHD600-HBT or the Syner-G™ port of the GTB-UHD600-HBTL.
Sender and Receiver, either through a native RS-232 interface or using a USB-to-Serial
adaptor.
3.
Remove power from the unit to be updated, by disconnecting the 12V DC power supply
and the Link connector. Make sure that the Prog switche on the Sender or Receiver is in
On (up) position, and then re-apply power to the unit by connecting the included power
supply to the 12V DC port and to an available electrical outlet. The power LED will glow to
indicate that the unit is receiving power.
4.
Connect RS-232 Tx, Rx, and Ground from the PC or USB-to-Serial adaptor to the
removable 3-pin “Captive Screw” Phoenix connector that is attached to the RS-232 or
Syner-G™ port of the Sender or Receiver to be updated. Each of the 3 pins is identified on
the connector panel. If your PC or USB-to-Serial adaptor has a male DB-9 port and you
prefer to not do the wiring, you can purchase an ADA-PH-2-DB9-MF-AB adaptor cable
from your Gefen distributor. This adaptor cable has a female DB-9 on one end and a 3-pin
Phoenix connector on the other.
5.
Follow on-screen instructions in Gefen Syner-G™ to perform the firmware update on each
unit.
6.
Once a unit has successfully been updated, remove power from the unit, set the Prog
switch to Off (down) position, and reco0nnect the Link cable and the power supply.
28
Specifications*
Supported Formats
Maximum Video Resolution/Timing
•
•
4K Cinema - DCI (4096 x 2160 to 60Hz, 4:4:4)
4K Ultra HD (3840 x 2160 to 60Hz, 4:4:4)
Audio (HDMI Pass-Thru)
•
Up to 8 channels of HBR, Bitstream, & LPCM
Video Input Connector (Sender)
•
1 x HDMI Type A 19-pin, locking, female
Video Output Connector (Receiver)
•
1 x HDMI Type A 19-pin, locking, female
Link Connector (Sender / Receiver)
•
1 x RJ-45, shielded
RS-232 Connector (Sender / Receiver)
•
1 x 3-pin Phoenix (GTB-UHD600-HBT only)
Connectors & Indicators
Syner-G™ Connector (Sender / Receiver) •
1 x 3-pin Phoenix (GTB-UHD600-HBTL only)
IR In/Ext Connector (Sender / Receiver)
•
1 x 3.5mm mini-stereo, female
IR Out Connector (Sender / Receiver)
•
1 x 3.5mm mini-stereo, female
Power Connector (Sender / Receiver)
•
1 x 12V DC, locking, 5.5mm barrel/2.1mm pin
Power Indicator (Sender / Receiver)
•
1 x LED, blue
Link Indicator (Sender / Receiver)
•
1 x LED, green
HDMI Indicator (Sender / Receiver)
•
1 x LED, green
TMDS Clock
•
600 MHz
Video Bandwidth
•
18.2 Gbps
Power Consumption (Sender/Receiver)
•
14 W (max.), combined
Operating Temperature
•
+32 to +113 ºF (0 to +45 ºC)
Operating Humidity
•
5% to 90% RH, non-condensing
Storage Temperature
•
-4 to +185 °F (-20 to +85 °C)
Storage Humidity (RH)
•
0% to 95% RH, non-condensing
MTBF
•
50000 hours
Dimensions (W x H x D)
(Sender / Receiver),
not including connectors
•
4.7” x 1” x 2.9” (119 mm x 26 mm x 73 mm)
Net Weight (Sender/Receiver)
•
0.31 lbs (0.14 kg) each
Operational
Physical
* Features and specifications are subject to change without notice.
All trademarks and registered trademarks are properties of their respective owners.
Copyright© 2017 Core Brands, LLC
29
1800 S McDowell Blvd. Petaluma CA 94954, USA
1-707-283-5900 1-800-472-5555
Copyright© 2017 Core Brands, LLC.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising