Gefen | EXT-DP-4K600-1SC | EXT-DP-4K600-1SC Manual | Gefen EXT-DP-4K600-1SC 4K 600 MHz DisplayPort Extender over one SC-terminated fiber optic cable Manual

Gefen EXT-DP-4K600-1SC 4K 600 MHz DisplayPort Extender over one SC-terminated fiber optic cable Manual
*Preferred
600 MHz
4K ULTRA
60Hz, 4:4:4
DisplayPort ™ 1.2 Extender
over one SC-Terminated Fiber-Optic Cable
EXT-DP-4K600-1SC
H
DUser Manual
R
High Dynamic Range
Release A1
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8.
Do not install or place this product near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. To reduce the risk of electric shock and/or damage to this product, never handle or
touch this unit or power cord if your hands are wet or damp. Do not expose this
product to rain or moisture.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
15. Batteries that may be included with this product and/or accessories should never be
exposed to open flame or excessive heat. Always dispose of used batteries
according to the instructions.
ii
Warranty Information
Gefen warrants the equipment it manufactures to be free from defects in material and
workmanship.
If equipment fails because of such defects and Gefen is notified within two (2) years from
the date of shipment, Gefen will, at its option, repair or replace the equipment, provided
that the equipment has not been subjected to mechanical, electrical, or other abuse or
modifications. Equipment that fails under conditions other than those covered will be
repaired at the current price of parts and labor in effect at the time of repair. Such repairs
are warranted for ninety (90) days from the day of reshipment to the Buyer.
This warranty is in lieu of all other warranties expressed or implied, including without
limitation, any implied warranty or merchantability or fitness for any particular purpose, all of
which are expressly disclaimed.
1.
Proof of sale may be required in order to claim warranty.
2.
Customers outside the US are responsible for shipping charges to and from Gefen.
3.
Copper cables are limited to a 30 day warranty and cables must be in their original
condition.
The information in this manual has been carefully checked and is believed to be accurate.
However, Gefen assumes no responsibility for any inaccuracies that may be contained
in this manual. In no event will Gefen be liable for direct, indirect, special, incidental, or
consequential damages resulting from any defect or omission in this manual, even if
advised of the possibility of such damages. The technical information contained herein
regarding the features and specifications is subject to change without notice.
For the latest warranty coverage information, refer to the Warranty and Return Policy under
the Support section of the Gefen Web site at www.gefen.com.
iii
Contacting Gefen Technical Support
Technical Support
(707) 283-5900
(800) 472-5555
8:00 AM to 5:00 PM Monday - Friday, Pacific Time
Email
support@gefen.com
Web
http://www.gefen.com
Mailing Address
Gefen
Core Brands, LLC
c/o Customer Service
1800 S McDowell Blvd
Petaluma, CA 94954 USA
Product Registration
Register your product here: http://www.gefen.com/kvm/Registry/Registration.jsp
iv
Operating Notes
•
This product operates with SC-terminated single strand OM3 or OM4 (50/125 μm)
multimode fiber optic cable. Single mode fiber is not supported.
4K 600 MHz DisplayPort 1.2 Extender over one SC-Terminated Fiber Optic Cable is a trademark of Core Brands,
LLC.
© 2017 Core Brands, LLC. All Rights Reserved. All trademarks are the property of their respective owners.
Core Brands, LLC reserves the right to make changes in the hardware, packaging, and any accompanying documentation
without prior written notice.
Pb
This product uses UL or CE listed power supplies.
v
Features and Packing List
Features*
•
Supports Full-Bandwidth 4K 60 Hz 4:4:4 (600 MHz)
•
Fully compliant with DisplayPort 1.2 standard
•
Supports WQUXGA (4K; 3840x2400), 4K Ultra HD (3840 x 2160), and
•
4K Cinema - DCI (4096 x 2160) at 60Hz, 4:4:4
•
Extension up to 200m (660 feet) over one (1) SC-terminated multi-mode
•
OM3 or better (50/125um) fiber-optic cable
•
HDCP 2.2, HDCP 1.4, and DPCP compliant
•
Supports DisplayPort Auxiliary/l²C channel
•
Supports DisplayPort Multi-stream technology
•
Compact enclosures are easy to install and can be hidden away.
•
Sturdy metal construction of the enclosures help provide further immunity against
•
Electro-Magnetic Interference (EMI) and radiated noise (RFI).
•
Plug & Play – no configuration or set-up required for most applications
•
EQ switches on Sender & Receiver ensure compatibility with most sources & displays
•
Medical Safety (EN 60601-1) & EMC Compliant (EN 60601-1-2) when used with two
EXT-PS52AU-M-1.3-6-AL power supplies (available separately)
*Features and specifications are subject to change without notice. All trademarks and registered trademarks are
properties of their respective owners. Copyright© 2017 Core Brands, LLC
Packing List
The following items are shipped with the 4K 600 MHz DisplayPort 1.2 Extender over one
SC-Terminated Fiber Optic Cable. If any of these items are not present in the box when
you first open it, immediately contact your dealer or Gefen.
•
•
•
•
•
•
1 x EXT-DP-4K600-1SC-TX - Sender unit
1 x EXT-DP-4K600-1SC-RX - Receiver unit
2 x DisplayPort Male-to-Male cables, 6 feet
2 x USB-to-DC cables, 2.3 feet
2 x EXT-PS52AIP-1.3-6-AL power supplies and 2 sets of regional AC plugs (US, UK,
EU, and AU)
1 x Quick Start Guide
vi
This page left intentionally blank.
Table of Contents
1
Getting Started
Introduction............................................................................................................ 2
Sender Unit.................................................................................................... 2
Receiver Unit.................................................................................................. 4
Installation.............................................................................................................. 6
Connection Instructions.................................................................................. 6
EQ Switch Configuration................................................................................ 6
Sample Wiring Diagram................................................................................. 7
2
Appendix
Specifications....................................................................................................... 10
Index.....................................................................................................................11
viii
This page left intentionally blank.
This page left intentionally blank.
4K 600 MHz DisplayPort 1.2 Extender
over one SC-Terminated Fiber-Optic Cable
1
Getting Started
Introduction
Getting Started
Sender Unit
1
2
5V DC
Link
EXT-DP-4K600-1SC-TX
5V DC
Link
Off DE
Link
EQ
Input
EXT-DP-4K600-1SC-TX
Off DE
EQ
Input
Link
®
4K 600 MHz
®
DisplayPort Extender
over one Fiber
Sender
4K 600 MHz
DisplayPort Extender
over one Fiber
Sender
5V DC
Link
3
4
5
EXT-DP-4K600-1SC-TX
Off DE
Link
Input
EQ
page | 2
®
Getting Started
Introduction
ID
Name
Description
1
Link
Connect an SC-terminated multimode fiber
optic cable from this connector to the Fiber
connector on the Receiver unit.
2
5V DC
Connect the included 5V DC power supply or
USB to DC cable to this power receptacle.
3
Link
Under normal operating conditions, this
LED indicator will glow bright green.
4
Input
Use the included DisplayPort cable to
connect to a DisplayPort 1.2 source.
5
Off / DE
De-emphasis switch. By default this is
set to the “Off” position. See EQ Switch
Configuration (page 6) for more
information.
page | 3
Introduction
Getting Started
Receiver Unit
1
2
5V DC
Link
EXT-DP-4K600-1SC-RX
5V DC
Link
Off PE
Link
EQ
Output
EXT-DP-4K600-1SC-RX
Off PE
Output
Link
EQ
®
4K 600 MHz
®
DisplayPort Extender
over one Fiber
Receiver
4K 600 MHz
DisplayPort Extender
over one Fiber
Receiver
5V DC
Link
4
5
7
EXT-DP-4K600-1SC-RX
Off PE
Link
Output
EQ
page | 4
®
Getting Started
Introduction
ID
Name
Description
1
Link
Connect an SC-terminated multimode fiber
optic cable from this connector to the Fiber
connector on the Receiver unit.
2
5V DC
Connect the included 5V DC power supply or
USB to DC cable to this power receptacle.
3
Link
Under normal operating conditions, this
LED indicator will glow bright green.
4
Input
Use the included DisplayPort cable to
connect to a DisplayPort 1.2 display.
5
Off / PE
Pre-emphasis switch. By default this is
set to the “Off” position. See EQ Switch
Configuration (page 6) for more
information.
page | 5
Getting Started
Installation
Connection Instructions
►► Video
1.
Connect the included DisplayPort cable between the DisplayPort 1.2 source and the
Input port on the Sender unit.
2.
Connect a DisplayPort 1.2 display to the Output port on the Receiver unit, using the
included DisplayPort cable.
►► Fiber
3.
Connect a single SC-terminated OM3 or OM4 (50/125 μm) multimode fiber optic
cable, up to 660 feet (200 meters), between the Link port on the Sender unit and the
Link port on the Receiver unit.
►► Power
4.
Connect the included 5V DC power supplies to the 5V DC port on both the Sender
and Receiver unit.
5.
Connect the opposite end of the power supplies to available electrical outlets.
6.
The Link indicators on both units will light once all connections are complete and the
units, the source, and the display are powered up.
Link
EQ 5V
Switch
Configuration
DC
Sender unit - By default, this switch is in the “Off” position. Set the switch to the “DE”
(signal de-emphasis) setting, if the source output is very high.
EXT-DP-4K600-1SC-TX
Off DE
Input
Link
EQ
5V DC
Link
Receiver unit - By default, this switch is set to the “Off” position . Set to the “PE”
(signal pre-emphasis) position if the sink device requires a higher than normal input level.
EXT-DP-4K600-1SC-RX
Off PE
Link
Output
®
EQ
4K 600 MHz
DisplayPort
page | 6 Extender
over one Fiber
Sender
Getting Started
Sample Wiring Diagram
DISPLAYPORT CABLE
FIBER OPTIC (SC-SC) CABLE
4K 600 MHz DisplayPort 1.2
Source
4K 600 MHz DisplayPort 1.2
Extender
(Sender unit)
®
is
D
z
H
M r
0 e
60 tend
4K Ex
ort
yP
pla
ove
r one
Sen Fibe
der r
5V
4K 600 MHz DisplayPort 1.2
Extender
(Receiver unit)
DC
Link
®
is
D
z
H
M r
0 e
60 tend
4K Ex
ort
yP
pla
ove
r one
Rec Fibe
eiv
er r
-RX
-1SC
Off
PE
K600
DP-4
EQ
EXT-
ut
Outp
Link
4K 600 MHz DisplayPort 1.2
Display
EXT-DP-4K600-1SC
page | 7
4K 600 MHz DisplayPort 1.2 Extender
over one SC-Terminated Fiber-Optic Cable
2
Appendix
Appendix
Specifications
Supported Formats
Video
•
•
•
•
3840 x 2160 @ 60 Hz
WQUXGA (4K; 3840x2400 @ 60Hz)
4K Ultra HD (3840 x 2160 @ 60Hz)
4K Cinema - DCI (4096 x 2160 60Hz)
Input (Sender)
•
1 x DisplayPort, 20-pin, female
Output (Receiver)
•
1 x DisplayPort, 20-pin, female
Link (Sender / Receiver)
•
1 x SC-type, female
Link (Sender / Receiver)
•
1 x LED, green
Power
•
1 x 1.3 mm barrel jack
Video Bandwidth
•
21.6 Gbps (5.4 Gbps per lane, 4 lanes)
Optical Wavelength
•
850 nm
Power Input
•
5V DC
Power Consumption (Sender)
•
1.75 W
Power Consumption (Receiver)
•
2.0 W
Optical Power Budget
•
6.5 dB
Operating Temperature
•
+32 to +122 ºF (0 to +50 ºC)
Operating Humidity
•
10% to 85% RH, non-condensing
Storage Temperature
•
-4 to +158 °F (-20 to +70 °C)
Storage Humidity (RH)
•
10% to 85% RH, non-condensing
Dimensions (W x H x D)
(Sender / Receiver),
not including connectors
•
1-3/4” x 7/8” x 3-1/8” (45 mm x 22 mm x
79 mm)
Unit Weight (each)
•
4.8 oz. (0.135 kg)
Shipping Weight
•
2.5 lbs (1.2 kg)
Connectors & Indicators
Operational
Physical
NOTE: Features and specifications are subject to change without notice. All trademarks and registered trademarks are
properties of their respective owners. Copyright© 2017 Core Brands, LLC
page | 10
Appendix
Index
C
T
Configuration
EQ switch 6
Connection Instructions 6
D
Table of Contents viii
Technical Support iv
W
Warranty Information iii
Wiring Diagram 7
De-emphasis
EQ switch 3
DisplayPort
port 3, 5
E
EQ
Off / DE 3
Off / PE 5
F
Features vi
I
Installation 6
L
Link
LED 3, 5
port 3, 5
O
Off / DE
switch 3
Operating Notes v
P
Packing List vi
Power
port 3, 5
Pre-emphasis
EQ switch 5
S
Safety Instructions ii
Sender Unit 2
Specifications 10
page | 11
*Preferred
Stretch it. Switch it. Split it. Gefen’s got it. ®
180020600
S McDowell
Nordhoff
Blvd.St.,Petaluma
Chatsworth
CA CA
94954,
91311 USA
(707)
283-5900
(800)
472-5555
1-800-545-6900 818-772-9100 fax: 818-772-9120
www.gefen.com support@gefen.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising