Hannspree | HS 225 HFB | User manual | Hannspree HS 225 HFB User manual

Hannspree HS 225 HFB User manual
HS225HFB (HSG1394)
LCD Monitor
OSD[V6.0]
User’s Manual
OSD[V6.1]
Before operating the monitor, please read this manual thoroughly. This manual should be retained for
future reference.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
ƒ
Reorient or relocate the receiving antenna.
ƒ
Increase the separation between the equipment and receiver.
ƒ
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
ƒ
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Parts 15 of the FCC Rule. Operation is subject to the following two
conditions﹕(1) this device may not cause harmful interference﹔and (2) this device must accept any
interference received, including interference that may cause undesired operations.
CANADA
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
【Optional, depend on selected model】
This device complies with requirement of EMC directive 2014/30/EU with regard to
Electromagnetic Compatibility, and 2014/35/EU and 93/68/EEC with regard to Low Voltage
directive.
【Optional, depend on selected model】
Socket-outlet shall be near the equipment and shall be accessible.
Trademark Notice:
HANNSpree products incorporate High-Definition Multimedia Interface
(HDMI TM) technology.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
2
User’s Manual
RECYCLING INFORMATION
We, at HANNspree care very much about our environment protection strategy and firmly believe
that it helps us have healthier earth via appropriate treatment and recycling of industrial technology
devices at the end-of-life.
These devices contain recyclable materials, which can be re-decomposed and re-integrated into
brand-new marvels. On the contrary, other material can be classified to hazardous and poisoned
substances. We strongly encourage you to contact the provided information to recycle this product.
For more information, please visit
http://www.hannspree.eu/
3
User’s Manual
TABLE OF CONTENTS
SAFETY NOTICE .................................................................................................. 5
PRECAUTIONS................................................................................................. 5
SPECIAL NOTES ON LCD MONITORS ...................................................... 6
BEFORE YOU OPERATE THE MONITOR ...................................................... 7
FEATURES......................................................................................................... 7
CHECKING THE CONTENTS OF THE PACKAGE .................................. 7
INSTALLATION INSTRUCTIONS ................................................................ 8
POWER............................................................................................................... 8
MAKING CONNECTIONS.............................................................................. 9
ADJUSTING THE VIEWING ANGLE......................................................... 10
OPERATING INSTRUCTIONS ..........................................................................11
GENERAL INSTRUCTIONS..........................................................................11
FRONT PANEL CONTROL .......................................................................... 12
HOW TO ADJUST A SETTINGS .................................................................. 13
PLUG AND PLAY............................................................................................ 15
TECHNICAL SUPPORT (FAQ) ......................................................................... 16
Q & A FOR GENERAL PROBLEMS ........................................................... 16
ERROR MESSAGE & POSSIBLE SOLUTIONS ....................................... 18
APPENDIX ............................................................................................................ 20
SPECIFICATIONS .......................................................................................... 20
4
User’s Manual
SAFETY NOTICE
1. The changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the
emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to correct such interference.
4. Only use attachments/accesories specified by the manufacturer.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously high
voltages are present inside the monitor. Do not open the cabinet. Refer servicing to qualified
personnel only.
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub,
swimming pool or in a wet basement.
• Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a
person and cause serious damage to the appliance. Use only a cart or stand recommended by the
manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting kit approved by the manufacturer and follow the kit instructions.
• Slots and openings in the back and bottom of the cabinet are provided for ventilation. To
ensure reliable operation of the monitor and to protect it from overheating, be sure these
openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar
surface. Do not place the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
• The monitor should be operated only from the type of power source indicated on the label. If
you are not sure of the type of power supplied to your home, consult your dealer or local power
company.
•
Unplug the unit during a lighting storm or when it will not be used for long period of time. This
will protect the monitor from damage due to power surges.
•
Do not overload power strips and extension cords. Overloading can result in fire or electric
shock.
•
Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a
fire or electric shock. Never spill liquids on the monitor.
•
Do not attempt to service the monitor by yourself; opening or removing covers can expose you
to dangerous voltages and other hazards. Please refer all servicing to qualified service
personnel.
•
The wall socket shall be installed near the equipment and shall be easily accessible.
•
5
User’s Manual
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
z
z
z
z
z
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the
Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern you
use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01% or
less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an afterimage of the previous screen may remain after
switching the image, when the same image is displayed for hours. In this case, the screen is
recovered slowly by changing the image or turning off the Power Switch for hours.
If the screen suddenly flashes erratically or the backlighting fails, please contact your dealer or
service center for repair. Do not attempt to repair the monitor yourself.
6
User’s Manual
BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
54,6cm / 21.5” Wide Screen TFT Color LCD Monitor
Crisp, Clear Display for Windows
GP Green Product
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Screen
Base
Cables and User manual
Power Adaptor
HDMI Cable
Warranty Card
EUR Energy Label
7
Quick Start Guide
User’s Manual
INSTALLATION INSTRUCTIONS
Figure.1. Installing and Removing the Base
INSTALLATION:
1.
2.
3.
4.
5.
Put the monitor on the flat or soft place.
Remove the screws on the bracket.
Align the monitor with the opening in the base.
Align the screw to the hole position on the base and lock it clockwise.
Verify that the monitor is securely attached to the base by looking at the bottom of the base and
making sure that the clips are fully engaged in the base.
REMOVAL:
1. Flip over the monitor so that it is upside down.
2. Remove the screws counterclockwise and separate the base.
3. Gently pull the base from the monitor until they are unattached.
POWER
POWER SOURCE:
1. Plug one end of the 12V DC adapter to the LCD monitor’s DC 12V input socket, plug one end of
the AC power cord to the 12V DC adapter AC input socket, and the other end of the AC power
cord to Wall outlet.
2. Connect the DC-power adaptor one end to your LCD monitor’s DC-input port, the other end to
wall-outlet.
8
User’s Manual
MAKING CONNECTIONS
CONNECTING TO A PC
Turn off your computer before performing the procedure below.
1. Connect one end of the VGA cable (optional) to the back of the monitor and connect the other
end to the computer’s VGA port.
2. Connect one end of the HDMI to DVI cable (optional) to the back of the monitor and connect the
other end to the computer’s DVI port.
3. Connect one end of the HDMI cable to the back of the monitor and connect the other end to the
computer’s HDMI port.
4. Connect the audio cable between the monitor's audio input and the PC's audio output (green port).
5. Plug one end of the DC power adaptor to the LCD monitor’s DC input port, and the other end to
Wall outlet.
6. Turn on your monitor and computer.
Figure.2. Connecting to a PC
1
3
Power DC Input
VGA Input
2
4
9
Earphone out
HDMI Input
User’s Manual
ADJUSTING THE VIEWING ANGLE
• For optimal viewing it is recommended to look at the full face of the monitor, then adjust the
monitor’s angle to your own preference.
• Hold the stand so you do not topple the monitor when you change the monitor’s angle.
• You are able to adjust the monitor’s angle from -5° to 15°.
Figure.3. Monitor Angle
NOTES:
• Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD
screen.
• Be careful not to place fingers or hands near the hinges when tilting the monitor, otherwise
pinching can result.
10
User’s Manual
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located on the
front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to
your personal preferences.
• The power adaptor should be connected.
• Connect the Signal cable from the monitor to the HDMI card.
• Press the power button to turn on the monitor. The power indicator will light up.
Return /Auto adjustment《Analog Input Models》
+
﹣
Menu / Enter
Power Button
Figure.4. Control Panel Buttons
11
User’s Manual
FRONT PANEL CONTROL
• Power Button:
Press this button to switch ON/OFF of monitor’s power.
• Power Indicator:
White — Power On mode.
White flicker — Power Saving mode.
• MENU / ENTER:
1. Turn the OSD menu on/off.
2. The OSD menu is used as <<confirmation>> function during start-up
• Adjust▼▲:
Navigate through adjustment icons when OSD is ON or adjust a function when function is
activated.
】Button: 《Analog Input Models》
1. The 「Auto adjustment」 function works only for VGA input. (The auto adjustment function is
used to optimize the 「horizontal position」, 「vertical position」,「clock」,and 「phase」.)
2. Return to the previous menu.
•【
NOTES:
• Do not install the monitor in a location near heat sources such as radiators or air dusts, or in a
place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
• Save the original shipping box and packing materials, as they will come in handy if you ever have
to ship your monitor.
• For maximum protection, repackage your monitor as it was originally packed at the factory.
• To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be
removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents
such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety
precaution, always unplug the monitor before cleaning it.
12
User’s Manual
HOW TO ADJUST A SETTINGS
BRIGHTNESS
BRIGHTNESS
CONTRAST
PRESET MODE
ACTIVE
CONTRAST
OVERDRIVE
Adjust the brightness value of the display according to your preference.
Select「BRIGHTNESS」option to adjust the brightness value.
Adjust the contrast value of the display according to your preference.
Select「CONTRAST」option to adjust the contrast value.
Select the preset mode according to your preference: PC/ MOVIE/ GAME/
ECO
[The availability of this function depends upon the selected model]
Optimal setting for high contrast images or videos. The dark and light areas
of the image are automatically detected, and the contrast is enhanced to
provide a clearer, sharper image. Also, you may select the「ACTIVE
CONTRAST」option.
Setup the display response time through the Response time function.
Available settings are ON, and OFF. [This feature is limited to specific
models only.]
IMAGE SETUP
H-POSITION
Select the 「H-POSITION」option to shift the screen image to the left or
right. Enter the option and adjust the level. [For VGA only]
V-POSITION
Select the 「V-POSITION」option to shift the screen image up or down.
Enter the option and adjust the level. [For VGA only]
CLOCK
Select the 「CLOCK」option to reduce the vertical flicker of characters on
the screen. Enter the option and adjust the level. [For VGA only]
PHASE
IMAGE RATIO
COLOR SETUP
5500K
6500K
9300K
Low Blue Mode
USER
Select the「PHASE」option to reduce the horizontal flicker of characters on
the screen. Enter the option and adjust the level. [For VGA only]
When the aspect ratio of screen is distorted, you may make adjustments by
using this function.「WIDE」indicates full screen display, which does not
ensure the image is shown as is or in initial scale. 「4:3」indicates scaling
by the proportion of original images, which may cause the screen showing
black bands. [The availability of this function depends upon the selected
model]
Adjust the color temperature value of the display according to your
preference: 5500 /6500/ 9300 / Low Blue Mode.
Move the cursor to the User option and select it,
1. To adjust the red, enter the「R」option and adjust the level.
2. To adjust the green, enter the「G」option and adjust the level.
3. To adjust the blue, enter the「B」option and adjust the level.
13
User’s Manual
LOW BLUE MODE
Move the cursor to the Low Blue Mode option and select it.
OSD SETUP
LANGUAGE
H-POSITION
V-POSITION
TIME OUT
TRANSPARENCY
Select「LANGUAGE」option to change the language of the OSD. Enter the
option and select a language. [Reference only, the OSD Language depends
on the selected model]
Select 「H-POSITION」option to adjust the horizontal position of the OSD.
Enter the option and adjust the level.
Select 「V-POSITION」option to adjust the vertical position of the OSD.
Enter the option and adjust the level.
Select 「TIMEOUT」option to set the OSD time out from 5 to 120 seconds.
Enter the option and adjust the level.
Select 「TRANSPARENCY」option to adjust the transparency of the OSD.
Enter the option and adjust the level(0,25,50,75,100).
RESET
AUTO CONFIG
AUTO COLOR
RESET
The auto config function is used to optimize the 「H-POSITION」,
「V-POSITION」,「CLOCK」,and 「PHASE」. [For VGA Input only]
The auto color function is used to optimize the 「COLOR」. [For VGA
Input only]
Select the 「RESET」option to reset to the monitor’s default setting. This
will erase the current settings. Enter the option and select On or Off.
EXTRA
INPUT SELECT
MUTE
VOLUME
DDC/CI
The input select function is to enter Source selections. (Selections include
VGA, HDMI, etc. The actual selections may vary depending on the models.
This function is only available in models with digital inputs)
Select the「MUTE」option to switch the function On or Off. [The
availability of this function depends upon the selected model. Adjusting the
volume while muted cancels Mute mode.]
Select the 「VOLUME」option to change the volume level. Enter the option
and adjust the level. [This function applies only to models with
incorporated audio.]
● By high volume, risk of hearing damage exists.
Select the 「DDC/CI」option to switch the function On or Off. [Dual input
mode optional]
14
User’s Manual
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD.
It allows the monitor to inform the host system of its identity and, depending on the level of DDC
used, communicate additional information about its display capabilities. The DDC2B is a
bidirectional data channel based on the I²C protocol. The host can request EDID information over the
DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
15
User’s Manual
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL PROBLEMS
PROBLEM & QUESTION
POSSIBLE SOLUTION
Power LED is not on
*Check if the Power Switch is in the ON position.
*Power Adaptor should be connected.
No Plug & Play
*Check if the PC system is Plug & Play compatible.
*Check if the Video Card is Plug & Play compatible.
*Check if any plug pins on the VGA or HDMI
connector is bent.
The display is too dark or too bright.
*Adjust the Contrast and Brightness Controls.
Picture bounces or a wave pattern is
present in the picture
*Move electrical devices that may cause electrical
interference.
*Computer Power Switch should be in the ON
position.
*Computer Video Card should be snugly seated in its
slot.
*Make sure monitor’s video cable is properly
The power LED is ON (White Flicker) but connected to the computer.
there’s no video or no picture.
*Inspect monitor’s video cable and make sure none
of the pins are bent.
*Make sure computer is operational by hitting the
CAPS LOCK key on the keyboard while observing
the CAPS LOCK LED. The LED should either turn
ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED,
GREEN, or BLUE)
*Inspect the monitor’s video cable and make sure that
none of the pins are bent.
Screen image is not centered or sized
properly.
* Adjust pixel frequency CLOCK and PHASE.
Picture has color defects
(White does not look white)
*Adjust RGB color or select color temperature.
The screen resolution needs to be adjusted
*Use win 2000/ME/XP Right click anywhere on
desktop and select Properties>Settings>Screen
Resolution. Use the silder to adjust the reslution
and click Apply.
16
User’s Manual
Addendum related to Windows 7 / Windows 8
When you encounter display problem under Windows 7/ Windows 8, you need to do the following:
1. Make sure your PC computer (Hardware requirement) can support Windows 7/ Windows 8.
2. Make sure your video card can run Windows 7/ Windows 8.
3. If your video card can support Windows 7/ Windows 8, need to install the latest Windows 7/
Windows 8 driver of your video card.
Suggest to do the following:
1. Install the latest Windows 7/ Windows 8 video driver of your video card.
2. Try to use the recommended display resolution that is supported by the monitor.
3. If the recommended display resolution is not working, try the second recommended display
resolution.
35,56cm / 14” (16:9)
39,6cm / 15.6” (16:9)
40,64cm / 16” (16:9)
43,2cm / 17” (16:10)
47cm / 18.5” (16:9)
48,3cm / 19” (5:4)
48,3cm / 19” (16:10)
51cm / 20” (16:9)
56cm / 22” (16:10)
54,6cm / 21.5” (16:9)
58,4cm / 23” (16:9)
60cm / 23.6” (16:9)
62,5cm / 24.6 (16:9)
68,6cm / 27 ” (16:9)
70cm / 27.5” (16:10)
1
1366×768@60Hz
1366×768@60Hz
1366×768@60Hz
1440×900@60Hz
1366×768@60Hz
1280×1024@60Hz
1440×900@60Hz
1600×900@60Hz
1680×1050@60Hz
2
1366×768@50Hz
1366×768@75Hz
1366×768@50Hz
1440×900@75Hz
1366×768@75Hz
1280×1024@75Hz
1440×900@75Hz
1600×900@50Hz
1680×1050@50Hz
1920×1080@60Hz
1920×1080@50Hz
1920×1200@60Hz
1920×1200@50Hz
And if you still have display problem after doing the above procedure, please visit Hannspree
support and Service Website: http://www.hannspree.eu/en/monitors
Windows is a registered trademark of Microsoft Corporation.
17
User’s Manual
ERROR MESSAGE & POSSIBLE SOLUTIONS
ƒ
CABLE NOT CONNECTED:
1. Check that the signal-cable is properly connected, if the connector is loose, tighten the
connector’s screws.
2. Check the signal-cable’s connection pins for damage.
ƒ
INPUT NOT SUPPORT :
Your computer has been set to unsuitable display mode, set the computer to display mode given
in the following table.
FACTORY PRESET TIMING TABLE:
MODE
RESOLUTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
640×480 @60Hz
640×480 @70Hz
640×480 @67Hz
640×480 @72Hz
640×480 @75Hz
720×400 @70Hz
800×600 @56Hz
800×600 @60Hz
800×600 @72Hz
800×600 @75Hz
832×624 @75Hz
1024×768 @60Hz
1024×768 @70Hz
1024×768 @75Hz
1152×870 @75Hz
1152×864 @75Hz
1280×720 @60Hz
1280×960 @60Hz
1280×960 @75Hz
1280×768 @60Hz
1280×768 @75Hz
1280×1024 @60Hz
1280×1024 @75Hz
1360×768 @60Hz
1366×768 @60Hz
1440×900 @60Hz
1440×900 @75Hz
1400×1050 @60Hz
HORIZONTAL
FREQUENCY (KHz)
31.469
36.052
35.000
37.861
37.500
31.469
35.156
37.879
48.077
46.875
49.725
48.363
56.476
60.023
68.681
67.500
45.000
60.000
74.592
47.776
60.289
63.981
79.976
47.712
47.852
55.469
70.635
64.744
18
VERTICAL
FREQUENCY (Hz)
59.940
70.004
66.667
72.809
75.000
70.087
56.250
60.317
72.188
75.000
75.000
60.004
70.069
75.029
75.062
75.000
60.000
60.000
74.443
59.870
74.893
60.020
75.025
60.015
59.964
59.901
74.984
59.948
User’s Manual
29
30
31
1600×900 @60Hz
1680×1050 @60Hz
1920×1080 @60Hz
55.540
65.290
67.500
59.978
59.954
60.000
(Video mode)
MODE
RESOLUTION
1
640×480p @60Hz
2
720×480i @60Hz
3
720×480p @60Hz
4
720×576i @50Hz
5
720×576p @50Hz
6
1280×720p @60Hz
7
1920×1080i @50Hz
8
1920×1080i @60Hz
9
1920×1080p @50Hz
10
1920×1080p @60Hz
** We ensure that the monitor can be lighted under interlace signal mode, but we can not guarantee
the image quality.
19
User’s Manual
APPENDIX
SPECIFICATIONS
LCD Panel
Video
Driving system
TFT Color LCD
Size
54,6cm / 21.5” Diagonal
Pixel pitch
0.24795mm(H) × 0.24795mm(V)
H-Frequency
30KHz – 83KHz
V-Frequency
50Hz – 75Hz
Display Colors
16.7M Colors
Max. Resolution
1920 × 1080 @60Hz
Plug & Play
VESA DDC2BTM
Power consumption
ON Mode
26 W (Typical)
Power Saving Mode
≤0.5 W
OFF Mode
≤0.3 W
Audio output
Rated Power 2.0 W rms (Per channel)
Input Terminal
HDMI
VGA
Maximum Screen Size
Hor. : 476.064mm
Ver. : 267.786mm
Power Source
AC Power: 100–240V ~0.75A 50–60Hz
DC Adaptor: 12V, 2.5A
Environmental
Considerations
Operating Temp:5° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10% to 90%
Dimensions
493.82 (W)×359.79(H)×134.28(D) mm
19.8 ”(W)×14.2 ”(H)×5.3 ”(D)
Weight (NW)
2.5 kg
*** The above specification is subject to actual product specification and is subject to change
without prior notice.
NOTES:
The Maximum Resolution will depends on the display card supporting. Related issue can refer to
http://www.hannspree.eu/en/monitors. FAQ section.
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising