Ikelite | 200DLM/A Underwater TTL Housing for Canon EOS M50, Kiss M Mirrorless Digital Cameras | Instruction manual | Ikelite 200DLM/A Underwater TTL Housing for Canon EOS M50, Kiss M Mirrorless Digital Cameras Instruction Manual

Ikelite 200DLM/A Underwater TTL Housing for Canon EOS M50, Kiss M Mirrorless Digital Cameras Instruction Manual
200DLM/A Underwater Housing for Canon EOS M50,
EOS Kiss M
Product Number 6973.15
Product Registration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to contact you
in the event of a product update.
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product
to receive information on any updates or notices pertaining to your
equipment.
Included in the Box
• Housing
• Housing Rear O-Ring # 0110 (installed)
• Housing Front Port Base to Port O-Ring # 0132.36 (installed)
• Waterproof bulkhead cap # 9104.7 (installed)
• 1/16” Hex Key # 0945.16
• Silicone Lubricant
Specifications
• 200 ft (60m) depth rating
• DLM Type A port mount
• Controls for all important camera functions. A control is not provided
for the WiFi button.
• Ikelite flash bulkhead connector with built-in TTL circuitry
• Slightly negative buoyancy in fresh water (varies with port choice)
• Weight 2.7 lb (1.2 kg) not including port
• Dimensions 7.5 x 5.8 x 5.4” (191 x 147 x 137 mm)
• ABS-PC, acrylic, and acetyl construction
2
Important Notices
»» This housing requires a compatible Lens Port for waterproof
operation. The housing is not waterproof without a Lens Port
attached.
»» A bulkhead cap or sync cord must be attached to the housing
for waterproof operation. Never submerge the housing without
either a sync cord or waterproof bulkhead cap attached.
»» To prevent salt build-up and sticking controls, turn the camera
off and submerge the sealed housing in clean, freshwater.
Operate the controls several times each while underwater to
flush out any residue.
»» Never leave a housing in a rinse tank, even if it is the only
system in the tank. Most catastrophic floods happen when the
user walks away from a housing while it is in the rinse tank.
»» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
»» This housing is only compatible with the Canon EOS M50
and EOS Kiss M as shipped by the manufacturer. Unless
otherwise noted, this housing does not accommodate the use
of add-on grips, battery grips, eyepieces, LCD covers, or other
accessories.
»» Do not remove the Accessory Port Hole Plug unless you are
installing a compatible accessory such as factory optional
Vacuum Kit # 47012.
3
Contents
Product Registration
1
About this Product
2
Included in the Box
2
Specifications
2
Important Notices
3
Getting to Know Your Housing
5
Setting Up Your Camera
6
Setting Up Your Housing
7
Pre-Installation Checklist & Initial Camera Settings 6
Opening the Housing 7
Inserting the Camera 7
Attaching the Hotshoe 8
Closing the Housing 9
Attaching the Lens Port 10
Final Check 11
Entering the Water 11
Setting Up An External Strobe
12
Installing an Accessory via the Accessory Port
14
Maintenance
15
Troubleshooting
16
Spare Parts / Optional Accessories
18
Limited Warranty
18
Service and Repairs
19
Contact Us
20
About the Built-In Flash 12
About Sync Cords 12
Attaching a Sync Cord 13
Accessory Port 14
Post-Dive 15
Travel and Storage 15
4
Getting to Know Your Housing
Main Dial
Movie Button
Multi-Function Button
Power Switch
Electrical
Bulkhead
Shutter
Button
Lens Port
Mount
Lid
Snap
Lens
Release
Button
Tray Mounts
Accessory Port
Hole Plug
Super-eye Viewfinder
Mode
Dial
INFO
MF
Q-SET
MENU
O-ring
Camera
Mounting Plate
Mounting Plate
Base
5
Setting Up Your Camera
Pre-Installation Checklist & Initial Camera Settings
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Set Mode Dial to “M” Manual Mode. Set aperture to f/8 and
shutter speed to 1/125th second. Other shooting modes are not
recommended.
4. Set Image Review to “4 or 8 sec.”
5. In Flash Control: Set Flash Firing to
“Fire” when using a strobe.
Set E-TTL II meter to “Evaluative.” Set Red-eye reduc. to “Disable.”
Set external flash settings as desired once a strobe is detected and
turned on.
6. Set ISO speed to “200.” When NOT using a strobe, set ISO to
“Auto.”
7. Set Metering to
“Center-weighted”.
8. Set White Balance to “AWB.”
9. Set AF operation to “ONE SHOT” and AF method to “1-point AF.”
10. Set AF-assist beam firing to “OFF.”
11. Set Eco Mode to “Off.”
12. Set Touch Control to “Disable.”
13. In Power Saving: Set Display Off to “3 min.” and Auto Power Off to
“5 min.”
NOTE: These are recommended “initial” camera settings to get
you started. Please adjust your camera as needed for each unique
shooting situation. Settings not mentioned should be set to the
user’s preference.
6
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep firm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snap(s).
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap which may be attached to the
camera.
2. Check to see whether the camera’s lens will fit through the port
opening of the housing. If not, the lens will need to be removed
from the camera body and reattached AFTER the camera body is
installed in the housing.
3. Remove the Camera Mounting Plate from the housing.
7
4. Line up the Mounting Screw with the Camera Tripod Socket. Use
a coin or flat head screwdriver (preferred) to tighten the mounting
plate to the camera.
1/4-20 Mounting Screw
Camera Tripod Socket
1/4-20 Threaded Hole
Camera Mounting Plate
5. Pull out on the housing control knobs to move the controls out of
the way.
6. Insert the Camera Mounting Plate into the slot of the Mounting
Plate Base. Push the camera all of the way forward until the back of
the Mounting Plate is flush with the Housing Plate Base, page 5.
Attaching the Hotshoe
1. Make sure the Hotshoe and camera contacts are clean.
8
2. Slide the Hotshoe onto the camera Hotshoe Mount.
Hotshoe
Hotshoe Mount
3. Push the Hotshoe forward until it is unable to go any farther. The
Hotshoe must be pushed all the way forward to make proper
contact with the camera and provide TTL operation. Make sure
the Hotshoe wire does not interfere with any housing control
operations.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The main o-ring does not require lubricant to make
a seal.
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
5. Push the lid snaps towards the housing until they are flat against
the housing and the lock has engaged. Close opposing lid snaps at
the same time.
9
6. Check the o-ring seal. The o-ring should form a uniform, solid line
around the back of the housing. There will be a small, even gap
around the housing between the housing back and the housing
front.
Attaching the Lens Port
A compatible lens port is required for waterproof operation.
Never submerge the housing without a lens port attached.
1. Lightly lubricate the o-ring on the Port Base. When properly
lubricated, the o-ring should have an even, slightly shiny
appearance. Wipe off any excess lubricant. Lubricant prevents the
o-ring from rolling or extruding; it is not a sealing mechanism.
2. If using an optional Gear Sleeve, place it in the Port Base with the
teeth side facing away from the housing.
Lens Port
Optional
Gear
Sleeve
O-ring
10
Port Base
3. If using an optional Gear Sleeve, place it in the Port Base with the
teeth side facing away from the housing.
4. Slide the Lens Port onto the housing Port Base and press evenly
down towards the housing until it stops. There should be a very
thin, even gap between the bottom of the port and the housing
front.
5. If using a dome with a shade, rotate the lens port gently so that the
wider extensions are oriented on the top and bottom. If the shade is
not aligned properly, it may cause vignetting (dark shadows in the
corner of the image).
Final Check
1. Re-check the o-ring seal. The seal should form an even, solid line
around the back of the housing.
2. Turn on the camera and check all control functions.
3. Make sure that the camera can obtain focus and take a photo.
4. Check battery life and open storage space on your memory card.
5. Check the flash/strobes, if using.
6. Submerge the housing in a fresh water tank dedicated to
underwater photography equipment. Visually confirm that there are
no signs of water intrusion or a steady stream of bubbles coming
from one of the housing seals.
Entering the Water
1. If possible, we recommend entering the water without your housing
to ensure that you are comfortable and your life-saving equipment
is in working order. Once you are stable, have someone pass your
camera housing to you.
11
2. As soon as you enter the water, take a moment and check to see
that the housing is properly sealed. If possible, first water test the
housing with no camera inside to assure a safe and watertight
environment.
3. Submerge the housing at the surface of the water and visually
confirm that there are no signs of water intrusion or a steady stream
of bubbles coming from one of the housing’s seals. If water does
appear to be entering the housing, point the lens port downward
and return the housing to the surface as quickly as possible. Please
observe all necessary safety precautions. NEVER ascend faster
than accepted safety limits.
4. Use your hand to gently flush away any small bubbles that may be
on the face of the lens port. Bubbles will produce soft focus spots in
your photo or video.
Setting Up An External Strobe
About the Built-In Flash
The camera’s built-in flash CANNOT light a subject underwater due to
the housing’s opaque design and CANNOT be used to trigger a fiber
optic strobe.
We recommend attaching an external strobe via sync cord for optimal
color and clarity in a wide variety of shooting situations, including
daylight photography.
About Sync Cords
When a compatible Ikelite DS strobe is attached via sync cord,
circuitry built into the housing allows the strobe to communicate
directly with the camera to trigger the strobe and adjust its power for
perfect exposure.
12
Strobes from SEA&SEA, INON and Nikonos attached by electrical
sync cord are not capable of powering the TTL circuitry built into this
housing. These strobes must be used in manual power modes when
connected via electrical sync cord.
Attaching a Sync Cord
A bulkhead cap or sync cord must be attached to the housing for
waterproof operation. Never submerge the housing without either
a sync cord or waterproof bulkhead cap attached.
1. Remove the bulkhead cap.
2. Lightly lubricate the sync cord o-rings. We recommend using only
Ikelite silicone lubricant to eliminate the possibility of swelling due to
incompatible compounds.
3. Line up the pins and receptacles and gently insert the sync cord
plug into the housing bulkhead. DO NOT force or rush this
installation. The sync cord will not go into the bulkhead if the Pins
and Receptacles are misaligned.
Waterproof
Bulkhead Cap
Knurled
Retaining
Ring
Sync Cord
O-ring
Knurled
Retaining Ring
Sync Cord
Plug
Pins and
Receptacles
Bulkhead
4. Attach the other end of the sync cord to the bulkhead on your
strobe.
13
5. If using an Ikelite strobe, set the strobe to TTL. If using a non-Ikelite
strobe, set the strobe to manual flash and select a manual power
setting.
6. Turn on the strobe(s).
7. Turn on the camera.
8. Take a test photo to ensure that your strobe(s) are functioning
properly.
Accessory Port
Your housing features one 1/2-20 threaded Accessory Port which
may be used for attachment of factory optional or aftermarket housing
accessories. Visit ikelite.com for an updated list of factory optional
accessories.
Installing an Accessory via the Accessory Port
1. Remove the Hole Plug using an 11/16” open end wrench.
2. Check the accessory fitting o-ring sealing area. Check o-ring and
housing o-ring sealing area. All should be clean and free of hair,
sand, or other debris.
3. Lightly lubricate o-ring with Ikelite lubricant. Use ONLY Ikelite
lubricant. Other manufacturer lubricants can cause the o-ring to
swell.
4. Carefully screw in and tighten accessory fitting. The accessory port
features a 1/2-20 threaded hole. Make sure your fitting is the same
thread pattern. DO NOT cross-thread. DO NOT overtighten.
14
5. After installing an accessory, pressure test the housing by diving
without a camera inside.
NOTICE: Your Ikelite housing warranty DOES NOT extend
to cover the attachment of aftermarket housing accessories
or accessory fittings by 3rd parties. Warranty DOES cover
factory optional accessories attached by certified Ikelite service
technicians.
»» DO NOT remove the Accessory Port Hole Plug unless you are
installing a compatible accessory like Vacuum Kit # 47012.
Maintenance
Post-Dive
1. Rinse the housing in fresh water. Rotate the housing’s controls and
press each button while submerged in fresh water to flush out any
salt or debris to ensure smooth operation on future dives.
2. NEVER leave your housing in the fresh water rinse tank. Collisions
with other peoples’ gear can cause scratches or damage to your
equipment.
3. Stow the housing in a shaded place where it is protected from
impact or overheating. If no shade is available, we recommend
covering the housing with a towel or cloth.
4. Check the memory card capacity and battery life of your camera
and strobe(s). Recharge as necessary.
5. Always recheck o-ring seal after opening the housing.
Travel and Storage
1. Remove the camera from the housing for travel or storage.
15
2. Check the main housing o-ring.
3. Close the empty housing and submerge in lukewarm fresh water.
While submerged, rotate each control and depress each button to
flush out any salt or debris.
4. Remove the housing from water and rinse with running water.
5. Do not rinse the inside of the housing or submerge the open
housing in water. If the inside of the housing needs to be cleaned,
wipe with a clean, slightly damp cloth.
6. Dry the housing with a clean, lint-free cloth.
7. Store in a cool, dry place.
8. Like regulators and other pressure-sensitive equipment, we
recommend careful care and cleaning along with annual
replacement of the factory seals.
Troubleshooting
Water enters the housing
• Re-clean and re-install the main o-ring.
• Take the housing underwater without a camera installed to ensure
that the leaking has been corrected.
Photos are over-exposed (too light)
• Adjust aperture (smaller), shutter speed (faster), or ISO (lower)
setting.
• Move lights(s) farther away from your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
16
Photos are under-exposed (too dark)
• Adjust aperture (larger), shutter speed (slower), or ISO (higher)
setting.
• Move light(s) closer to your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
Strobe will not fire
• Turn on strobe and make sure it is properly charged.
• Make sure that the camera’s flash is set to fire on every photo.
• Check that the sync cord is properly attached.
Buttons are stuck
• Soak the housing in lukewarm fresh water. Depress each button
several times while the housing is submerged.
• Apply lubricant to the button. Press the button several times to
distribute the lubricant.
Button(s) or control(s) do not line up
• Ensure that nothing is preventing the camera from going into the
housing.
• Push the camera mounting plate forward until it is flush with the
mounting plate base.
• Camera should be “tight” against the mounting plate. Check
tightness using a coin or flathead screwdriver (preferred).
Camera is not functioning normally underwater
• Ensure that the camera mounting plate is pushed all of the way into
the mounting plate base.
17
• Check each housing control while underwater to ensure that
they are disengaged. An inadvertently engaged control may limit
functioning of the camera.
Backscatter or “snow” in images
• Position strobes or lights farther away from your lens and at a slight
angle.
• Avoid using strobes in extremely low-visibility conditions.
Spare Parts
• Rear O-Ring # 0110
• Front O-ring # 0132.36
• Waterproof bulkhead cap # 9104.7
• Port Securing Thumbscrews (Set of 3) # 9249.6
• Silicone lubricant # 5020
Limited Warranty
This Ikelite product is warranted against any manufacturing defects for
a period of two (2) years from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at
its sole discretion, repair or replace such products, and will return to
customer postage paid. All other claims of any nature are not covered.
Except as mentioned above, no other warranty expressed or implied
applies to this Ikelite product.
18
Service and Repairs
Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service. No prior authorization is required.
You may return directly to us or through your dealer. Please include a
brief description of the problem, any relevant email correspondence,
and/or description of the service request. Always include name,
shipping address, email address, and phone number inside of the
package.
Send postage paid to:
Ikelite Underwater Systems
Attn: Service Department
50 West 33rd Street
Indianapolis, IN 46208 USA
For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that
the enclosed products were originally manufactured in the USA and
are being returned to the manufacturer for repair service. Value of the
equipment listed for customs purposes should be zero.
19
Contact Us
If you have any questions about your product or need advice on getting
the images you want, please contact us and we’ll do everything we can
to help you capture your unique perspective.
Ikelite Underwater Systems
50 W 33rd St.
Indianapolis, IN 46208 USA
(317) 923-4523
ikelite@ikelite.com
6973.15 canon_M50_2-0818
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising