Ikelite | 200DLM/A Underwater Housing for Olympus OM-D E-M5 III Mirrorless Cameras | Instruction manual | Ikelite 200DLM/A Underwater Housing for Olympus OM-D E-M5 III Mirrorless Cameras Instruction Manual

Ikelite 200DLM/A Underwater Housing for Olympus OM-D E-M5 III Mirrorless Cameras Instruction Manual
200DLM/A Underwater Housing for Olympus OM-D
E-M5 Mark III Mirrorless Camera
Product # 6950.53
Product Registration
Please register your product within 15 days of purchase. Our product
registration database is the quickest way for us to contact you in the
event of a product update.
To register, send a photo of the above registration label to us via
ikelite@ikelite.com along with your name, address, and phone
number.
Introduction
Thank you for your purchase of Ikelite products.
Our primary focus is to provide quality, professional grade products
for use in and under water. Our products are designed, manufactured,
and distributed from our sole facility in Indianapolis, USA where we
started in 1962.
We are available if you have any questions or want photo advice.
Send us an email 24 hours a day to ikelite@ikelite.com. We strive to
reply within 1 business day.
An electronic version of this instruction manual is available for
download via the product page on our website:
https://www.ikelite.com
In the Box
• Housing
• Rear o-ring # 0110 (installed)
• Front o-ring # 0132.36 (installed)
• Camera mount (installed)
• .050” hex key # 0945.11
• 1/16” hex key # 0945.16
• Silicone lubricant 1cc tube
2
Important Notices
»» This housing requires a compatible DLM lens port for
waterproof operation. The housing is not waterproof without a
DLM lens port attached.
»» Do not pull the shutter trigger without a camera installed. You
may accidentally detach or damage the control spring.
»» Never leave a housing in a rinse tank, even if it is the only
system in the tank. Accidental damage may occur when the
user walks away from a housing while it is in the rinse tank.
»» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
»» If you will be using the system in strong surf it is
recommended to draw a vacuum on the housing using the
optional vacuum kit (sold separately).
3
Contents
Product Registration
1
Introduction
2
In the Box
2
Important Notices
3
Getting to Know Your Housing 6
Tray Mounts 9
Accessory Ports 9
Setting Up Your Camera
9
Pre-Installation Checklist 9
Camera Settings 9
Exposure Settings 10
Power Save 10
Back Button Focus 10
Setting Up Your Housing
11
Opening the Housing 11
Installing the Camera 11
Closing the Housing 12
Attaching a Lens Port 13
Setting Up An External Strobe
16
Installing the Lens and Port 13
About Fiber Optic Cords 16
Attaching a Fiber Optic Cord 17
Getting in the Water
17
Final Check 17
Entering the Water 18
Shooting Underwater 18
Learning about Underwater Photography
19
Maintaining Your Housing
19
Post-Dive 19
4
Lens Port 20
Storage 20
Servicing Recommendations 21
Lubricating Controls
21
Lubricating Push Buttons 22
Lubricating Control Shafts 23
Troubleshooting
24
Spare Parts
26
Limited Warranty
27
Service and Repairs
27
Contact Us
28
5
Getting to Know Your Housing
Bulkhead
with cap
Port mount
Shutter
Tray mounts
Lid snap
6
Lens
release
Viewfinder
AEL/AFL
ISO
MENU INFO
OLYMPUS E-M5 III
MADE IN USA
Lid
snap
hook
Rear o-ring
Menu
OK
Left
Down
OLYMPUS E-M5 III
MADE IN USA
Erase
ISO
MENU INFO
ISO
INFO
Up
Right
Playback
7
Front o-ring
Thumbscrew
groove
Buklhead
without cap
Sequential
shooting
LV
On/off
Front dial
Exposure
compensation
Movie
Rear dial
Mode dial
8
Tray Mounts
This housing features two 1/4-20 threaded tray mounts on the bottom
of the housing. The spacing between the tray mounts is 3” (76.2 mm).
Optional tray with handles and mounting hardware are sold separately.
It is recommended to detach and thoroughly rinse the tray mounts,
tray, and mounting hardware, with fresh water routinely during
continuous use and prior to storage.
Accessory Ports
This housing features a spare accessory port which may be used
for the attachment of optional accessories. This port accepts fittings
designed for a 1/2” through or 1/2-20 threaded hole.
The optional Vacuum Kit # 47012 may be installed in place of the side
accessory port. A hand pump with gauge allows you to draw a vacuum
on the house to simulate water pressure and check for leaks prior to
entering the water.
Visit ikelite.com for an updated list of compatible products.
»» Do not remove or loosen the accessory port plug unless you
are installing a compatible accessory.
Setting Up Your Camera
Pre-Installation Checklist
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Remove any attached lanyard or neck strap.
Camera Settings
• Set EVF Auto Switch to “Off.”
9
• Set X-Sync. to “1/250” when using an external strobe.
• Set Flash mode to “Fill in” when using an external strobe.
“Slow2” rear-curtain sync may alternatively be used when using a
compatible DL3 DS Link TTL converter.
Exposure Settings
Refer to the Camera Settings Cheat Sheets in the Photo School
section of our website for recommendations on exposure settings for a
wide variety of shooting situations:
https://www.ikelite.com/blogs/cheat-sheets
Power Save
It is recommended to set the Sleep and Auto Power Off settings to
the shortest intervals that makes sense for your shooting.
Instead of turning the camera off and on to conserve battery, the
camera will automatically sleep after the pre-set interval. To wake the
camera, simply perform an operation such as pressing the shutter
button halfway down.
Back Button Focus
Back button focus takes some adjustment to get used to but can be
very valuable in a variety of shooting scenarios. To set up your camera
for back button focus, set the Custom Menu Setting A1 > AEL/AFL
to “mode3.”
The AEL/AFL button is conveniently accessed by a thumb lever on the
side of the housing. Instead of half-pressing the shutter to obtain focus
and lock focus, press the AEL/AFL button.
For super macro photography, you can use this technique instead of
a manual focus gear. Press and hold AEL/AFL to lock focus at the
minimum focusing distance of your lens. Then move slightly in or out
until the subject is in focus.
10
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and lift the curved end away from
the housing.
Lock
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep firm pressure against the lid snap
while lifting it away.
3. Repeat with opposite lid snap.
4. Remove the housing back.
Installing the Camera
1. Remove any lanyard or neck strap which may be attached to the
camera.
11
2. Line the mount screw up with the camera’s tripod socket. Use a flat
screwdriver to tighten the mount plate to the camera.
Camera
tripod socket
1/4-20 tripod
mount
LENS
Mount screw
3. Extend the camera’s built-in flash if using it to trigger external fiber
optic strobes.
4. Tilt the camera’s LCD screen if desired.
5. Pull out on the housing control knobs to move the controls out of
the way.
6. Insert the mount plate into the slot on the inside bottom of the
housing. Push the camera all of the way forward until it stops.
7. Push housing control knobs in and check orientation with the
camera.
»» The camera may be attached to a tripod using the 1/4-20
threaded mounting hole on the bottom of the mount plate.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The rear housing o-ring does not require lubricant
to make a seal.
12
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
5. Push the lid snaps towards the housing until they are flat against
the housing and the lock has engaged. Close both lid snaps at the
same time.
6. Check the o-ring seal. The o-ring should form a uniform, solid line
visible through the back of the housing.
7. Check control functions.
Attaching a Lens Port
Refer to the DLM/A lens port chart to find compatible lens ports for a
wide variety of popular wide angle, zoom, and macro lenses.
Choose a dome port for wide angle and zoom lenses. Larger diameter
domes are better for split shots (half-in, half-out of the water) and
provide sharper images.
Choose a flat port for macro lenses. Flat ports magnify the subject
underwater. Flat ports are not recommended for wide angle or zoom
lenses due to their limited field of view and risk of vignetting (dark
shadows around the edges of the image).
»» This housing requires a compatible DLM lens port for
waterproof operation. The housing is not waterproof without a
DLM lens port attached.
Installing the Lens and Port
1. If using a zoom gear, refer to the zoom gear instructions for proper
assembly procedure. Attach the lens to the camera.
13
2. Check that the port sealing surface and o-ring are clean and free
of debris.
3. Apply a very thin, even layer of lubricant to the exposed portion of
the front o-ring and to the lens port sealing surface. Avoid dry spots
or uneven build-up of lubricant.
4. Loosen the port thumbscrews until they do not show on the inside
of the lens port.
5. If using a port with a dome shade, align the port so that the tall
projections on the dome shade are in the 12 and 6 o’clock
positions.
Shade
Thumbscrew
Zoom gear
O-ring
Thumbscrew
groove
14
6. Press the port firmly towards the housing until the base of the port
is almost flush with the housing front. If there is resistance, remove
the port and re-check that the thumbscrews are loosened and the
o-ring is properly lubricated.
Small gap
~ 0.15” (4mm)
7. Tighten all three thumbscrews while holding the port firmly towards
the housing. The thumbscrews should thread in completely until
the head touches the port. If the screws are difficult to turn and/or
they bottom out before their heads are flush, it is an indication that
the port is not pushed far enough down on the housing.
15
»» The port must be fully seated onto the housing for waterproof
operation. There should only be a very thin, even gap of
approximately 0.15” (4mm) between the bottom of the port and
the front of the housing.
Setting Up An External Strobe
We recommend attaching an external strobe for the optimal color and
clarity in a wide variety of photographic situations, including daylight
photography.
This housing provides fiber optic ports for optical triggering of up to
two strobes.
An optional bulkhead with TTL flash hotshoe allows electrical
triggering of up to two strobes. Bulkhead and TTL flash hotshoe sold
separately.
About Fiber Optic Cords
Connecting a strobe via fiber optic cord requires the camera’s built-in
flash to fire for every photo. Rapid firing will be limited to the recycle
time of the camera’s built-in flash or the recycle time of the strobe,
whichever is slower.
The following fiber optic cords are compatible with this housing:
• Ikelite Fiber Optic Cord # 4501
• INON Optical D Cable “Non-wireless type” L-Connector
• SEA&SEA Fiber Optic Cable (L-type) # 50107
• SEA&SEA Fiber Optic Cable II # 50128
• Olympus UW Fiber Optic Cable # PTCB-E02
• Nauticam Optical Fiber Cable # 26211 Nauticam to INON
• Nauticam Optical Fiber Cable # 26212 Nauticam to SEA&SEA
»» To connect two strobes to the housing, you must use two fiber
optic cords.
16
Attaching a Fiber Optic Cord
1. Check the end of the fiber optic cord to ensure that it is clean and
smooth.
2. Check that the fiber optic cord o-ring is in place. This o-ring does
not provide waterproofing, but it does keep the fiber optic cord in
place.
3. Attach one end of the fiber optic cord to one of the fiber optic ports
on the housing. The connector is a press-fit into the port.
4. Attach the other end of the fiber optic cord to a compatible strobe.
5. Set the strobe according to the manufacturer recommendations.
6. Turn on the strobe.
7. Turn on the camera. Take a test photo to ensure that your strobe(s)
are functioning properly.
Getting in the Water
Final Check
1. Re-check the rear o-ring seal. The seal should form an even, solid
line visible through the back of the housing.
2. Turn on the camera and check all control functions.
3. Make sure the camera can take a photo.
4. Check camera battery level and available storage space on your
memory card.
17
5. Draw a vacuum on the housing to check for leaks using the
optional vacuum kit, if using (sold separately).
6. Submerge the housing in a fresh water tank dedicated to
underwater photography equipment. Visually confirm that there are
no signs of water intrusion. One sign of water intrusion is a steady
stream of bubbles coming from one of the housing’s seals.
Entering the Water
1. Before entering the water, turn the camera on and operate each
of the housing controls to get a feel for using the camera in the
housing.
2. We recommend entering the water without your housing to ensure
you are comfortable and your life-saving equipment is in working
order. Once you are stable, have someone pass your camera
housing to you.
3. Submerge the housing at the surface of the water and visually
confirm that there are no signs of water intrusion. Look for water
droplets or fogging inside of the housing, or a steady stream of
bubbles coming from one of the housing seals.
4. Use your hand to gently flush away any small bubbles that may be
on the face of the lens port. Bubbles will produce soft focus spots
in your photo or video.
»» If water appears to be entering the housing, point the lens port
downward and return the housing to the surface immediately.
Please observe all necessary safety precautions. NEVER
ascend faster than accepted safety limits.
Shooting Underwater
• Get as close as possible to your subject. For the best results, only
photograph subjects that are less than 6’ (1.8m) away.
• Be careful not to stir up sand or silt.
18
• Photograph subjects straight on or at a slight upward angle.
• If you err in exposure, it is better to have the image slightly
underexposed rather than overexposed. An overexposed image
is missing color information which cannot be adjusted in a photo
processing program. A slightly underexposed image has color
information that can be adjusted.
»» It is important to respect all living creatures underwater,
including people, marine life, and coral. Get as close as you
can to your subjects when taking a photograph, but never
touch or disturb the marine life.
Learning about Underwater Photography
Visit the Photo School section of ikelite.com for a wide range of
information on shooting underwater including:
• Product Tutorials and Videos
• Cheat Sheets with exposure setting recommendations for a wide
variety of situations
• Advanced Techniques with in-depth articles on different shooting
techniques
• Frequently Asked Questions
• Photo Galleries showing examples of real results underwater
• Feature Articles and more!
Maintaining Your Housing
Post-Dive
1. Rinse the housing in fresh water. Rotate the housing controls and
press each button several times while submerged in fresh water to
flush out any salt or debris to ensure smooth operation on future
dives.
19
2. NEVER leave your housing in a fresh water rinse tank, even if it is
the only system in the tank. Collisions with another person’s gear
can cause scratches or damage to your equipment. Accidental
damage occurs most often in the rinse tank.
3. Rinse off any residual residue from the rinse tank with clean,
running fresh water.
4. Stow the housing in a shaded place where it is protected from
impact and overheating. If no shade is available, cover the housing
with a light colored towel or cloth.
5. Check the memory card capacity and battery life of your camera
and strobe(s). Recharge as necessary.
6. Always re-check the o-ring seal after opening the housing.
7. If using an electrical sync cord, detach the cord plug or bulkhead
cap and lubricate the threads, o-ring(s) and sealing surface(s)
every 2-3 days during continuous use.
Lens Port
Treat the surface of the lens port like a camera lens. After use, rinse
and gently dry the outside lens port to avoid water spotting. Use only a
microfiber lens cleaning cloth to avoid scratches. To clean, use a mild
soap solution.
»» Do not rinse the inside of the lens port.
»» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
Storage
1. Clean the housing and controls thoroughly prior to storage.
20
2. Remove the rear o-ring. Place in a small re-sealable plastic bag
inside of the housing.
3. Leave the lid snaps open to release pressure on the lid snap
springs.
4. Store the housing in a cool, dry place away from direct sunlight
and chemicals.
5. Before using the housing, check the tightness of the set screw in
each control knob. Check each control gland to make sure they are
snug. There is a slight chance that either could vibrate loose during
travel.
»» Do not leave the camera and housing in direct sunlight for
prolonged periods. Heat may damage the camera.
»» Do not transport with the camera inside of the housing.
»» Do not store the housing in a humid environment. Prolonged
exposure to high humidity may damage electronic
components.
Servicing Recommendations
It is recommended that the housing be sent to Ikelite or an authorized
service center annually for routine service and maintenance. Service
may be required more or less frequently depending on care and use.
Lubricating Controls
The housing’s controls may need to be lubricated if they become
particularly difficult to use or if the o-rings have dried out during longer
periods of storage.
21
There will be some breaking force required to move the controls
initially after the housing has been in storage for long periods of time.
Remove controls for lubrication only if they continue to stick after
applying a small amount of lubricant to the exposed portion of the
shafts and working them many times.
»» Use only Ikelite lubricant. Other types of lubricant may cause
swelling of o-rings or cracking of plastic components.
»» Lubricant is not a sealant; it is used to reduce friction.
Excessive lubricant can collect sand, hair or debris which may
interfere with proper sealing.
»» Never use spray lubricants as the propellant ingredient can
cause the plastic housing to crack or o-rings to swell.
Lubricating Push Buttons
1. Press and hold the push button all the way in.
2. Place a small amount of lubricant at the base of the push button
shaft inside the housing.
3. Press and release the push button several times to work the
lubricant into the o-ring.
4. If a push button control becomes difficult to push or if it sticks when
depressed, soak the housing in warm, soapy fresh water. After a
few minutes, operate the push button. If this does not correct the
problem, return the housing to Ikelite for maintenance.
22
»» To prevent build-up of salt, sand, or debris, the push buttons
should be flushed with fresh, clean water after every use.
Depress each push button while the housing is submerged in
fresh water.
»» If it is necessary to remove a housing push button, NEVER
re-use the e-clip. Push button o-ring kits include replacement
e-clips.
»» Push buttons look similar but vary in length. Remove and reinstall one push button at a time.
Lubricating Control Shafts
1. Loosen the knob set screw using a hex key.
2. Remove the control shaft from the inside of the housing.
3. Clean and lightly lubricate the shaft, including the large outer end
of the shaft.
4. If there is a spring associated with the control, make sure it is in its
proper position.
Control
shaft
Housing
Control
gland
Knob
set
screw
Control
flat
23
5. Re-install the shaft from the inside of the housing. Rotate the shaft
gently for smooth installation into the gland. Push the control shaft
all of the way through until the flat of the shaft is visible on the
outside of the housing.
6. Align the knob set screw with the control flat.
7. Tighten the set screw firmly against the flat of the control shaft
using a hex key.
8. Check that the set screw is oriented properly by holding the control
shaft in place on the inside of the housing while attempting to
rotate the control knob on the outside of the housing. If there is
rotation, loosen the set screw and realign with control flat; retighten
and recheck.
»» We do not recommend removing the control gland from the
housing.
»» Always take the housing underwater to depth without a camera
after removing and re-installing controls.
»» Remove and re-install one control at a time.
»» DO NOT pull the shutter trigger without a camera installed. You
may accidentally detach or damage the control spring.
Troubleshooting
Water enters the housing
• Check and reinstall the rear o-ring.
• Replace the o-ring if there are any signs of cracks or tears.
• Take the housing underwater to depth without a camera installed to
ensure that the leaking has been corrected.
24
Photos are over-exposed (too light)
• Adjust aperture (smaller), shutter speed (faster), or ISO (lower)
setting.
• Move light(s) farther away from your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
Photos are under-exposed (too dark)
• Adjust aperture (larger), shutter speed (slower), or ISO (higher)
setting.
• Move light(s) closer to your subject and make sure they are pointed
in the right direction.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
Strobe(s) will not fire
• Turn on strobe.
• Check the strobe(s) battery life.
• Restore the camera to factory default settings. There are some
camera settings that will prevent an external flash from firing.
• Check camera settings recommended for use with an external
strobe in the beginning of this manual.
• Check that the fiber optic cord or electrical sync cord is properly
attached.
• If using, check that the hotshoe is pushed all of the way forward on
the camera.
25
Button(s) are sticking
• Soak the housing in lukewarm fresh water. Depress each button
several times while the housing is submerged. Rinse the housing
with running fresh water.
• Lubricate the controls.
Button(s) or control(s) not operating
• Tighten the camera mounting plate with a screwdriver.
• Ensure that nothing is preventing the camera from going all of the
way into the housing.
• Check that the camera mounting plate is pushed all of the way
forward.
Camera is not functioning normally underwater
• Check each housing control while underwater to ensure that
they are disengaged. An inadvertently engaged control may limit
functioning of the camera.
• Check that no controls are being accidentally pressed.
• Check that the shutter is not half depressed. If the shutter spring
has been damaged by activation without a camera installed, it may
not return properly. Adjust or replace the shutter spring.
Backscatter or “snow” in images
• Reposition strobe(s) or light(s) to light up the subject only and not
the water in-between the camera and subject.
• Avoid using strobes in extremely low-visibility conditions.
Spare Parts
Rear o-ring # 0110
26
Front o-ring # 0132.36
Trigger lever extension # 4077.93
Silicone lubricant # 5020
Push button o-ring kit # 6201.03
.050” hex key # 0945.11
1/16” hex key # 0945.16
Limited Warranty
This Ikelite product is warranted against any manufacturing defects for
a period of two (2) years from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at
its sole discretion, repair or replace such products, and will return to
customer postage paid. All other claims of any nature are not covered.
Except as mentioned above, no other warranty expressed or implied
applies to this Ikelite product.
Service and Repairs
Ikelite is most interested in performing any service to ensure that all
products perform as intended.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or description of the service
request. Always include name, shipping address, email address, and
phone number inside of the package. Send postage paid to:
27
Ikelite Underwater Systems
Attention: Service Department
50 W 33rd St
Indianapolis, IN 46208 USA
+1 (317) 923-4523
service@ikelite.com
For detailed instructions on returning your product for service including
important information on international customs documentation, please
refer to our website at:
https://www.ikelite.com/pages/service-repairs
Contact Us
If you have any questions about your product or need advice on
getting the images you want, please get in touch with us and we’ll do
everything we can to help you capture your unique perspective.
Ikelite Underwater Systems
50 W 33rd St
Indianapolis, IN 46208 USA
+1 (317) 923-4523
ikelite@ikelite.com
28
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising