Ikelite | DLM Standard Flat Port | Instruction manual | Ikelite DLM Standard Flat Port Instruction Manual

Ikelite DLM Standard Flat Port Instruction Manual
5. Loosen the three securing thumbscrews on the port until
they do not show on the inside of the lens port.
Thumbscrew
DLM Standard Flat Port
Product # 5516.45
O-ring
Included in the Box
Thumbscrew
groove
• Flat port
• Securing thumbscrews (set of 3) # 9249.6 (installed)
• Vinyl cover # 0200 (installed)
• Silicone lubricant 1cc tube
Important Notices
6. Press the port firmly towards the housing until the base of
the port is almost flush with the housing front. If there is
resistance, remove the port and re-check that the
thumbscrews are loosened and that the o-ring is properly
lubricated.
»» Do not use alcohol, cleaning agents, spray lubricants,
Rain-X, or other solvents on the housing or lens port.
Use of an incompatible chemical compound can
damage the plastic or component o-rings, which may
result in leaking.
Small gap
~ 0.15” (4mm)
7. Tighten all three thumbscrews while holding the port
Installation and Use
Installing the Flat Port
firmly towards the housing. The thumbscrews should
thread in completely until the head touches the port. If the
screws are difficult to turn and/or they bottom out before
their heads are flush, it is an indication that the port is not
pushed far enough down on the housing.
1. Attach the lens to the camera.
2. Remove the vinyl cover from the flat port.
3. Check that the port sealing surface is clean and free of
debris.
4. Apply a very thin, even layer of lubricant to the exposed
portion of the housing’s front o-ring and to the lens port
sealing surface. Avoid dry spots or uneven build-up of
lubricant.
»» The port must be fully seated onto the housing for
waterproof operation. There should only be a very thin,
even gap of approximately 0.15” (4mm) between the
bottom of the port and the front of the housing.
Testing the Housing
1. Assemble the housing without a camera installed.
2. Submerge the housing in fresh water for several minutes.
3. Remove the housing from water and dry the outside of the
housing with a clean, lint-free cloth.
4. Look through the back of the housing for signs that water
has entered the housing. Signs include fogging or water
droplets.
5. We recommend making at least one dive without a
camera installed to ensure waterproof operation.
Maintenance and Storage
Post-Dive
1. Rinse the housing with flat port installed in clean, fresh
water.
2. Never leave your housing in the fresh water rinse tank.
Collisions with other gear can cause scratches or damage
to your equipment.
3. Dry the glass with a clean micro fiber lens cleaning cloth.
4. Attach the protective vinyl cover.
5. Stow the housing in a shaded place where it is protected
from impact or overheating. If no shade is available, we
recommend covering the housing with a towel or cloth.
Travel and Storage
1. Clean and dry the exterior of the flat port. Do not use any
type of alcohol or glass or surface cleaner on the flat port.
2. Attach the protective vinyl cover.
3. Store in a cool, dry place.
Limited Warranty
This Ikelite product is warranted against any manufacturing
defects for a period of one (1) year from the original date
of purchase. To obtain warranty service, the product must
be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return
to customer postage paid. All other claims of any nature are
not covered. Except as mentioned above, no other warranty
expressed or implied applies to this Ikelite product.
Contact Us
Ikelite Underwater Systems
50 W 33rd St
Indianapolis, IN 46208 USA
(317) 923-4523
ikelite@ikelite.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising