Ikelite | Zoom / Focus Gear 5509.18 | Instruction manual | Ikelite Zoom / Focus Gear 5509.18 Instruction Manual

Ikelite Zoom / Focus Gear 5509.18 Instruction Manual
Installation Procedure (cont.)
1. Install your Nikon camera and lens in your Ikelite housing.
Zoom Clamp and Sleeve
2. Remove
the lens from the camera body, using the Ikelite
properly installed
housing control located on the side of the housing.
Ikelite Zoom Clamp/Sleeve
installation instructions
3. Place the clear plastic Gear Sleeve #5509.18 into the port
opening (Fig A).
for
4. Make sure that the Black Housing Gear teeth mesh properly
with the Gear Sleeve teeth.
Nikon 18-105mm VR Lens
Figure
C
IKELITE
Black Housing
Gear
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
Gear
Gear Sleeve
Sleeve
When returning products
send “attn. Repair Dept.”
Posts
#5509.18
“general questions” e-mail: ikelite@ikelite.com
www.ikelite.com
317-923-4523
Go to www.ikelite.com for complete product and accessory info.
Figure A
Nik18-105installguide-5509.18-02-0410
42
Installation Procedure (cont.)
Installation Procedure (cont.)
Ikelite Zoom Clamp/Sleeve
5. Attach the #9059.9 Black Zoom Clamp (included with all Ikelite
DSLR housings), to the lens as shown (Fig. B).
Zoom Clamp and Sleeve
properly installed
installation instructions
6. Lower the lens into the housing opening. Make sure to line up
the Black Zoom Clamp Grooved Tabs with the Gear Sleeve
posts (Fig. B).
forslide into the Gear Sleeve. Due
7. The clamp and springs will NOT
to the lens diameter, the clamp must be seated on the lens
barrel ABOVE the top of the gear sleeve (Fig. C, Page 4). Only
the Grooved Tabs below the Clamp body will slide into the Gear
Sleeve Posts.
Nikon 18-105mm VR Lens
Figure C
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
When returning products send “attn. Repair Dept.”
“general questions” e-mail: ikelite@ikelite.com
www.ikelite.com
317-923-4523
8 Rotate the lens counter-clockwise until it locks into the camera
body (Fig. C, Page 4).
9. Make sure the Gear
Sleeve teeth and Black
Housing Gear are meshed
properly, and then install
the housing port. Check
function using the
housing zoom control
knob.
Grooved Tab
TOP OF HOUSING
Figure B
Go to www.ikelite.com for complete product and accessory info.
Nik18-105installguide-5509.18-02-0410
4
3
Gear Sleeve Post
Installation Procedure (cont.)
Installation Procedure
1. Install your Nikon camera and lens in your Ikelite housing.
2. Remove the lens from the camera body, using the Ikelite
housing control located on the side of the housing.
3. Place the clear plastic Gear Sleeve #5509.18 into the port
opening (Fig A).
4. Make sure that the Black Housing Gear teeth mesh properly
with the Gear Sleeve teeth.
Ikelite Zoom Clamp/Sleeve
5. Attach the #9059.9 Black Zoom Clamp (included with all Ikelite
DSLR housings), to the lens as shown (Fig. B).
installation instructions
6. Lower the lens into the housing opening. Make sure to line up
the Black Zoom Clamp Grooved Tabs with the Gear Sleeve
posts (Fig. B).
forslide into the Gear Sleeve. Due
7. The clamp and springs will NOT
to the lens diameter, the clamp must be seated on the lens
barrel ABOVE the top of the gear sleeve (Fig. C, Page 4). Only
the Grooved Tabs below the Clamp body will slide into the Gear
Sleeve Posts.
Nikon 18-105mm VR Lens
IKELITE
Black Housing
Gear
Gear
Sleeve
Posts
Gear Sleeve
#5509.18
8 Rotate the lens counter-clockwise until it locks into the camera
body (Fig. C, Page 4).
9. Make sure the Gear
Sleeve teeth and Black
Housing Gear are meshed
properly, and then install
the housing port. Check
function using the
housing zoom control
knob.
Grooved Tab
TOP OF HOUSING
Figure B
Gear Sleeve Post
Figure A
3
2
Installation Procedure (cont.)
Installation Procedure (cont.)
1. Install your Nikon camera and lens in your Ikelite housing.
Zoom Clamp and Sleeve
2. Remove
the lens from the camera body, using the Ikelite
properly installed
housing control located on the side of the housing.
3. Place the clear plastic Gear Sleeve #5509.18 into the port
opening (Fig A).
4. Make sure that the Black Housing Gear teeth mesh properly
with the Gear Sleeve teeth.
Figure
C
IKELITE
Black Housing
Gear
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
Gear
Gear Sleeve
Sleeve
When returning products
send “attn. Repair Dept.”
Posts
#5509.18
“general questions” e-mail: ikelite@ikelite.com
www.ikelite.com
317-923-4523
5. Attach the #9059.9 Black Zoom Clamp (included with all Ikelite
DSLR housings), to the lens as shown (Fig. B).
6. Lower the lens into the housing opening. Make sure to line up
the Black Zoom Clamp Grooved Tabs with the Gear Sleeve
posts (Fig. B).
7. The clamp and springs will NOT slide into the Gear Sleeve. Due
to the lens diameter, the clamp must be seated on the lens
barrel ABOVE the top of the gear sleeve (Fig. C, Page 4). Only
the Grooved Tabs below the Clamp body will slide into the Gear
Sleeve Posts.
8 Rotate the lens counter-clockwise until it locks into the camera
body (Fig. C, Page 4).
9. Make sure the Gear
Sleeve teeth and Black
Housing Gear are meshed
properly, and then install
the housing port. Check
function using the
housing zoom control
knob.
Grooved Tab
TOP OF HOUSING
Figure B
Go to www.ikelite.com for complete product and accessory info.
Figure A
Nik18-105installguide-5509.18-02-0410
42
3
Gear Sleeve Post
Installation Procedure (cont.)
Installation Procedure (cont.)
5. Attach the #9059.9 Black Zoom Clamp (included with all Ikelite
DSLR housings), to the lens as shown (Fig. B).
6. Lower the lens into the housing opening. Make sure to line up
the Black Zoom Clamp Grooved Tabs with the Gear Sleeve
posts (Fig. B).
Zoom Clamp and Sleeve
properly installed
7. The clamp and springs will NOT slide into the Gear Sleeve. Due
to the lens diameter, the clamp must be seated on the lens
barrel ABOVE the top of the gear sleeve (Fig. C, Page 4). Only
the Grooved Tabs below the Clamp body will slide into the Gear
Sleeve Posts.
8 Rotate the lens counter-clockwise until it locks into the camera
body (Fig. C, Page 4).
9. Make sure the Gear
Sleeve teeth and Black
Housing Gear are meshed
properly, and then install
the housing port. Check
function using the
housing zoom control
knob.
Grooved Tab
TOP OF HOUSING
Figure B
Figure C
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
When returning products send “attn. Repair Dept.”
Gear Sleeve Post
“general questions” e-mail: ikelite@ikelite.com
www.ikelite.com
317-923-4523
Go to www.ikelite.com for complete product and accessory info.
Nik18-105installguide-5509.18-02-0410
3
4
Installation Procedure (cont.)
Zoom Clamp and Sleeve
properly installed
Figure C
Ikelite Underwater Systems
50 W 33rd Street
Indianapolis, IN 46208 USA
When returning products send “attn. Repair Dept.”
“general questions” e-mail: ikelite@ikelite.com
www.ikelite.com
317-923-4523
Go to www.ikelite.com for complete product and accessory info.
Nik18-105installguide-5509.18-02-0410
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising