Ikelite | Action Housing for Canon PowerShot G7 X Mark II | Instruction manual | Ikelite Action Housing for Canon PowerShot G7 X Mark II Instruction Manual

Ikelite Action Housing for Canon PowerShot G7 X Mark II Instruction Manual
Included in the Box
• Housing
• Vinyl Port Cover
Action Housing for Canon G7 X Mark II
Product Number 6245.08
• Lanyard
• Silicone Lubricant 1cc tube
Getting to Know Your Housing
Important Notices
»» Never use alcohol, spray lubricants, glass cleaner, or
surface cleaner on this product.
Shutter Button
Zoom Lever
Power Button
Latch
»» Rinse with fresh water after each dive.
»» Do not leave unattended in a rinse tank.
»» Always assemble in a cool, dry location. Opening the
housing in a humid environment will lead to fogging.
Product Registration
Please register your product at ikelite.com within 15 days of
purchase. Our product registration database is the best way
for us to get a hold of you in the event of a product update or
recall.
Rubber Grip
Lens Port
Tray Mounts
Shutter Button
Single Erase
Power Button
Up Button
Limited Warranty
Movie Button
This Ikelite product is warranted against any manufacturing
defects for a period of two (2) years from the original date of
purchase. Defective products should be returned to Ikelite
postage paid. Ikelite will, at its sole discretion, repair or
replace such products, and will return to customer postage
paid. All other claims of any nature are not covered. Except
as mentioned above, no other warranty expressed or implied
applies to this Ikelite product.
Quick Set/
Menu
Flash/Right
Button
ULTRAcompact
Made in USA
Macro/Left Button
MENU Button
INFO/Down Button
Playback Button
Opening the Housing
Closing the Housing
Latch Buttons
1. Clean and lightly lubricate the housing o-ring. Use only
enough lubricant to make the o-ring appear uniformly shiny.
Lubricant is not a sealant. Excessive lubricant may attract
debris and adversely affect the seal.
2. Rotate the housing back 180º until it meets the front.
PUSH TO
UNLOCK
3. Latch the housing back and press the latch towards the
housing until the lock buttons click into place.
1. Thoroughly dry the housing if wet. To reduce the likelihood
of fogging, only open the housing in a cool, dry place. If
possible open only in an air conditioned room.
4. Check the latch. The buttons will not be depressed when the
latch is properly locked. Pulling on the latch without pressing
the buttons should not allow the latch to open.
2. Depress both latch buttons and rotate the latch away from
the housing.
Post-Dive
3. The back of the housing will be compressed by pressure
after taking it underwater or in an airplane. Rotate the latch
fully to break the seal of the housing.
4. Lift the latch up and away from housing.
5. Carefully open the housing back and rotate it 180º to the
opposite side of the housing. Do not use metal objects or
tools to pry the back open, as this may damage the o-ring or
sealing surface.
Installing the Camera
1. Remove any lanyard, neck strap, or accessory attached to
the camera.
2. Pull out any camera control knobs until they stop.
3. Place the camera into the front of the housing with the lens
centered in the lens port.
4. Make sure the camera is sitting flat in the housing and flush
to the front Support Ribs.
Support Ribs
1. Rinse the housing in fresh water. Rotate the housing’s
controls and press each button while submerged in fresh
water to flush out any salt or debris to ensure smooth
operation on future dives.
2. NEVER leave your housing in the fresh water rinse tank.
Collisions with other peoples’ gear can cause scratches or
damage to your equipment.
3. Stow the housing in a shaded place where it is protected
from impact or overheating. If no shade is available, we
recommend covering the housing with a towel or cloth.
4. Check the memory card capacity and battery life of your
camera and lighting. Recharge as necessary.
5. Always re-check o-ring seal after opening the housing.
Travel and Storage
1. Remove the camera from the housing for travel or storage.
2. Check the main housing o-ring.
3. Close the empty housing and submerge in lukewarm fresh
water. While submerged, rotate each control and depress
each button to flush out any salt or debris.
4. Remove the housing from water and rinse with running
water.
Lens Port
5. Do not rinse the inside of the housing or submerge the open
housing in water. If the inside of the housing needs to be
cleaned, wipe with a clean, slightly damp cloth.
6. Dry the housing with a clean, lint-free cloth.
7. Store in a cool, dry place.
8. We recommend careful care and cleaning along with
periodic factory service of the seals.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising