Ikelite | Underwater Housing for Canon PowerShot G7 X Mark II | Instruction manual | Ikelite Underwater Housing for Canon PowerShot G7 X Mark II Instruction Manual

Ikelite Underwater Housing for Canon PowerShot G7 X Mark II Instruction Manual
Underwater Housing for Canon G7X Mark II
Product Number 6146.08
Product Registration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to contact you
in the event of a product update.
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product to
receive information on any updates, or notices pertaining to your
equipment.
Included in the Box
• Housing
• Port cover # 0200
• Silicone lubricant 1cc tube
Specifications
• 200 ft (60m) depth rating
• Controls for all camera controls except Flash switch and Mobile
Device Connection button
• Near neutral buoyancy in fresh water
• 1/4-20 thread tray mounting with 3-inch (76mm) spacing
• Weight 2.9 lb (1.3 kg)
• Dimensions 6 x 5.4 x 6.9” (152 x 137 x 175 mm)
• 3 inch (76 mm) diameter glass lens port
2
Important Notices
»» To prevent salt build-up and sticking controls, turn the camera
off and submerge the sealed housing in clean, freshwater.
Operate the controls several times each while underwater to
flush out any residue.
»» Never leave a housing in a rinse tank, even if it is the only
system in the tank. Most catastrophic floods happen when the
user walks away from a housing while it is in the rinse tank.
»» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
3
Contents
Product Registration
1
About this Product
2
Included in the Box
2
Specifications
2
Important Notices
3
Getting to Know Your Housing 5
Accessory Port
7
Setting Up Your Camera
7
Setting Up Your Housing
8
Installing an Accessory via the Accessory Port 7
Pre-Installation Checklist & Initial Camera Settings 7
Opening the Housing 8
Inserting the Camera 8
Closing the Housing 9
Attaching a Fiber Optic Strobe 10
Final Check 11
Entering the Water 11
Maintenance
12
Post-Dive 12
Travel and Storage 12
Spare Parts
13
Troubleshooting
13
Limited Warranty
15
Service and Repairs
15
Contact Us
16
4
Getting to Know Your Housing
Zoom Lever
Shutter Button
Power Button ON/OFF
Control Ring
Mode Dial
Accessory Port
Hole Plug
Rubber Grip
Fiber Optic Ports
Lid Snap
Lens Port
Tray Mounts
5
O-Ring
RING
FUNC
REC
MF
INFO
MENU
Lanyard
Camera Mounting Plate
Camera Mounting Tray
Lid Hook
Exp. Comp.
Dial
Control Dial
Ring Function
Selector/Single Erase
RING
FUNC
REC
Drive Mode/Up
Button
MF
Macro/Left Button
INFO
Playback Button
MENU
INFO Button
6
Movie Button
Flash/Right Button
Q SET Menu/SET
MENU Button
Accessory Port
Your housing features one 1/2-20 threaded Accessory Port which
may be used for attachment of factory optional or aftermarket housing
accessories. Visit ikelite.com for an updated list of factory optional
accessories.
Installing an Accessory via the Accessory Port
1. Remove the Hole Plug using an 11/16” open end wrench.
2. Check the accessory fitting o-ring sealing area. Check o-ring and
housing o-ring sealing area. All should be clean and free of hair,
sand, or other debris.
3. Lightly lubricate o-ring with Ikelite lubricant. Use ONLY Ikelite
lubricant. Other manufacturer lubricants can cause the o-ring to
swell.
4. Carefully screw in and tighten accessory fitting. The accessory port
features a 1/2-20 threaded hole. Make sure your fitting is the same
thread pattern. DO NOT cross-thread. DO NOT overtighten.
5. After installing an accessory, pressure test the housing by diving
without a camera inside.
NOTICE: Your Ikelite housing warranty DOES NOT extend
to cover the attachment of aftermarket housing accessories by
3rd parties. Warranty DOES cover factory optional accessories
attached by certified Ikelite service technicians.
Do not remove the Accessory Port Hole Plug unless you are
installing a compatible accessory.
Setting Up Your Camera
Pre-Installation Checklist & Initial Camera Settings
1. Insert a fully charged camera battery.
7
2. Insert a properly formatted memory card.
3. Set Mode Dial to “M” Manual. This will allow you to adjust aperture
and shutter speed settings to suit your shooting situation.
4. Set AF-assist beam to “OFF” and ISO to “200.”
5. Set Red-Eye Lamp to “OFF.”
Once underwater, camera functions can be adjusted for each shooting
situation.
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep firm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snap.
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap attached to the camera.
8
2. Remove the camera Mounting Plate from the housing.
3. Line the mounting screw up with the camera’s tripod socket. Use a
coin or flat head screwdriver to tighten the Mounting Plate to the
camera.
Mounting screw
Camera tripod
socket
Mounting
Plate
BOTTOM
FRONT
SIDE
4. Pull out on the housing control knobs to move them out of the way.
5. Insert the Mounting Plate into the slot on the inside bottom of the
housing. Push the camera all of the way forward until the back of
the Mounting Plate is flush with the back of the housing mount.
6. Pop up the flash before installing the camera into the housing
when triggering an external strobe. Once the camera is closed in
the housing, the flash CANNOT be raised.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The main o-ring does not require lubricant to make
a seal.
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
9
5. Push the lid snaps toward the housing until they are flat against the
housing and the lock has engaged. Close opposing lid snaps at the
same time.
6. Check the o-ring seal. The o-ring should form a uniform, solid line
around the back of the housing. There will be a small, even gap
around the housing between the housing back and the housing
front.
Attaching a Fiber Optic Strobe
1. Check the end of the fiber optic cord to ensure that it is clean and
smooth.
2. Ensure that the Fiber Optic Cord O-ring is in place. This o-ring
does not provide waterproofing, however it does keep the fiber optic
cord in place.
3. Attach one end of the fiber optic cord into one of the fiber optic
ports on the front of the housing. The connector is a press-fit into
the fiber optic port.
Fiber Optic Cord
O-ring
4. Attach the other end of the fiber optic cord to a compatible strobe.
5. Set the strobe to the appropriate setting based on manufacturer
recommendations.
6. Turn the camera on.
7. Turn the strobe(s) on.
10
8. Take a test photo to ensure that your strobe(s) are functioning
properly.
Final Check
1. Re-check the o-ring seal. The seal should form an even, solid line
around the back of the housing.
2. Turn on the camera and check all control functions.
3. Make sure that the camera can obtain focus and take a photo.
4. Check battery life and open storage space on your memory card.
5. Check the flash, if using.
6. Submerge the housing in a fresh water tank dedicated to
underwater photography equipment. Visually confirm that there are
no signs of water intrusion or a steady stream of bubbles coming
from one of the housing seals.
Entering the Water
1. If possible, we recommend entering the water without your housing
to ensure that you are comfortable and your life-saving equipment
is in working order. Once you are stable, have someone pass your
camera housing to you.
2. Submerge the housing at the surface of the water and visually
confirm that there are no signs of water intrusion or a steady stream
of bubbles coming from one of the housing seals. If water does
appear to be entering the housing, point the lens port downward
and return the housing to the surface as quickly as possible. Please
observe all necessary safety precautions. NEVER ascend faster
than accepted safety limits.
3. Use your hand to gently flush away any small bubbles that may be
on the face of the lens port. Bubbles will produce soft focus spots in
your photo or video.
11
Maintenance
Post-Dive
1. Rinse the housing in fresh water. Rotate the housing controls and
press each button while submerged in fresh water to flush out any
salt or debris to ensure smooth operation on future dives.
2. NEVER leave your housing in the fresh water rinse tank. Collisions
with another person’s equipment can cause scratches and possible
damage to your equipment.
3. Stow the housing in a shaded place where it is protected from
impact or overheating. If no shade is available, we recommend
covering the housing with a towel or cloth.
4. Check the camera’s memory card capacity before your next dive.
Check the battery life of your camera and strobe(s); recharge as
necessary.
5. Always re-check o-ring seal after opening the housing.
Travel and Storage
1. Remove the camera from the housing for travel or storage.
2. Check the main housing o-ring.
3. Close the empty housing and submerge in lukewarm fresh water.
While submerged, rotate each control and depress each button to
flush out any salt or debris.
4. Remove the housing from water and rinse with running water.
5. Do not rinse the inside of the housing or submerge the open
housing in water. If the inside of the housing needs to be cleaned,
wipe with a clean, slightly damp cloth.
6. Dry the housing with a clean, lint-free cloth.
7. Store in a cool, dry place.
12
8. Like regulators and other pressure-sensitive equipment,
we recommend careful care and cleaning along with annual
replacement of the factory seals.
Spare Parts
• Main o-ring # 0109
• Port Cover # 0200
Troubleshooting
Water enters the housing
• Reclean and reinstall the main o-ring.
• Take the housing underwater without a camera installed to ensure
that the leaking has been corrected.
Photos are over-exposed (too light)
• Adjust aperture (smaller), shutter speed (faster), or ISO (lower)
setting.
• Move lights(s) farther away from your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
Photos are under-exposed (too dark)
• Adjust aperture (larger), shutter speed (slower), or ISO (higher)
setting.
• Move light(s) closer to your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
13
Strobe will not fire
• Turn on strobe.
• Make sure that the camera’s flash is set to fire on every photo.
• Check that the fiber optic cord is properly attached.
Buttons are stuck
• Soak the housing in lukewarm fresh water. Depress each button
several times while the housing is submerged.
• Apply lubricant to the button. Press the button several times to
distribute the lubricant.
Button(s) or control(s) do not line up
• Ensure that nothing is preventing the camera from going into the
housing.
• Push the camera mounting plate forward until it is flush with the
housing base plate.
Camera is not functioning normally underwater
• Ensure that the camera mounting plate is pushed all of the way into
the housing mounting plate.
• Check each housing control while underwater to ensure that
they are disengaged. An inadvertently engaged control may limit
functioning of the camera.
• Check that the zoom control is disengaged.
Backscatter or “snow” in images
• Position strobes or lights farther away from your lens and at a slight
angle. Do not light water between the camera and subject.
• Avoid using strobes in extremely low-visibility conditions.
14
Limited Warranty
This Ikelite product is warranted against any manufacturing defects for
a period of two (2) years from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at
its sole discretion, repair or replace such products, and will return to
customer postage paid. All other claims of any nature are not covered.
Except as mentioned above, no other warranty expressed or implied
applies to this Ikelite product.
Service and Repairs
Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or description of the service
request. Always include name, shipping address, email address, and
phone number inside of the package. Send postage paid to:
Ikelite Underwater Systems
Attn: Service Department
50 West 33rd Street
Indianapolis, IN 46208 USA
For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that
the enclosed products were originally manufactured in the USA and
are being returned to the manufacturer for repair service. Value of the
equipment listed for customs purposes should be zero.
15
Contact Us
If you have any questions about your product or need advice on
getting the images you want, please get in touch with us and we’ll do
everything we can to help you capture your unique perspective.
Ikelite Underwater Systems
50 W 33rd St
Indianapolis, IN 46208 USA
(317) 923-4523
ikelite@ikelite.com
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising