Ikelite | Underwater Housing for Panasonic Lumix ZS100, TZ100, TZ101 | Instruction manual | Ikelite Underwater Housing for Panasonic Lumix ZS100, TZ100, TZ101 Instruction Manual

Ikelite Underwater Housing for Panasonic Lumix ZS100, TZ100, TZ101 Instruction Manual
Underwater Housing for
Panasonic Lumix DMC-ZS100, DMC-TZ100
Product Number 6170.10
Product Registration
Please register your product at ikelite.com within 15 days of purchase.
Our product registration database is the best way for us to get a hold
of you in the event of a product update or recall.
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please visit ikelite.com to register your product to
receive information on any updates, notices, or recalls pertaining to
your equipment.
Included in the Box
• Housing
• Vinyl port cover # 0200.08
• Silicone lubricant
2
Important Notices
»» Never leave a housing in a rinse tank, even if it is the only
system in the tank. The vast majority of catastrophic floods
happen when the user walks away from a housing while it is in
the rinse tank.
»» To prevent salt build-up and sticking controls, submerge the
empty housing in clean, freshwater. Operate the controls
several times each while underwater to flush out any residue.
»» Do not use alcohol, cleaning agents, spray lubricants, Rain-X,
or other solvents on the housing or lens port. Use of an
incompatible chemical compound can damage the plastic and
o-rings, and may result in leaking.
3
Contents
Product Registration
1
About this Product
2
Included in the Box
2
Important Notices
3
Getting to Know Your Housing 5
Setting Up Your Camera
7
Setting Up Your Housing
7
Getting to Know Your Housing - cont. 6
Pre-Installation Checklist 7
Opening the Housing 7
Inserting the Camera 8
Closing the Housing 9
Final Check 9
Entering the Water 10
Setting Up An External Strobe
11
About the Built-In Flash 11
Attaching a Fiber Optic Cord 11
Maintenance
12
Post-Dive 12
Travel and Storage 12
Troubleshooting
13
Limited Warranty
15
Service and Repairs
15
Contact Us
16
4
Getting to Know Your Housing
Rear Dial
Motion Picture Button
Zoom Lever
Shutter
Mode Dial
Fiber Optic Ports
Lens Port
Lid Snap
Tray Mounts
5
Getting to Know Your Housing - cont.
O-Ring
Power ON/OFF
Fn4/
LFV
AF/AE
LOCK
4K
Fn1
Fn2
MF
WB
DISP
Camera Mounting Plate
Lanyard
Lid Hook
Camera Mounting Tray
Fn4/LVF Button
AF/AE Lock
Fn4/
LFV
AF/AE
LOCK
4K / Fn1 Button
4K
Fn1
Fn2
Fn2 / Post Focus
Playback
MENU/SET Button
MF
MF / Macro
WB
WB White Balance
Q. MENU / Delete Button
DISP
Self-Timer
6
MENU/SET
DISP Button
Setting Up Your Camera
Pre-Installation Checklist
1. Insert a fully charged camera battery.
2. Insert a properly formatted memory card.
3. Set AF Assist Lamp and Red-Eye Removal to “OFF.”
4. Set Eye Sensor LVF/Monitor Switch to “MON.”
5. Set Touch Settings - Touch Screen to “OFF.”
6. Set Step Zoom function in the Custom menu > zoom lever > Q
CAUTION: Zoom the camera in small steps. If zoomed past
the 200mm setting, the camera lens may contact the ports lens and
“lock-up” the camera functions. If this occurs, turn the camera off
and then on again to reset.
7. Check the Picture Size and Quality.
NOTE: When using “M” manual mode, use the UP arrow button
on the menu pad to toggle between aperture and shutter speed
function, and use the rear dial to change settings.
Setting Up Your Housing
Opening the Housing
1. Push the lid snap lock forward and start to lift the curved end away
from the housing.
7
2. Lid snaps are designed to provide enough force to compress the
o-ring for a proper seal. Keep firm pressure against the lid snap
while lifting it away.
Lid Snap Lock
3. Repeat with remaining lid snaps.
4. Remove the housing back.
Inserting the Camera
1. Remove any lanyard or neck strap which may be attached to the
camera.
2. Check to see whether the camera’s lens will fit through the port
opening of the housing. If not, the lens will need to be removed
from the camera body and re-attached AFTER the camera body is
insalled in the housing.
3. Remove the camera mounting plate from the housing.
Camera tripod
socket
Mounting screw
Mounting
Tray
BOTTOM
8
SIDE
FRONT
4. Line the mounting screw up with the camera’s tripod socket. Use
a coin or flat head screwdriver to tighten the mounting plate to the
camera.
5. Pull out on the housing control knobs to move them out of the way.
6. Insert the mounting plate into the slot on the inside bottom of the
housing. Push the camera all of the way forward until the back of
the mounting plate is flush with the back of the housing mount.
7. RAISE the flash, if using! Note: Once the camera is closed in the
housing, the flash CANNOT be raised. DO NOT raise the flash
BEFORE placing the camera in the housing.
Closing the Housing
1. Make sure the o-ring is clean and in its proper location on the back
of the housing. The main o-ring does not require lubricant to make
a seal.
2. Place the back onto the housing front.
3. Make sure no controls or wires are interfering with the o-ring or the
back of the housing.
4. Place each lid snap into the corresponding hook on the housing
back.
5. Push the lid snaps towards the housing until they are flat against
the housing and the lock has engaged. Close opposing lid snaps at
the same time.
6. Check the o-ring seal. The o-ring should form a uniform, solid line
around the back of the housing. There will be a small, even gap
around the housing between the housing back and the housing
front.
Final Check
1. Re-check the o-ring seal. The seal should form an even, solid line
around the back of the housing.
9
2. Turn on the camera and check all control functions.
3. Make sure that the camera can obtain focus and take a photo.
4. Check battery life and open storage space on your memory card.
5. Check the flash, if using.
6. Submerge the housing in a fresh water tank dedicated to
underwater photography equipment. Visually confirm that there are
no signs of water intrusion or a steady stream of bubbles coming
from one of the housing seals.
Entering the Water
1. If possible, we recommend entering the water without your housing
to ensure that you are comfortable and your life-saving equipment
is in working order. Once you are stable, have someone pass your
camera housing to you.
2. Submerge the housing at the surface of the water and visually
confirm that there are no signs of water intrusion or a steady stream
of bubbles coming from one of the housing’s seals. If water does
appear to be entering the housing, point the lens port downward
and return the housing to the surface as quickly as possible. Please
observe all necessary safety precautions. NEVER ascend faster
than accepted safety limits.
3. Use your hand to gently flush away any small bubbles that may be
on the face of the lens port. Bubbles will produce soft focus spots in
your photo or video.
10
Setting Up An External Strobe
About the Built-In Flash
Due to the opaque housing design, the internal “built-in” flash can
only be used to trigger external fiber optic strobes. To shoot flash
photography underwater, an external strobe must be connected to
the housing and then triggered via fiber optic cord. Always extend the
flash BEFORE closing the camera inside the housing.
We recommend attaching an external strobe for the optimal color
and clarity in a wide variety of shooting situations, including daylight
photography.
Attaching a Fiber Optic Cord
1. Check the end of the fiber optic cord to ensure that it is clean and
smooth.
2. Ensure that the fiber optic cord o-ring is in place. This o-ring does
not provide waterproofing, however it does keep the fiber optic cord
in place.
3. Attach one end of the fiber optic cord into one of the fiber optic
ports on the front of the housing. The connector is a press-fit into
the fiber optic port.
Fiber Optic Cord
O-ring
4. Attach the other end of the fiber optic cord to a compatible strobe.
11
5. Set the strobe to the appropriate setting based on manufacturer
recommendations.
6. Turn the camera on and pop up the built-in flash.
7. Turn the strobe(s) on.
8. Take a test photo to ensure that your strobe(s) are functioning
properly.
Maintenance
Post-Dive
1. Rinse the housing in fresh water. Rotate the housing’s controls and
press each button while submerged in fresh water to flush out any
salt or debris to ensure smooth operation on future dives.
2. NEVER leave your housing in the fresh water rinse tank. Collisions
with other peoples’ gear can cause scratches or damage to your
equipment.
3. Stow the housing in a shaded place where it is protected from
impact or overheating. If no shade is available, we recommend
covering the housing with a towel or cloth.
4. Check the memory card capacity and battery life of your camera
and strobe(s). Recharge as necessary.
5. Always re-check o-ring seal after opening the housing.
Travel and Storage
1. Remove the camera from the housing for travel or storage.
2. Check the main housing o-ring.
3. Close the empty housing and submerge in lukewarm fresh water.
While submerged, rotate each control and depress each button to
flush out any salt or debris.
12
4. Remove the housing from water and rinse with running water.
5. Do not rinse the inside of the housing or submerge the open
housing in water. If the inside of the housing needs to be cleaned,
wipe with a clean, slightly damp cloth.
6. Dry the housing with a clean, lint-free cloth.
7. Store in a cool, dry place.
8. Like regulators and other pressure-sensitive equipment,
we recommend careful care and cleaning along with annual
replacement of the factory seals.
Troubleshooting
Water enters the housing
• Re-clean and re-install the main o-ring.
• Take the housing underwater without a camera installed to ensure
that the leaking has been corrected.
Photos are over-exposed (too light)
• Adjust aperture (smaller), shutter speed (faster), or ISO (lower)
setting.
• Move lights(s) farther away from your subject.
• Adjust exposure compensation in the camera.
• Adjust lighting power.
Photos are under-exposed (too dark)
• Adjust aperture (larger), shutter speed (slower), or ISO (higher)
setting.
• Move light(s) farther away from your subject.
• Adjust exposure compensation in the camera.
13
• Adjust lighting power.
Strobe will not fire
• Turn on strobe.
• Make sure that the camera’s flash is set to fire on every photo.
• Check that the fiber optic cord is attached.
Buttons are stuck
• Soak the housing in lukewarm fresh water. Depress each button
several times while the housing is submerged.
• Apply lubricant to the button. Press the button several times to
distribute the lubricant.
Button(s) or control(s) do not line up
• Ensure that nothing is preventing the camera from going into the
housing.
• Push the camera mounting plate forward until it is flush with the
housing base plate.
Camera is not functioning normally underwater
• Ensure that the camera mounting plate is pushed all of the way into
the housing mounting plate.
• Check each housing control while underwater to ensure that
they are disengaged. An inadvertently engaged control may limit
functioning of the camera.
• Check that the zoom control is not engaged.
Backscatter or “snow” in images
• Position strobes or lights farther away from your lens and at a slight
angle.
14
• Avoid using strobes in extremely low-visibility conditions.
Limited Warranty
This Ikelite product is warranted against any manufacturing defects for
a period of two (2) years from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at
its sole discretion, repair or replace such products, and will return to
customer postage paid. All other claims of any nature are not covered.
Except as mentioned above, no other warranty expressed or implied
applies to this Ikelite product.
Service and Repairs
Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or description of the service
request. Always include name, shipping address, email address, and
phone number inside of the package. Send postage paid to:
Ikelite Underwater Systems
Attn: Service Department
50 West 33rd Street
Indianapolis, IN 46208 USA
For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that
the enclosed products were originally manufactured in the USA and
are being returned to the manufacturer for repair service. Value of the
equipment listed for customs purposes should be zero.
15
Contact Us
If you have any questions about your product or need advice on
getting the images you want, please get in touch with us and we’ll do
everything we can to help you capture your unique perspective.
Ikelite Underwater Systems
50 W 33rd St
Indianapolis, IN 46208 USA
(317) 923-4523
ikelite@ikelite.com
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertising