Ikelite | Base with Dual Quick Release Handles for DL and FL Housings | Instruction manual | Ikelite Base for DL and FL Housings Instruction Manual

Ikelite Base for DL and FL Housings Instruction Manual
Base with Left Quick Release Handle for DL and FL
Housings
Product # 4077.67
Base with Dual Quick Release Handles for DL and FL
Housings
Product # 4077.68
About this Product
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product.
Important Information
» The Base with Quick Release Handle(s) is designed primarily
for DL and FL housings, but can be attached to any Ikelite
housing using the hardware included.
» An Anti-rotational Pad is included when attaching the Base to
a Non-Ikelite housing with a single 1/4-20 mount.
» A 1/4-20 threaded mouting point is located in the center of the
Base to allow attachment to a Tripod.
2
Included in the Box
# 4077.01 Left Handle
with Extension
# 4077.02 Right Handle
with Extension (NOT
included with # 4077.67)
# 0399.02 Spacer
# 0399.03 Anti-rotation Pad
Base # 4077.66
Qty. 2 - # 0212.16 1/4” Nylon Washer
Qty. 4 - # 0245.2 3/8” Nylon Washer
Qty. 2 - # 0212.12 1/4” Shoulder Washer for 12-24 Screw
Qty. 2 - # 0212.14 1/4” Shoulder Washer for 1/4-20 Screw
Qty. 2 - # 0213.38 1/4-20 x 3/8” Screw
Qty. 1 - # 0220.2 1/4-20 x 5/8” Screw
Qty. 2 - # 0333.6 12-24 x 1/2” Screw
Qty. 2 - # 0219.5 3/8-16 Hex Nut
Qty. 1 - # 0945.18 Hex Key
3
Contents
About this Product
2
Important Information
2
Included in the Box
3
Attach Base to DL or FL Housing
Attach Base to Compact Housing with 3/8-16 Bolts
Attach Base to Compact Housing with Threaded Mounts
Attach Base to ULTRAcompact Housing with Threaded Mounts
Attach Base to Non-Ikelite Housing with 1/4-20 Threaded Mount
5
6
7
8
10
Limited Warranty
11
Contact Us
12
4
Attach Base to DL or FL Housing
1. Determine the correct thread type for your housing mounts. ALL
white housings use 1/4-20 x 3/8” screws. Most clear and older
housings use 12-24 x 1/2” screws. 1/4-20 screws will not thread into
a smaller 12-24 size mount.
CAUTION: Using the incorrect screws could damage your housing
mounts.
2. Once the correct screws have been selected, place your Ikelite
DSLR housing upside down on a flat surface or on your lap.
3. Line up the 3/8” tray holes with the housing mounts. If the tray is
positioned properly, the Quick Release Buttons will be extending
toward the rear of the housing.
4. Place a shoulder washer in the holes corresponding to the housing
mount holes, with the small end of each washer facing down.
5. With your free hand, insert and rotate the correct screws clockwise
until threaded into the housing mounts. Finish tightening the base
to the housing using a flathead screwdriver. DO NOT overtighten.
1/4” Shoulder Washer 1/4-20
1/4-20 x 3/8” Screw
IKELITE
Quick Release Button
5
Attach Base to Compact Housing with 3/8-16 Bolts
1. Place your Ikelite Compact Housing upside down on a flat surface
or on your lap.
2. Peel protective film off # 0399.02 Spacer to expose adhesive. Place
Spacer over Housing Mounting Bolts with adhesive side facing up.
Protective Backing
(peel off before use)
3. Line up the base holes with the 3/8” housing bolts. If the tray is
positioned properly, the Quick Release Buttons will be extending
toward the rear of the housing.
3/8” Nylon Washer
Quick Release Button
6
3/8-16 Hex Nut
4. Slide Tray into position over the Spacer and press firmly for a
couple seconds. This will allow the Spacer to cling to the base.
5. With your free hand, slide the 3/8” nylon washers over the Housing
Mounting Bolts and tighten base using both 3/8-16 Hex Jam Nuts.
Finish tightening the base to the housing using a 9/16” open end or
socket wrench. DO NOT overtighten.
Attach Base to Compact Housing with Threaded Mounts
1. Determine the correct thread type for your housing mounts. ALL
white housings use 1/4-20 x 3/8” screws. Most clear and older
housings use 12-24 x 1/2” screws. 1/4-20 screws will not thread into
a smaller 12-24 size mount.
CAUTION: Using the incorrect screws could damage your housing
mounts.
2. Once the correct screws have been selected, place your Ikelite
Compact Housing upside down on a flat surface or on your lap.
1/4” Shoulder Washer
1/4-20 x 3/8” Screw
Quick Release Button
7
3. Line up the 3/8” tray holes with the housing mounts. If the base is
positioned properly, the Quick Release Buttons will be extending
toward the rear of the housing.
4. Place a shoulder washer in the holes corresponding to the housing
mount holes, with the small end of each washer facing down.
5. With your free hand, insert and rotate the correct screws clockwise
until threaded into the housing mounts. Finish tightening the base
to the housing using a flathead screwdriver. DO NOT overtigthen.
Attach Base to ULTRAcompact Housing with Threaded Mounts
1. Determine the correct thread type for your housing mounts. ALL
white housings use 1/4-20 x 3/8” screws. ALL clear and older
housings use 12-24 x 1/2” screws. 1/4-20 screws will not thread into
a smaller 12-24 size mount.
CAUTION: Using the incorrect screws could damage your housing
mounts.
2. Once the correct screws have been selected, place your Ikelite
ULTRAcompact Housing upside down on a flat surface or on your
lap.
8
3. Line up the 3/8” tray holes with the housing mounts. If the Base is
positioned properly, the Quick Release Buttons will be extending
toward the rear of the housing.
1/4” Shoulder Washer
1/4-20 x 3/8” Screw
Quick Release Button
4. Place two shoulder washers in the holes corresponding to the
housing mount holes, with the small end of each washer facing
down.
5. With your free hand, insert and rotate the correct screws clockwise
until threaded into the housing mounts. Finish tightening the base
to the housing using a flathead screwdriver. DO NOT overtighten.
9
Attach Base to Non-Ikelite Housing with 1/4-20 Threaded Mount
Protective Backing
(peel off before use)
1. Remove the protective backing from the Anti-rotational Pad.
2. Line up the pad hole with the larger non-threaded center base hole
and place the adhesive side down on the base.
3. Line up center base hole with the housing mount hole. If the base is
positioned properly, the Quick Release Buttons will be extending
toward the rear of the housing.
1/4” Nylon Washer
Quick Release Button
10
1/4-20 x 5/8” Screw
4. With your free hand, insert and rotate the 1/4-20 X 5/8” screw
clockwise until threaded into the housing mount. Finish tightening
the base firmly to the housing using a flathead screwdriver. DO
NOT overtighten.
Note: Since the housing base is designed for Ikelite Housings, any
excessive pressure applied to either side of a Non-Ikelite housing
may cause slight rotation or movement of the housing on the base.
Also, make sure the screw does not bottom out on the housing
bottom causing damage. Additional nylon washers should be used
if necessary.
Limited Warranty
This Ikelite product is warranted against any manufacturing defects for
a period of one (1) year from the original date of purchase. To obtain
warranty service, the product must be returned to Ikelite postage paid.
Ikelite will, at its sole discretion, repair or replace such products, and
will return to customer postage paid. All other claims of any nature
are not covered. Except as mentioned above, no other warranty
expressed or implied applies to this Ikelite product.
11
Contact Us
If you have any questions about your product or need advice on
getting the images you want, please get in touch with us and we’ll do
everything we can to help you capture your unique perspective.
Ikelite Underwater Systems
50 W 33rd St
Indianapolis, IN 46208 USA
+1 (317) 923-4523
ikelite@ikelite.com
© 2017 Ikelite Underwater Systems
4077.67_4077.68_Base_Handle(s)_1-1017
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising