Posiflex | WB-4200 | User manual | Posiflex WB-4200 User Manual

Posiflex WB-4200 User Manual
WB-4200
Wall Mounting Bracket
Installation Guide
Rev.: A0
P/N: 14520901020
KIT NAME: WB-4200
WB-4200 wall mount bracket - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 pcs
Self tapping screw 3.5φ-16L (P/N: 14520900010) For TX-4200/4200E Wall
mount use- - - - -- - - - -- - - - -- - - - -- - - - -- - - - -- - - - -- - - - -- - - - - 4 pcs
Shoulder screw (P/N: 14520900010 applied on back of main unit if this kit
ordered with it) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -4 pcs
Plastic Cotter (P/N: 10241000021)-- - - - -- - - - -- - - - -- - - - -- - - -- - 4 pcs
Washer φ4.2* φ12*1mm(Ni) (P/N: 10410421210) For RT Series Wall
mount use………………………………….……………………………4 pcs
Installation guide - - - - -- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1 copy
ABOUT THIS PRODUCT
This WB-4200 wall mounting kit is applicable for wall mount application
of main unit of TX-4200/4200E and RT series. With this robust kit, TX4200/4200E Series is so versatile that it can be used as a full fledge POS
Box, a Kitchen Video System (KVS) controller and a Digital Signage
controller.
INSTALLATION PROCEDURE
FOR WALL MOUNTING
This bracket kit supports wall mounting of TX-4200/E, separately packaged
at delivery. However, this kit is ordered separately from the main unit and
to be installed on a system initially. Some preparations must be taken on the
main unit and then come back for the operation of wall mounting.
Please kindly follows steps below to fix the WB-4200 wall mount with
the main unit TX-4200 series on the wall.
This bracket can be fit to a supportive mechanism compliant to standard
with 75 mm pitch in vertical direction &146 mm pitch in horizontal
direction.
Page 1
Step A): Select a flat surface on wall of adequate strength and
thickness and with proper ventilation and space condition.
Step B): To apply the plastic cotters, please drill 4 holes in
rectangular layout as marked in the template that gives a rectangular
drill pattern of 5.75” or 146 mm wide (horizontal) and 2.95” or 75 mm
high (vertical). Hole diameter should be 1/4” or 6.35 mm each. Hole
depth should be at least 1 and 3/8” or 35 mm.
Step C): Apply the 4 plastic cotters into the drilled holes then 4 selftapping 3.5φ-16L screws through the arrowed holes in bracket to hold
it firmly on the wall.
Self-tapping
screw
Step D): Aim the 4 heads of shoulder screws into the 4 arrowed holes
(75mm x 75mm VESA mount pitch) on the TX-4200 series main unit.
Page 2
Step E): Hold the main unit then slide down the winding grooves in
the wall mount bracket. Apply some downward force to the main unit
so that it holds firmly in the bottom of the grooves.
TX-4200 Series
Main Unit
Selftapping
screw
Shoulder
Screw
Page 3
Please kindly follows steps below to fix the WB-4200 wall mount with
the main unit RT series on the wall.
Step A): After taking off the back cover of the RT series terminal,
please remove the mylar sheet as shown in the below picture.
Step B): After removing the mylar sheet, please take off the plastic
VESA insert as shown in the below picture.
Page 4
Step C): Take off the other plastic VESA insert.
Step D): Place the back cover back to the RT series terminals. Insert
the 3.5φ-16L screws into the washer in the order as shown in the
below picture, and then fix the four 3.5φ-16L screws with washer to
the wall VESA hole.
Page 5
Step E): Fix the wall mount bracket on the wall as shown in the below
picture.
Step F): Mounting the RT series terminal on the wall mount bracket.
Page 6
Template WB-4200 Overall View
Drill at center
of dashed cross
Drill at center
of dashed cross
Template for
WB-4200
Each hole should be
at least1 + 3/8” or 35
mm deep.
THIS
SIDE UP
Use drill tip of diameter1/4”
or 6.25 mm.
Drill at center
of dashed cross
Drill at center
of dashed cross
Page 7
<MEMO>
Page 8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising