Posiflex | IO-200 | User manual | Posiflex IO-200 User Manual

Posiflex IO-200 User Manual
IO-200
I/O Box
Installation Guide
Package Contents




IO-200 I/O Box………………...(1)
Mounting Screw (φ4-16L)…...(4)
Plastic Anchor…………….……(4)
User Manual...………................(1)
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply
with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the
user at his own expense will be required to take whatever measures to correct
the interference.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
16940904010 Ver. A0
http://www.posiflex.com
1
Views of the IO-200
Top View
Mounting Screw Hole
Mounting Screw Hole
Front View (Connect to Peripherals)
DB9 COM Port
24V Powered USB Port
LAN Port
VGA OUT
DP OUT DC IN
CR Port
DB9 COM Port
USB 3.0 Ports
12V Powered USB Port
Rear View (Connect to POS Terminal)
DC OUT
DP-IN USB3.0-IN
(with screw lock)
VGA-IN
2
Mounting under a Table
IO-200 is designed to be mounted under a table. Please follow the instruction
below.
Put IO-200 system under the table, then
Table
screw in the mounting holes. Same on the
other side.
Installing Drivers
Before using the I/O box, download first the USB-to-COM, USB-to-LAN, and
virtual COM drivers.
Please visit Posiflex official website (http://www.posiflex.com/englobal/Download/download) to download the drivers.
Then, follow the step-by-step instructive messages to complete the driver
installation. After completion of the driver installation, restart your POS
terminal.
Setting the Commands for CR Port (Cash Drawer) of I/O Box
CMD 1 : Open CR1:0x07
CMD 2 : Open CR2:0x17
CMD 3:Read CR1 Status (Open or Close):0xC1 Feedback:’O’ or ’C’
CMD 4:Read CR2 Status (Open or Close):0xC2 Feedback:’O’ or ’C’
3
Specifications
Front I/O ports
Rear I/O ports
Power source
Dimensions
Weight
Operating condition
Storage condition
Regulatory
Accessories
(Optional)
DP x 1
VGA x 1
Giga LAN x 1
USB3.0 x 6
CR port x 1
RS-232 DB-9 serial port x 3
12V powered USB port x 1
24V powered USB port x 1
DC Jack(4-pin, 12V power input) x 1
DP x 1
VGA x 1
USB3.0(with screw lock) x 1
DC jack(4-pin, 12V power output) x 1
12V/150W
243 x 80 x 45 mm
715g
0°C - 40°C, 20%RH - 90%RH
-20°C - 70°C, 10%RH - 90%RH
FCC/CE
USB 3.0 cable x 1
DP cable x 1
VGA cable x 1
DC power cable x 1
※ The product information and specifications are subject to change
without prior notice. To get the detailed information on IO-200, please
check this model from Posiflex Global Website
(http://www.posiflex.com/en-global/Download/download).
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising