Posiflex | PS-3416/3416E | User manual | Posiflex PS-3416/3416E User Manual

Posiflex PS-3416/3416E User Manual
PS-3416/3416E
Fanless LCD Touch Terminal
User Manual
Package Contents





Fanless LCD touch terminal (x1)
Power adaptor
(x1)
Power cord
(x1)
User Manual
(x1)
Recovery DVD
(x1)
(for pre-loaded OS model only)
This system meets industry & government requirements and applicable
standards.
※ The appearance of the product may be somewhat different from that of
the actual product, so the appearance of this product should be based
on that of physical products. The contents in this manual may be
updated at any time without prior notice.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions manual, may cause
interference to radio communications. It has been tested and found to comply
with limits for a Class A digital device pursuant to subpart J of Part 15 of FCC
Rules, which are designed to provide reasonable protection against
interference when operated in a commercial environment. Operation of this
equipment in a residential area is likely to cause interference in which case the
user at his own expense will be required to take whatever measures to correct
the interference.
This is a class A product. In a domestic environment this
product may cause radio interference in which case the user
may be required to take adequate measures.
CAUTION
RISK OF EXPLOSION IF BATTERY IS REPLACED
BY AN INCORRECT TYPE
DISPOSE OF USED BATTERIES ACCORDING
TO THE INSTRUCTIONS
13120901020 Ver. B0
http://www.posiflex.com
1
Terminal from shipping mode to operation mode
In consideration of proper packaging, before shipping, the
terminal is folded, staying in shipping mode. Thus, when
receiving the product, you will find that the terminal is well
folded, as shown below.
Before operating this terminal, unfold it and make this terminal
rise in operation mode by referring to the following steps. Here,
an equivalent model with GEN 7 base is taken below for example.
1. Firstly, lift this terminal gently to
make it to be unfolded.
2. Overturn this terminal in the
direction as indicated by the arrow
in the right figure.
2
3. Place this terminal on a flat table.
4. Tilt this terminal to a degree in the direction as indicated by
the arrow below.
Terminal from operation mode to shipping mode
To fold this terminal, refer to the following steps. Here, an
equivalent model with GEN 7 base is taken below for example.
1. Remove the cable cover.
2. Carefully hold the lower rim of the display.
3
3. Push the base-folding lever in the direction as indicated by the
arrow below (1). Then, the display will be loosen and go
down (2).
2
1
4. When the display goes down to a degree, loose the basefolding lever, as shown in the direction as indicated by the
arrow below.
5. Then, gently tilt the display in the direction as indicated by
the arrow below until the display is well folded.
4
6. Put back the cable cover.
Views of the PS-3416/3416E
Front View
P-CAP Touch Panel
LED Indicator
Gen 7E Base
Rear View
Rear I/O Cover
HDD Cover
2nd Display Screw Hole
Hinge for LCD
Neck Cover
Cable Cover
Cable Exit
5
Left Side View
Right Side View
Power Button
Brightness
Adjustment Button “+”
MSR Port Cover
Brightness
Adjustment Button “-”
Bottom View
Bottom I/O Cover
View of I/O Interface
Top I/O Ports
Rear I/O Ports
1
1
2
3
COM4 Port
3
4
Parallel (LPT) Port
Connector
2 USB 2.0 Port
4 PS/2_KB Pin Header
※ The top I/O ports are provided for COM-based and USB-based peripheral
devices, for example, customer display.
6
Bottom I/O Ports
1
2
4
3
5
6
1
RJ45 LAN Port
2
USB 2.0 Port
3
VGA Port
4
COM Port
(COM3/COM2/COM1)
5
RJ11 Cash Drawer Port
6
12VDC-IN Power Jack
Installing Optional Upgrade Kits and Peripherals
PS-3416/3416E can work with multiple optional upgrade kits and
peripheral devices, such as magnetic stripe reader (MSR), LCD
monitor, cash drawer and the like.
Before installing an optional upgrade kit and/or peripheral device,
make sure that the system is powered off and the external power
source is removed from the POS box to prevent electric hazard!
Failure to follow the warning description will void the product
warranty!
For the detailed instruction, refer to each of the user manuals of
the optional upgrade kits and peripheral devices.
7
Connecting Power Adapter and I/O Cables
Before connecting power adapter and I/O cables to the I/O ports
of PS series terminal, please route and arranging the cables. Refer
to the following step-by-step instruction of cable routing and
arrangement for the details. Here, an equivalent model with GEN
7 base is taken below for example.
1. Press the circled section of the
cable cover with your thumb.
2. Pull out the cable cover.
Pull out
3. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
8
4. Determine that the terminal is
tilted to the end, as shown in the
right figure.
5. Press the circled section with two
thumbs and pull by force the two
sides of the locking hook with two
forefingers as indicated by the
arrow.
6. Remove the neck cover from the
base stand.
7. Tilt the terminal slightly at a little angle in the direction as
shown by the arrow, making cables easily pass through the
cable passage.
Cable Passage
9
8. Make the connector, which will be connected to the I/O port
of the terminal, pass through the cable passage of base stand.
9. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
10. Remove the bottom I/O cover with
your forefinger inserting the
middle hole of the cover.
11. Connect the connector of the
power adapter to the 12VDC-IN
power jack.
10
12. Cover the bottom I/O interface and gather the I/O cables to
the circled cable arrangement area, as shown below.
13. Push and tilt the terminal to the
end in the direction as shown by
the arrow.
14. Arrange well the I/O cable located
at the area of neck cover.
15. Shield the I/O cable arrangement area on the neck of the base
stand with the neck cover.
11
16. Shield the I/O cable exposure area with the cable cover.
Powering ON the PS-3416/3416E
After connecting the power cable to the power jack
of the terminal, press the power button to power on
the terminal. To power it off, press the power
button again.
Once powering off the system, if you want to
power it on again, please wait at least 3 seconds.
If the system hangs due to a reason, such as software resource
conflict, please press and hold the power button for over 10
seconds to forcedly shut down the system.
Power LED Indicator
LED status indicator, which is located at the lower right side of
the LCD panel, is mainly responsible for notifying users of the
current system status by emitting various LED signals. The table
provided below shows all the possible LED status as a quick
reference.
LED
POWER
Status
Solid blue
Solid orange
Description
System power ON
System standby
12
Installing an Operating System
This product is highly professional equipment. Therefore, we do
NOT encourage you to install any operating system into this
machine without professional assistance. We shall not be
responsible for any technical support to questions on this aspect.
We suggest that you contact your dealer for OS installation.
Operating System Recovery
For the PS-3416/3416E main system preloaded with an operating
system on HDD or SSD, We provide a recovery DVD shipped
with the main system for the preloaded operating system. The
system integrator shall take care of software restoration after the
OS is recovered.
If you plan to recover your operating system, we do NOT
encourage you to recover any operating system. Please contact
your service center for operating system recovery.
Operation Environment
This terminal must NOT be operated in an environment with
restricted ventilation. There must be at least 25 mm air clearance
around any top or side ventilation holes with free flow of air
around the unit at all times for system operation.
13
Specifications
Processor
PS-3416:
Intel® Celeron J1800, 2C, 2.41GHz/2.58GHz
(Burst), 1M Cache
PS-3416E:
Intel® Celeron J1900, 4C, 2.00GHz/2.42GHz
(Burst), 2M Cache
System
Memory
SO-DIMM x 1, DDR3L
Storage Device
SATA x 1 + mSATA x 1
Power Supply
12V/40W
(upgrade to 60W or higher when required)
OS support
Windows 7 / POSReady 7 /
Windows Embedded 8.1 Industry /
Windows 10 IoT 64-bit / DOS /
Linux per request
LCD
Bezel-free TFT LCD
Resolution
1024 x 768
Touch
Projected-capacitive touch
Serial Port
4, 3 x DB9 on bottom I/O plate + 1 x RJ50 on top I/O
plate, 5V/12V support on all COM ports
Parallel Port
1, via optional conversion cable
Standard USB
Port
5, 4 on bottom I/O plate + 1 on top I/O plate
LAN Port
10 / 100 / 1000 Mb x 1
Display Port
VGA x 1, 12V support for Posiflex monitors
CR Port
1, control 2 CR via optional Y-cable
PS/2 Port
Pin header inside service window
Audio
Buzzer only
Base Stand
7th generation foldable base stand
Power Supply
12V/40W
Operating
Condition
0°C - 40°C, 20%RH - 90%RH (Equipped with
HDD);
0°C - 50°C, 20%RH - 90%RH (Equipped with SSD)
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
System
Configuration
Display & Touch
I/O & Expansion
Environmental
※ The product information and specifications are subject to change without
prior notice. To get the detailed information on the PS-3416/3416E,
please check this model from Posiflex Global Website.
14
<MEMO>
15
<MEMO>
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising