Posiflex | TX-5300 | User manual | Posiflex TX-5300 User Manual

Posiflex TX-5300 User Manual
TX-5300/5300E/5500/5500E
Fanfree POS Box
User Manual
TX-5300E/5500E
TX-5300/5500
Package Contents





TX-5300, TX-5300E,
TX-5500 or TX-5500E POS box………………..……...(x1)
12VDC/80W power adaptor (TX-5300/5500)
or 12VDC/150W power adaptor (TX-5300E/5500E).….(x1)
Power cord………………………………………….…...(x1)
Wall-mount bracket (optional)……………………….….(x1)
User manual……………………………………………..(x1)
14550901010 Ver. A0
http://www.posiflex.com
1
Views
Front View of TX-5300/5500
Power Status LED Indicator
Power Button
USB 2.0 Port
Storage Status LED Indicator
Front View of TX-5300E/5500E
Power Button
Power Status LED Indicator
Storage Status LED Indicator
Powered USB Port
Top View of TX-5300/5300E/5500/5500E
Heat-Dissipation Fins
2
Bottom View of TX-5300/5300E/5500/5500E
Rubber Pad
Rubber Pad
Service Door
Rear I/O Ports
TX-5300/5300E/5500/5500E
1
3
4
6
9
8
2
5
7
1
USB 3.0 port
2
RJ45 LAN port
3
VGA port
4
RJ11 cash drawer (CR) port
5
LPT port
6
HDMI port
7
COM port
8
12VDC-IN power jack
9
Mic-in / line-out combo jack
3
Connecting Power Adapter and I/O Cables
To have the terminal ready for operation, please connect the
connector of power adapter and all of the connectors of required
I/O cables respectively to the 12VDC-IN power jack and
appropriate I/O ports. Please make sure that each of the cables is
fully connected to the correct port. Damages due to incorrect
connection or orientation are not covered by product warranty!
Some cable connectors like the connectors of LAN or cash
drawer (CR) cables have to be gently inserted until a click is
heard. It is recommended that the I/O ports, such as COM port,
parallel port, and VGA port, should be screwed after the I/O
cable connectors are completely connected. And please make
sure that each connector has to be connected to the right
peripheral device in the right way.
CAUTION: On doing insertion or extraction of a cable
connector, please always hold the connector head itself
instead of pulling the cable wire. Doing this could damage the
cables and ports, which is considered as an artificial damage
and is not covered by the warranty.
Note: The COM ports of TX-5300/5300E/5500/5500E do not
supply power by default. To make the COM ports supply
power, you can set up the COM ports through the
dedicated settings listed in the table below.
BIOS Setting
Jumper Setting
TX-5300/5300E/5500/5500E
COM1/2/3/4
COM5/6
5VDC
12VDC
5VDC
12VDC
V
V
V
V
VGA
12VDC
V
The VGA port of TX-5300/5300E/5500/5500E can supply
+12VDC power through system BIOS setting for Posiflex
LCD monitor. Nevertheless, except Posiflex VGA monitor,
do not connect any other monitor to this port with VGA
power enabled.
4
Installing Optional Peripheral Devices
Posiflex TX-5300/5300E/5500/5500E can work with multiple
optional peripheral devices, such as LCD monitor, cash drawer
and the like.
Before installing an optional peripheral device, make sure that the
system is powered off and the external power source is removed
from the POS box to prevent electric hazard! Failure to follow the
warning description will void the product warranty!
For the detailed instruction, refer to each of the user manuals of
the optional peripheral devices.
Installing an Optional Second Storage (SSD)
The TX-series system is provided with a second storage bracket
for you to install an optional second storage. To avoid users from
damaging the main board of the system, it is highly
recommended that the optional second storage installation is
implemented by professional technicians.
Installing a Memory Upgrade Module
The TX-series system is provided with two DRAM slots for you
to expand or replace memory. Before shipping, one memory has
been inserted into one socket of the main board. To expand or
replace memory, follow the two steps below.
1. Loosen and remove the screw from the
service door.
2. Remove the service door.
To avoid users from damaging the main board of the system, it is
highly recommended that the memory expansion and replacement
are implemented by professional technicians.
5
Mounting the TX-5300/5300E/5500/5500E on the
Wall (Optional)
1. Fix the wall mount bracket onto the wall
by using attached plastic anchors and
screws.
2. Do spiral insertion of 4 screw bolts into
the 4 screw bolt holes.
3. Lineup the 4 screw bolts to be inserted
into the 4 tracks. Then slide downwards
the system along the track until a click
sound is given for completely mounting
the system with the bracket on the wall.
For detailed installation description, please refer to the WB-4200
bracket installation guide.
Powering ON/OFF the POS Box
Power ON TX-5300/5300E/5500/5500E
Press down the power button to power on the TX5300/5300E/5500/5500E.
Power OFF TX-5300/5300E/5500/5500E
In most cases, push the power button again to
power the system off. However, if the POS box
halts for unknown reasons, please be advised to
hold the power more than 10 seconds to initiate a
forced shutdown.
6
Status LED Indicator
There are two status LED indicators, power status LED indicator
and SSD status LED indicator, on the front side of the TX5300/5300E/5500/5500E. After powering ON the POS system,
you can read the system operation status from the power and SSD
status LED indicators. The LED status is described below.
LED
POWER
SSD
Status
Solid green
Solid red
Flash green
Description
System power ON
System standby
Data access
Installing an Operating System
This product is highly professional equipment. Therefore, we do
NOT encourage you to install any operating system into this
machine without professional assistance. Posiflex Technology,
Inc. shall not be responsible for any technical support to
questions on this aspect. We suggest that you contact your dealer
for OS installation.
Operating System Recovery
For the TX-5300/5300E/5500/5500E main system preloaded with
an operating system, Posiflex provides a recovery DVD shipped
with the main system for the preloaded operating system. The
system integrator shall take care of software restoration after the
OS is recovered.
If you plan to recover your operating system, we do NOT
encourage you to recover any operating system. Please contact
your service center for operating system recovery.
Operation Environment
This terminal must NOT be operated in an environment with
restricted ventilation. There must be at least 25 mm air clearance
around any top or side ventilation holes with a free flow of air
around the unit at all times for system operation.
7
Specifications
TX-5300
CPU
Chipset
TX-5300E
TX-5500E
Intel Coffee Lake-S CPU Core-i3
H310
Q370
Memory
OS
TX-5500
Intel® Coffee Lake-S CPU Core-i5,
Core-i7
DDR4 SO-DIMM x2, Max. 16GB
Windows 10 IoT / Linux (by request)
VGA Port
VGA(DB15 pin) x 1 , supporting +12V/2.5A
HDMI Port
HDMI x 1
DB9 pin x 4 for COM1 ~ COM4
COM5 & COM6 pin header through service door
Serial Port
Ethernet Port
5 x RS-232(COM1, COM3~COM6) + 1 x RS-232/422/485(COM2)
10/100/1000 Mb x 2
Wireless Com.
Optional, 802.11 b/g/n with integrated antenna, M.2 module
Power Supply
12VDC power adaptor, 80W
12VDC power adaptor, 150W
Parallel Port
CR Port
USB Port
Audio Port
Storage
RAID Support
vPro Support
Parallel port(DB26 pin) x 1
CR port x 1, controlling 2 cash drawers
TX-5300/5500:
USB3.0 x 4 (on the rear I/O side)
USB2.0 x 3 (on the front side)
TX-5300E/5500E:
USB3.0 x 4 (on the rear I/O side)
24V/2A Powered USB port x 1 (on the front side)
12V/1A Powered USB port x 2 (on the front side)
MIC-in / line-out x 1 & 2W internal speaker
SATA x 2
M.2 2280 x 1 (SATA only)
SATA x 2
M.2 2280 x 1 (PCIe or SATA)
N/A
Yes, supporting for at least two
SSDs (Q370 only)
N/A
Yes (Q370 only)
Extension Slot
M.2 2230, reserved for M.2 WIFI w/external di-pole antenna
Power Switch
Soft switch
Mechanical
Installation
Desktop or wall mount, VESA mount 75 x 75
Wall-Mount
Bracket
Optional, WB-4200
8
TX-5300
LED Indicator
TX-5300E
TX-5500
TX-5500E
Front Panel:
Power on/ standby, bi-color LED indicators and storage LED indicator
Rear Panel:
Ethernet link LED on Ethernet connector
COM 5/6
Extension
Cable
Optional for COM 5/6 pin header inside service door
Operating
Condition
0°C - 40°C, 20%RH - 90%RH (Equipped with HDD);
0°C - 50°C, 20%RH - 90%RH (Equipped with SSD)
Storage
Condition
-20°C - 70°C, 10%RH - 90%RH
※ The product information and specifications are subject to change without prior notice.
To get the detailed information on TX-5300/5300E/5500/5500E, please check this model
from Posiflex Global Website (http://www.posiflex.com/en-global/Download/download).
9
<MEMO>
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising