Posiflex | TM/LM-401X | User manual | Posiflex TM/LM-401X User Manual

Posiflex TM/LM-401X User Manual
TM-4010/LM-4010
TM-4011/LM-4011
POS Monitor User Manual
Package Contents

9.7” LM-4010 or 9.7” TM-4010
or 10.1” LM-4011 or 10.1” TM-4011
POS Monitor ……………………… (x 1)
Mounting Kits ………………....…...(x 1)
User Manual………………………...(x 1)


Views of TM-4010/LM-4010/TM-4011/LM-4011
Front View of TM/LM-4010
Camera (Optional)
9.7” LM-4010 LCD Panel
9.7” TM-4010 P-CAP Touch Panel
Front View of TM/LM-4011
Camera (Optional)
10.1” LM-4011 LCD Panel
10.1” TM-4011 P-CAP Touch Panel
Rear View
Front Cover for
Mounting Bracket
19640901020 Ver. B0
http://www.posiflex.com
1
Mounting your Monitor to RT-series POS Terminals
The following instructions are provided to help you mount your TM/LM-4010
or TM/LM-4011 to Posiflex RT-series POS terminals. During installation,
please ensure the terminal is properly turned off and disconnected from the
power sources to avoid potential hazards.
1.
Tile the screen of your RT-series terminal to
the most upright position.
2.
Remove the system cover by holding down
the release levers at the bottom of the cover
and then pulling the cover outwards.
3.
Take the monitor out of package box, and remove the front cover for
mounting bracket.
4.
Tear off the release liner from the protective
strip which is clipped onto the mounting
bracket.
2
5.
Lift the monitor, align the two screws holes located on the mounting
bracket with those on the top of the system compartment of RT-series
terminals and then secure the monitor with two fixing screws.
6.
After ensuring the monitor is well mounted to RT-series terminal, push
back the front cover for the mounting bracket of TM/LM-4010 or
TM/LM-4011.
7.
Tile the monitor screen all the way up.
8.
Well insert the cable to the internal VGA port from the mainboard of
RT-series terminal, and tuck the extra cable inside the system
compartment.
3
9.
Place back the sytem cover to close the system
compartment of RT-Series terminal.
10.
Tile the monitor screen to your desired angle.
While setting up the tilting adjustment, be
careful NOT to press on the LCD panel.
Identifying your Monitor as Secondary Touchscreen Monitor
in Extended Mode
In the following section the related descriptions will be offered to help you set
up TM series as the extended monitor when you attempt to extend the desktop
across multiple monitors
For TM-4010/4011 Models with P-CAP Touchscreen
If your monitors are TM-4010/TM-4011 models, you may configure the
display settings from Control Panel in Microsoft Windows to identify the
monitor as the secondary touchscreen monitor. Please go through the below
steps to complete configuration.
1.
Make sure that the monitor is well connected to your POS terminal.
2.
Go to Control Panel>Display Settings, change your display settings to
extended mode.
3.
Go to Control Panel, and then click on
Tablet PC Settings item.
4.
In Tablet PC Settings dialogue box, click
on Setup button.
4
5.
Following the instruction shown on the screen, click on the screen that
you want to identify as the primary touchscreen display.
6.
Press Enter button to proceed the configuration.
7.
Click on the screen you want to use as the secondary touchscreen
display.
Powering ON/OFF your Monitor
To start up TM-4010/LM-4010/TM-4011/LM-4011, please make sure that the
monitor is well connected to POS terminals and electricity is supplied to the
monitor through POS terminal.
Installing Drivers
Please visit Posiflex official website to download and install the related drivers.
http://www.posiflex.com/en-global/Download/download)
5
Setting up Display Resolution for Your Monitor
The below chart defines the list of recommended display settings for
TM/LM-4010 or TM/LM-4011. Improper display configuration will prevent
the monitor from properly displaying the image and lead to a warning message
of “out of range” prompted on the screen.
9.7” TM/LM-4010
Display Resolution Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 400
37.9
70
640 x 480
31.5
37.9
37.5
60
72
75
720 x 400
37.9
70
800 x 600
35.1
37.9
48.1
46.9
56
60
72
75
1024 x 768
48.4
60
10.1” TM/LM-4011
Display Resolution Horizontal Frequency (KHz)
31.5
640 x 480
37.9
37.5
37.9
800 x 600
48.1
46.9
Refresh Rate (Hz)
60
72
75
60
72
75
1024 x 768
48.4
60
1280 x 720
45.0
60
1280 x 800
49.7
60
6
Specification
TM-4011
Display
LCD Panel
Resolution
Active Area
LM-4011
10.1" TFT LCD
1280(H) x 800 (V)
216.96mm (H) x
135.60mm (V)
R.G.B. Vertical Stripe
TM-4010
LM-4010
9.7" TFT LCD
1024(H) x 768 (V)
196.61mm (H) x
147.46mm (V)
Pixel
Arrangement
Viewing
85/85/85/85 degree
70/60/70/70 degree
Angle
(U/D/L/R)
(U/D/L/R)
Contrast Ratio 800 : 1
500 : 1
Response time 25ms
20ms
Brightness
400 cd/m2
350 cd/m2
Display
VGA
Interface
Power Supply 12V from Posiflex terminal VGA Port
Touch
Touch type
P-CAP
N/A
P-CAP
N/A
Interface
USB
N/A
USB
N/A
※ The product information and specifications are subject to change without
prior notice. To get the detailed information on TM-4010/LM-4010/TM4011/LM-4011 please check this model from Posiflex Global Website
(http://www.posiflex.com/en-global/Download/download).
7
<MEMO>
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising