Posiflex | CD-3200/3201 | Quick Setup Guide | Posiflex CD-3200/3201 Quick Setup Guide

Posiflex CD-3200/3201 Quick Setup Guide
CD-3200U/R & CD-3201U/R
2D Image Scanner
Quick Setup Guide
Package Contents
CD-3200U/3201U

CD-3200U/3201U 2D image scanner

ST-8000 scanner holder stand (Optional)

USB cable

Quick setup guide for CD-3200U/R
CD-3200R/3201R

CD-3200R/3201R 2D image scanner

ST-8000 scanner holder stand (Optional)

RS-232 cable

Quick setup guide for CD-3200U/R
18160900030 Ver. B0
http://www.posiflex.com
1
Product Overview
Front View
Rear View
Scan
window
Status LED
Trigger Button
Scanner Maintenance
The scanner is designed for long-term trouble-free operation and rarely
requires any maintenance. Only an occasional cleaning of the scanner window
is necessary in order to remove dirt and fingerprints.
Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to
avoid the scan window from being scratched and damaged. The scan window
can be cleaned while the scanner is running.
The standard interface cable is attached to the scanner with a 10-pin modular
connector. When the connector is properly seated, it is secured in the scanner
by a flexible retention tab. The cable is designed to be field replaceable.
Replacement cables can be obtained from your authorized distributor. To
replace the cable, take the following steps.
1. Make sure the power of both the host terminal and the scanner is powered
off.
2. Disconnect the old scanner cable from the host terminal.
3. Press down the retention tab, and gently pull out the cable.
4. Insert the new interface cable into the bottom of the scanner until it clicks.
Then, plug the new cable into the host.
LED Indication
Status
Red LED flashes one time
Blue LED flashes one time
Explanation
Power On
Good read
2
Troubleshooting
This section contains information about how to solve problems that you may
encounter when operating the scanner. If a trouble occurs, please refer to the
following diagnostic tips as a mean to solve the trouble. However, before
referring to the tips, make sure that the scanner is installed well. If the problem
remains, contact your dealer.
Problem
The scanner is on but cannot read
any barcode.
Diagnostic Tips
The scanner window is dirty. Clean the scanner
window as described in the Scanner
Maintenance section.
The presented barcode type is not enabled. Use
this guide to tell the scanner to accept that type
of barcode.
The host terminal has disabled the scanner.
Check the setup of host terminal.
The barcode type presented is not supported by
the scanner.
The scanner does not accept more Determine whether the required barcode types
than two or three barcode labels.
are enabled or not.
A stray barcode is sitting somewhere in the
scanner field of view. Remove all barcode labels
from the scanner’s scan volume and try again.
The scanner cannot send the data to the POS
system. Make sure that the scanner is installed
well and your host POS system is ready to
receive data.
A barcode is read by the scanner
The communication settings of the system port
but not accepted by the POS
and the scanner do not match. Adjust the settings
system.
to make them match to each other.
The scanner is not installed well. Contact your
dealer for the proper installation. The software
running on the POS system does not support the
data format of the barcode label.
When a barcode stays close to the Check whether or not you have enabled the
scanner, the barcode cannot be read Manual Trigger mode. If you have enabled this
automatically by the scanner.
mode accidentally, please disable the Manual
Trigger mode by scanning the “Disable trigger”
barcode in the advanced user manual.
3
Programming Codes
Below are some suggestion you need to bear in mind while scanning labels:
1. The barcode labels shown in bold and black are default factory
settings.
2. Please cover the unwanted codes for scanning the specific barcode
required for the programming to prevent confusion in code scanning.
3. Use the user manual downloaded from our global website or taken from
the Information DVD for advanced programming.
4. Two operational modes, Auto Trigger and Manual Trigger, are provided
to help you manage your daily activities more efficiently via CD-3200
series scanners. By default, both of CD-3200U/R and CD-3201U/R are
set to Manual Trigger.
5. While scanning the setup barcode labels provided in the quick guide, you
need to pull the trigger to initiate the decoding process.
Firmware Version
Scan the below barcode label to retrieve the current firmware version.
Firmware Version
User Interface Switch Barcodes with Defaults Setting
Three types of user interface, including RS-232, USB-HID, and USB
virtual COM, are available for you to select. However, after the interface
type is changed, the current settings will be removed and reset to the default
factory settings. If the scanner fails to switch to the desired interface type,
please either re-plug the I/O cable or restart your host terminal, and then
scan the same barcode label to resolve the problem.
RS232
USB-HID
4
USB-VCP
Defaults Barcode Setting
To restore the default factory settings, please select one of three barcodes
listed below.
RS232
USB-HID
USB-VCP
5
Trigger Mode
In general, two trigger modes, Auto Trigger and Manual Trigger, are
offered to help you engage in routine works efficiently using CD-3200
series scanners. While Auto Trigger Mode is activated, the light source of
your scanner will always stay on in order to detect barcode data any time.
On the other hand, with enabled Manual Trigger Mode, the barcode label
will not be decoded unless the trigger button is pulled.
Auto Trigger
Manual Trigger
Auto Trigger Detection Mode
Detection Mode allows you to adjust illumination settings to facilitate the
process of detecting a target code. Through the configurable option, the
status of aiming light can be set to enable or disable. What is more, you
may also arrange the color of illumination in response to the lighting
condition to enhance your scanning performance. However, please be
reminded that Detection Mode only works under the condition that
Trigger mode of CD-3200U/R and CD-3201U/R is set to Auto Trigger.
Regarding each type of available detection modes, the following are related
description for your reference.

Green aiming detection
When a target code falls within the aiming range while the green
aiming light is emitted, the target is detected. It is recommended to
use this mode indoors because the detectability is reduced in an
environment of higher illuminance levels than indoor’s.

Red illumination detection
When a target code falls within the range of the field of view while
the red illumination light is emitted, the target is detected. This mode
can be used in a lighted environment.
6

No illumination detection
A target code is detected without illumination light. The power
consumption can be reduced, but the response of detection will also
be reduced. Ambient light is used for detection in this mode, so this
cannot be used in a dark place while it can be used in a lighted
environment.
Green aiming detection
Red aiming detection
No illumination detection
Enabling of readable codes
Enable UPC
Enable EAN
Enable Code 39
Enable Codabar
7
Enable Interleaved 2of5
Enable Chinese Post Matrix 2of5
Enable POSTNET
Enable MSI/Plessey
Enable UK/Plessey
Enable Code 128
Enable GS1-Databar
Enable GS1-Databar Limited
Enable GS1-Databar Expanded
Enable QR Code
Enable PDF417
8
Setting code specific options
UPC-A, No leading zero, transmit CD
UPC-A, No leading zero, not transmit CD
UPC-A, Leading zero, transmit CD
UPC-A, Leading zero, not transmit CD
Options for UPC-E
UPC-E, No leading digit, transmit CD
UPC-E, No leading digit, not transmit CD
UPC-E, Leading digit, transmit CD
UPC-E, Leading digit, not transmit CD
9
Options for EAN-13 and EAN-8
EAN-13 not transmit CD
EAN-13 transmit CD
EAN-8 not transmit CD
EAN-8 transmit CD
Disable ISBN translation
Enable ISBN translation
Case conversion
No case conversion
Convert to upper case
Convert to lower case
10
Floodlight and aiming options
Disable floodlight
Enable floodlight
Alternating floodlight
Buzzer settings
Disable buzzer
Enable buzzer
Single tone buzzer
High - low buzzer
Low - high buzzer
Buzzer duration 200 msec
11
Buzzer duration 400 msec
Buzzer loudness: Maximum
Buzzer loudness: Loud
Buzzer loudness: Normal
Buzzer loudness: Minimum
Buzzer before transmission
Buzzer after transmission
Disable startup buzzer
Enable startup buzzer
12
Baud rate settings
9600 baud
19200 baud
38400 baud
57600 baud
Data, parity and stop bits
7 data bits
8 data bits
No parity
Even parity
Odd parity
1 stop bit
13
2 stop bits
Handshaking barcode setting
No handshake
Busy/ready
XON/XOFF
ACK/NAK
Flow Control time out 200ms
Intercharacter delay for RS232
No delay
20 ms delay
50 ms delay
100 ms delay
14
Keyboard wedge/USB options
With keyboard
Without keyboard
Keyboard language
US
German
French
Dutch
Japanese
Special options
Do not use numpad
Use numpad
15
Auto numlock mode
No CAPSLOCK mode
CAPSLOCK mode
Auto CAPSLOCK mode
Intercharacter delay for wedges/USB
No delay
Delay = 1
Delay = 3
Delay = 5
Delay = 7
Delay = 9
16
Specifications
CD-3200U/R
Item
Scan method
Number of effective pixel
Image capture speed (*1)
Focal distance
Depth of field (mm)
Characteristics
CMOS area sensor (black
and white)
(H) x (V)
Frame rate
From the front edge of scan
engine
Code 39
Code 128
UPC
PDF417
QR Code
DataMatrix
View angle
Auxiliary light source (LED
x 2)
Light Source for aiming
(LED x 1)
Horizontal
Vertical
Red LED
Peak Wave Length
Directivity angle 2Θ1/2
(*2)
Maximum radiation output
(*3)
Green LED
Peak Wave Length
Maximum radiation output
(*4)
752 x 480 dot
60 fps
130 mm
50~120mm
(Resolution(0.127))
35~190mm
(Resolution(0.25))
70~210mm
(Resolution(0.33))
45~180mm
(Resolution(0.25))
30~210mm
(Resolution(0.33))
30~175mm
(Resolution(0.25))
20~170mm
(Resolution(0.381))
40~145mm
(Resolution(0.31))
Approx. 40.6˚
Approx. 26.4˚
617 nm
60 ˚
*1
The fastest speed of image capture
*2
The reference value extracted from the LED datasheet
*3*4 The reference value extracted from the datasheet
(conditions: 25℃, IF = 140mA)
17
15000 mcd
528 nm
18700 mcd
CD-3201U/R
Item
Scan method
Number of effective pixel
Image capture speed (*1)
Focal distance
Depth of field (mm)
Characteristics
CMOS area sensor
(black and white)
(H) x (V)
Frame rate
From the front edge of scan
engine
Code 39
Code 128
UPC
PDF417
QR Code
DataMatrix
View angle
Auxiliary light source
(LED x 1)
Light Source for aiming
(LED x 1)
*1
Diagonal
Horizontal
Vertical
Color
Color Temperature
Color
Peak Wave Length
The fastest speed of image capture
18
Global shutter
640 x 480 dot
100 fps
120 mm
30~105mm
(Resolution(0.127))
35~200mm
(Resolution(0.25))
65~230mm
(Resolution(0.33))
45~200mm
(Resolution(0.25))
30~270mm
(Resolution(0.33))
15~175mm
(Resolution(0.25))
20~185mm
(Resolution(0.381))
20~150mm
(Resolution(0.31))
Approx. 46.4˚
Approx. 38.0˚
Approx. 26.4˚
Warm white LED
2600 ~ 3700K
Green LED
525 nm
<MEMO>
19
<MEMO>
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising