Posiflex | RT-2000 | User manual | Posiflex RT-2000 User Manual

Posiflex RT-2000 User Manual
RT-2015/2016/2115/2116
Fanless Touch POS Terminal
User Manual
Package Contents




RT-2015 15” fanless touch terminal or
RT-2016 15.6” fanless touch terminal or
RT-2115 15” fanless touch terminal or
RT-2116 15.6” fanless touch terminal (x 1)
Power adapter (x 1)
Power cord (x 1)
User manual (x 1)
16950900010 Ver. A0
http://www.posiflex.com
1
Views of RT-2015/2016/2115/2116
Front View
Camera (Optional)
RT-2015/2016/2115/2116
P-Cap Touch Panel
Base Stand
LED indicator
LED indicator
15” RT-2015/2115
15.6” RT-2016/2116
Rear View
System Back Cover
Attachment Bay
Stand Cover
Cable Exit
Bottom View
Screw for Fire-Resistant
System Back Cover
Release Lever for System Back Cover
2
Left-Side View
Power Button
Brightness Adjustment Button +
Brightness Adjustment Button -
View of I/O Interface of RT-2015/2016
USB 2.0 Ports
DB9 COM Port
CR Port
LAN Port
RJ50 COM Ports
Mini DisplayPort USB 3.0 Port
View of I/O Interface of RT-2115/2116
DB9 COM Port
RJ50 COM Ports
CR Port
USB 2.0 Ports
Mini DisplayPort
3
DC IN
Power
Connector
LAN Port
USB 3.0 Ports
DC IN
Power
Connector
Positioning your POS for a Perfect Viewing Angle
Steady the base with one hand, and then tilt the screen
in the direction shown by the arrow in the figure.
Please do NOT press on the LCD panel while
setting up the tilt angle.
Installing Power Adapter and Cables
The following provides instructions required to install your cables.
1.
2.
Lay the terminal with its rear facing
towards you and tilt the screen all the way
down.
Remove the system back cover.
2.1 If the system back cover is fire-resistant, first locate the screw as
indicated in the figure, and then remove it.
Screw for Fire-Resistant
System Back Cover
2.2
Hold down the release lever at the bottom of
the system back cover and then pulling the
cover outwards.
4
3.
To remove the stand cover from the base, grab the top side of the
cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree
angle, and then (3) slide it in the horizontal direction shown by the
arrow.
1
2
3
4.
Connect the connector of the power adapter
to the DC-IN power jack. If necessary,
properly insert other cables into the correct
port.
5.
Neatly arrange the cables. Locate the cable holder inside the base as
shown in the figure. Push down the lever to release if from the hook,
pass the cable through cable holder, and then press down the lever
again to lock it onto the hook.
Cable holder
6.
Make sure the cord can be held into place and
passed through the cable exit after sliding back
the stand cover.
5
7.
7.1
Place back the sytem back cover. Make sure
it is well locked into place with a click sound.
7.2
For the fire-resistant system back cover, please insert another
screw into the screw hole indicated in the figure, and secure it.
Screw for Fire-Resistant
System Back Cover
8.
Make sure the cable could be pulled out of the
cable exit from the bottom of the base.
Installing Optional Upgrade Kits and Peripherals
RT-2015P/2016P/2115P/2116P is an expandable model which allows you to
upgrade its own capacity by additionally installing multiple peripheral devices,
such as magnetic stripe reader (MSR), fingerprint or iButton sensors, and 2nd
rear-mount POS monitor, according to your preference. The following will
give you brief instructions on how to expand on your current POS system with
these optional upgrade kits. Before proceeding with the installation of
peripherals, please make sure the POS system is completely shut down to
prevent damage.

Installing Side Mount Upgrade Kits
Located at left side on the back of your system
unit, side mount compartment is mainly used for
installation of side-mounted equipment, such as
magnetic stripe reader. For detailed installation
instructions, please refer to the user manual
specific to the device which you intend to
mount onto the terminal.
6

Installing Rear-Mount POS Monitor
RT-series POS terminal also allows you to
additionally install rear-mount POS monitor to
expand its functionality. Regarding the stepby-step instructions which aim to help you
mount it onto your POS system, Please refer
to the user manual specific to the device you
intend to install.

1.
Installing PoweredUSB or USB Hub
Please go through the below steps to complete the installation of
PoweredUSB or USB hub.
After tilting the screen all the way down, remove the system back
cover.
1.1 If the system back cover is fire-resistant, first locate the
screw as indicated in the figure, and then remove it.
Screw for Fire-Resistant
System Back Cover
1.2
2.
Hold down the release lever at the
bottom of the system back cover and
then pulling the cover outwards
To remove the stand cover from the base, grab the top side of the
cover, (1) lift the stand cover up gently, (2) pull it at a 45 degree
angle, and then (3) slide it in the horizontal direction shown by the
arrow.
2
1
3
7
3.
4.
Align the two screw bolts at the bottom of PoweredUSB or USB hub
with rail slots in the base.
Push PoweredUSB or USB hub in the
direction shown by the arrow to lock it
into place.
To remove the PoweredUSB or USB hub from the rail slots, press
down the hubs first and then push it outwards.
5.
Install power adaptor extension cable, USB cable, and power adaptor
for PoweredUSB hub.
5.1 Insert one end of the provided power
adaptor extension cable to DC Input port
of PoweredUSB hub and another end to
DC-in power jack of the terminal.
5.2
Insert mini-USB connector of the USB
cable to PoweredUSB hub and another
end to USB3.0 port of the terminal.
5.3
Connect the connector of the power
adapter to DC Output port of
PoweredUSB hub, and the other end to the
electrical outlet.
8
6.
To Install USB cable for USB hub, Plug
Type-A connector of USB cable to USB
Port of USB hub and the other end of USB
cable to USB3.0 port of the POS terminal.
7.
Neatly arrange your cable and then slide
back the stand cover.
8.
.
8.1
8.2
Place back the sytem back cover. Make sure it
is well locked into place with a click sound
For the fire-resistant system back cover, please insert another
screw into the screw hole indicated in the figure, and secure it.
Screw for Fire-Resistant
System Back Cover
9
Status LED Indicator
LED status indicator, which is located at the bottom edge of the LCD panel, is
mainly responsible for notifying users of the current system status by emitting
various LED signals. In the chart provided below, it describes all the possible
LED status as a quick reference.
15” RT-2015/2115
LED Status
Off
Green
Blue
Description
System power OFF
System standby
System power ON
15.6” RT-2016/2116
LED Status
Off
Orange
Blue
Description
System power OFF
System standby
System power ON
Powering ON/OFF RT-2015/2016/2115/2116
Power ON RT-2015/2016/2115/2116
Press down the power button to power on the POS.
Power OFF RT-2015/2016/2115/2116
In most cases, press the power button of the POS to
power the system off. If the terminal fails to turn off
the machine for unknown reasons, please be advised
to hold the power button more than 10 seconds to
force a shutdown of the system.
10
Power
Button
Installing an Operating System
You are highly advised not to install an operating system on RT2015/2016/2115/2116 without professional instructions. Improper installation
could lead to system malfunction or failure. Please contact with your dealers
about the issues of operating system installation.
Performing System Recovery
For RT-2015/2016/2115/2116 model with preloaded operating systems,
Recovery DVD which includes useful utilities will be provided in the package
to assist you in efficiently restoring or repairing your damaged system.
However, you are not encouraged to recover your system without the help of
system integrators. Please be advised to contact your service center for further
assistance with system recovery.
Operation Environment
To prevent RT-2015/2016/2115/2116 from overheating, it is suggested to
position your terminal in a well-ventilated working environment. In doing so,
please be advised to keep the POS terminal at least 25mm away from other
devices to ensure the machine is properly cooled down and functioning
normally.
11
Specifications
RT-2015/2016
CPU
System Memory
Storage Device
Power Supply
LCD Panel
LCD Resolution
Touch Sensor
Serial Port
USB Port
LAN Port
Display Port
CR Port
Audio Port
Extension Slot
vPro
TPM
RAID
Dimension
(W x V x D in mm)
Environmental
Requirements
RT-2015
RT-2016
Intel Bay Trail-D
Intel Celeron - J1900 (2.0 GHz, Quad-Core, 10W
TDP)
DDR3L, SO-DIMM socket x 1, max. 8GB
SATA Storage x 2
12V / 60W, can be upgraded to 150W while
adopting PoweredUSB module
15"TFT LCD with
15.6" TFT LCD with
LED backlight
LED backlight
1024 x 768
1920 x 1080
P-CAP touch
3 ports, DB9 x 1 + RJ-50 x 2
4 ports, USB3.0 x 1 + USB2.0 x3
Additional USB port replicator ( USB2.0 x 4,
installed in base stand)
10/100/1000 Mb x 1

eDP connector (internal header, support 15.6"
LCD)

VGA + USB + 12V (internal header,
supporting 2nd monitor 9.7"/10.1")

1 x Mini DP port (on I/O plate)
1 port, controlling 2 CR
Internal 2W speaker x 1
M.2 slot x 1
N/A
N/A
N/A
Main Unit:368 x 292 x Main Unit:402 x 251 x
46.6
41.2
with base stand :368 x with base stand :402 x
325 x 207
297 x 207
Operating:
0°C 〜 40°C, 20%RH - 90%RH (with HDD)
0°C 〜 50°C, 20%RH - 90%RH (with SSD)
Storage:
-20°C 〜 70°C, 10%RH - 90%RH
12
Regulation Rules
Attachment
RA-101
FCC/CE
RA-103
iButton (or RFID) with one USB port attachment
for RT series
2D scanner attachment for RT series
3-in-1 MSR + Fingerprint Sensor + 2D scanner
attachment for RT series
9.7" 2nd display for RT series terminal
10.1" 2nd display for RT series terminal
PoweredUSB module to support 12Vand 24V
Powered USB ports
USB port replicator ( USB2.0 x 4, installed in base
stand)
RA-104
RA-301
LM/TM-4010
LM/TM-4011
PU-460
RT-560
RT-2115/2116
CPU
System Memory
Storage Device
Power Supply
LCD Panel
LCD Resolution
Touch Sensor
Serial Port
USB Port
LAN Port
Display Port
CR Port
Audio Port
Slim MSR attachment for RT series
RT-2115
RT-2116
Intel Apollo Lake SoC
Intel Celeron - N3350 (2.4 GHz, Dual-Core, 6W
TDP)
DDR3L, SO-DIMM socket x 1, max. 8GB
SATA Storage x 2
12V / 60W, can be upgraded to 150W while
adopting PoweredUSB module
15" TFT LCD with
15.6" TFT LCD with
LED backlight
LED backlight
1024 x 768
1920 x 1080
P-CAP touch
3 ports, DB9 x 1+ RJ-50 x 2
4 ports, USB3.0 x 2 + USB2.0 x 2
Additional USB port replicator ( USB2.0 x 4,
installed in base stand)
10/100/1000 Mb x 1

eDP connector (internal header, supporting
15" and 15.6" LCD panel)

VGA + USB + 12V (internal header, support
2nd monitor 9.7"/10.1")

1 x Mini DP port (on I/O plate)
1 port, controlling 2 CR
Internal 2W speaker x 1
13
Extension Slot
vPro
TPM
RAID
Dimension
(W x V x D in mm)
Environmental
Requirements
Regulation Rules
Attachment
RA-101
RA-103
RA-104
RA-301
LM/TM-4010
LM/TM-4011
PU-460
RT-560
M.2 slot x 1
N/A
N/A
N/A
Main Unit:368 x 292 x Main Unit:402 x 251 x
46.6
41.2
with base stand :368 x with base stand :402 x
325 x 207
297 x 207
Operating:
0°C 〜 40°C, 20%RH - 90%RH (with HDD)
0°C 〜 50°C, 20%RH - 90%RH (with SSD)
Storage:
-20°C 〜 70°C, 10%RH - 90%RH
FCC/CE
Slim MSR attachment for RT series
iButton/RFID) with one USB port attachment for
RT series
2D scanner attachment for RT series
3-in-1 MSR + Fingerprint Sensor + 2D scanner
attachment for RT series
9.7" 2nd display for RT series terminal
10.1" 2nd display for RT series terminal
PoweredUSB module to support 12Vand 24V
Powered USB ports
USB port replicator ( USB2.0 x 4, installed in base
stand)
※ The product information and specifications are subject to change without
prior notice. To get the detailed information on the RT-2015/2016/2115/2116,
please check this model from Posiflex Global Website
14
<MEMO>
15
<MEMO>
16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising