Posiflex | BB-3000 | User manual | Posiflex BB-3000 User Manual

Posiflex BB-3000 User Manual
BB-3000
Bump Bar
User Manual
Package Contents
BB-3000 Bump Bar (x 1)
2m-Long Dedicated RS-232 Cable (x 1)
User Manual (x 1)
Views of the Bump Bar
Top View
SERVE Button
SERVE Button
PREV Button
NEXT Button
RECALL Button
RECALL Button
(Reserved)
SIDE OFF Button
SIDE ON Button
Bottom View
Front View
RS-232 Port
Status LED Indicator
Reset Button
Rubber Pad
Rubber Pad
Fixed Portion
19100900010 Ver. Original
1
Enabling the BB-3000
Power that enables the BB-3000 to work is supplied by your host terminal. To
make your host terminal supply power to the BB-3000, you need only a
dedicated RS-232 cable instead of a power adaptor. Thus, simply follow two
steps made below to power on the BB-3000.
1. Connect the RS-232 COM port of the BB-3000 to a specified COM port of
your host terminal through a dedicated RS-232 cable.
2. By using your dedicated application, select the specified COM port and a
baud rate.
3. Enable the COM port you selected.
Jumper Setting for a Baud Rate
To set a baud rate, please adjust the dip switch on the main board of the device.
Refer to the following steps to locate the dip switch on the main board.
1. Loosen and remove the two screws from the
top cover of BB-3000.
2. Remove the top cover.
3. You can easily find the dip switch on the
main board.
2
Functions of DIP Switch
SW1
SW6
SW2
SW7
SW3
SW8
SW4
SW9
SW5
SW10
DIP SWITCH
(Pin No.)
Pin 1
Pin 2
Pin 3
Pin 4
Pin 5
Pin 6
Functions
Baud rate settings
Pin 1/Pin 2 : OFF/OFF => 1200 bps
Pin 1/Pin 2 : OFF/ON => 2400 bps
Pin 1/Pin 2 : ON/OFF => 4800 bps
Pin 1/Pin 2 : ON/ON => 9600 bps (Default)
Code page change
Code page 1
Pin 3 : OFF / Pin 4 : OFF / Pin 5 : OFF / Pin 6 : OFF
SW1 : E2h / SW6 : E1h
SW2 : D2h / SW7 : D1h
SW3 : B2h / SW8 : B1h
SW4 : A2h / SW9 : A1h
SW5 : C2h / SW10 :C1h
Code page 2
Pin 3 : ON / Pin 4 : OFF / Pin 5 : ON / Pin 6 : OFF
SW1 : 62h / SW6 : 61h
SW2 : 52h / SW7 : 51h
SW3 : 32h / SW8 : 31h
SW4 : A2h / SW9 : A1h
SW5 : C2h / SW10 :C1h
Code page 3
Pin 3 : ON / Pin 4 : ON / Pin 5 : ON / Pin 6 : ON
SW1 : E2h / SW6 : E1h
SW2 : D2h / SW7 : D1h
SW3 : B2h / SW8 : B1h
SW4 : 22h / SW9 : 21h
SW5 : 42h / SW10 :41h
3
DIP SWITCH
(Pin No.)
Pin 7
Pin 8
Functions
Enabling or disabling DIP switch
Pin 7 : OFF / Pin 8 : OFF
Enabling SW1 ~ SW10
Pin 7 : OFF / Pin 8 : ON
Enabling SW1, SW2, SW5~SW7, and SW10
Pin 7 : ON / Pin 8 : OFF
Enabling SW3~SW5 and SW8~SW10
Regular Cleaning
For regular cleaning of the bump bar, please use only adequate amount of mild
kitchen cleaning detergent for obstinate stains and wipe it off with dry clean
soft clothes. Don’t allow any liquid to seep in through any seam in the metal
enclosure. It could also be a brilliant idea to seal the whole bump bar with thin
transparent wrap foil and replace the foil regularly.
Specifications
Buttons
10-key buttons
(8 buttons for SERVE/PREV/RECALL/SIDE
ON/SERVE/NEXT/RECALL/SIDE OFF; 2 buttons for reserved buttons)
I/O Port
DIP Switch
RS-232 COM port
8-segment dip switch
Temp
& Humidity
Operation temp.: -25 to +70 / storage temp.: -30 to +80
Humidity: 10 to 90 %; 5 to 90 % (operation condition)
℃
4
℃
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising